TOYOTA SEQUOIA 2001 Service Repair Manual

A23548
ECM
E4
STAR ACCR
AM28
ED I18
Ignition SWB B
B±W 1C9
620
42 P
1
B±W
B 1
J2
J/C 1
17
B±O
2D
ALTE7 J38
1FGR
W4
ED2 IA1
S3 F10
Fusible
Link Block4
W±R
B±L
Battery 5B
ST 3A
1
StarterST Relay 5
B
12 3
Instrument Panel J/B
12
Engine Room J/B
2C
5 Sub J/B No. 4
P 3A 12A36
ACC CUT Relay
to Audio
J37J/C
C
GR
4 GR
N B±R
B±R
J/C BD
J51 J52B±R
STSW
E6 IG4B
Engine Room R/B No.2
2 B
2 2
2
2 2 B±RB±R RAD No.2
1C
1C
1C
1J 1J1J
1L
1E 3
5
W±L W±R
W±R
2C
2E1
3B±R
3
B1
B±W
W±B 6
A 1
2 3 58
3
J5
J/C 1
1W±B 128 B±R
W±RJ51 BE6 11
STA W±R
21
3
S2W±R4A
4B 19
9 Sub J/B No.4 GR
P1
Park/Neutral
Position SW
AM1ACC
AM2
ST2
ECU±B
SHORT PIN
B 7
B 2AM1
1
STA8
IA5
± DIAGNOSTICSENGINE
DI±299
493 Author: Date:
2005 SEQUOIA (RM1146U)
WIRING DIAGRAM

DI±300
± DIAGNOSTICSENGINE
494 Author: Date:
2005 SEQUOIA (RM1146U)
INSPECTION PROCEDURE
HINT:
Read freeze frame data using the hand±held tester. Freeze frame data records the engine conditions when
a malfunction is detected. When troubleshooting, freeze frame data can help determine if the vehicle was
running or stopped, if the engine was warmed up or not, if the air±fuel ratio was lean or rich, as well as other
data from the time when a malfunction occurred.
1 Connect hand±held tester, and check STA signal.
PREPARATION:
(a) Connect the hand±held tester to the DLC3.
(b) Turn the ignition switch ON, and push the hand±held tester main switch ON.
(c) When using hand±held tester, enter the following menu: DIAGNOSIS / ENHANCED OBD II / DATA
LIST / ALL / STARTER SIG.
CHECK:
Read the STA signal on the hand±held tester while the starter operates.
OK:
Standard:
Ignition Switch PositionONSTART
STARTER SIGOFFON
OK Go to step 5.
NG
2 Check park/neutral position switch (See page DI±576).
NG Replace park/neutral position switch.
Go to next step 5 after the replacement.
OK
3 Check ignition switch (See page BE±24).
NG Replace ignition switch.
Go the next step 5 after the replacement.
OK

± DIAGNOSTICSENGINE
DI±301
495 Author: Date:
2005 SEQUOIA (RM1146U)
4 Connect hand±held tester, and check STA signal.
PREPARATION:
(a) Connect the hand±held tester to the DLC3.
(b) Turn the ignition switch ON, and push the hand±held tester main switch ON.
(c) On the hand±held tester, enter the following menu: DIAGNOSIS / ENHANCED OBD II / DATA LIST
/ ALL / STARTER SIG.
CHECK:
Read the STA signal on the hand±held tester while the starter operates.
OK:
Standard:
Ignition Switch PositionONSTART
STARTER SIGOFFON
NG Repair or replace harness or connector.
OK
5 Check DTC reoccur
PREPARATION:
(a) Connect the hand±held tester.
(b) Turn the ignition switch ON and hand±held tester main switch ON.
(c) Clear DTC (See page DI±43).
(d) Drive the vehicle more than 40 km/h (25 mph) for 20 seconds or more.
CHECK:
Check DTC reoccur.
RESULT:
Display (DTC Output)Proceed to
P0617A
No DTC outputB
A Replace ECM (See page SF±80).
B
Check for intermittent problems
(See page DI±11).

DI±302
± DIAGNOSTICSENGINE
496 Author: Date:
2005 SEQUOIA (RM1146U)
DTC P0630 VIN not Programmed or Mismatch ECM/PCM
CIRCUIT DESCRIPTION
DTC P0630 is set when the Vehicle Identification Number (VIN) is not stored in the Engine Control Module
(ECM) or the input VIN is not accurate. Input the VIN with the hand±held tester.
DTC No.DTC Detecting ConditionTrouble Area
P0630
VIN is not stored in ECM.

Input VIN in ECM is not accurate.ECM
MONITOR STRATEGY
Related DTCsP0630VIN not programmed
Rid / tMain sensors/componentsECMRequired sensors/componentsRelated sensors/components±
Frequency of operationContinuous
Duration0.5 sec.
MIL operationImmediate
Sequence of operationNone
TYPICAL ENABLING CONDITIONS
ItSpecificationItemMinimumMaximum
The monitor will run whenever this DTC is
not presentSee page DI±18
Battery voltage8 V±
Ignition switchON
StarterOFF
TYPICAL MALFUNCTION THRESHOLDS
Detection CriteriaThreshold
VIN codeNot programmed
COMPONENT OPERATING RANGE
ParameterStandard Value
VIN codeProgrammed
DID8E±01

± DIAGNOSTICSENGINE
DI±303
497 Author: Date:
2005 SEQUOIA (RM1146U)
INSPECTION PROCEDURE
1 Read current DTC.
NOTICE:
If P0630 is present, the VIN must be input to the ECM using the hand±held tester. However, all DTCs
are cleared automatically by the tester when inputting the VIN. If DTCs other than P0630 are present,
check them first.
NEXT
2 Input VIN with hand±held tester (See page DI±14).
NEXT
END

DI±304
± DIAGNOSTICSENGINE
498 Author: Date:
2005 SEQUOIA (RM1146U)
DTC P1340, P1341 Camshaft Position Sensor ºAº (Bank
Sensor 1)
CIRCUIT DESCRIPTION
Camshaft position sensor (G signal) consists of a magnet, iron core and pickup coil.
The camshaft drive gear (LH) has 3 teeth on its inner circumference. When the camshaft gear rotates, air
gap changes between the protrusion on the gear and the pickup coil. The change affects the magnetic field
and result in change in the resistance of the MRE element.
The crankshaft signal plate has 32 teeth and is mounted on the crankshaft. The crankshaft position sensor
generates 32 signals at every engine revolution. The ECM detects the standard crankshaft angle based on
the G signal and the actual crankshaft angle and the engine speed by the NE signal.
DTC No.DTC Detecting ConditionTrouble Area
P1340
No camshaft position sensor signal to ECM during cranking
(2 trip detection logic)
Open or short in camshaft position sensor circuit

Camshaft position sensor
P1340
P1341No camshaft position sensor signal to ECM with engine speed
600 rpm or more

Camshaft osition sensor

LH camshaft timing pulley

ECM
MONITOR DESCRIPTION
The camshaft position sensor (G signal) consists of a magnet and MRE element.
The camshaft drive gear has 5 teeth on its inner circumference. When the camshaft gear rotates, air gap
changes between the protrusion on the gear and the pickup coil. The change affects the magnetic field and
result in change in the resistance of the MRE element. The crankshaft angle sensor plate has 32 teeth and
output 32 signals every engine revolution. The ECM detects the standard crankshaft angle based on the
G signal and actual crankshaft angle and engine speed by NE signal.
MONITOR STRATEGY
RltdDTC
P1340Camshaft position sensor (Bank 1) range check
or rationality
Related DTCs
P1341Camshaft position sensor (Bank 1) range check
or rationality
Rid / tMain sensors/componentsCamshaft position sensorRequired sensors/componentsRelated sensors/componentsCrankshaft position sensor, Engine speed sensor
Frequency of operationContinuous
Duration5 sec.
MIL operationP1340 case 1 (no signal): 2 driving cycles
P1340 case 2 (mis±aligned), P1341: Immediate
Sequence of operationNone
TYPICAL ENABLING CONDITIONS
ItSpecificationItemMinimumMaximum
The monitor will run whenever these
DTCs are not presentSee page DI±18
P1340 Case 1 (No signal):
StarterON
Minimum battery voltage while starter ON±11 V
DID8F±01

A23558
C2
Crankshaft Position Sensor
*1: Shielded C1
Crankshaft Position Sensor
ECM
G±B
(*1)
(*1)VC
E2
EC
BRJ42
J/C
D
DBR 2
Y
1
2L
G
RG2+
G2±
NE+
NE± 123
E8
19
E6
29
E6
21
E6
20
E6 E
EEJ42 J/C
± DIAGNOSTICSENGINE
DI±305
499 Author: Date:
2005 SEQUOIA (RM1146U) P1340 Case 2 (Mis±aligned):
Engine RPM600 rpm±
StarterOFF
P1341:
StarterAfter OFF to ON timing
TYPICAL MALFUNCTION THRESHOLDS
Detection CriteriaThreshold
P1340 Case 1 (No signal):
Camshaft position sensor signalNo signal
P1340 Case 2 (Mis±aligned):
Crankshaft/camshaft alignment is mis±aligned (judged by comparing the crankshaft position to the camshaft position)
Camshaft position sensor signal: No input in appropriate timing.
P1341:
Crankshaft/Camshaft alignmentMis±aligned
Camshaft position sensor count12 or more / 720CA (= Engine 2 revolutions)
COMPONENT OPERATING RANGE
ParameterStandard Value
Camshaft position sensor signal input at every 720CA3
WIRING DIAGRAM

B17445
Wire Harness Side:
Camshaft Position Sensor
A23559
2 V / DIV
GND
Crank Angle
120°120° 180°
180°
60°60°
200 ms /DIV
B17414
E6ECM Connector
G2+
G2±
DI±306
± DIAGNOSTICSENGINE
500 Author: Date:
2005 SEQUOIA (RM1146U)
INSPECTION PROCEDURE
HINT:
Read freeze frame data using hand±held tester. Because freeze frame records the engine conditions when
the malfunction is detected. When troubleshooting, it is useful for determining whether the vehicle was run-
ning or stopped, the engine was warmed up or not, the air±fuel ratio was lean or rich, etc. at the time of the
malfunction.
1 Check voltage of camshaft position sensor power source circuit.
PREPARATION:
(a) Disconnect the Camshaft position sensor connector.
(b) Turn the ignition switch to ON.
CHECK:
Measure the voltage between terminal 3 of the camshaft posi-
tion sensor connector and body ground.
OK:
Standard: 4.5 to 5.5 V
NG Repair or replace harness or connector.
OK
2 Check camshaft position sensor signal.
PREPARATION:
Start the engine.
CHECK:
Check the waveform between the G2+ (E6±19) and G2±
(E6±29) of the ECM connector.
OK:
Standard: Correct waveform is as shown.
OK Replace ECM (See page IN±35).
NG

B17414
E6ECM Connector
G2+
G2±
B17445
Wire Harness Side:
Camshaft Position Sensor C1
BR3795OK NGClearance
± DIAGNOSTICSENGINE
DI±307
501 Author: Date:
2005 SEQUOIA (RM1146U)
3 Check for open and short in harness and connector between ECM and camshaft
position sensor.
PREPARATION:
(a) Disconnect the Camshaft position sensor connector.
(b) Disconnect the E6 ECM connector.
CHECK:
Measure the resistance between wire harness side connectors.
OK:
Standard:
Tester ConnectionSpecified Condition
Camshaft position sensor (C1±2) ±
G2+ (E6±19)Below 1 W
Camshaft position sensor (C1±1) ±
G2± (E6±29)Below 1 W
Camshaft position sensor (C1±2) or
G2+ (E6±19) ± Body ground10 kW or higher
Camshaft position sensor (C1±1) or
G2± (E6±29) ± Body ground10 kW or higher
NG Repair or replace harness or connector.
OK
4 Inspect sensor installation and signal plate tooth of LH camshaft timing pulley.
CHECK:
Check the camshaft position sensor installation.
OK:
The camshaft position sensor is installed properly.
NG Tighten sensor installation bolt.
OK

DI±308
± DIAGNOSTICSENGINE
502 Author: Date:
2005 SEQUOIA (RM1146U)
5 Inspect signal plate tooth of LH camshaft timing pulley.
NG Replace LH camshaft timing pulley.
OK
Replace camshaft position sensor.