brake YAMAHA TRICITY 2017 Owner's Manual

Periodic maintenance and adjustment
6-21
6
EAU22393
Checking the front and rear
brake pads
The front and rear brake pads must be
checked for wear at the intervals spec-
ified in the periodic maintenance and
lubrication chart.
EAU22432Front brake pads
Each front brake pad is provided with
wear indicator grooves, which allow
you to check the brake pad wear with-
out having to disassemble the brake.
To check the brake pad wear, check
the wear indicator grooves. If a brake
pad has worn to the point that the wear
indicator grooves have almost disap-
peared, have a Yamaha dealer replace
the brake pads as a set.
EAU22461Rear brake pads
Each rear brake pad is provided with a
wear indicator, which allows you to
check the brake pad wear without hav-
ing to disassemble the brake. To check
the brake pad wear, check the position
of the wear indicator while applying the
brake. If a brake pad has worn to the
point that the wear indicator almost
touches the brake disc, have a
Yamaha dealer replace the brake pads
as a set.
1. Brake pad wear indicator groove
1
1
1. Brake pad wear indicator
1
UBR7E0E0.book Page 21 Tuesday, October 25, 2016 2:44 PM

Periodic maintenance and adjustment
6-22
6
EAU40262
Checking the brake fluid level
Before riding, check that the brake fluid
is above the minimum level mark.
Check the brake fluid level with the top
of the reservoir level. Replenish the
brake fluid if necessary.
Front brake
Rear brake
WARNING
EWA16011
Improper maintenance can result in
loss of braking ability. Observe
these precautions:
zInsufficient brake fluid may al-
low air to enter the brake sys-
tem, reducing braking
performance.zClean the filler cap before re-
moving. Use only DOT 4 brake
fluid from a sealed container.
zUse only the specified brake flu-
id; otherwise, the rubber seals
may deteriorate, causing leak-
age.
zRefill with the same type of
brake fluid. Adding a brake fluid
other than DOT 4 may result in a
harmful chemical reaction.
zBe careful that water or dust
does not enter the brake fluid
reservoir when refilling. Water
will significantly lower the boil-
ing point of the fluid and may re-
sult in vapor lock, an
d dirt may
clog the ABS hydraulic unit
valves.
NOTICE
ECA17641
Brake fluid may damage painted
surfaces or plastic parts. Always
clean up spilled fluid immediately.
As the brake pads wear, it is normal for
the brake fluid level to gradually go
down. A low brake fluid level may indi-
cate worn brake pads and/or brake
system leakage; therefore, be sure to
check the brake pads for wear and the
brake system for leakage. If the brake
fluid level goes down suddenly, have a
Yamaha dealer check the cause before
further riding.
1. Minimum level mark
1. Minimum level mark
Specified brake fluid:
DOT 4
1
1
UBR7E0E0.book Page 22 Tuesday, October 25, 2016 2:44 PM

Periodic maintenance and adjustment
6-23
6
EAU22733
Changing the brake fluid
Have a Yamaha dealer change the
brake fluid at the intervals specified in
the periodic maintenance and lubrica-
tion chart. In addition, have the oil seals
of the master cylinders and calipers as
well as the brake hoses replaced at the
intervals listed below or whenever they
are damaged or leaking.
zOil seals: Replace every two
years.
zBrake hoses: Replace every four
years.
EAUU0311
Checking the V-belt
The V-belt must be checked and re-
placed by a Yamaha dealer at the inter-
vals specified in the periodic
maintenance and lubrication chart.
UBR7E0E0.book Page 23 Tuesday, October 25, 2016 2:44 PM

Periodic maintenance and adjustment
6-25
6
EAU23173
Lubricating the front and rear
brake levers
Front brake lever
Rear brake lever
The pivoting points of the front and rear
brake levers must be lubricated at the
intervals specified in the periodic main-
tenance and lubrication chart.
EAU23215
Checking and lubricating the
centerstand and sidestand
The operation of the centerstand and
sidestand should be checked before
each ride, and the pivots and metal-to-
metal contact surfaces should be lubri-
cated if necessary.
WARNING
EWA10742
If the centerstand or sidestand does
not move up and down smoothly,
have a Yamaha dealer check or re-
pair it. Otherwise, the centerstand or
sidestand could contact the ground
and distract the operator, resulting
in a possible loss of control.
Recommended lubricant:
Silicone grease
Recommended lubricant:
Lithium-soap-based grease
UBR7E0E0.book Page 25 Tuesday, October 25, 2016 2:44 PM

Periodic maintenance and adjustment
6-26
6
EAU23273
Checking the front fork
The condition and operation of the
front fork must be checked as follows
at the intervals specified in the periodic
maintenance and lubrication chart.
To check the condition
Check the inner tubes for scratches,
damage and excessive oil leakage.
To check the operation
1. Place the vehicle on a level sur-
face and hold it in an upright posi-
tion. WARNING! To avoid injury,
securely support the vehicle so
there is no danger of it falling
over.
[EWA10752]
2. While applying the front brake,
push down hard on the handle-
bars several times to check if the
front fork compresses and re-
bounds smoothly.
NOTICE
ECA10591
If any damage is found or the front
fork does not operate smoothly,
have a Yamaha dealer check or re-
pair it.
EAU45512
Checking the steering
Worn or loose steering bearings may
cause danger. Therefore, the operation
of the steering must be checked as fol-
lows at the intervals specified in the
periodic maintenance and lubrication
chart.
1. Place the vehicle on the center-
stand. WARNING! To avoid inju-
ry, securely support the vehicle
so there is no danger of it falling
over.
[EWA10752]
2. Hold the lower ends of the front
fork legs and try to move them for-
ward and backward. If any free
play can be felt, have a Yamaha
dealer check or repair the steer-
ing.
UBR7E0E0.book Page 26 Tuesday, October 25, 2016 2:44 PM

Periodic maintenance and adjustment
6-32
6
EAU54502
Auxiliary lights
This model is equipped with LED-type
auxiliary lights.
If an auxiliary light does not come on,
have a Yamaha dealer check it.
EAU70540
Brake/tail light
This model is equipped with an LED-
type brake/tail light.
If the brake/tail light does not come on,
have a Yamaha dealer check it.
1. Auxiliary light
11
UBR7E0E0.book Page 32 Tuesday, October 25, 2016 2:44 PM

Vehicle care and storage
7-2
7 structed. Also, thoroughly rinse
the area off with water, immedi-
ately dry it, and then apply a cor-
rosion protection spray.
zImproper cleaning can damage
plastic parts (such as cowlings,
panels, windshields, headlight
lenses, meter lenses, etc.) and
the mufflers. Use only a soft,
clean cloth or sponge with wa-
ter to clean plastic. However, if
the plastic parts cannot be thor-
oughly cleaned with water, di-
luted mild detergent with water
may be used. Be sure to rinse
off any detergent residue using
plenty of water, as it is harmful
to plastic parts.
zDo not use any harsh chemical
products on plastic parts. Be
sure to avoid using cloths or
sponges which have been in
contact with strong or abrasive
cleaning products, solvent or
thinner, fuel (gasoline), rust re-
movers or inhibitors, brake fluid,
antifreeze or electrolyte.
zDo not use high-pressure wash-
ers or steam-jet cleaners since
they cause water seepage and
deterioration in the following ar-
eas: seals (of wheel and swing-
arm bearings, fork and brakes),
electric components (couplers,
connectors, instruments,
switches and lights), breather
hoses and vents.
zFor vehicles equipped with a
windshield: Do not use strong
cleaners or hard sponges as
they will cause dulling or
scratching. Some cleaningcompounds for plastic may
leave scratches on the wind-
shield. Test the product on a
small hidden part of the wind-
shield to make sure that it does
not leave any marks. If the wind-
shield is scratched, use a quality
plastic polishing compound
af-
ter washing.
NOTICE
ECAU0061
Use care when cleaning the radiator.
High-pressure washers may dam-
age the radiator fins. Do not spray
the radiator fins at an angle, and al-
ways keep the nozzle at least 50 cm
(20 in) away from the spins when
spraying.
After normal use
Remove dirt with warm water, a mild
detergent, and a soft, clean sponge,
and then rinse thoroughly with clean
water. Use a toothbrush or bottlebrush
for hard-to-reach areas. Stubborn dirt
and insects will come off more easily if
the area is covered with a wet cloth for
a few minutes before cleaning.
After riding in the rain, near the sea, or
on salt-sprayed roads
Since sea salt or salt sprayed on roads
during winter are extremely corrosive
in combination with water, carry out
the following steps after each ride in
the rain, near the sea, or on salt-
sprayed roads.
TIP
Salt sprayed on roads in the winter
may remain well into spring.
UBR7E0E0.book Page 2 Tuesday, October 25, 2016 2:44 PM

Vehicle care and storage
7-3
71. Clean the vehicle with cold water
and a mild detergent after the en-
gine has cooled down. NOTICE:
Do not use warm water since it
increases the corrosive action
of the salt.
[ECA10792]
2. Apply a corrosion protection spray
on all metal, including chrome-
and nickel-plated, surfaces to pre-
vent corrosion.
Cleaning the windshield
Avoid using any alkaline or strong acid
cleaner, gasoline, brake fluid, or any
other solvent. Clean the windshield
with a cloth or sponge dampened with
a mild detergent, and then wash it off
thoroughly with water. For additional
cleaning, use Yamaha Windshield
Cleaner or another high-quality wind-
shield cleaner. Some cleaning com-
pounds for plastics may leave
scratches on the windshield. Before
using such cleaners, test an area of the
windshield which does not affect your
visibility and which cannot be easily
recognized.
After cleaning
1. Dry the vehicle with a chamois or
an absorbing cloth.
2. Use a chrome polish to shine
chrome, aluminum, and stainless-
steel parts, including the exhaust
system. (Even the thermally in-
duced discoloring of stainless-
steel exhaust systems can be re-
moved through polishing.)3. To prevent corrosion, it is recom-
mended to apply a corrosion pro-
tection spray on all metal,
including chrome- and nickel-plat-
ed surfaces.
4. Use spray oil as a universal clean-
er to remove any remaining dirt.
5. Touch up minor paint damage
caused by stones, etc.
6. Wax all painted surfaces.
7. Let the vehicle dry completely be-
fore storing or covering it.WARNING
EWA17830
Contaminants on the brakes or tires
can cause loss of control.
zMake sure that there is no oil or
wax on the brakes or tires. If
necessary, clean the brake
discs and brake linings with a
regular brake disc cleaner or
acetone, and wash the tires with
warm water and a mild deter-
gent.
zBefore operating the vehicle
test its braking performance
and cornering behavior.
NOTICE
ECAU0022
zApply spray oil and wax spar-
ingly and make sure to wipe off
any excess.
zNever apply oil or wax to any
rubber parts, plastic parts or
headlight, taillight and meter
lenses, but treat them with a
suitable care product.
zAvoid using abrasive polishing
compounds as they will wear
away the paint.
UBR7E0E0.book Page 3 Tuesday, October 25, 2016 2:44 PM

Specifications
8-2
8
Track:
385 mm (15.2 in)
Front tire:
Type:
Tubeless
Size:
90/80-14M/C 43P
Manufacturer/model:
IRC/SCT-003
Rear tire:
Type:
Tubeless
Size:
130/70-13M/C 63P
Manufacturer/model:
IRC/SCT-003
Loading:
Maximum load:
167 kg (368 lb)
(Total weight of rider, passenger, cargo
and accessories)
Tire air pressure (measured on cold
tires):
1 person:
Front:
200 kPa (2.00 kgf/cm², 29 psi)
Rear:
225 kPa (2.25 kgf/cm², 33 psi)
2 persons:
Front:
200 kPa (2.00 kgf/cm², 29 psi)
Rear:
225 kPa (2.25 kgf/cm², 33 psi)
Front wheel:
Wheel type:
Cast wheel
Rim size:
14M/C x MT2.15
Rear wheel:
Wheel type:
Cast wheel
Rim size:
13M/C x MT3.50
Unified brake system:
Operation:
Activated by rear brake
Front brake:
Type:
Hydraulic disc brakeSpecified brake fluid:
DOT 4
Rear brake:
Type:
Hydraulic disc brake
Specified brake fluid:
DOT 4
Front suspension:
Type:
Telescopic fork
Spring:
Coil spring
Shock absorber:
Hydraulic damper
Wheel travel:
90 mm (3.5 in)
Rear suspension:
Type:
Unit swing
Spring:
Coil spring
Shock absorber:
Hydraulic damper
Wheel travel:
90 mm (3.5 in)
Electrical system:
System voltage:
12 V
Ignition system:
TCI
Charging system:
AC magneto
Battery:
Model:
YTZ7V
Voltage, capacity:
12 V, 6.0 Ah (10 HR)
Bulb wattage:
Headlight:
LED
Brake/tail light:
LED
Front turn signal light:
10.0 W
Rear turn signal light:
10.0 W
Auxiliary light:
LED
License plate light:
5.0 W
UBR7E0E0.book Page 2 Tuesday, October 25, 2016 2:44 PM

10-1
10
Index
A
ABS (for ABS models) ........................... 3-11
ABS warning light (for ABS models) ....... 3-4
Acceleration and deceleration ................ 5-3
Accessory box ...................................... 3-17
Air filter and V-belt case air filter
elements ............................................. 6-14
Auxiliary DC connector ......................... 3-22
Auxiliary DC jack ................................... 3-21
Auxiliary lights ....................................... 6-32
B
Battery .................................................. 6-28
Brake fluid, changing ............................ 6-23
Brake fluid level, checking .................... 6-22
Brake lever, front .................................. 3-10
Brake lever, rear.................................... 3-10
Brake levers, lubricating ....................... 6-25
Brake/tail light ....................................... 6-32
Braking.................................................... 5-3
C
Cables, checking and lubricating ......... 6-24
Care ........................................................ 7-1
Catalytic converter ................................ 3-14
Centerstand and sidestand,
checking and lubricating .................... 6-25
Coolant ................................................. 6-12
Coolant temperature warning light ......... 3-3
D
Data recording, vehicle ........................... 9-2
Diagnostic connector.............................. 9-2
Dimmer switch ........................................ 3-9
E
Eco indicator light ................................... 3-3
Engine break-in....................................... 5-4
Engine oil and oil strainer........................ 6-9
Engine serial number .............................. 9-1
Engine trouble warning light ................... 3-3
F
Final transmission oil ............................ 6-11
Front and rear brake pads, checking.... 6-21
Front brake lever free play, checking ... 6-20
Front fork, checking .............................. 6-26
Fuel ....................................................... 3-12
Fuel consumption, tips for reducing ....... 5-4
Fuel tank cap ........................................ 3-12
Fuel tank overflow hose ........................ 3-14
Fuses, replacing.................................... 6-30
H
Handlebar switches ................................ 3-9
Headlight............................................... 6-31High beam indicator light ....................... 3-3
Horn switch ............................................ 3-9
I
Identification numbers ............................ 9-1
Ignition circuit cut-off system............... 3-19
Indicator lights and warning lights ......... 3-3
K
Keyhole shutter ...................................... 3-2
L
Leaning system, checking .................... 6-28
License plate light bulb, replacing........ 6-33
Luggage hook ...................................... 3-18
M
Main switch/steering lock....................... 3-1
Maintenance and lubrication, periodic ... 6-4
Maintenance, emission control
system.................................................. 6-3
Matte color, caution ............................... 7-1
Model label ............................................. 9-1
Multi-function meter unit ........................ 3-5
P
Panel, removing and installing ............... 6-7
Parking ................................................... 5-5
Part locations ......................................... 2-1
Passenger footrest ............................... 3-15
R
Rear brake lever free play, checking .... 6-20
S
Safe-riding points ................................... 1-6
Safety information .................................. 1-1
Seat ...................................................... 3-15
Sidestand ............................................. 3-18
Spark plug, checking ............................. 6-8
Specifications ......................................... 8-1
Starting off.............................................. 5-2
Starting the engine ................................. 5-1
Start switch ............................................ 3-9
Steering, checking................................ 6-26
Steering tie rod, checking .................... 6-27
Storage ................................................... 7-4
Storage compartment .......................... 3-16
T
Throttle grip and cable,
checking and lubricating .................... 6-24
Throttle grip free play, checking........... 6-16
Tires ...................................................... 6-17
Tool kit.................................................... 6-2
Troubleshooting ................................... 6-34
Troubleshooting charts ........................ 6-35
Turn signal indicator lights ..................... 3-3
UBR7E0E0.book Page 1 Tuesday, October 25, 2016 2:44 PM