display VOLKSWAGEN JETTA 1998 Service Manual
[x] Cancel search | Manufacturer: VOLKSWAGEN, Model Year: 1998, Model line: JETTA, Model: VOLKSWAGEN JETTA 1998Pages: 339, PDF Size: 2.35 MB
Page 235 of 339

Downloaded from www.Manualslib.com manuals search engine 01-227
V.A.G 1551
print-out Possible cause
Repair
01486
1)
The ESP driving test is
activated - Perform the complete ESP driving test;
the
- DTC will be erased automatically
- Initiate basic setting Page 01
-264
Display group number 093
01487 /
literature
1)
The ESP driving test time
has been exceeded - Perform the complete ESP driving test
within the allowed time
1) For ABS/EDL/ASR/ESP and ABS/EDL/ASR/ESP 4MOTION
Стр. 69из 129 On Board Diagnostic (OBD), performing
Page 236 of 339

Downloaded from www.Manualslib.com manuals search engine 01-228
V.A.G 1551 print-
out Possible cause
Repair
01542
Sender for rotation
rate -G202-
Implausible signal
1)
- Read measured value block
Page 01
-240 Display group number
004
Installation of sender for
rotation rate -G202- is not
OK. - Check installation of sender for
rotation rate -G202-
Open circuit, short to positive
or Ground in the wiring - Check wiring and connections using
wiring diagram
- Perform electrical check Page
01-288
Sender for rotation rate -
G202- faulty
Repair Manual, Brake System,
Repair Group 45 - Replace sender for rotation rate -
G202-
1) For ABS/EDL/ASR/ESP and ABS/EDL/ASR/ESP 4MOTION
Стр. 70из 129 On Board Diagnostic (OBD), performing
Page 238 of 339

Downloaded from www.Manualslib.com manuals search engine 01-230
Diagnostic Trouble Code (DTC)
memory, erasing and ending output
Note:
All functions which could previously be
performed with V.A.G 1551 can now also
be carried out with the tester VAS 5051.
Prerequisites:
DTC memory checked Page 01-
170 .
1. Erasing DTC memory
-
Press key.
Rapid data transfer HELP
Select function XX Indicated on display:
- Press keys -0- and -5-; 05 enters the
"Erase DTC memory" function.
Rapid data transfer Q
05 Erase DTC memor
y
Indicated on display:
- Confirm entry with Q key
Rapid data transfer
DTC memory is erased!
Indicated on display:
-
Press key.
Rapid data transfer HELP
Select function XX Indicated on display:
Стр. 72из 129 On Board Diagnostic (OBD), performing
Page 239 of 339

Downloaded from www.Manualslib.com manuals search engine 01-231
Warning!
DTC memor
y was not interrogated.
Indicated on display:
Note:
Adhere exactly to test sequence: First
check DTC, then erase
2. Ending output
- Press keys -0- and -6-, this ends the
output.
Rapid data transfer Q
06 - End out
put
Indicated on display
- Confirm input with Q key.
Rapid data transfer HELP
Select function XX Indicated on display:
ABS warning light -K47- must go out after
approx. 2 seconds. - Switch off ignition.
- Disconnect Connection to V.A.G 1551
scan tool.
- Switch on ignition.
Стр. 73из 129 On Board Diagnostic (OBD), performing
Page 240 of 339

Downloaded from www.Manualslib.com manuals search engine 01-232
ABS control module, coding
Note:
All functions which could previously be
performed with V.A.G 1551 can now also be
carried out with the tester VAS 5051.
ABS warning light -K47- and warning light for
brake system -K118- flash when ABS control
module (w/EDL) -J104- is coded with 00000. An
entry is not made in the DTC memory.
The ABS control module (w/EDL) -J104- must
be recoded if the vehicle relevant coding is not
displayed or the control module has been
replaced.
Coding is only possible after the workshop code
(WSC) has been introduced into V.A.G 1551.
Стр. 74из 129 On Board Diagnostic (OBD), performing
Page 241 of 339

Downloaded from www.Manualslib.com manuals search engine 01-233
Test sequence
- Connect V.A.G 1551 scan tool and select
(address word 03) brake electronics control
module with ignition switched on; Page 01
-
163 .
- Establish engine code.
Rapid data transfer HELP
Select function XX Indicated on display:
- Input 07 for the function "Code control module"
and confirm with Q key.
Rapid data transfer Q
07 - Code control module Indicated on display:
- Confirm input with Q key.
Coding control module Q
Enter code number XXXXX
(0-32000)
Indicated on display:
- Enter the relevant code number for this vehicle
and confirm with Q key.
Coding variations Page 01
-236 .
1C0 907 379E ESP FRONT MK60 0103
Coding 0011266 WSC 00000
On the display the control module identification and
coding are displayed , e.g.:
Стр. 75из 129 On Board Diagnostic (OBD), performing
Page 248 of 339

Downloaded from www.Manualslib.com manuals search engine 01-240
Measured value block, reading
Note:
All functions that have been carried out so far
with V.A.G 1551 can now also be carried out with
the tester VAS 5051.
The control module can transfer a considerable
amount of test data. This test data delivers
information on the operational condition of the
system and/or sensors connected to it. In many
cases the transferred test data supports
troubleshooting and repair. The test data has
been summarized into single display groups
because all the information cannot be evaluated
at the same time. The information can be
selected via display group numbers.
Safety precautions
WARNING!
If the use of test and information devices
during a test drive is necessary, observe the
following:
You must always secure testing and
measuring equipment on the rear seat.
When vehicle is being driven, a second
technician must operate this equipment.
Стр. 82из 129 On Board Diagnostic (OBD), performing
Page 249 of 339

Downloaded from www.Manualslib.com manuals search engine 01-241
- Connect V.A.G 1551 scan tool and select
(address word 03) brake electronics control
module with ignition switched on; Page 01
-
163 .
Rapid data transfer HELP
Select function XX Indicated on display:
- Press keys 0 and 8. (The function "Read
measured value block" is initiated with 08.)
Rapid data transfer Q
08 - Read measured value block Indicated on display:
- Confirm entry with key Q.
Read measured value block
Enter displa
y group number XXX
Indicated on display:
- Enter display group number. List of selectable
display group numbers Page 01
-242 .
Стр. 83из 129 On Board Diagnostic (OBD), performing
Page 250 of 339

Downloaded from www.Manualslib.com manuals search engine 01-242
Overview of selectable display group numbers
Display group number
Display zone
Designation
001 1 Wheel speed at left front wheel sensor (km/h)
2 Wheel speed at right front wheel sensor (km/h)
3 Wheel speed at left rear speed sensor (km/h)
4 Wheel speed at right rear speed sensor (km/h)
002 1 Wheel speed at left front speed sensor (km/h)
2 Wheel speed at right front wheel sensor (km/h)
3 Wheel speed at left rear speed sensor (km/h)
4 Wheel speed at right rear speed sensor (km/h)
003 1 Brake light switch
2 Brake system warning light
3 ABS warning light
4 ASR/ESP warning light
Стр. 84из 129 On Board Diagnostic (OBD), performing
Page 251 of 339

Downloaded from www.Manualslib.com manuals search engine 01-243
Display group number
Display zone
Designation
004 1 Steering angle sensor
2 Lateral accelerator sensor
3 Sender for rotation rate
4 Vacant
005 1 Brake pressure sensor
2 Vacant
3 Vacant
4 Vacant
Стр. 85из 129 On Board Diagnostic (OBD), performing