wheel YAMAHA DT125R 2005 User Guide

Recommended lubricant:
Lithium-soap-based grease (all-pur-
pose grease)
EAU23271
Checking the front fork
The condition and operation of the
front fork must be checked as follows
at the intervals specified in the perio-
dic maintenance and lubrication
chart.
To check the condition
EWA10750
s s
WARNING
Securely support the motorcycle so
that there is no danger of it falling
over.
Check the inner tubes for scratches,
damage and excessive oil leakage.To check the operation
1. Place the motorcycle on a level
surface and hold it in an upright
position.
2. While applying the front brake,
push down hard on the handle-
bars several times to check if the
front fork compresses and
rebounds smoothly.ECA10590
CAUTION
If any damage is found or the front
fork does not operate smoothly,
have a Yamaha dealer check or
repair it.
EAU23280
Checking the steering
Worn or loose steering bearings may
cause danger. Therefore, the opera-
tion of the steering must be checked
as follows at the intervals specified in
the periodic maintenance and lubrica-
tion chart.
1. Place a stand under the engine to
raise the front wheel off the
ground.
EWA10750
s s
WARNING
Securely support the motorcycle so
that there is no danger of it falling
over.
6
PERIODIC MAINTENANCE AND MINOR REPAIR
6-22
1D0-F8199-E2.qxd 20/9/04 11:32 Página 53

2. Hold the lower ends of the front
fork legs and try to move them
forward and backward. If any free
play can be felt, have a Yamaha
dealer check or repair the stee-
ring.
EAU23290
Checking the wheel bearings
The front and rear wheel bearings
must be checked at the intervals spe-
cified in the periodic maintenance and
lubrication chart. If there is play in the
wheel hub or if the wheel does not
turn smoothly, have a Yamaha dealer
check the wheel bearings.
EAU23380
Battery
1. Battery
2. Battery ventilation pipe
The battery is located behind panel D.
(See page 6-6.)
This model is equipped with a sealed-
type (MF) battery, which does not
require any maintenance. There is no
need to check the electrolyte or to
add distilled water.
ECA10620
CAUTION
Never attempt to remove the bat-
tery cell seals, as this would per-
manently damage the battery.
EWA10760
s s
WARNING
Electrolyte is poisonous and
dangerous since it contains
sulfuric acid, which causes
severe burns. Avoid any con-
tact with skin, eyes or clothing
and always shield your eyes
when working near batteries.
In case of contact, administer
the following FIRST AID.
• EXTERNAL: Flush with plenty
of water.
• INTERNAL: Drink large quan-
tities of water or milk and
immediately call a physician.• EYES: Flush with water for 15
minutes and seek prompt
medical attention.
• Batteries produce explosive
hydrogen gas. Therefore,
keep sparks, flames, cigaret-
tes, etc., away from the bat-
tery and provide sufficient
ventilation when charging it
in an enclosed space.
KEEP THIS AND ALL BATTE-
RIES OUT OF THE REACH OF
CHILDREN.
To charge the battery
Have a Yamaha dealer charge the
battery as soon as possible if it seems
to have discharged. Keep in mind that
the battery tends to discharge more
quickly if the vehicle is equipped with
optional electrical accessories.
To store the battery
1. If the vehicle will not be used for
more than one month, remove
the battery, fully charge it, and
then place it in a cool, dry place.
6
PERIODIC MAINTENANCE AND MINOR REPAIR
6-23
2
1
1D0-F8199-E2.qxd 20/9/04 11:32 Página 54

ECA10680
CAUTION
Do not overtighten the screws,
otherwise the lens may break.
EAU24201
Replacing a turn signal light
bulb
1. Screw
2. Lens
3. Bulb
1. Remove the turn signal light lens
by removing the screw.
2. Remove the defective bulb by
pushing it in and turning it coun-
terclockwise.
3. Insert a new bulb into the socket,
push it in, and then turn it clock-
wise until it stops.4. Install the lens by installing the
screw.
ECA11190
CAUTION
Do not overtighten the screw,
otherwise the lens may break.
EAU24350
Supporting the motorcycle
Since this model is not equipped with
a centerstand, follow these precau-
tions when removing the front and
rear wheel or performing other main-
tenance requiring the motorcycle to
stand upright. Check that the
motorcycle is in a stable and level
position before starting any mainte-
nance. A strong wooden box can be
placed under the engine for added
stability.
To service the front wheel
1. Stabilize the rear of the motorcy-
cle by using a motorcycle stand
or, if an additional motorcycle
stand is not available, by placing
a jack under the frame in front of
the rear wheel.2. Raise the front wheel off the
ground by using a motorcycle
stand.
To service the rear wheel
Raise the rear wheel off the ground by
using a motorcycle stand or, if a
motorcycle stand is not available, by
placing a jack either under each side
of the frame in front of the rear wheel
or under each side of the swingarm.
EAU24360
Front wheel
EAU24640
To remove the front wheel
1. Speedometer cable
2. Axle retainer nut (x4)
3. Wheel axle
6
PERIODIC MAINTENANCE AND MINOR REPAIR
6-26
1
3
2
31
2
1D0-F8199-E2.qxd 20/9/04 11:32 Página 57

EWA10820
s s
WARNING
It is advisable to have a Yama-
ha dealer service the wheel.
Securely support the motorcy-
cle so that there is no danger of
it falling over.
1. Disconnect the speedometer
cable from the front wheel.
2. Loosen the wheel axle holder
nuts, then the wheel axle.
3. Lift the front wheel off the ground
according to the procedure on
page 6-26.
4. Pull the wheel axle out, and then
remove the wheel.
ECA11070
CAUTION
Do not apply the brake after the
wheel has been removed together
with the brake disc, otherwise the
brake pads will be forced shut.
EAU24950
To install the front wheel
1. Install the speedometer gear unit
into the wheel hub so that the
projections mesh with the slots.
2. Lift the wheel up between the
fork legs.
NOTE:
Make sure that there is enough space
between the brake pads before inser-
ting the brake disc and that the slot in
the speedometer gear unit fits over
the retainer on the fork leg.
3. Insert the wheel axle.
4. Lower the front wheel so that it is
on the ground.
5. Tighten the wheel axle to the
specified torque.
Tightening torque:
Wheel axle:
55 Nm (5,5 m•kgf)
6. Tighten the axle holder nuts to
the specified tightening torque. Tigh-
ten the upper nuts first and then lower
ones. When tightened in this sequen-
ce, there should be a gap formed at
the bottom of the axle holder.
Tightening torque:
Axle holder nut:
10 Nm (1,0 m•kgf)
6
PERIODIC MAINTENANCE AND MINOR REPAIR
6-27
1D0-F8199-E2.qxd 20/9/04 11:32 Página 58

1. Gap
7. After tightening the axle holder
nuts, push down hard on the
handlebars several times while
applying the front brake to check
if the front fork compresses and
rebounds smoothly.
8. Connect the speedometer cable.
EAU25080
Rear wheel
EAU25230
To remove the rear wheel
1. Axle retainer bolt
EWA10820
s s
WARNING
It is advisable to have a Yama-
ha dealer service the wheel.
Securely support the motorcy-
cle so that there is no danger of
it falling over.
1. Loosen the axle nut.
2. Lift the rear wheel off the ground
according to the procedure on
page 6-26.
1. Axle nut
2. Chain tensioner
3. Remove the swingarm end bolts.
4. Turn the drive chain adjusting
plate on each side of the swin-
garm fully in direction (a).
5. Push the wheel forward, and then
remove the drive chain from the
rear sprocket.
NOTE:
The drive chain does not need to be
disassembled in order to remove and
install the rear wheel.
6. Pull the wheel axle out from the
left-hand side, and then remove
the wheel by pulling it back.
6
PERIODIC MAINTENANCE AND MINOR REPAIR
6-28
112
1
1D0-F8199-E2.qxd 20/9/04 11:32 Página 59

ECA11070
CAUTION
Do not apply the brake after the
wheel has been removed together
with the brake disc, otherwise the
brake pads will be forced shut.
EAU25530
To install the rear wheel
1. Install the drive chain onto the
rear sprocket, and then insert the
wheel axle from the left-hand
side.
NOTE:
Make sure that there is enough space
between the brake pads before inser-
ting the brake disc between the brake
pads.
2. Install the drive chain adjusting
plates.
NOTE:
Make sure that the drive chain adjus-
ting plates are installed with the pun-
ched side facing to the outside.
3. Install the swingarm end bolts.4. Adjust the drive chain slack. (See
page 6-19.)
5. Tighten the axle nut and the
swingarm end bolts to the speci-
fied torques, and then install the
cotter pin.
EWA10700
s s
WARNING
Always use a new cotter pin for the
axle nut.
Tightening torque:
Axle nut:
90 Nm (9,0 m•kgf)
Swingarm end bolt:
3 Nm (0,3 m•kgf)
EAU25850
Troubleshooting
Although Yamaha motorcycles recei-
ve a thorough inspection before ship-
ment from the factory, trouble may
occur during operation. Any problem
in the fuel, compression, or ignition
systems, for example, can cause poor
starting and loss of power.The following troubleshooting chart
represents a quick and easy procedu-
re for checking these vital systems
yourself. However, should your
motorcycle require any repair, take it
to a Yamaha dealer, whose skilled
technicians have the necessary tools,
experience, and know-how to service
the motorcycle properly.
Use only genuine Yamaha replace-
ment parts. Imitation parts may look
like Yamaha parts, but they are often
inferior, have a shorter service life and
can lead to expensive repair bills.
6
PERIODIC MAINTENANCE AND MINOR REPAIR
6-29
1D0-F8199-E2.qxd 20/9/04 11:32 Página 60

EAU26000
Care
While the open design of a motorcy-
cle reveals the attractiveness of the
technology, it also makes it more vul-
nerable. Rust and corrosion can
develop even if high-quality compo-
nents are used. A rusty exhaust pipe
may go unnoticed on a car, however,
it detracts from the overall appearan-
ce of a motorcycle. Frequent and pro-
per care does not only comply with
the terms of the warranty, but it will
also keep your motorcycle looking
good, extend its life and optimize its
performance.
Before cleaning
1. Cover the muffler outlet with a
plastic bag after the engine has
cooled down.
2. Make sure that all caps and
covers as well as all electrical
couplers and connectors, inclu-
ding the spark plug cap, are
tightly installed.3. Remove extremely stubborn dirt,
like oil burnt onto the crankcase,
with a degreasing agent and a
brush, but never apply such pro-
ducts onto seals, gaskets, sproc-
kets, the drive chain and wheel
axles. Always rinse the dirt and
degreaser off with water.
Cleaning
ECA10770
CAUTION
Avoid using strong acidic whe-
el cleaners, especially on spo-
ked wheels. If such products
are used on hard-to-remove
dirt, do not leave the cleaner on
the affected area any longer
than instructed. Also, tho-
roughly rinse the area off with
water, immediately dry it, and
then apply a corrosion protec-
tion spray.
Improper cleaning can damage
windshields, cowlings, panels
and other plastic parts. Use
only a soft, clean cloth or spon-
ge with mild detergent and
water to clean plastic.
Do not use any harsh chemical
products on plastic parts. Be
sure to avoid using cloths or
sponges which have been in
contact with strong or abrasive
cleaning products, solvent or
thinner, fuel (gasoline), rust
removers or inhibitors, brake
fluid, antifreeze or electrolyte.
Do not use high-pressure was-
hers or steam-jet cleaners sin-
ce they cause water seepage
and deterioration in the follo-
wing areas: seals (of wheel and
swingarm bearings, fork and
brakes), electric components
(couplers, connectors, instru-
ments, switches and lights),
breather hoses and vents.
For motorcycles equipped with
a windshield: Do not use strong
cleaners or hard sponges as
they will cause dulling or scrat-
ching. Some cleaning com-
pounds for plastic may leave
scratches on the windshield.
Test the product on a small hid-
den part of the windshield to
make sure that it does not lea-
7
MOTORCYCLE CARE AND STORAGE
7-1
1D0-F8199-E2.qxd 20/9/04 11:32 Página 63

EWA10950
s s
WARNING
To prevent damage or injury from
sparking, make sure to ground the
spark plug electrodes while turning
the engine over.
6. Lubricate all control cables and
the pivoting points of all levers
and pedals as well as of the
sidestand/centerstand.
7. Check and, if necessary, correct
the tire air pressure, and then lift
the motorcycle so that both of its
wheels are off the ground. Alter-
natively, turn the wheels a little
every month in order to prevent
the tires from becoming degra-
ded in one spot.
8. Cover the muffler outlet with a
plastic bag to prevent moisture
from entering it.9. Remove the battery and fully
charge it. Store it in a cool, dry
place and charge it once a
month. Do not store the battery in
an excessively cold or warm pla-
ce [less than 0 °C (30 °F) or more
than 30 °C (90 °F)]. For more
information on storing the bat-
tery, see page 6-23.
NOTE:
Make any necessary repairs before
storing the motorcycle.
7
MOTORCYCLE CARE AND STORAGE
7-4
1D0-F8199-E2.qxd 20/9/04 11:32 Página 66

DimensionsOverall length
DT125RE 2210 mm
DT125X 2139 mm
Overall width
795 mm
Overall height
DT125RE 1200 mm
DT125X 1121 mm
Seat height
DT125RE 900 mm
DT125X 886 mm
Wheelbase
DT125RE 1415 mm
DT125X 1396 mm
Ground clearance
DT125RE 300 mm
DT125X 271 mm
Minimum turning radius
DT125RE 2100 mm
DT125X 2016 mm
WeightWith oil and fuel
DT125RE 126.0 kg
DT125X 134.0 kg
EngineEngine type
Liquid cooled 2-stroke
Cylinder arrangement
Forward-inclined single cylinder
Displacement
124.0 cm
3
Bore x stroke
56.0 x 50.7 mmCompression ratio
6.70 :1
Starting system
Electric starter
Lubrication system
Separate lubrication (Yamaha autolube)
Type
YAMALUBE 2-cycle oil or 2-stroke engine
oil (JASO FC g
Engine oil quantityQuantity
1.3 L
Transmission oilType
SAE10W30 type SE motor oil
Oil change quantity
0.75 L
Cooling systemCoolant reservoir capacity (up to the maxi-
mum leve
0.30 L
Radiator capacity (including all routes)
0.92 L
Air filterAir filter element
Wet element
FuelRecommended fuel
Regular unleaded gasoline only
Fuel tank capacity
10.7 L
Fuel reserve amount
1.8 L
CarburetorManufacturer
MIKUNI
Type x quantity
TM28-92 x1
Spark plug(s)Manufacturer/model
NGK/BR8ES
Spark plug gap
0.7-0.8 mm
Clutch type
Wet, multiple-disc
TransmissionPrimary reduction system
Helical gear
Primary reduction ratio
71/22 (3.227)
Secondary reduction system
Chain drive
Secondary reduction ratio
57/16 (3.563)
Transmission type
Constant mesh 6-speed
Operation
Left foot operation
Gear ratio1st
34/12 (2.833)
2nd
30/16 (1.875)
3rd
24/17 (1.412)
4th
24/21 (1.143)
8
SPECIFICATIONS
8-1
1D0-F8199-E2.qxd 20/9/04 11:32 Página 67

5th
22/23 (0.957)
6th
18/22 (0.818)
ChassisFrame type
Semi double cradle
Caster angle
DT125RE 27.00 degree
DT125X 24.50 degree
Trail
DT125RE 107.0 mm
DT125X 73.1 mm
Front tireType
With tube
Size
DT125RE 80/90-21 48P
DT125X 120/70-17 58H
Manufacturer/model
DT125RE MICHELIN/T63
DT125X PIRELLI/Sport Demon
Rear tireType
With tube
Size
DT125RE 110/80-18 58P
DT125X 140/70-17 66H
Manufacturer/model
DT125RE MICHELIN/T63
DT125X PIRELLI/Sport Demon
Maximum load
DT125RE 178 kg
DT125X 180 kg
Tire air pressure (measured on cold
tires)
Loading condition
0-90 kg
Front
DT125RE 150 kPa
DT125X 180 kPa
Rear
DT125RE 175 kPa
DT125X 200 kPa
Loading condition
90-178 kg
Front
DT125RE 175 kPa
DT125X 180 kPa
Rear
200 kPa
Off-road ridingFront
DT125RE 150 kPa
Rear
DT125RE 175 kPa
Front wheelWheel type
Spoke wheel
Rim size
DT125RE 21x1.60
DT125X 17x3.00
Rear wheelWheel type
Spoke wheel
Rim size
DT125RE 18x1.85
DT125X 17x3.50
Front brakeType
Single disc brake
Operation
Right hand operation
Recommended fluid
DOT 4
Rear brakeType
Single disc brake
Operation
Right foot operation
Recommended fluid
DOT 4
Front suspensionType
Telescopic fork
Spring/shock absorber type
Coil spring/oil damper
Wheel travel
DT125RE 270.0 mm
DT125X 200.0 mm
Rear suspensionType
Swingarm (link suspension)
Spring/shock absorber type
Coil spring/gas-oil damper
Wheel travel
DT125RE 260.0 mm
DT125X 230.0 mm
Electrical systemIgnition system
CDI
8
SPECIFICATIONS
8-2
1D0-F8199-E2.qxd 20/9/04 11:32 Página 68