check engine TOYOTA SEQUOIA 2001 Service Service Manual

DI±74
± DIAGNOSTICSENGINE
268 Author: Date:
2005 SEQUOIA (RM1146U)
MONITOR DESCRIPTION
After the ECM sends the ºtargetº duty±cycle signal to the OCV (Oil Control Valve), the ECM monitors the
OCV current to establish an ºactualº duty±cycle. When the actual duty±cycle ratio varies from the target
duty±cycle, the ECM sets a DTC.
MONITOR STRATEGY
RltdDTCP0010VVT oil control valve bank 1 range checkRelated DTCsP0020VVT oil control valve bank 2 range check
Required sensors/componentsOCV
Frequency of operationContinuous
Duration1 sec.
MIL operationImmediate
Sequence of operationNone
TYPICAL ENABLING CONDITIONS
ItSpecificationItemMinimumMaximum
The monitor will run whenever this DTC is
not presentSee page DI±18
Battery voltage11 V13 V
Target duty ratio±70%
StarterOFF
Current cut statusNot cut
TYPICAL MALFUNCTION THRESHOLDS
Detection CriteriaThreshold
Either of the following conditions is met:Condition 1 or 2
1. Output signal duty for OCVOutput duty ratio is 100% (always ON) but target duty ratio is less than 70%
2. Output signal duty for OCVOutput duty is 3% or less despite the ECM supplying current to the OCV
COMPONENT OPERATING RANGE
ParameterStandard Value
Output signal duty for OCVºMore than 3%º and ºless than 100%º

A07621A09776
1
2L±W
P±LOC1+
OC1±
OC2+
OC2± 17
L±B
R±L 1
2E6 C13
OCV (Bank 1)
C14
OCV (Bank 2)ECM
16
15
14 E6
E6
E6
± DIAGNOSTICSENGINE
DI±75
269 Author: Date:
2005 SEQUOIA (RM1146U)
WIRING DIAGRAM
INSPECTION PROCEDURE
HINT:

If DTC P0010 displayed, check left bank OCV circuit.

If DTC P0020 displayed, check right bank OCV circuit.

Read freeze frame data using hand±held tester. Because freeze frame records the engine conditions
when the malfunction is detected. When troubleshooting, it is useful for determining whether the ve-
hicle was running or stopped, the engine was warmed up or not, the air±fuel ratio was lean or rich, etc.
at the time of the malfunction.

A31449A23511
Valve Battery ±
Battery +
DI±76
± DIAGNOSTICSENGINE
270 Author: Date:
2005 SEQUOIA (RM1146U)
1 Check OCV circuit.
PREPARATION:
(a) Connect the hand±held tester to the DLC3.
(b) Start the engine and warm it up.
(c) Turn the ignition switch to ON and turn the hand±held tester ON.
CHECK:
(a) Select the item: DIAGNOSIS / ENHANCED OBD II / ACTIVE TEST / VVT CTRL B1 or VVT CTRL B2.
(b) Using the hand±held tester, operate the OCV and check the engine speed.
OK:
Standard:
Tester OperationSpecified Condition
OCV is OFFNormal engine speed
OCV is ONRough idle or engine stall
OK Check for intermittent problems
(See page DI±11).
NG
2 Check operation of OCV.
PREPARATION:
(a) Start the engine and warmed it up.
(b) Disconnect the OCV connector.
(c) Apply battery positive voltage between the terminals of
the OCV.
CHECK:
Check the engine speed.
OK:
Rough idle or engine stalled.
NG Replace OCV.
OK

A02397
OCV Signal Waveform
1 msec./Division5 V/
Division
GND
(A) (A) (A)
B17414ECM ConnectorE6
OC1+
OC1±
OC2+OC2±
E1
± DIAGNOSTICSENGINE
DI±77
271 Author: Date:
2005 SEQUOIA (RM1146U)
3 Check voltage between terminals OC1+ and OC1±, OC2+ and OC2± of ECM con-
nector.
CHECK:
(a) Inspection using the oscilloscope.
(b) During idling, check the waveform between the specified
terminals of the E6 ECM connector.
HINT:
The waveform frequency (A) is lengthened as the engine speed
becomes higher.
OK:
Standard:
The correct waveform is as shown.
NG Replace ECM (See page SF±80).
OK

A23673
Wire Harness Side
C13
OCV Connector C14
B17414ECM ConnectorE6
OC1+
OC1±
OC2+OC2±
E1
DI±78
± DIAGNOSTICSENGINE
272 Author: Date:
2005 SEQUOIA (RM1146U)
4 Check for open and short in harness and connector between OCV and ECM.
PREPARATION:
(a) Disconnect the C13 or C14 OCV connector.
(b) Disconnect the E6 ECM connector.
CHECK:
(a) Check for resistance between the wire harness side con-
nectors.
OK:
Standard (Check for open):
Symbols (Terminal No.)Specified condition
OCV (C14±1) ± OC1+ (E6±17)Below 1 W
OCV (C14±2) ± OC1± (E6±16)Below 1 W
OCV (C13±1) ± OC2+ (E6±15)Below 1 W
OCV (C13±2) ± OC2± (E6±14)Below 1 W
Standard (Check for short):
Symbols (Terminal No.)Specified condition
OCV (C14±1) or OC1+ (E6±17) ± E1 (E6±1)10 kW or higher
OCV (C14±1) or OC1± (E6±16) ± E1 (E6±1)10 kW or higher
OCV (C13±1) or OC2+ (E6±15) ± E1 (E6±1)10 kW or higher
OCV (C13±1) or OC2± (E6±14) ± E1 (E6±1)10 kW or higher
NG Repair or replace harness or connector.
OK
Check for intermittent problems
(See page DI±11).

DI±80
± DIAGNOSTICSENGINE
274 Author: Date:
2005 SEQUOIA (RM1146U)
MONITOR STRATEGY
P0011VVT system advance (Bank 1)
RltdDTCP0012VVT system retard (Bank 1)Related DTCsP0021VVT system advance (Bank 2)
P0022VVT system retard (Bank 2)
Main sensors/componentsCamshaft position sensor
Required sensors/componentsRelated sensors/componentsEngine coolant temperature sensor,
Crankshaft position sensor
Frequency of operationOnce per drive cycle
Duration10 sec.
MIL operationP0011, P0021: Immediate
P0012, P0022: 2 driving cycles
Sequence of operationNone
TYPICAL ENABLING CONDITIONS
ItSpecificationItemMinimumMaximum
The monitor will run whenever these
DTCs are not presentSee page DI±18
Battery voltage11 V±
Throttle position learningCompleted
Engine RPM400 rpm4,000 rpm
Engine coolant temperature75C (167F)100C (212F)
TYPICAL MALFUNCTION THRESHOLDS
Detection CriteriaThreshold
Deviation of valve timingMore than 5CA
OCV activation63 times or more
Response of valve timing1 sec./1CA or more
WIRING DIAGRAM
Refer to DTCs P0010 on page DI±73.
INSPECTION PROCEDURE
HINT:

Bank 1 refers to bank that includes cylinder No. 1.

Bank 2 refers to bank that does not include cylinder No. 1.

If DTC P0011, P0012 is displayed, check the bank 1 VVT system.

If DTC P0021, P0022 is displayed, check the bank 2 VVT system.

Read freeze frame data using the hand±held tester. Freeze frame data records the engine conditions
when a malfunction is detected. When troubleshooting, it is useful for determining whether the vehicle
was running or stopped, the engine was warmed up or not, the air±fuel ratio was lean or rich, etc. at
the time of the malfunction.

± DIAGNOSTICSENGINE
DI±81
275 Author: Date:
2005 SEQUOIA (RM1146U)
1 Check operation of OCV.
PREPARATION:
(a) Connect the hand±held tester to the DLC3.
(b) Start the engine and warm it up.
(c) Turn the ignition switch to ON and turn the hand±held tester ON.
CHECK:
(a) Select the item: DIAGNOSIS / ENHANCED OBD II / ACTIVE TEST / VVT CTRL B1 or VVT CTRL B2.
(b) Using the hand±held tester, operate the OCV and check the engine speed.
OK:
Standard:
Tester OperationSpecified Condition
OCV is OFFNormal engine speed
OCV is ONRough idle or engine stall
OK VVT system is OK.*
*: DTC P0011, P0012, P0021 or P0022 is also output when a
foreign object is detected in some parts of the system in the en-
gine oil, and then the system returns to normal in a short time.
As ECM is controlled to eject a foreign object, there is no prob-
lem on the VVT. There is also no problem on the VVT as the oil
filter should catch the foreign object in the engine oil.
NG
2 Check valve timing (See page EM±23).
NG Adjust valve timing.
OK

A02397
OCV Signal Waveform
200 msec./Division5 V/
Division
GND
(A) (A) (A)
B17414ECM ConnectorE6
OC1+
OC1±
OC2+OC2±
E1
B12806
Ohmmeter
DI±82
± DIAGNOSTICSENGINE
276 Author: Date:
2005 SEQUOIA (RM1146U)
3 Check voltage between terminals OCV+ and OCV± of ECM connector.
CHECK:
(a) Inspection using the oscilloscope.
(b) During idling, check the waveform between the specified
terminals of the E6 ECM connector.
HINT:
The waveform frequency (A) is lengthened as the engine speed
becomes higher.
OK:
Standard:
The correct waveform is as shown.
NG Check and replace ECM (See page IN±35).
OK
4 Check OCV.
PREPARATION:
(a) Remove the V±bank cover.
(b) Remove the air cleaner inlet and intake air connector.
(c) Disconnect the oil control valve connector.
CHECK:
(a) Using an Ohmmeter, measure the resistance between
the terminals.
Resistance: 6.9 ± 7.9 W at 20°C (68°F)
NG Replace OCV, and then go to step 6.
OK

A02852
A23658
± DIAGNOSTICSENGINE
DI±83
277 Author: Date:
2005 SEQUOIA (RM1146U)
5 Check VVT controller assembly.
PREPARATION:
(a) Remove the timing belt (See page EM±16).
(b) Remove the cylinder head cover.
(c) Remove the OCV (See page SF±46).
(d) Drain the oil in the VVT controller assembly
(See page EM±36).
CHECK:
Check whether the oil in VVT controller assembly is drained or
not.
OK:
Standard:
The oil in VVT controller assembly is drained.
NG Replace VVT controller assembly, and then go
to step 6.
OK
6 Check oil control valve filter.
PREPARATION:
(a) Remove the cylinder head cover.
(b) Remove the camshaft bearing cap and OCV filter.
CHECK:
Check that the filter is not clogged.
OK:
The filter is not clogged.
NG Repair or replace.
OK

DI±84
± DIAGNOSTICSENGINE
278 Author: Date:
2005 SEQUOIA (RM1146U)
7 Check whether or not DTC P0010, P0012, P0021 or P0022 is stored.
PREPARATION:
(a) Clear the DTC (See page DI±43).
(b) Perform simulation test.
CHECK:
Check whether or not DTC P0011, P0012, P0021 or P0022 is stored (See page DI±43).
OK:
Standard: DTC P0011, P0012, P0021 or P0022 is not stored.
OK VVT system is OK.*
*: DTC P0011, P0012, P0021 or P0022 is also output when a
foreign object is detected in some parts of the system in the en-
gine oil, and then the system returns to normal in a short time.
As ECM is controlled to eject a foreign object, there is no prob-
lem on the VVT. There is also no problem on the VVT as the oil
filter should catch the foreign object in the engine oil.
NG
Replace ECM.