drain bolt YAMAHA XT600E 2002 Owners Manual

6-11
PERIODIC MAINTENANCE AND MINOR REPAIR
6
EC000000
cCDo not operate the motorcycle
until you know that the engine oil
level is sufficient.
EW000065
wNever remove the engine oil tank
cap after high-speed operation,
otherwise hot engine oil could
spout out and cause damage or
injury. Always let the engine oil
cool down sufficiently before
removing the oil tank cap.5. If the engine oil is below the min-
imum level mark, add sufficient
oil of the recommended type to
raise it to the correct level.
6. Install the oil filler cap and the oil
filler cap cover.4. Check the washers for damage
and replace them if necessary.
NOTE:
Skip steps 5–8 if the oil filter element
is not being replaced.5. Remove the oil filter element
cover by removing the bolts.NOTE:
The oil filter element cover is secured
by two bolts and a drain bolt. First,
remove the drain bolt to drain the oil
filter element cavity.
1
32
1. Oil filter cover bolt (×2)
2. Oil filter cover
3. Oil filter drain bolt
To change the engine oil (with or
without oil filter element replace-
ment)
1. Start the engine, warm it up for
several minutes, and then turn it
off.
2. Place an oil pan under the
engine to collect the used oil.
3. Remove the oil filler cap cover,
the oil filler cap and the drain
bolts to drain the oil from the
crankcase and oil tank.1. Drain bolt (oil tank)
2. Drain bolt (crankcase)1
2
4PT-E7 (English) 6/29/01 9:13 AM Page 48

6-12
PERIODIC MAINTENANCE AND MINOR REPAIR
6 6. Remove and replace the oil filter
element.
7. Check the O-rings for damage
and replace them if necessary.
8. Install the oil filter element cover
by installing the bolts, then tight-
ening them to the specified
torque.
NOTE:
Make sure that the O-ring is properly
seated.9. Install the engine oil drain bolts,
and then tighten them to the
specified torques.
10. Add the specified amount of the
recommended engine oil, install
and tighten the oil filler cap, and
then install the oil filler cap cover.
ECA00105
cC8In order to prevent clutch slip-
page (since the engine oil also
lubricates the clutch), do not
mix any chemical additives
with the oil or use oils of grade
“CD” or higher. In addition, do
not use oils labeled “ENERGY
CONSERVING II” or higher.
8Make sure that no foreign
material enters the crankcase.
1
2
1. Oil filter element
2. O-ring (×2)
Tightening torque:
Oil filter element cover bolt:
10 Nm (1.0 m0kgf)
Tightening torques:
Engine oil drain bolt
(crankcase):
30 Nm (3.0 m0kgf)
Engine oil drain bolt (oil tank):
18 Nm (1.8 m0kgf)
Recommended engine oil:
See page 8-1.
Oil quantity:
Without oil filter element
replacement:
2.7 L
With oil filter element
replacement:
2.8 L
Total amount (dry engine):
3.3 L
4PT-E7 (English) 6/29/01 9:13 AM Page 49

7-4
MOTORCYCLE CARE AND STORAGE
7
StorageStorageShort-term
Always store your motorcycle in a
cool, dry place and, if necessary, pro-
tect it against dust with a porous
cover.
ECA00014
cC8Storing the motorcycle in a
poorly ventilated room or cov-
ering it with a tarp, while it is
still wet, will allow water and
humidity to seep in and cause
rust.
8To prevent corrosion, avoid
damp cellars, stables (because
of the presence of ammonia)
and areas where strong chemi-
cals are stored.
Long-term
Before storing your motorcycle for
several months:
1. Follow all the instructions in the
“Care” section of this chapter.
2. For motorcycles equipped with a
fuel cock that has an “OFF” posi-
tion: Turn the fuel cock lever to
“OFF”.
3. Drain the carburetor float cham-
ber by loosening the drain bolt;
this will prevent fuel deposits
from building up. Pour the
drained fuel into the fuel tank.
4. Fill up the fuel tank and add fuel
stabilizer (if available) to prevent
the fuel tank from rusting and the
fuel from deteriorating.
5. Perform the following steps to
protect the cylinder, piston rings,
etc. from corrosion.
a. Remove the spark plug cap
and spark plug.
b. Pour a teaspoonful of engine
oil into the spark plug bore.c. Install the spark plug cap onto
the spark plug, and then place
the spark plug on the cylinder
head so that the electrodes
are grounded. (This will limit
sparking during the next step.)
d. Turn the engine over several
times with the starter. (This
will coat the cylinder wall with
oil.)
e. Remove the spark plug cap
from the spark plug, and then
install the spark plug and the
spark plug cap.
EWA00003
wTo prevent damage or injury from
sparking, make sure to ground the
spark plug electrodes while turn-
ing the engine over.
4PT-E7 (English) 6/29/01 9:13 AM Page 85