wipers TOYOTA YARIS 2022 Owners Manual

3
HV Owner's Manual_Europe_M52N30_en
TABLE OF CONTENTS
1
6
5
4
3
2
8
7
3-5. Opening and closing the win-
dows
Power windows ................... 156
4-1. Before driving
Driving the vehicle .............. 160
Cargo and luggage ............. 166
Trailer towing (vehicles without
towing packages - including
Reunion) ........................... 167
Trailer towing (vehicles with tow-
ing packages - except for
Reunion) ........................... 167
4-2. Driving procedures
Power (ignition) s witch (vehicles
without a smart entry & start
system) ............................. 173
Power (ignition) s witch (vehicles
with a smart entry & start sys-
tem) .................................. 175
EV drive mode .................... 179
Hybrid transmission ............ 181
Turn signal lever ................. 184
Parking brake...................... 184
Brake Hold .......................... 187
4-3. Operating the lights and wip-
ers
Headlight switch.................. 190
AHB (Automatic High Beam)
.......................................... 193
Fog light switch ................... 196
Windshield wipers and washer
.......................................... 197
Rear window wiper and washer
.......................................... 200
4-4. Refueling
Opening the fuel tank cap ... 202
4-5. Using the driving support sys-
tems
Toyota Safety Sense ........... 204
PCS (Pre-Collision System) 209
LTA (Lane Tracing Assist) ... 220
Dynamic radar cruise control
with full-speed range ........ 230
Speed limiter ....................... 242
RSA (Road Sign Assist) ...... 244
BSM (Blind Spot Monitor) ... 248
Toyota parking assist-sensor
.......................................... 253
RCTA (Rear Crossing Traffic
Alert) ................................. 260
PKSB (Parking Support Brake)
.......................................... 265
Parking Support Brake function
(static objects) .................. 270
Parking Support Brake function
(rear-crossing vehicles) .... 273
Driving mode select switch . 275
GPF (Gasoline Particulate Filter)
system .............................. 276
Driving assist systems ........ 277
4-6. Driving tips
Hybrid vehicle driving tips ... 282
Winter driving tips ............... 284
4Driving

12
HV Owner's Manual_Europe_M52N30_en
Pictorial index
Pictorial index
■Exterior
Side doors ......................................................................................P.133
Locking/unlocking .............................................. ..............................P.133
Opening/closing the side windows ............................... ....................P.156
Locking/unlocking by using the mechanical key*1............................P.408
Back door ...................................................... .................................P.137
Locking/unlocking .............................................. ..............................P.139
Outside rear view mirrors ...................................... .......................P.153
Adjusting the mirror angle ..................................... ...........................P.153
Folding the mirrors ............................................ ...............................P.154
Defogging the mirrors .......................................... ............................P.290
Windshield wipers .............................................. ...........................P.197
Precautions for winter season.................................. ........................P.284
Precautions for car wash ....................................... ..........................P.313
Fuel filler door ............................................... .................................P.202

4
159
HV Owner's Manual_Europe_M52N30_en
4
Driving
Driving
4-1. Before driving
Driving the vehicle ............ 160
Cargo and luggage ........... 166
Trailer towing (vehicles without
towing packages - including
Reunion) ......................... 167
Trailer towing (vehicles with
towing packages - except for
Reunion) ......................... 167
4-2. Driving procedures
Power (ignition) switch (vehi-
cles without a smart entry &
start system) ................... 173
Power (ignition) switch (vehi-
cles with a smart entry & start
system) ........................... 175
EV drive mode .................. 179
Hybrid transmission .......... 181
Turn signal lever ............... 184
Parking brake ................... 184
Brake Hold ........................ 187
4-3. Operating the lights and wip-
ers
Headlight switch ............... 190
AHB (Automatic High Beam)
....................................... 193
Fog light switch ................. 196
Windshield wipers and washer
....................................... 197
Rear window wiper and washer
....................................... 200
4-4. Refueling
Opening the fuel tank cap. 202
4-5. Using the driving support
systems
Toyota Safety Sense ......... 204
PCS (Pre-Collision System)
........................................ 209
LTA (Lane Tracing Assist) . 220
Dynamic radar cruise control
with full-speed range ...... 230
Speed limiter ..................... 242
RSA (Road Sign Assist) .... 244
BSM (Blind Spot Monitor) . 248
Toyota parking assist-sensor
........................................ 253
RCTA (Rear Crossing Traffic
Alert) ............................... 260
PKSB (Parking Support Brake)
........................................ 265
Parking Support Brake function
(static objects) ................ 270
Parking Support Brake function
(rear-crossing vehicles) .. 273
Driving mode select switch 275
GPF (Gasoline Particulate Fil-
ter) system ...................... 276
Driving assist systems ...... 277
4-6. Driving tips
Hybrid vehicle driving tips . 282
Winter driving tips ............. 284

190
HV Owner's Manual_Europe_M52N30_en
4-3. Operating the lights and wipers
4-3.Operating the lights and wipers
Operating the switch turns
on the lights as follows:
Type A
1 The headlights, daytime
running lights ( P.190) and all
the lights listed below turn on
and off automatically.
2 The front position, tail,
license plate and instrument
panel lights turn on.
3 The headlights and all the
lights listed above (except day-
time running lights) turn on.
Typ e B
1 The headlights, daytime
running lights ( P.190) and all
the lights listed below turn on
and off automatically.
2 The front position, tail,
license plate and instrument
panel lights turn on.
3 The headlights and all the
lights listed above (except day-
time running lights) turn on.
4 The daytime running lights
turn on ( P. 1 9 0 )
■AUTO mode can be used when
The power switch is in ON.
■Daytime running light system
To make your vehicle more visible to
other drivers during daytime driving, the
daytime running lights turn on automati-
cally whenever hybrid system is started
and the parking brake is released with
Headlight switch
The headlights can be oper-
ated manually or automatically.
Operating instructions

191
4
HV Owner's Manual_Europe_M52N30_en
4-3. Operating the lights and wipers
Driving
the headlight switch in the or
position. (LED type headlights only: Illu-
minate brighter than the front position
lights.) Daytime running lights are not
designed for use at night.
■Headlight control sensor
The sensor may not function properly if an object is placed on the sensor, or
anything that blocks the sensor is affixed to the windshield.Doing so interferes with the sensor
detecting the level of ambient light and may cause the automatic headlight sys-tem to malfunction.
■Automatic light off system
●When the light switch is in or
: The headlights and front fog
lights (if equipped) turn off automati-
cally if the power switch is turned to
ACC or OFF.
●When the light switch is in : The
headlights and all lights turn off auto-
matically if the power switch is turned
to ACC or OFF.
To turn the lights on again, turn the
power switch to ON, or turn the light
switch or once and then back
to or .
■Light reminder buzzer
A buzzer sounds when the power switch
is turned to OFF or ACC and the driver’s door is opened while the lights are
turned on.
■When unlock the doors (welcome
lamp) (vehicles with LED type headlights)
When the doors are unlocked using the
entry function or wireless remote con- trol, the front position lights turn on auto-matically.
When the light switch is in the AUTO position and the surrounding area is dark, this function will operate.
■12-volt battery-saving function
In order to prevent the 12-volt battery of
the vehicle from discharging, if the light
switch is in the or position
when the power switch is turned off the
12-volt battery saving function will oper-
ate and automatically turn off all the
lights after approximately 20 minutes.
When the power switch is turned to ON,
the 12-volt battery-saving function will
be disabled.
When any of the following are per-
formed, the 12-volt battery-saving func-
tion is canceled once and then
reactivated. All the lights will turn off
automatically 20 minutes after the 12-
volt battery-saving function has been
reactivated:
●When the headlight switch is operated
●When a door is opened or closed
■Customization
Some functions can be customized.
( P.431)
NOTICE
■To prevent 12-volt battery dis- charge
Do not leave the lights on longer than necessary when the hybrid system is off.

192
HV Owner's Manual_Europe_M52N30_en
4-3. Operating the lights and wipers
1With the headlights on, push the
lever away from you to turn on
the high beams.
Pull the lever toward you to the center
position to turn the high beams off.
2 Pull the lever toward you and
release it to flash the high
beams once.
You can flash the high beams with the
headlights on or off.
This system allows the headlights
to be turned on for 30 seconds
when the power switch is off.
Pull the lever toward you and
release it with the light switch in
or after turning the power
switch off.
The lights are turned off in the fol-
lowing situations.
 The power switch is turned to
ON.
 The light switch is turned on.
 The light switch is pulled toward
you and then released.
The level of the headlights can be
adjusted according to the number
of passengers and the loading con-
dition of the vehicle.
1 Raises the level of the head-
lights
2 Lowers the level of the head-
lights
Turning on the high beam
headlights
Headlamp temporary light-
ing function
Manual headlight leveling
dial

193
4
HV Owner's Manual_Europe_M52N30_en
4-3. Operating the lights and wipers
Driving
■Guide to dial settings
Left-hand drive vehicles
Right-hand drive vehicles
*: If equipped
1Press the Automatic High Beam
switch.
Occupancy and luggage
load conditionsDial position
OccupantsLuggage
load
DriverNone0
Driver and
front pas-
senger
None0.5
All seats
occupiedNone1.5
All seats
occupied
Full lug-
gage load-
ing
2.5
Driver
Full lug-
gage load-
ing
3.5
Occupancy and luggage
load conditionsDial position
OccupantsLuggage
load
DriverNone0
Driver and
front pas-
senger
None0.5
All seats
occupiedNone1.5
All seats
occupied
Full lug-
gage load-
ing
2.5
Driver
Full lug-
gage load-
ing
3
AHB (Automatic High
Beam)*
The Automatic High Beam
uses a front camera located
behind the upper portion of the
windshield to assess the
brightness of the lights of vehi-
cles ahead, streetlights, etc.,
and automatically turns the
high beams on or off as neces-
sary.
WARNING
■Limitations of the Automatic
High Beam
Do not overly rely on the Automatic High Beam. Always drive safely, tak-
ing care to observe your surroundings and turning the high beams on or off manually if necessary.
■To prevent incorrect operation of
the Automatic High Beam system
Do not overload the vehicle.
Activating the Automatic
High Beam

194
HV Owner's Manual_Europe_M52N30_en
4-3. Operating the lights and wipers
2Turn the headlight switch to the
or position.
The Automatic High Beam indicator will come on when the system is operating.
■Conditions to turn the high beams on/off automatically
●When all of the following conditions are met, the high beams will be turned
on automatically (after approximately 1 second):• The vehicle speed is approximately 30
km/h (19 mph) or more. • The area ahead of the vehicle is dark.• There are no vehicles ahead with
headlights or tail lights turned on. • There are few streetlights on the road ahead.
●If any of the following conditions are met, the high beams will turn off auto-
matically: • The vehicle speed is below approxi-mately 25 km/h (16 mph).
• The area ahead of the vehicle is not dark.• Vehicles ahead have their headlights
or tail lights turned on. • There are many streetlights on the road ahead.
■Front camera detection information
●The high beams may not be automati-cally turned off in the following situa-
tions: • When a vehicle suddenly appears from around a curve
• When the vehicle is cut in front of by another vehicle
• When vehicles ahead cannot be
detected due to repeated curves, road dividers or roadside trees• When vehicles ahead appear in a far-
away lane on a wide road • When the lights of vehicles ahead are not on
●The high beams may be turned off if a vehicle ahead that is using fog lights
without its headlights turned on is detected.
●House lights, streetlights, traffic sig-nals, and illuminated billboards or signs and other reflective objects may
cause the high beams to change to the low beams, or the low beams to remain on.
●The following factors may affect the amount of time taken for the high
beams to turn on or off: • The brightness of the headlights, fog lights, and tail lights of vehicles ahead
• The movement and direction of vehi- cles ahead• When a vehicle ahead only has oper-
ational lights on one side • When a vehicle ahead is a two-wheeled vehicle
• The condition of the road (gradient, curve, condition of the road surface, etc.)
• The number of passengers and amount of luggage in the vehicle
●The high beams may turn on or off unexpectedly.
●Bicycles or similar vehicles may not be detected.
●In the following situations the system may not be able to correctly detect the surrounding brightness level. This
may cause the low beams to remain on or the high beams to flash or daz-zle pedestrians or vehicles ahead. In
such a case, it is necessary to manu- ally switch between the high and low beams.
• When driving in inclement weather (heavy rain, snow, fog, sandstorms, etc.)
• When the windshield is obscured by

195
4
HV Owner's Manual_Europe_M52N30_en
4-3. Operating the lights and wipers
Driving
fog, mist, ice, dirt, etc.
• When the windshield is cracked or damaged• When the front camera is deformed or
dirty • When the temperature of the front camera is extremely high
• When the surrounding brightness level is equal to that of headlights, tail lights or fog lights
• When headlights or tail lights of vehi- cles ahead are turned off, dirty, chang-ing color, or not aimed properly
• When the vehicle is hit by water, snow, dust, etc., from a preceding vehicle
• When driving through an area of inter- mittently changing brightness and darkness
• When frequently and repeatedly driv- ing ascending/descending roads, or roads with rough, bumpy or uneven
surfaces (such as stone-paved roads, gravel roads, etc.)• When frequently and repeatedly tak-
ing curves or driving on a winding road• When there is a highly reflective
object ahead of the vehicle, such as a sign or mirror• When the back of a preceding vehicle
is highly reflective, such as a con- tainer on a truck• When the vehicle’s headlights are
damaged or dirty, or are not aimed properly• When the vehicle is listing or titling
due to a flat tire, a trailer being towed, etc.• When the headlights are changed
between the high beams and low beams repeatedly in an abnormal manner
• When the driver believes that the high beams may be flashing or dazzling pedestrians or other drivers
■Switching to the high beams
Push the lever away from you.
The Automatic High Beam indicator will
turn off and the high beam indicator will
turn on.
Pull the lever to its original position to
activate the Automatic High Beam sys-
tem again.
■Switching to the low beams
Press the Automatic High Beam
switch.
The Automatic High Beam indicator will
turn off.
Press the switch to activate the Auto-
matic High Beam system again.
■Temporarily switching to the
low beams
Pull the lever toward you and then
Turning the high beams
on/off manually

196
HV Owner's Manual_Europe_M52N30_en
4-3. Operating the lights and wipers
return it to its original position.
The high beams are on while the lever
is pulled toward you, however, after the
lever is returned to its original position,
the low beams remain on for a certain
amount of time. Afterwards, the Auto-
matic High Beam will be activated
again.
■Temporarily switching to the low
beams
It is recommended to switch to the low beams when the high beam may cause
problems or distress to other drivers or pedestrians nearby.
Rear fog light switch
Turns the rear fog light on
Releasing the switch ring returns it
to .
Operating the switch ring again turns
the rear fog light off.
Fog light switch
The fog lights secure excellent
visibility in di fficult driving
conditions, such as in rain and
fog.
Operating instructions