oil capacity TOYOTA T100 1996 Factory User Guide

Downloaded from www.Manualslib.com manuals search engine LU−4
− LUBRICATION (5VZ−FE)OIL AND FILTER
1996 TOYOTA T100 (RM449U)
3. FILL WITH ENGINE OIL
(a) Clean and install the oil drain plug with a new gasket.
(b) Fill the engine with new oil.
Oil capacity
ItemCapacity
liters (US qts, lmp. qts)
Drain and refill
w/ Oil filter change 2WD
4WD
w/o Oil filter change 2WD
4WD
Dry fill 2WD
4WD
5.2 (5.5, 4.6)
4.7 (5.0, 4.1)
4.9 (5.2, 4.3)
4.4 (4.7, 3.9)
5.9 (6.2, 5.2)
5.5 (5.8, 4.8)
(c) Reinstall the oil filler cap.
4. START ENGINE AND CHECK FOR LEAKS
5. RECHECK ENGINE LEVEL

Downloaded from www.Manualslib.com manuals search engine MT0501
Down
ClothCounterclockwise
MT04O−02
Q06817
Installation
Front
Select Return Spring
Tip of Shift Lever
− MANUAL TRANSMISSION (R150, R150F)MANUAL TRANSMISSION UNIT (4WD)
MT−7
1996 TOYOTA T100 (RM449U)
REMOVAL
1. REMOVE TRANSMISSION SHIFT LEVER
(a) Remove the 4 screws and front console box.
(b) Remove the 4 screws and shift lever boot retainer.
(c) Cover the shift lever cap with a cloth.
(d) Then, pressing down on the shift lever cap, rotate it coun-
terclockwise to remove.
(e) Pull out the shift lever.
HINT:
At the time of installation, please refer to the following item.
Apply MP grease to the tip of the shift lever.
2. REMOVE TRANSFER SHIFT LEVER
Using snap ring pliers, remove the snap ring and pull out the
shift lever.
HINT:
At the time of installation, please refer to the following item.
Apply MP grease to the tip of shift lever.
3. RAISE VEHICLE AND DRAIN TRANSMISSION OIL
Oil grade: API GL−4 or GL−5
Viscosity: SAE 75W−90
Capacity: 2.2 liters (2.3 US qts, 1.9 Imp. qts)
Torque: 37 N·m (380 kgf·cm, 27 ft·lbf)
4. REMOVE FRONT AND REAR PROPELLER SHAFTS
(See page PR−10)
5. DISCONNECT SPEEDOMETER CABLE
6. DISCONNECT BACK−UP LIGHT SWITCH AND 4WD
INDICATOR SWITCH CONNECTORS
7. DISCONNECT CLUTCH RELEASE CYLINDER AND
LINE
Remove the 4 bolts, release cylinder and line.
Torque: 12 N·m (120 kgf·cm, 9 ft·lbf)

Downloaded from www.Manualslib.com manuals search engine R12169
SST
FA1083
SST
R04344
Less than 5 mm (0.20 in.) SA−44
− SUSPENSION AND AXLEFRONT DIFFERENTIAL REAR OIL SEAL (4WD)
1996 TOYOTA T100 (RM449U)
8. INSTALL COMPANION FLANGE
(a) Using SST, install the companion flange on the drive pin-
ion.
SST 09950−30010
(b) Apply light coat of hypoid gear oil on threads of a new
companion flange nut.
(c) Using SST to hold the flange, torque the nut.
SST 09330−00021
Torque: 108 N·m (1,100 kgf·cm, 80 ft·lbf)
9. ADJUST DRIVE PINION PRELOAD
(See page SA−57)
10. STAKE DRIVE PINION NUT
11. INSTALL FRONT PROPELLER SHAFT
(See page PR−16)
12. FILL DIFFERENTIAL WITH HYPOID GEAR OIL
Torque:
Drain plug: 49 N·m (500 kgf·cm, 36 ft·lbf)
Filler plug: 39 N·m (400 kgf·cm, 29 ft·lbf)
Oil type: Hypoid gear oil API GL−5
Recommended oil viscosity: SAE 75W−90
Capacity: 1.86 liters (1.97 US qts, 1.64 lmp. qts)
13. INSTALL ENGINE UNDER COVER

Downloaded from www.Manualslib.com manuals search engine SA0I7−02
RA10720 − 5 mm (0 − 0.20 in.) OilFiller Hole SA−154
− SUSPENSION AND AXLEREAR DIFFERENTIAL CARRIER
1996 TOYOTA T100 (RM449U)
INSTALLATION
1. INSTALL NEW GASKET TO AXLE HOUSING
2. INSTALL DIFFERENTIAL CARRIER ASSEMBLY
Install the differential carrier assembly in the axle housing.
Torque: 73 N·m (740 kgf·cm, 54 ft·lbf)
3. INSTALL PROPELLER SHAFT
2WD: See page PR−9
4WD: See page PR−16
4. INSTALL REAR AXLE SHAFTS
(See page SA−135)
5. FILL DIFFERENTIAL WITH DIFFERENTIAL OIL
Torque:
Drain plug: 49 N·m (500 kgf·cm, 39 ft·lbf)
Filler plug: 39 N·m (400 kgf·cm, 29 ft·lbf)
Oil type: Hypoid gear oil API GL−5
Recommended oil viscosity:
Above −18°C (0°F) SAE 90
Below −18°C (0°F) SAE 80W or 80W − 90
Capacity: 2.35 liters (2.22 US qts, 2.67 lmp.qts)