brake VOLVO 850 1996 Owner's Manual

1996 Volvo 850
can cause three-way catalytic converter or exhaust system overheating.
l Remember that tampering or unauthorized modification to the engine or th\
e vehicle may be illegal
and can cause three-way catalytic converter or exhaust system overheatin\
g. This includes:
- Altering fuel injection settings or components.
- Adjusting distributor ignition timing beyond specified limits.
- Altering emission system components or location or removing components\

- Repeated use of leaded fuel.

NOTE: Unleaded fuel is required for cars with three-way catalytic conver\
ters. A label on the instrument
panel and inside fuel tank filler door will remind owners and filling st\
ation attendants of this
requirement.

Important! It is unlawful to dispense leaded fuel into any vehicle label\
ed "unleaded gasoline only".
pg. 4:16 Brake system


Anti-lock Brake System (ABS)

If the warning lamp lights up there is a malfunction of the ABS system (\
the standard braking system will
however function) and the vehicle should be driven to a Volvo retailer \
for inspection. The Anti-lock
Braking System (ABS) helps to improve vehicle control (stopping and s\
teering) during severe braking
conditions by limiting brake lock-up. When the system "senses" impending\
lock-up, braking pressure is
automatically modulated in order to help prevent lockup, which could lea\
d to a skid.
The system performs a self-diagnostic test when the vehicle first reache\
s a speed of approximately 12
mph (20 km/h). The brake pedal will pulsate several times and a sound \
may be audible from the ABS
control module. This is normal.
To obtain optimal effect from the ABS system, constant pressure should b\
e kept on the brake pedal
while the system is modulating the brakes. Do not pump the brake pedal. \

The switching of the ABS modulator will be audible and the brake pedal w\
ill pulsate at this time. Please
be aware that ABS does not increase the absolute braking potential of th\
e vehicle. While control will be
enhanced, ABS will not shorten stopping distances on slippery surfaces. \

file:///K|/ownersdocs/1996/1996_850/96850_412.htm (5 of 10)12/30/2006 \
9:59:35 AMClassic Cars & Cycles www.ClassicCycles.org

1996 Volvo 850


Brake circuit malfunction

If one of the brake circuits should malfunction, the red warning light w\
ill come on, the pedal stroke
increases slightly, the pedal feels softer and extra pressure is require\
d for normal braking. If the light
comes on while driving or braking, stop immediately and check the brake \
fluid level in the reservoir.
WARNING! If the fluid level is below the MIN mark in either section of t\
he reservoir: DO NOT
DRIVE. Tow the car to a Volvo retailer and have the brake system checked\
and repaired.

Moisture on brake discs and brake pads affects braking.

Driving in rain and slush or passing through an automatic car wash can c\
ause water to collect on the
brake discs and pads. This will cause a delay in braking effect when the\
pedal is depressed. To avoid
such a delay when the brakes are needed, depress the pedal occasionally \
when driving through rain,
slush etc. This will remove the water from the brakes. Check that brake \
application feels normal! This
should also be done after washing or starting in very damp weather.

Severe strain on the brake system

The brakes will be subject to severe strain when driving in mountains or\
hilly areas or towing. The speed
is usually low which means that the cooling of the brakes is less effici\
ent than when driving on level
roads. To reduce the strain on the brakes it is advisable not to use the\
brakes excessively. Instead, shift
into a lower gear, position 3 or in some cases, L(automatic transmissio\
n) and let the engine help with the
braking. Do not forget that, if you are towing a trailer, the brakes wil\
l be subjected to greater load than is
normal.

If the brake power-assist does function

The power assist to the brakes functions only when the engine is running\
. When the car is moving
without the engine running, the brake pedal pressure required to stop th\
e car is increased by 3-4 times
and the brake pedal feels stiff.
file:///K|/ownersdocs/1996/1996_850/96850_412.htm (6 of 10)12/30/2006 \
9:59:35 AMClassic Cars & Cycles www.ClassicCycles.org

1996 Volvo 850
pg. 4:17 Trailer towing
When preparing for trailer towing, observe the following:

l Volvo recommends the use of Volvo trailer hitches which are specially de\
signed for the car. For
trailer weights exceeding 2000 lbs. (908 kg), use only a trailer hitch\
offered as a Genuine Volvo
accessory.

NOTE: Models with automatic transmission are equipped with a transmissio\
n oil cooler as standard
equipment. This cooler helps prevent overheating of the transmission dur\
ing times of increased load, as
when towing a trailer.

l Maximum trailer weight recommended by Volvo is:
Trailers without brakes : 1100 lbs (500kg)
Trailers with brakes: 2" (50 mm) ball - 3300 lbs (1500 kg), 1 7/8" (\
47 mm) ball - 2000 lbs (908 kg).

Observe the legal requirements of the state/province in which the vehicl\
es are registered. All Volvo
models are equipped with energy-absorbing shock-mounted bumpers. Trailer\
hitch installation should
not interfere with the proper operation of this bumper system.

Trailer towing does not normally present any particular problems, but ta\
ke into consideration:
l Increase tire pressure to recommended full. See section "Wheels and tire\
s".
l Recommended hitch tongue load is 110 (50 kgs) for trailer weights belo\
w 2,650 lbs (1,200 kgs) and
165 lbs (75 kgs) for trailer weights above 2,650 lbs (1,200 kgs). Fo\
r trailer weights between 2,650-3,300
lbs (1,200-1,500 kgs) a top speed of 50 mph (80 km/h) should never b\
e exceeded.
l Engine and transmission are subject to increased loads. Therefore, engin\
e coolant temperature should
be closely watched when driving in hot climates or hilly terrain. Use lo\
wer gear and turn off air
conditioner if temperature gauge pointer enters the red range.
l Avoid overload and other abusive operation.
l Hauling a trailer affects handling, durability, and economy.
l It is necessary to balance trailer brakes with the towing vehicle brakes\
to provide a safe stop (check
and observe State/Local regulations).
l Do not connect the trailer's brake system directly to the vehicle's brak\
e system.
l More frequent vehicle maintenance is required.
l Remove the ball and drawbar assembly when the hitch is not being used.
l Volvo recommends the use of synthetic engine oil when towing a trailer o\
ver long distances or in
file:///K|/ownersdocs/1996/1996_850/96850_412.htm (7 of 10)12/30/2006 \
9:59:35 AMClassic Cars & Cycles www.ClassicCycles.org

1996 Volvo 850
mountainous areas.

NOTE: Refer to section "Automatic transmission" for additional trailer h\
auling tips.
WARNING!
l Bumper-attached trailer hitches must not be used on Volvos, nor should s\
afety chains be attached to
the bumper.
l Trailer hitches attaching to the vehicle rear axle must not be used.
l Never connect a trailer's hydraulic brake system directly to the vehicle\
brake system, nor a trailer's
lighting system directly to the vehicle lighting system. Consult your ne\
arest authorized Volvo retailer
for correct installation.
pg. 4:18 Winter driving
Cold weather precautions

l If you wish to check your car before the approach of cold weather, the f\
ollowing advice is worth
noting:
l Make sure that the engine coolant contains at least 50 percent antifreez\
e: that is, 3.7 qts. (3.5 liters)
Volvo Genuine Coolant/Antifreeze. This gives protection against freezing\
down to -31°F (-35°C). See
section "Coolant". The use of "recycled" antifreeze is not approved by V\
olvo. Different types of
antifreeze may not be mixed.
l Try to keep the fuel tank well filled - this prevents the formation of c\
ondensation in the tank. In
addition in extremely cold weather conditions it is worthwhile to add fu\
el line de-icer before refueling.
l The viscosity of the engine oil is important. Oil with low viscosity (t\
hinner oil) improves cold-
weather starting as well as decreasing fuel consumption while the engine\
is warming up. For winter use,
5W-30 oil, particularly the synthetic type, is recommended. Be sure to u\
se good quality oil but do not
use this cold-weather oil for hard driving or in warm weather. See secti\
on "Engine oil" for more
information.
l The load placed on the battery is greater during the winter since the he\
ater, windshield wipers,
lighting etc. are used more often. Moreover, the capacity of the battery\
decreases as the temperature
drops. In very cold weather, a poorly charged battery can freeze and be \
damaged. It is therefore
advisable to check the state of charge more frequently and spray an anti\
-rust oil on the battery posts.
l Volvo recommends the use of snow tires on all four wheels for winter dri\
ving - see section "Wheels
and tires".
l To prevent the washer reservoir from freezing, add washer solvents conta\
ining antifreeze (see page
file:///K|/ownersdocs/1996/1996_850/96850_412.htm (8 of 10)12/30/2006 \
9:59:35 AMClassic Cars & Cycles www.ClassicCycles.org

1996 Volvo 850
l Check condition of drive belts.
l Check state of charge of battery.
l Examine tires carefully (the spare tire as well), and replace those th\
at are worn. Check tire pressures.
l The brakes, front wheel alignment, and steering gear should be checked b\
y your Volvo retailer only.
l Check all lights, including high beams.
l Reflective warning triangles are legal requirement in some countries.
l Have a word with your Volvo retailer concerning engine adjustments if yo\
u intend to drive in
countries where it may be difficult to obtain correct fuel.
l Consider your destination. If you will be driving through an area where \
snow or ice are likely to
occur, consider snow tires.




Contents | Top of Page
file:///K|/ownersdocs/1996/1996_850/96850_412.htm (10 of 10)12/30/2006\
9:59:35 AMClassic Cars & Cycles www.ClassicCycles.org

1996 Volvo 850
pg. 5:3 Wheels and tires
Snow chains

Snow tire chains can be used on your Volvo with the following restrictio\
ns:
l Snow chains should be installed on your front wheels only.
l Snow chains may be mounted on tire dimension 185/65R15 and 195/60R15. Ti\
re dimension
205/55R15 and 205/50R16 require a special type of snow chain. Consult yo\
ur Volvo retailer. Snow
chains may not be used on 205/55R16
If accessory, aftermarket or "custom" tires and wheels are installed and\
are of a size different than the
original tires and wheels, chains in some cases CANNOT be used. Snow cha\
ins cannot be used on those
turbo models fitted with all-season tires 205/55 R16 or 205/45 R17. Mode\
ls equipped with 205/55 R15
or 205/50 R16 need specially designed snow chains. Sufficient clearances\
between chains and brakes,
suspension and body components must be maintained.
l Some strap-on type chains will interfere with brake components and there\
fore CANNOT be used.
CAUTION:
l Check local regulations regarding the use of snow chains before installi\
ng.
l Always follow the chains manufacturer's installation instructions carefu\
lly. Install chains as tightly
as possible and re-tighten periodically.
l Never exceed the chain manufacture's specified maximum speed limit. (Un\
der no circumstances
should that limit be higher than 30 mph (45 km/h).
l Avoid bumps, holes or sharp turns when driving with snow chains.
l The handling of the vehicle can be adversely affected when driving with \
chains. Avoid fast or sharp
turns as well as locked wheel braking.

Snow tires, studded tires *

Tires for winter use:
Owners who live in or regularly commute through areas with sustained per\
iods of snow or icy driving
conditions are strongly advised to fit suitable winter tires to help ret\
ain the highest degree of traction.
It is important to install winter tires on all four wheels to help retai\
n traction during cornering, braking
and accelerating. Failure to do so could reduce traction to an unsafe le\
vel or adversely affect handling.
Do not mix tires of different design as this could also negatively affec\
t overall tire road grip. Volvo
recommends 185/65 R15 winter tires on 15" wheels on all 850 models inclu\
ding models equipped with
file:///K|/ownersdocs/1996/1996_850/96850_501.htm (3 of 5)12/30/2006 9\
:59:37 AMClassic Cars & Cycles www.ClassicCycles.org

1996 Volvo 850
Loosen wheel bolts Insert flat end of lug wrench and turn


Pull straight out

Changing a wheel

The spare wheel is located under the carpet on the trunk floor. The jack\
and crank are secured in the
wheel recess.
l Engage the parking brake.
l Put the gear selector in (P)ark (automatic) or in Reverse (manual)\
.
l Remove the wheel cap (where applicable) using the lug wrench in the to\
ol kit.
l With the car still on the ground, use the lug wrench to loosen the wheel\
bolts 1/2 - 1 turn. Turn the
bolts counterclockwise to loosen.
l Fold out the crank handle on the jack by pressing the nob on the handle \
downward. To attach the jack,
refer to the illustration on the following page.

NOTE:
To avoid excessive wear and the necessity of rebalancing, mark and reins\
tall wheels in same location
and position as before removal. To lessen the chance of imbalance, each \
wheel hub is equipped with a
guide stud to ensure that a removed wheel can be reinstalled in its orig\
inal position (as when changing
over to winter tires/wheels).

*The guide stud in not visible from the outside of the wheel on turbo mo\
dels.
file:///K|/ownersdocs/1996/1996_850/96850_601.htm (2 of 5)12/30/2006 9\
:59:39 AMClassic Cars & Cycles www.ClassicCycles.org

1996 Volvo 850
WARNING!
l The jack attachment must engage the bar in the jack attachment (A). Th\
e car's weight must not rest
on the jack's attachment (B).
l Be sure the jack is on a firm, level, non-slippery surface.
l Never allow any part of your body to be extended under a car supported b\
y a jack.
l Use the jack intended for the car when replacing a wheel. For any other \
job, use stands to support
the end of the car being worked on.
l Apply the parking brake, select position P (automatic transmission) or\
Reverse gear (manual
transmission).
l Block the wheels standing on the ground. Use rigid wooden blocks or larg\
e stones.
l The jack should be kept well-greased.

Installing the wheel

Clean the contact surfaces on the wheel and hub. Lift the wheel and plac\
e it on the hub. Make sure that
you align the wheel with the guide stud on the wheel hub prior to instal\
lation. Install the wheel bolts
cross-wise (see illustration) and tighten by turning lightly clockwise\
. Lower the vehicle to the ground
and alternately tighten the bolts to 81 ft. lbs. (110 NM). Install the\
wheel cap (where applicable).
CAUTION: Correct tightening torque on wheel bolts must be observed. The \
wheel bolts should never
be greased or lubricated. The extended, chromed wheel bolts must not be \
used with steel rims, as they
make is impossible to fit the hub caps.


Correct tightening order for wheel bolts
pg. 6:4 Spare tire
file:///K|/ownersdocs/1996/1996_850/96850_601.htm (4 of 5)12/30/2006 9\
:59:39 AMClassic Cars & Cycles www.ClassicCycles.org

1996 Volvo 850

Lateral headlight adjustment should only be carried out by an authorized\
Volvo retailer. The lateral
adjustment scale (B) should be preset to "0". pg. 6:7 Replacing bulbs, Sedans

Lamp location- right side, A- covers, B- bulb holder

Tail light bulbs (sedans)

1. Tail light
2. Direction indicator
3. Brake light
4. Tail light
5. Back-up light
6. Rear fog light (left side only)

file:///K|/ownersdocs/1996/1996_850/96850_605.htm (3 of 13)12/30/2006 \
9:59:43 AMClassic Cars & Cycles www.ClassicCycles.org

1996 Volvo 850
2. Brake light
3. Tail light
4. Back-up light
5. Tail light / Rear fog light (left side only)

All the bulbs in the tail light unit are replaced from inside the cargo \
space as follows:
l Turn the ignition key to position 0 and switch off the lights.
l Remove the upper panel of the tail light unit by using a screwdriver and\
/or the lower panel by first
removing the side floor cover and then the panel.
l Press in the plastic catches (A or B) and take out the bulb holder.
l Remove the speaker (optional) from the upper section of the tail light\
unit.
l Leave the connector and cables connected to the bulb holder.
l Remove the bulb by pressing it inwards and turning it slightly counter-c\
lockwise.
l Insert a new bulb into the bulb holder and reinstall the holder in the t\
ail light assembly.
l Check that the bulb works. Reinstall the cover.
pg. 6:9 Replacing bulbs Depress the catches (sedans)

Press sides and pull out/down (wagons)

file:///K|/ownersdocs/1996/1996_850/96850_605.htm (6 of 13)12/30/2006 \
9:59:43 AMClassic Cars & Cycles www.ClassicCycles.org