lock VOLKSWAGEN PASSAT 1995 B3, B4 / 3.G Service Service Manual

Downloaded from www.Manualslib.com manuals search engine 45-5

Wheel speed sensor and rotor for speed
sensor, removing and installing

Speed sensor
When installing speed sensor ensure wiring is
not twisted.
Before installing speed sensor, clean mounting
hole and coat with lubricating paste, G 000 650.
Rotors
Before installing check that rotor is clean and
undamaged.

Front axle
Vehicles with base suspension Page 40-14 . Vehicles with plus suspension Page 40-23 .
Rear axle
Vehicles with rear drum brakes Page 42-15 . Vehicles with rear disc brakes (front and four
wheel drive Page 42-24 . Page 5 of 5Anti-locking Brake System (ABS) and Anti-locking Brake System with Electronic Differential Lock (A...12/7/2004http://ebahn.bentleypublishers.com/vw/servlet/Display?action=Goto&type=repair&id=VW.B4.SU01.45.1

Downloaded from www.Manualslib.com manuals search engine 45-6


Anti-lock Brake System (ABS)
and ABS with Electronic
Differential Lock (ABS/EDL),
Teves 20 GI

General information The ABS or ABS/EDL braking system is divided
diagonally. Brake pedal pressure is boosted
pneumatically, by the vacuum brake booster.
Vehicles with Teves 20 GI ABS or ABS/EDL do not
have a mechanical brake pressure regulator.
Specially matched software in the ABS control
module regulates rear axle brake pressure. The ABS hydraulic unit -a- and ABS control module -
b- together make up one component. Separating
them for service is only possible after the assembly
has been removed.
New ABS control units supplied as replacement parts
from the Parts department are not coded, and require
coding after installation:
Repair Manual, Brake System On Board Diagnostic (OBD), Repair Group 01
Malfunctions of the ABS or ABS/EDL system do not
influence the brake system or the vacuum brake
booster. The conventional brake system remains
functional even without ABS.
Before working on the ABS or ABS/EDL system,
determine the cause of the malfunction using the On
Board Diagnostic (OBD) program % Repair Manual,
ABS & ABS/EDL On Board Diagnostic. Page 1 of 3Anti-lock Brake System (ABS) and ABS with Electronic Differential Lock (ABS/EDL), Teves 20 GI12/7/2004http://ebahn.bentleypublishers.com/vw/servlet/Display?action=Goto&type=repair&id=VW.B4.SU01.45.2

Downloaded from www.Manualslib.com manuals search engine 45-7

Safety precautions

WARNING!

Brake fluid is poisonous.

CAUTION!
Before working on the ABS or ABS/EDL
system, disconnect the battery Ground
(GND) strap. For anti-theft coded radios, first
make sure that the radio code is available.
Brake fluid must not contact painted parts. Brake fluid absorbs moisture from the air
and must therefore be replaced every two
years. Use only new, approved brake fluid
that complies with MVSS 116 DOT 4.
DO NOT use silicone-brake fluid (DOT 5).
Even the smallest traces can cause sever
corrosion in the brake system.
Before doing any welding repairs on the
vehicle using electric welding equipment,
disconnect the ABS control module.
After work that requires opening the brake
hydraulic system, bleed the system Page 47-29 . Page 2 of 3Anti-lock Brake System (ABS) and ABS with Electronic Differential Lock (ABS/EDL), Teves 20 GI12/7/2004http://ebahn.bentleypublishers.com/vw/servlet/Display?action=Goto&type=repair&id=VW.B4.SU01.45.2

Downloaded from www.Manualslib.com manuals search engine 45-8

CAUTION!
During the final road test, make sure that at
least one controlled brake test is included
(pulsations must be felt at the brake pedal).
Absolute cleanliness is required when
working on the ABS or ABS/EDL system. DO
NOT use any products that contain mineral
oil, such as oils, greases, etc.
Thoroughly clean all connections and the
immediate vicinity before loosening. DO NOT
use aggressive cleaning agents such as
brake cleaner, gasoline or thinners.
Place removed parts on a clean surface and
cover. DO NOT use fluffy cloths.
Carefully seal or cover opened components
if a repair cannot be completed immediately.
After separating the ABS hydraulic unit and
ABS control module, always use the plastic
foam transportation protection for the valve
dome, and always use the sealing plug kit
Part No. 1 H0 693 311 A.
Only install replacement parts that were
packed in their original packaging. Only
remove them immediately before installation. When the hydraulic system is open DO NOT
work with compressed air in the vicinity and
DO NOT move the vehicle.
Take precautions to make sure that brake
fluid does not enter any wiring harness
connectors. Page 3 of 3Anti-lock Brake System (ABS) and ABS with Electronic Differential Lock (ABS/EDL), Teves 20 GI12/7/2004http://ebahn.bentleypublishers.com/vw/servlet/Display?action=Goto&type=repair&id=VW.B4.SU01.45.2

Downloaded from www.Manualslib.com manuals search engine 45-9

ABS, ABS/EDL
hydraulic unit,
vacuum brake
booster and brake
master cylinder
(Teves 20 GI),
servicing
CAUTION!
DO NOT separate the ABS
hydraulic pump from the
valve block.
1 - Brake servo (vacuum
brake booster)
2 - Brake master cylinder
3 - Brake fluid reservoir
4 - Cap
5 - Self-locking nut Always replace 25 Nm (18 ft lb) 6 - Torx socket-head
bolt T25 4 Nm (35 in lb) 7 - Torx socket-head
bolt T25 8 Nm (71 in lb) Page 1 of 9ABS, ABS/EDL hydraulic unit, vacuum brake booster and brake master cylinder (Teves 20 GI), servicing12/7/2004http://ebahn.bentleypublishers.com/vw/servlet/Display?action=Goto&type=repair&id=VW.B4.SU01.45.3

Downloaded from www.Manualslib.com manuals search engine 45-18

Assembly overview
- hydraulic unit,
brake servo/brake
master cylinder
Note:
Repair Manual, Brake System On Board Diagnostic (OBD), Repair group 01 Pump and valve block must
not be separated from one
another. Illustration shows an
exploded view of the
ABS/EDL unit. Servicing of
ABS unit is identical.
Distinguishing features 1 - Brake Pedal Position
Sensor Removing and
installing Page 45-25 . Checking Page 1 of 10Assembly overview - hydraulic unit, brake servo/brake master cylinder12/7/2004http://ebahn.bentleypublishers.com/vw/servlet/Display?action=Goto&type=repair&id=VW.B4.SU01.45.4

Downloaded from www.Manualslib.com manuals search engine 45-20

Repair Manual, Brake System On Board Diagnostic (OBD), Repair group 01 12 - Cap
13 - Hex socket head screw for brake fluid
reservoir
14 - Series resistor Only on vehicles with
ABS/EDL Checking 15 - Self-locking hex nut, 25 Nm (18 ft lb)
16 - Tandem brake master
cylinder
17 - Protective plate
18 - Hex bolt for protective
plate Page 3 of 10Assembly overview - hydraulic unit, brake servo/brake master cylinder12/7/2004http://ebahn.bentleypublishers.com/vw/servlet/Display?action=Goto&type=repair&id=VW.B4.SU01.45.4

Downloaded from www.Manualslib.com manuals search engine 45-26

Removing

- Release brake servo vacuum by operating the
brake pedal several times.

- Remove connector from expansion tank.
- Swing coolant expansion tank to side.
- Pull connector off sensor. - Expand circlip with a small screwdriver in a
clockwise direction and pull sensor (arrow) out of
brake servo. Page 9 of 10Assembly overview - hydraulic unit, brake servo/brake master cylinder12/7/2004http://ebahn.bentleypublishers.com/vw/servlet/Display?action=Goto&type=repair&id=VW.B4.SU01.45.4

Downloaded from www.Manualslib.com manuals search engine 46-5

14 - Self-locking hex bolt,
35 Nm (26 ft lb) Always replace 15 - Guide pin
16 - Ribbed bolt, 125 Nm
(92 ft lb)
17 - Protective cap
18 - Hex socket head bolt,
10 Nm (7 ft lb)
19 - Speed sensor Only on vehicles with
ABS Before inserting sensor clean mounting hole inner surface and
coat with lubricating
paste, G 000 650 Page 5 of 7Front brakes, servicing (Girling caliper)12/7/2004http://ebahn.bentleypublishers.com/vw/servlet/Display?action=Goto&type=repair&id=VW.B4.SU01.46.1

Downloaded from www.Manualslib.com manuals search engine 46-7

Installing

Note:
Before inserting new brake pads, press piston
back into the cylinder with resetting tool. Before
pressing the piston back, remove some brake
fluid from the reservoir with a bleeder bottle. If
reservoir has been topped up, fluid may overflow
and cause damage. Note: - Press piston back. - Install brake pads. - Swing brake caliper housing down and tighten bolt. The repair kit contains two self-locking bolts which must always be installed. After replacing the brake pads, depress brake
pedal firmly several times with the vehicle
stationary so that the brake pads are properly
seated in their normal operating position. Page 7 of 7Front brakes, servicing (Girling caliper)12/7/2004http://ebahn.bentleypublishers.com/vw/servlet/Display?action=Goto&type=repair&id=VW.B4.SU01.46.1