ignition VOLKSWAGEN JETTA 1998 User Guide
[x] Cancel search | Manufacturer: VOLKSWAGEN, Model Year: 1998, Model line: JETTA, Model: VOLKSWAGEN JETTA 1998Pages: 339, PDF Size: 2.35 MB
Page 35 of 339

Downloaded from www.Manualslib.com manuals search engine 01-32
Note:
The ABS function is switched off in the control
module during the On Board Diagnostic.
The DTC memory can be erased after
successful checking and repair.
Note:
Operating instructions for Vehicle Diagnosis,
Testing and Information System VAS 5051. - Pull cover -1- off in direction of -arrow-.
- With ignition switched off, connect tester VAS
5051 to diagnosis connection using diagnosis
cable VAS 5051/1 or VAS 5051/3.
In the functions 04 - Basic setting/08 - Read
Measured value block, the display zones will b
e
listed from top to bottom.
If the display does not indicate as described in
the work sequence:
Стр. 12из 81 ABS ITT Mk 20 IE On Board Diagnostic (OBD) program
Page 41 of 339

Downloaded from www.Manualslib.com manuals search engine 01-38
V.A.G 1551
print-out Possible cause
Repair
00283
Left front ABS
wheel speed
sensor -G47-
Signal outside
tolerances
1)
Open circuit, short to positive or
Ground, or loose contact in
connections between left front ABS
wheel speed sensor -G47- and ABS
Control Module (w/EDL) -J104- - Check wiring and
connections using wiring
diagram
- Perform electrical checks
from Page 01
-102
Electrical interference from other
sources (high frequency radiation e.g.
non-insulated ignition cable) - Read measured value block
Page 01
-61 Display group
number 001
Damaged rotor or left front ABS wheel
speed sensor -G47-
Excessive air gap between left front
ABS wheel speed sensor-G47- and
rotor (signal not OK.)
Repair Manual, Brake
System, Repair Group 45;
Removing and installing parts
of ABS system on front and
rear axles - Check left front ABS wheel
speed sensor -G47- and rotor
for damage
- Replace rotor/speed sensor
1) Type of DTC, this DTC is only recognized above 20 km/h (13 mph) (carry out test drive).
Стр. 18из 81 ABS ITT Mk 20 IE On Board Diagnostic (OBD) program
Page 44 of 339

Downloaded from www.Manualslib.com manuals search engine 01-41
V.A.G 1551
print-out Possible cause
Repair
00285
Right front ABS
wheel speed
sensor -G45-
Signal outside
tolerances
1)
Open circuit, short to positive or
Ground, or loose contact in
connections between right front ABS
wheel speed sensor -G45- and ABS
Control Module (w/EDL) -J104- - Check wiring and
connections using wiring
diagram
- Perform electrical checks
from Page 01
-102
Electrical interference from other
sources (high frequency radiation e.g.
non-insulated ignition cable) - Read measured value block
Page 01
-61 Display group
number 001
Damaged rotor or right front ABS
wheel speed sensor -G45-
Excessive air gap between right front
ABS wheel speed sensor-G45- and
rotor (signal not OK)
Repair Manual, Brake
System, Repair Group 45;
Removing and installing parts
of ABS system on front and
rear axles - Check right front ABS wheel
speed sensor -G45- and rotor
for damage
- Replace rotor/speed sensor
1) Type of DTC, this DTC is only recognized above 20 km/h (13 mph) (carry out test drive).
Стр. 21из 81 ABS ITT Mk 20 IE On Board Diagnostic (OBD) program
Page 47 of 339

Downloaded from www.Manualslib.com manuals search engine 01-44
V.A.G 1551
print-out Possible cause
Repair
00287
Right rear ABS
wheel speed
sensor -G44-
Signal outside
tolerances
1)
Open circuit, short to positive or
Ground, or loose contact in
connections between right rear ABS
wheel speed sensor -G44- and ABS
Control Module (w/EDL) -J104- - Check wiring and
connections using wiring
diagram
- Perform electrical checks
Page 01
-102
Electrical interference from other
sources (high frequency radiation e.g.
non-insulated ignition cable) - Read measured value block
Page 01
-61 Display group
number 001
Damaged rotor or right rear ABS
wheel speed sensor -G44-
Excessive air gap between right rear
ABS wheel speed sensor -G44- and
rotor (signal not OK.)
Repair Manual, Brake
System, Repair Group 45;
Removing and installing parts
of ABS system on front and
rear axles - Check right rear ABS wheel
speed sensor -G44- and rotor
for damage
- Replace rotor/speed sensor
1) Type of DTC, this DTC is only recognized above 20 km/h (13 mph) (carry out test drive).
Стр. 24из 81 ABS ITT Mk 20 IE On Board Diagnostic (OBD) program
Page 50 of 339

Downloaded from www.Manualslib.com manuals search engine 01-47
V.A.G 1551
print-out Possible cause
Repair
00290
Left rear ABS
wheel speed
Sensor -G46-
Signal outside
tolerances
1)
Open circuit, short to positive or
Ground, or loose contact in
connections between left rear ABS
wheel speed sensor -G46- and ABS
Control Module (w/EDL) -J104- - Check wiring and
connections using wiring
diagram
- Perform electrical checks
Page 01
-102
Electrical interference from other
sources (high frequency radiation e.g.
non-insulated ignition cable) - Read measured value block
Page 01
-61 Display group
number 001
Damaged rotor or left rear ABS wheel
speed sensor -G46-
Excessive air gap between left rear
ABS wheel speed sensor -G46- and
rotor (signal not OK.)
Repair Manual, Brake
System, Repair Group 45;
Removing and installing parts
of ABS system on front and
rear axles - Check left rear ABS wheel
speed sensor -G46- and rotor
for damage
- Replace rotor/speed sensor
1) Type of DTC; this DTC is only recognized above 20 km/h (13 mph) (carry out test drive).
Стр. 27из 81 ABS ITT Mk 20 IE On Board Diagnostic (OBD) program
Page 53 of 339

Downloaded from www.Manualslib.com manuals search engine 01-50
V.A.G 1551
print-out Possible cause
Repair
01130
ABS
operation
Implausible
signal
1)
Electrical interference from
other sources (high
frequency radiation e.g.
non-insulated ignition cable)- Erase DTC memory
- Perform test drive at more than 20 km/h
(13 mph)
- Check DTC memory again
Open circuit, short to
positive or Ground in the
wiring - Check wiring and connections using wiring
diagram
- Perform electrical checks Page 01
-102
If the malfunction occurs again:
ABS Control Module
(w/EDL) -J104- faulty
Repair Manual, Brake System, Repair
Group 45; Hydraulic unit, brake
booster/brake master cylinder - Assembly
overview; Removing and installing control
module and hydraulic unit - Replace ABS control module (w/EDL) -
J104-
1) Type of DTC; this DTC is only recognized above 20 km/h (13 mph) (carry out test drive).
Стр. 30из 81 ABS ITT Mk 20 IE On Board Diagnostic (OBD) program
Page 55 of 339

Downloaded from www.Manualslib.com manuals search engine 01-52
V.A.G 1551
print-out Possible cause
Repair
01312
Drive train data
bus faulty
1)
or:
ABS control module (w/EDL) -
J104- incorrectly coded
Engine control module
incorrectly coded
Repair group 01 for relevant
engine code - Check ABS control module
(w/EDL) -J104- coding Page 01
-
58
- Check engine control module
coding
Open circuit, short to positive or
Ground in the wiring - Check wiring and connections
using wiring diagram
- Perform electrical checks Page
01-102
Drive train data
bus faulty
1)
Sporadic
Ignition/starter switch turned
too slowly - Erase DTC memory Page 01-56
- No further measures required
- Inform customer
1) The DTC "Drive train data bus" will not cause the ABS warning light -K47- or warning light for
brake system -K118- to light up. The ABS function is retained over the complete range.
Стр. 32из 81 ABS ITT Mk 20 IE On Board Diagnostic (OBD) program
Page 58 of 339

Downloaded from www.Manualslib.com manuals search engine 01-55
V.A.G 1551
print-out Possible cause
Repair
18256
Check Engine
Control Module
(ECM) memory
DTC in ECM
Repair Manual, Fuel Injection & Ignition, Repair
Group 01 for relevant engine code - Check engine control module DTC memory
65535
Control module
faulty ABS Control
Module (w/EDL)
-J104- faulty Repair Manual, Brake System, Repair Group 45;
Hydraulic unit, brake booster/brake master cylinder -
Assembly overview; Removing and installing control
module and hydraulic unit - Replace ABS control module (w/EDL) -J104-
Стр. 35из 81 ABS ITT Mk 20 IE On Board Diagnostic (OBD) program
Page 60 of 339

Downloaded from www.Manualslib.com manuals search engine 01-57
Warning!
DTC memor
y was not interrogated.
Indicated on display
Note:
Adhere exactly to test sequence: First
check DTC memory, then erase
2. Ending output
- Press keys -0- and -6-, to end output.
Rapid data transfer Q
06 - End output Indicated on display
- Confirm input with Q key.
Rapid data transfer HELP
Select function XX Indicated on display
ABS warning light -K47- and warning light
for brake system -K118- must go out after
approx. 2 seconds. - Switch ignition off.
- Disconnect V.A.G 1551 Scan Tool at
Data Link Connector (DLC).
- Switch ignition on.
Стр. 37из 81 ABS ITT Mk 20 IE On Board Diagnostic (OBD) program
Page 61 of 339

Downloaded from www.Manualslib.com manuals search engine 01-58
ABS control module, coding
All functions which could previously be
performed with V.A.G 1551 can also be
performed with the tester VAS 5051.
Warning light for ABS -K47- and warning light
for brake system -K118- flash when control
module is coded with 00000. An entry is not set
in the DTC memory.
The ABS control module (w/EDL) -J104- must
be recoded if the vehicle relevant coding is not
displayed or the control module has been
replaced.
Coding is only possible after the workshop code
(WSC) has been entered into the V.A.G 1551
Scan Tool.
Test sequence
- Connect V.A.G 1551 Scan Tool and select
(address word 03) "Brake electronics" with
ignition switched on; Page 01
-23
- Establish which type of ABS hydraulic control
module is installed Page 01
-4 .
- Establish engine code.
Стр. 38из 81 ABS ITT Mk 20 IE On Board Diagnostic (OBD) program