check engine TOYOTA SEQUOIA 2001 Service User Guide

MA001±42
± MAINTENANCEOUTSIDE VEHICLE
MA±1
48 Author: Date:
2005 SEQUOIA (RM1146U)
OUTSIDE VEHICLE
GENERAL MAINTENANCE
The owners are responsible for these maintenance and inspection items.
They can be done by the owner or they can have them done at a service shop.
These items include those which should be checked on a daily basis, those which, in most cases, do not
require (special) tools and those which are considered to be reasonable for the owner to do.
Items and procedures for general maintenance are as follows.
1. GENERAL NOTES

Maintenance items may vary from country to country. Check the owner's manual supplement in which
the maintenance schedule is shown.

Every service item in the periodic maintenance schedule must be performed.

Periodic maintenance service must be performed according to whichever interval in the periodic main-
tenance schedule occurs first, the odometer reading (miles) or the time interval (months).

Maintenance service after the last period should be performed at the same interval as before unless
otherwise noted.

Failure to do even one item can cause the engine to run poorly and increase exhaust emissions.
2. TIRES
(a) Check the pressure with a gauge.
If necessary, adjust.
(b) Check for cuts, damage or excessive wear.
3. WHEEL NUTS
When checking the tires, check the nuts for looseness or for missing.
If necessary, tighten them.
4. TIRE ROTATION (See page SA±3)
Check the owner's manual supplement in which the maintenance schedule is shown.
5. WINDSHIELD WIPER BLADES
Check for wear or cracks whenever they do not wipe clean.
If necessary, replace.
6. FLUID LEAKS
(a) Check underneath for leaking fuel, oil, water or other fluid.
(b) If you smell gasoline fumes or notice any leak, find the cause and correct.
7. DOORS AND ENGINE HOOD
(a) Check that all doors and the tailgate operate smoothly, and that all latches lock securely.
(b) Check that the engine hood secondary latch secures the hood from opening when the primary latch
is released.

MA002±35
MA±2
± MAINTENANCEINSIDE VEHICLE
49 Author: Date:
2005 SEQUOIA (RM1146U)
INSIDE VEHICLE
GENERAL MAINTENANCE
These are maintenance and inspection items which are considered to be the owner's responsibility.
They can be done by the owner or they can have them done at a service shop.
These items include those which should be checked on a daily basis, those which, in most cases, do not
require (special) tools and those which are considered to be reasonable for the owner to do.
Items and procedures for general maintenance are as follows.
1. GENERAL NOTES

Maintenance items may vary from country to country. Check the owner's manual supplement in which
the maintenance schedule is shown.

Every service item in the periodic maintenance schedule must be performed.

Periodic maintenance service must be performed according to whichever interval in the periodic main-
tenance schedule occurs first, the odometer reading (miles) or the time interval (months).

Maintenance service after the last period should be performed at the same interval as before unless
otherwise noted.

Failure to do even one item can cause the engine to run poorly and increase exhaust emissions.
2. LIGHTS
(a) Check that the headlights, stop lights, taillights, turn signal lights, and other lights are all working.
(b) Check the headlight aim.
3. WARNING LIGHTS AND BUZZERS
Check that all warning lights and buzzers function properly.
4. HORN
Check that it is working.
5. WINDSHIELD GLASS
Check for scratches, pits or abrasions.
6. WINDSHIELD WIPER AND WASHER
(a) Check operation of the wipers and washer.
(b) Check that the wipers do not streak.
7. WINDSHIELD DEFROSTER
Check that air comes out from the defroster outlet when operating the heater or air conditioner.
8. REAR VIEW MIRROR
Check that it is mounted securely.
9. SUN VISORS
Check that they move freely and are mounted securely.
10. STEERING WHEEL
Check that it has the specified free play. Be alert for changes in steering condition, such as hard steering,
excessive free play or strange noises.
11. SEATS
(a) Check that the seat adjusters operate smoothly.
(b) Check that all latches lock securely in any position.
(c) Check that the head restraints move up and down smoothly and that the locks hold securely in any
latch position.
(d) For fold±down seat backs, check that the latches lock securely.
12. SEAT BELTS
(a) Check that the seat belt system such as the buckles, retractors and anchors operate properly and
smoothly.
(b) Check that the belt webbing is not cut, frayed, worn or damaged.

MA003±50
MA±4
± MAINTENANCEUNDER HOOD
51 Author: Date:
2005 SEQUOIA (RM1146U)
UNDER HOOD
GENERAL MAINTENANCE
1. GENERAL NOTES

Maintenance items may vary from country to country. Check the owner's manual supplement in which
the maintenance schedule is shown.

Every service item in the periodic maintenance schedule must be performed.

Periodic maintenance service must be performed according to whichever interval in the periodic main-
tenance schedule occurs first, the odometer reading (miles) or the time interval (months).

Maintenance service after the last period should be performed at the same interval as before unless
otherwise noted.

Failure to do even one item can cause the engine to run poorly and increase exhaust emissions.
2. WINDSHIELD WASHER FLUID
Check that there is sufficient fluid in the tank.
3. ENGINE COOLANT LEVEL
Check that the coolant level is between the FULL and LOW lines on the see±through reservoir.
4. RADIATOR AND HOSES
(a) Check that the front of the radiator is clean and not blocked with leaves, dirt or bugs.
(2UZ±FE engine: See page CO±14)
(b) Check the hoses for cracks, kinks, rot or loose connections.
5. BATTERY ELECTROLYTE LEVEL
Check that the electrolyte level of all battery cells is between the upper and lower level lines on the case.
6. BRAKE AND CLUTCH FLUID LEVELS
Check that the brake and clutch fluid levels are near the upper level line on the see±through reservoirs.
7. ENGINE DRIVE BELTS
Check all drive belts for fraying, cracks, wear or oiliness.
8. ENGINE OIL LEVEL
Check the level on the dipstick with the engine turned off.
9. POWER STEERING FLUID LEVEL
(a) Check the level on the dipstick.
(b) The level should be in the HOT or COLD range depending on the fluid temperature.
10. AUTOMATIC TRANSMISSION FLUID LEVEL
(a) Park the vehicle on a level surface.
(b) With the engine idling and the parking brake applied, shift the selector into all positions from the P to
L, and then shift into the P position.
(c) Pull out the dipstick and wipe off the fluid with a clean rag. Re±insert the dipstick and check that the
fluid level is in the HOT range.
(d) Do this check with the fluid at normal driving temperature (70 ± 80°C, 158 ± 176°F).
HINT:
Wait until the engine cools down (approx. 30 min.) before checking the fluid level after extended driving at
high speeds, in hot weather, in heavy traffic or pulling a trailer.
11. EXHAUST SYSTEM
(a) Visually inspect for cracks, holes or loose supports.
(b) If any change in the sound of the exhaust or smell of the exhaust fumes is noticed, find the cause and
correct.

MA004±18
P08488
Back Front
± MAINTENANCEENGINE
MA±5
52 Author: Date:
2005 SEQUOIA (RM1146U)
ENGINE
INSPECTION
HINT:
Perform the following procedures when the engine is cold.
1. REPLACE TIMING BELT
(See page EM±13)
2. INSPECT DRIVE BELT
(See page CH±1)
3. REPLACE SPARK PLUGS
(See page IG±1)
4. INSPECT AIR FILTER
(a) Visually check that the air cleaner element is not exces-
sively dirty, damaged or oily.
HINT:
Oiliness may indicate a stuck PCV valve.
If necessary, replace the air cleaner element.
(b) Clean the element with compressed air.
First blow from back side thoroughly, then blow off the
front side of the element.
5. REPLACE AIR FILTER
Replace the used air cleaner element with a new one.
6. REPLACE ENGINE OIL AND OIL FILTER
(See page LU±2)
7. REPLACE ENGINE COOLANT
(See page CO±2)
8. INSPECT CHARCOAL CANISTER
(See page EC±9)
9. REPLACE GASKET IN FUEL TANK CAP
(See page SF±33)
10. INSPECT FUEL LINES, CONNECTIONS, FUEL TANK
VAPOR VENT SYSTEM HOSES AND FUEL TANK
BAND
Visually inspect the fuel lines for cracks, leakage loose connec-
tions, deformation or tank band looseness.
11. INSPECT EXHAUST PIPES AND MOUNTINGS
Visually inspect the pipes, hangers and connections for severe
corrosion, leaks or damage.
12. INSPECT VALVE CLEARANCE
(See page EM±4)

P23118Drain Plug Transfer
B07969
Differential
Front
RearDrain plug
Drain plug
B07952Drain Plug
MA0099
OK if coolOK if hot
Add if coolAdd if hot
± MAINTENANCECHASSIS
MA±9
56 Author: Date:
2005 SEQUOIA (RM1146U)
8. REPLACE TRANSFER AND DIFFERENTIAL OIL
(a) Transfer:
Remove the transfer cover.
(b) Remove the drain plug and drain the oil.
(c) Reinstall the drain plug securely.
(d) Add new oil until it reaches the bottom of the filler hole.
Transfer oil: See page TR±4
Front differential oil: See page SA-38
Rear differential oil: See page SA±129
9. REPLACE AUTOMATIC TRANSMISSION FLUID
(a) Remove the drain plug and drain the fluid.
(b) Reinstall the drain plug securely.
(c) With the engine OFF, add new fluid through the dipstick
tube.
Transmission fluid (A/T): See page DI±524
(d) Start the engine and shift the selector into all positions
from ºPº through ºLº and then shift into ºPº.
(e) With the engine idling, check the fluid level.
Add fluid up to the ºCOOLº level on the dipstick.
(f) Check that the fluid level is in the ºHOTº range at the nor-
mal operating temperature (70 ± 80°C or 158 ± 176°F)
and add as necessary.
NOTICE:
Do not overfill.
10. RECOAT FRONT WHEEL BEARINGS AND THRUST
BUSH
(a) Recoat the front wheel bearing with grease (See page
SA±28).

B02100
± MAINTENANCECHASSIS
MA±11
58 Author: Date:
2005 SEQUOIA (RM1146U)

Leaf spring U±bolt mounting nuts
Torque: 133 N´m (1,350 kgf´cm, 98 ft´lbf )
(b) Under Severe Conditions:
In addition to the above maintenance items, check for
loose or missing bolts and nuts on the following.

Steering system

Drive train

Suspension system

Fuel tank mounts

Engine mounts, etc.
14. FINAL INSPECTION
(a) Check operation of body parts:

Hood:

Auxiliary catch operates properly

Hood locks securely when closed

Doors:

Door locks operate properly

Doors close properly

Seats:

Seat adjusts easily and locks securely in any
positions

Seat backs lock securely at any angle

Fold±down seat backs lock securely
(b) Road test:

Engine and chassis parts do not have abnormal
noises.

Vehicle does not wander or pull to one side.

Brakes work properly and do not drag.
(c) Be sure to deliver a clean vehicle and especially check:

Steering wheel

Shift lever knob

All switch knobs

Door handles

Seats

PP±4
± PREPARATIONENGINE MECHANICAL
62 Author: Date:
2005 SEQUOIA (RM1146U)
09843±18040Diagnosis Check Wire No.2
09950±50013Puller C Set
(09951±05010)Hanger 150Crankshaft pulley
Crankshaft timing pulley
(09952±05010)Slide ArmCrankshaft pulley
Crankshaft timing pulley
(09953±05010)Center Bolt 100Crankshaft pulley
Crankshaft timing pulley
(09953±05020)Center Bolt 150Crankshaft pulley
Crankshaft timing pulley
(09954±05011)Claw No.1Crankshaft timing pulley
(09954±05021)Claw No.2Crankshaft pulley
09950±60010Replacer Set
(09951±00240)Replacer 24
(09951±00440)Replacer 44
(09952±06010)Adapter
09950±70010Handle Set

DID7N±01
DI±2
± DIAGNOSTICSENGINE
196 Author: Date:
2005 SEQUOIA (RM1146U)
DEFINITION OF TERMS
TermDefinition
Monitor descriptionDescription of what the ECM monitors and how it detects malfunctions (monitoring purpose and its details).
Related DTCsA group of diagnostic trouble codes that are output by the ECM based on the same malfunction detection logic..
Typical enabling condition
Preconditions that allow the ECM to detect malfunctions.
With all preconditions satisfied, the ECM sets the DTC when the monitored value(s) exceeds the malfunction
threshold(s).
Sequence of operation
The priority order that is applied to monitoring, if multiple sensors and components are used to detect the malfunc-
tion.
When a sensor is being monitored, the next sensor or component will not be monitored until the sensor monitoring
is finished.
Required sensor/compo-
nentsThe sensors and components that are used by the ECM to detect malfunctions.
Frequency of operation
The number of times that the ECM checks for malfunctions per driving cycle.
ºOnce per driving cycleº means that the ECM detects the malfunction only one time during a single driving cycle.
ºContinuousº means that the ECM detects malfunction every time an enabling condition is met.
DurationThe minimum time that the ECM must sense a continuous deviation in the monitored value(s) before setting a
DTC. This timing begins after the ºtypical enabling conditionsº are met.
Malfunction thresholdsBeyond this value, the ECM will conclude that there is a malfunction and set a DTC.
MIL operation
MIL illumination timing after a defect is detected.
ºImmediatelyº means that the ECM illuminates MIL the instant the ECM determines that there is a malfunction.
º2 driving cycleº means that the ECM illuminates MIL if the same malfunction is detected again in the 2nd driving
cycle.

DI3H8±10
Vehicle Brought to Workshop
Customer Problem Analysis P. DI±10
Problem Symptom Confirmation
If the engine does not start perform steps 10 and 12 firstConnect the OBD II scan tool or hand±held tester to DLC3.
If the display indicates a communication fault in the tool, inspect DLC3 P.DI±40
Check DTC and Freeze Frame Data
Record or Print DTC and Freeze Frame Data P. DI±43
Clear DTC and Freeze Frame Data P. DI±43
Visual Inspection
Setting the Check Mode Diagnosis P. DI±44
Symptom Simulation P. IN±24
Basic Inspection P. DI±12DTC Chart P. DI±58
Problem Symptoms Table P. DI±33
Circuit Inspection P. DI±73
Adjustment, Repair
DTC Check P. DI±43
Items insideare titles of pages in
in the bottom portion. See the indicated
pages for detailed explanations. this manual, with the page number
Malfunction
occurs.Malfunction does not occur.
Parts Inspection
Check for Intermittent Problems P. DI±11
Identification of Problem
Confirmation Test
End 1
2
3
4
5
6
7
108
9
11
12
13
15 14
16
Normal Malfunction code.
17The hand±held tester can be used at
bold frame.
± DIAGNOSTICSENGINE
DI±9
203 Author: Date:
2005 SEQUOIA (RM1146U)
HOW TO PROCEED WITH TROUBLESHOOTING
Troubleshoot in accordance with the procedure on the following page.

DI3H9±07
ENGINE CONTROL SYSTEM Check Sheet
Customer's Name
Driver's Name
Data Vehicle
Brought in
Engine model
VIN
Production Date
Licence Plate No.
Odometer Reading
Problem Symptoms
Engine does
not Start
Difficult to
Start
Poor Idling
Poor
Driveability
Engine Stall
Others
Engine does not crankNo initial combustionNo complete combustion
Engine cranks slowly
Other
Incorrect first idleIdling rpm is abnormalHigh ( rpm)Low ( rpm)
Rough idling
Other
HesitationBack fireMuffler explosion (after±fire)Surging
Knocking
Other
Soon after startingAfter accelerator pedal depressed
After accelerator pedal released
During A/C operation
Shifting from N to D
Other
Dates Problem
Occurred
Problem Frequency
Condition When
Problem Occurs
Weather
Engine Operation
Engine Temp. Place Outdoor
TemperatureConstant
Sometimes ( times per day/month)Once only
Other
Fine
CloudyRainySnowyVarious/Other
Hot
Warm CoolCold (approx. °C/ °F)
Highway
SuburbsInner cityUphillDownhill
Rough road
Other
Cold
Warming upAfter warming upAny temp.Other
Starting
Just after starting ( min.)IdlingRacing
Driving
Constant speedAccelerationDeceleration
A/C switch ON/OFF
Other
Condition of malfunction indicator lightRemains on Sometimes lights up Does not light up
NormalMalfunction code(s) (code )
Freeze frame data ( )
NormalMalfunction code(s) (code )
Freeze frame data ( )
Normal Mode
(Pre±check)
Check Mode DTC InspectionInspector's
Name
km
miles
(MIL)
DI±10
± DIAGNOSTICSENGINE
204 Author: Date:
2005 SEQUOIA (RM1146U)
CUSTOMER PROBLEM ANALYSIS CHECK