high beam TOYOTA VERSO 2017 User Guide

291
2-4. Toyota Safety Sense
2
When driving
VERSO_EE_OM64517E
■ The Automatic High Beam can be operated when
Vehicles without smart entry & start system
The engine switch is in the “ON” position.
Vehicles with smart entry & start system
The “ENGINE START STOP” switch is in IGNITION ON mode.
■ Front sensor detection information
● High beam may not be automatically turned off in the following situations:
• When oncoming vehicles suddenly appear from a curve
• When the vehicle is cut in front of by another
• When oncoming or preceding vehicles are hidden from sight due to
repeated curves, road dividers or roadside trees
● High beam may be turned off if an oncoming vehicle that is using fog
lights without using the headlights is detected.
● House lights, street lights, red traffic signals, and illuminated billboards or
signs may cause the high beam to turn off.
● The following factors may affect the amount of time taken to turn high
beam on or off:
• The brightness of headlights, fog lights, and tail lights of oncoming and
preceding vehicles
• The movement and direction of oncoming and preceding vehicles
• When a oncoming or preceding vehicle only has operational lights on
one side
• When a oncoming or preceding vehicle is a two-wheeled vehicle
• The condition of the road (gradient, curve, condition of the road sur-
face, etc.)
• The number of passengers and amount of luggage

292
2-4. Toyota Safety Sense
VERSO_EE_OM64517E
● High beam may be turned on or off when unexpected by the driver.
● In the situations below, the system may not be able to correctly detect the
surrounding brightness levels, and may flash or expose nearby pedestri-
ans to the high beam. Therefore, you should consider turning the high
beams on or off manually rather than relying on the Automatic High
Beam system.
• In bad weather (rain, snow, fog, sandstorms, etc.)
• The windshield is obscured by fog, mist, ice, dirt, etc.
• The windshield is cracked or damaged.
• The front sensor is deformed or dirty.
• The front sensor temperature is extremely high.
• Surrounding brightness levels are equal to those of headlights, tail
lights or fog lights.
• Vehicles ahead have headlights or tail lights that are either switched
off, dirty, are changing color, or are not aimed properly.
• When driving through an area of intermittently changing brightness and
darkness.
• When frequently and repeatedly driving ascending/descending roads,
or roads with rough, bumpy or uneven surfaces (such as stone-paved
roads, gravel tracks, etc.).
• When frequently and repeatedly taking curves or driving on a winding
road.
• There is a highly reflective object ahead of the vehicle, such as a sign
or a mirror.
• The back of a vehicle ahead is highly reflective, such as a container on
a truck.
• The vehicle’s headlights are damaged or dirty.
• The vehicle is listing or tilting, due to a flat tire, a trailer being towed,
etc.
• The driver believes that the high beam may be causing problems or
distress to other drivers or pedestrians nearby.
■ If a warning message of the Automatic High Beam is displayed...
It may indicate a malfunction in the system. Contact any authorized Toyota
dealer or repairer, or another duly qualified and equipped professional.

293
2-4. Toyota Safety Sense
2
When driving
VERSO_EE_OM64517E
WARNING
■ Limitations of the Automatic High Beam
Do not rely on the Automatic High Beam. Always drive safely, taking care to
observe your surroundings and turning high beam on or off manually if nec-
essary.
NOTICE
■ Notes when using the Automatic High Beam system
Observe the following to ensure that the Automatic High Beam functions cor-
rectly.
● Do not overload the vehicle.
● Do not modify the vehicle.

438
4-1. Maintenance and care
VERSO_EE_OM64517E
NOTICE
■ Cleaning detergents
● Do not use organic substances such as benzene or gasoline, acidic or
alkaline solutions, dye, bleach or other detergent. Doing so may discolor
the vehicle interior or cause streaks or damage to painted surfaces.
● Do not use polish wax or polish cleaner. The instrument panel’s or other
interior part’s painted surface may be damaged.
■ Preventing damage to leather surfaces
Observe the following precautions to avoid damage to and deterioration of
leather surfaces.
● Remove any dust or dirt on leather surfaces immediately.
● Do not expose the vehicle to direct sunlight for extended periods of time.
Park the vehicle in the shade, especially during summer.
● Do not place items made of vinyl, plastic, or that contain wax on the uphol-
stery, as they may stick to the leather surface if the vehicle interior heats
up significantly.
■ Water on the floor
Do not wash the vehicle floor with water.
Vehicle systems such as the audio system may be damaged if water comes
into contact with electrical components under the floor of the vehicle, and
may also cause the body to rust.
■ When cleaning the inside of the windshield (vehicles with front sensor)
Be careful not to touch the front sensor ( P. 263). If the camera is acciden-
tally scratched or hit, PCS (Pre-Collision System), LDA (Lane Departure
Alert) and Automatic High Beam may not operate properly or may cause a
malfunction.
■ Cleaning the inside of the rear window
● Do not use glass cleaner to clean the rear window, as this may cause
damage to the rear window defogger heater wires. Use a cloth dampened
with lukewarm water to gently wipe the window clean. Wipe the window in
strokes running parallel to the heater wires.
● Be careful not to scratch or damage the heater wires.

500
4-3. Do-it-yourself maintenance
VERSO_EE_OM64517E
*1: Vehicles with diesel engine
*2: Vehicles with gasoline engine
*3: Vehicles without smart entry & start system
*4: Vehicles with halogen headlights
*5: Vehicles with discharge headlights
44 EFI NO.1
7.5 A*1Multiport fuel injection system/
sequential multiport fuel injection
system
10 A*2Multiport fuel injection system/
sequential multiport fuel injection
system
45 H-LP RH HI 10 A Right-hand headlight (high beam)*4,
right-hand headlight solenoid*5
46 H-LP LH HI 10 A Left-hand headlight (high beam)*4,
left-hand headlight solenoid*5
47 H-LP RH LO
10 A*4Right-hand headlight (low beam)
15 A*5Right-hand discharge headlight
(low and high beam)
48 H-LP LH LO
10 A*4Left-hand headlight (low beam)
15 A*5Left-hand discharge headlight (low
and high beam)
49 RDI EFI*15 A Electric cooling fan(s)
50 CDS EFI*15 A Electric cooling fan(s)
FuseAmpereCircuit

506
4-3. Do-it-yourself maintenance
VERSO_EE_OM64517E
Light bulbs
You may replace the following bulbs yourself. The difficulty level of
replacement varies depending on the bulb. As there is a danger that
components may be damaged, we recommend that replacement is
carried out by any authorized Toyota dealer or repairer, or another
duly qualified and equipped professional.
■ Prepare a replacement light bulb
Check the wattage of the light bulb being replaced. ( P. 642)
■ Remove the engine compartment cover
 P. 4 5 2
■ Front bulb locations
Headlight high beam (halogen headlights)
Headlight low beam
(halogen headlights)
Front turn
signal light
Front fog light
Front position light/
daytime running light
(halogen headlights)
Side turn signal lights

512
4-3. Do-it-yourself maintenance
VERSO_EE_OM64517E
After replacing the light bulb, air cleaner duct, and/or washer
fluid filler opening, return it to the original position. ( P. 508)
■ Headlight high beam (halogen headlights)
Removing the air cleaner duct and/or moving the washer fluid
filler opening. ( P. 508)
Turn the cover to the open posi-
tion and remove it.
Open position
Turn the bulb base counterclock-
wise.

513
4-3. Do-it-yourself maintenance
4
Maintenance and care
VERSO_EE_OM64517E
Unplug the connector while pull-
ing the lock release.
Replace the light bulb, and install
the bulb base.
Align the 3 tabs on the light bulb
with the mounting, and insert.
Turn and secure the bulb base.
Shake the bulb base gently to
check that it is not loose, turn the
headlight high beam on once and
visually confirm that no light is
leaking through the mounting.
Install and turn the cover to the
closed position.
Closed position

5
553
5-2. Steps to take in an emergency
When trouble arises
VERSO_EE_OM64517E
(Flashes)

Indicates a malfunction in the PCS (Pre-Colli-
sion System) (if equipped)
A buzzer also sounds.

Indicates a malfunction in the LDA (Lane Depar-
ture Alert) (if equipped)
A buzzer also sounds.

Indicates a malfunction in the Automatic High
Beam system (if equipped)
A buzzer also sounds.
*1
(Green
indicator
flashes)
Indicates a malfunction in the clutch start sys-
tem.
A buzzer also sounds.
Warning messageDetails

5
557
5-2. Steps to take in an emergency
When trouble arises
VERSO_EE_OM64517E
*2

Indicates that, since
the VSC (Vehicle Sta-
bility Control) system
was turned off, the
pre-collision braking
and pre-collision
brake assist are dis-
abled (The pre-colli-
sion warning function
will be operational)
Turn the VSC on.
( P. 282318)
The system is tempo-
rarily canceled
because the operating
conditions of the front
sensor (temperature,
etc.) are not met.
The following systems
may be suspended:
• PCS (Pre-Collision
System) (if equipped).
• LDA (Lane Departure
Alert) (if equipped);
• Automatic High Beam
(if equipped)
The system can be
operated when the
operating conditions of
the front sensor (tem-
perature, etc.) are met.
Turn the system off,
wait for a while, and
then turn the system
back on.
The area of the wind-
shield in front of the
front sensor is fogged
up or covered with
dirt, rain, ice, snow,
etc.
The following systems
may be suspended:
• PCS (Pre-Collision
System) (if equipped).
• LDA (Lane Departure
Alert) (if equipped);
• Automatic High Beam
(if equipped)
Turn the system off,
clear the windshield of
dirt, fog, ice, etc. then
turn the system back
on. ( P. 265)
Warning messageDetailsCorrection procedure