wheel torque YAMAHA DT125R 2002 Owners Manual

6-28
PERIODIC MAINTENANCE AND MINOR REPAIR
6
NOTE:
Make sure that both adjusting plates
are in the same position for proper
wheel alignment.
EC000096
cCImproper drive chain slack will
overload the engine as well as
other vital parts of the motorcycle
and can lead to chain slippage or
breakage. To prevent this from
occurring, keep the drive chain
slack within the specified limits.3. Tighten the axle nut to the speci-
fied torque.2. Wipe the drive chain dry.
3. Thoroughly lubricate the drive
chain with a special O-ring chain
lubricant.
ECA00052
cCDo not use engine oil or any other
lubricants for the drive chain, as
they may contain substances that
could damage the O-rings.
EAU03006
Lubricating the drive chainThe drive chain must be cleaned and
lubricated at the intervals specified in
the periodic maintenance and lubrica-
tion chart, otherwise it will quickly
wear out, especially when riding in
dusty or wet areas. Service the drive
chain as follows.
EC000097
cCThe drive chain must be lubricated
after washing the motorcycle or
riding in the rain.1. Clean the drive chain with
kerosene and a small soft brush.
ECA00053
cCTo prevent damaging the O-rings,
do not clean the drive chain with
steam cleaners, high-pressure
washers or inappropriate solvents.
Tightening torque:
Axle nut:
90 Nm (9.0 m0kgf)
3MB-9-E8 6/13/01 10:55 AM Page 65

6-41
PERIODIC MAINTENANCE AND MINOR REPAIR
67. After tightening the holder nuts,
while applying the front brake,
push down on the handlebars
several times to check if the front
fork compress and rebounds
smoothly.
8. Connect the speedometer cable.
6. Tighten the axle holder nuts to
the specified tightening torque.
Tighten the upper nuts first and
then lower ones. When tightened
in this sequence, there should be
a gap formed at the bottom of
the axle holder.
NOTE:
Make sure that there is enough
space between the brake pads
before inserting the brake disc and
that the slot in the speedometer gear
unit fits over the retainer on the fork
leg.3. Install the wheel axle.
4. Lower the front wheel so that it is
on the ground.
5. Tighten the wheel axle to the
specified torque.
1
1. Retainer
Tightening torque:
Wheel axle:
58 Nm (5.8 m0kgf)Tightening torque:
Axle holder nut:
10 Nm (1.0 m0kgf)
a
a. Gap
3MB-9-E8 6/13/01 10:55 AM Page 78

6-43
PERIODIC MAINTENANCE AND MINOR REPAIR
6
EAU03087
TroubleshootingAlthough Yamaha motorcycles
receive a thorough inspection before
shipment from the factory, trouble
may occur during operation. Any
problem in the fuel, compression, or
ignition systems, for example, can
cause poor starting and loss of
power.
The following troubleshooting charts
represent quick and easy procedures
for checking these vital systems your-
self. However, should your motorcy-
cle require any repair, take it to a
Yamaha dealer, whose skilled techni-
cians have the necessary tools,
experience, and know-how to service
the motorcycle properly.
Use only genuine Yamaha replace-
ment parts. Imitation parts may look
like Yamaha parts, but they are often
inferior, have a shorter service life
and can lead to expensive repair
bills.
EAU01806
To install the rear wheel
1. Install the drive chain onto the
rear sprocket, and then insert the
wheel axle from the left side.NOTE:
Make sure that there is enough
space between the brake pads
before inserting the brake disc
between the pads.2. Install the swingarm end bolts,
and then lower the rear wheel so
that it is on the ground.
3. Adjust the drive chain slack.
(See page 6-27 for drive chain
slack adjustment procedures.)
4. Tighten the axle nut and
swingarm end bolts to the speci-
fied torques.
Tightening torques:
Axle nut:
90 Nm (9.0 m0kgf)
Swingarm end bolts:
3 Nm (0.3 m0kgf)
3MB-9-E8 6/13/01 10:55 AM Page 80