sensor VOLKSWAGEN T-ROC 2021 Owner´s Manual

⇒ Tyre
pressure . If the tyre pressure is too low, it is possible that the tyre temperature will increase to such
an extent that the tread peels off and the tyre bursts.
⇒ Tyre pressure .
eck the tyre pressure regularly when the tyres are cold. If necessary, adjust the tyre pressure in
the cold tyre to the recommended tyre pressure for the tyres installed on your vehicle ⇒ Tyre
pressure .
amage.


If the tyre pressure is too low, this will increase fuel consumption and tyre wear.

When new tyres are driven at high speeds for the first time, they can expand slightly and trigger a
one-off pressure warning.

Old tyres should be replaced only by tyres that have been approved by Volkswagen for the vehicle
type.

Do not rely solely on the tyre monitoring system. Check your tyres regularly to ensure that they are
properly inflated and have no signs of damage, such as punctures, cuts, cracks, and blisters. Remove
any objects that become embedded in the tyre tread but have not penetrated into the body of the
tyre itself.
Tyre Pressure Loss Indicator
First read and observe the introductoryinformation and safety warnings⇒Introduction 
Functional description
The Tyre Pressure Loss Indicator uses data from the ABS sensors and other functions to compare the
speed of rotation and the rolling circumference of the individual wheels.
The rolling circumference can change:

WARNING
Care products may be toxic and hazardous. Unsuitable care products and incorrect application of
care products can cause accidents, severe injuries, burns or poisoning.

facturer's instructions.

-ventilated rooms so that you do not breathe in any toxic
vapours.
e fluids for vehicle care.
These substances are toxic and highly inflammable.

NOTICE
Soiling with aggressive and solvent-based ingredients can cause irreparable damage to the vehicle
equipment, even if left for only a short time, e.g. on seat padding or trim parts.


1) Suitable accessories are available from your Volkswagen dealership. Follow the application
instructions on the packaging.
Washing the vehicle
Thoroughly wash the underside of the vehicle on a regular basis to remove road salt or sea water
residue.
Automatic car washes
Always observe all the car wash operator's specifications, particularly if your vehicle has add-on
parts ⇒ .
ar washes without brushes.

⇒ Information on
steering .
⇒ Operating the wiper lever  and the rain/light sensor before using
the car wash.


High-pressure cleaner

Sensors, camera lenses:
clean the area in front of the sensors or camera with a soft cloth and solvent-free cleaning agent.
Observe the installation locations ⇒ Vehicle overviews .


camera lens.
Clean sensitive surfaces on the rain/light sensor and the camera window on the windscreen in the
same way as windows and glass surfaces (depending on vehicle equipment).
Remove snow with a hand brush. Do not use warm or hot water. Use the Volkswagen Genuine de-
icing agent (- 000 096 322 -) to remove ice.
Decorative films, protective films:
Remove soiling as for paint. Always use Volkswagen Genuine plastic cleaner (- 000 096 314 -) for
matt decorative films.
Treat the vehicle with liquid hard wax every three months after washing and removing dust. Use
only clean, soft microfibre cloths to apply it. Do not use hot wax, even in car washes.

Trim parts, trim strips, exhaust pipes made of chrome, aluminium or stainless steel:
Clean only using a clean, soft cloth and a mild soap solution2) in a dust-free environment.
Chrome parts can be protected using Volkswagen Genuine hard wax (- 000 096 317 -).
Anodised surfaces: do not use chrome cleaning products.
Headlights, tail light clusters:
Use a soft sponge soaked with a mild soap solution2). Do not use any cleaning agents that contain
alcohol or solvents.
nium care product (-
000 096 319 D -).
Wheels:
Remove dirt and gritting salt deposits with plenty of water.
Alloy wheels: treat dirty aluminium wheels with Volkswagen Genuine wheel rim cleaner (-
000 096 304 -). Volkswagen recommends treating the wheel rims with Volkswagen Genuine hard
wax (- 000 096 317 -) every three months.
-up pen. Go to a qualified
workshop if necessary.
- 000 096 304 -).
Door lock cylinders:

The Volkswagen dealership cannot be held liable for any damage caused by technical modifications
and/or work performed incorrectly.
The Volkswagen dealership is not responsible for damage caused by technical modifications and/or
work performed incorrectly. Such damage is not covered by the Volkswagen guarantee.
Volkswagen recommends that all repairs and technical modifications be performed by an authorised
Volkswagen workshop using Volkswagen Genuine Parts®.
Volkswagen repair information
Volkswagen service information and official Volkswagen repair information can be purchased for a
fee.
Customers in Europe, Asia, Australia, Africa, Central and South America: please contact a
Volkswagen dealership or qualified workshop or register with the online portal erWin (electronic
repair and workshop information):
https://erwin.volkswagen.de
erWin is available in numerous languages.
Vehicles with special body equipment or add-on parts
The manufacturers of body equipment and add-on parts must ensure that the body equipment and
add-on parts (conversions) adhere to the applicable environmental laws and regulations, particularly
the EU directive 2000/53/EC concerning end-of-life vehicles and EU directive 2003/11/EC concerning
the restrictions on the marketing and use of certain dangerous substances and preparations.
The vehicle owner should keep all assembly documentation for these conversions, and pass it on to
the disassembly company upon vehicle handover if the vehicle is scrapped. This is designed to
facilitate environmentally friendly disposal for all vehicles, including converted vehicles.
Windscreen repairs
To function properly, some items of equipment require an electrical or electronic module, which is
located on the inside of the windscreen near the interior mirror. If the windscreen has been
damaged in the viewing field of the electrical or electronic module, e.g. by stone impact, the
windscreen must be replaced. Repairing the crack can lead to malfunctions or faults in the
equipment.
After changing the windscreen, the camera and sensors must be set up and calibrated by a qualified
workshop.
Impairment or damage to sensors and cameras
Incorrectly performed repairs, structural changes to the vehicle, e.g. lowering the suspension,
retrofitted add-on parts or changes to the trim can lead to sensors and cameras being displaced or
damaged. This can also be caused by collisions, e.g. when parking, or also even by minor damage,
e.g. stone impacts on the windscreen.
Failure to observe this point may impair important functions (driver assist systems) and damage the
vehicle.

The area in front of and around the sensors and cameras must not be covered by stickers, additional
headlights, trim frames for number plates or similar.
Repairs and structural modifications should therefore be carried out only by a qualified workshop.
Volkswagen recommends using a Volkswagen dealership for this purpose.
-ups in the area around the sensors may impair the function of the
system in question.
vehicle only with the original Volkswagen badge.
Engine and transmission guard
An engine and transmission guard can reduce the risk of damage to the vehicle's underbody and
sump, for example when driving over kerbs, drive entrances or unsurfaced roads.
Volkswagen recommends that you have this equipment retrofitted by your Volkswagen dealership.

WARNING
Incorrectly performed repairs and modifications can cause malfunctions and damage to the vehicle
and impair the effectiveness of the driver assist systems. This can result in accidents and severe
injuries.


WARNING
Unsuitable spare parts and accessories, incorrectly carried out work, modifications and repairs can
lead to damage to the vehicle and cause accidents and serious injuries.
Volkswagen Genuine Parts®. These parts and accessories have been specially tested by Volkswagen
for suitability, reliability and safety.
workshops have the necessary tools, diagnostic equipment, repair information and qualified
personnel.
cle that differ in their design or characteristics from the factory-fitted
parts.
since these objects can cause serious or fatal injuries if the airbags are triggered.
type.
Repairs and faults in the airbag system

Repairs and technical modifications must always be carried out according to Volkswagen
specifications⇒ .
Modifications and repairs to the front bumper, doors, front seats, headliner or the bodywork should
be carried out only by a qualified workshop. Airbag system components and sensors might be fitted
on these vehicle components.
If you work on the airbag system or remove and install parts of the system when performing other
repair work, parts of the airbag system may be damaged. The consequence may be that, in the event
of an accident, the airbag inflates incorrectly or does not inflate at all.
Regulations must be observed to ensure that the effectiveness of the airbags is not reduced and that
removed parts do not cause any injuries or environmental pollution. Qualified workshops are
familiar with these regulations.
Any modifications to the vehicle's suspension could prevent the airbag system from working
properly during a collision. For example, using wheel rim/tyre combinations that have not been
approved by Volkswagen, lowering the suspension or making modifications to the suspension rate
including work on the springs, struts and shock absorbers etc., could change the forces that are
measured by the airbag sensors and sent to the electronic control unit. Some changes to the
suspension could cause the forces measured by the sensors to increase, for example. This can lead
to the airbag system being triggered in collision scenarios where it normally would not be triggered if
modifications to the suspension had not been made. Other modifications can cause the forces
measured by the sensors to decrease, therefore preventing the airbag system from being triggered
when it should have been.

WARNING
Incorrect repairs and modifications can cause malfunctions and damage to the vehicle and impair
the effectiveness of the airbag system. This can result in accidents and serious or even fatal injuries.


en taken from end-of-life
vehicles in your vehicle.

WARNING
Modifications to the vehicle's suspension, including the use of unsuitable tyre/rim combinations, can
cause the airbag system to function differently and increase the risk of serious or fatal injuries in the
event of an accident.
the original factory-fitted components.
en.
Mobile reception in the vehicle

Radio
equipm
ent
installe
d in the
vehicle
Manufacturers'
addresses
(auxilia
ry
heater)
Weberstrasse 20
02763 Zittau
GERMANY
Eberspächer
Climate Control
Systems
GmbH & Co. KG
Eberspächerstrasse
24
73730 Esslingen
GERMANY
Auxiliar
y
heater
Webasto
Thermo & Comfort
SE
Friedrichshafener S
trasse 9
82205 Gilching
GERMANY
Tyre
pressur
e
sensors
Huf Hülsbeck &
Fürst GmbH &
Co. KG
Steeger Strasse 17
42551 Velbert
GERMANY
Mapping table
The mapping table is designed to help you link the device name used in a declaration of conformity
with the vehicle equipment and terms contained in the vehicle wallet.
Vehicle
equipm
ent
Device name
according to
declaration of
conformity
Vehicle
key
FKS0
9
FS09 FS12
A

Vehicle
equipm
ent
Device name
according to
declaration of
conformity
cluste
r 1
nt
clust
er 2
nt
clust
er 3
EZS-
VW-
Touar
eg
2017-02-EU-
LF_IC_IM
Immobiliser
integrated in
dashboard module
instrument cluster
Tyre
pressur
e
sensors
TSSR
E4Dg
TSSS
G4G5

Blueto
oth
ALPS
UGZZ
F-
102B
ALPS
UGZZ
F-
202B
HT-5
MIB2
Entry
MIB2
Mai
n-
Unit

MIB
Global Entry
/Standard

WLAN
hotspot
HT-5 MIB2
Mai
n-
Unit

MIB
Global Entry
/Standard

Vehicle
equipm
ent
Device name
according to
declaration of
conformity
Mobile
phone
interfac
e
HT-5
Connec
tion to
the
externa
l aerial
LTE-
MBC-
EU
UMT
S/GS
M-
MMC

Garage
door
opener
ADHL
5D
EHL2
EHL2 (Euro
HomeLink 2)

Keyless
Access
Kessy
MQB-
A
Kessy
MQB
-A SG
Kessy
MQB
-B B
Kessy
MQB-
B H
Kessy
MQB
-B SG
Kessy
PPQ
35
SG
Kessy
PQ35
Kessy
PQ35
GP
MQB
-A
MQB-
B B
MQB
-B H
PQ35
Kessy
PQ35
GP
PKET
OUA
(868
MHz)
RKET
OUA
Radar
sensors
for
assist
system
ARS4-
B
BSD
3.0
LCA 2
.0A
LRR3 LRR3
Mast
LRR4

Radio
equipment
a)
Frequ
ency
band
Max. tr
ansmit
power
Applies to:
Sharan.
868.7
–
869.2
MHz
(869.0
MHz)
23.5
mW, /
13.7
dBm
e.r.p.
Applies to:
MQB 37,
MQB 48⇒ Key
to models .
868.0
–
868.6
MHz
(868.5
25
MHz)
10 mW
ERP
Applies to:
Touareg.
Tyre
pressure
sensors
433.9
2 MHz
10 mW
Applies to: Volkswagen
models with
Tyre Pressure
Monitoring
System.
Instrument
cluster
125
kHz
40
dBμA/
m
Applies to: All Volkswagen
models.
Electronic 125 3.728