stop start YAMAHA XT600E 2002 Owners Manual

3-1
EAU00029
Main switch/steering lockMain switch/steering lockThe main switch/steering lock con-
trols the ignition and lighting systems,
and is used to lock the steering. The
various positions are described
below.
EAU00036
ON
All electrical systems are supplied
with power, and the engine can be
started. The key cannot be removed.
EAU00038
OFF
All electrical systems are off. The key
can be removed.
EW000016
wNever turn the key to “OFF” or
“LOCK” while the motorcycle is
moving, otherwise the electrical
systems will be switched off,
which may result in loss of control
or an accident. Make sure that the
motorcycle is stopped before turn-
ing the key to “OFF” or “LOCK”.
EAU01590
.
(Parking)
The steering is locked, and the tail-
light and auxiliary light are on, but all
other electrical systems are off. The
key can be removed.
The steering must be locked before
the key can be turned to “
.
”.
ECA00043
cCDo not use the parking position for
an extended length of time, other-
wise the battery may discharge.
EAU00027
INSTRUMENT AND CONTROL FUNCTIONS
3
ON
OFF
LOCK.
EAU00040
LOCK
The steering is locked, and all electri-
cal systems are off. The key can be
removed.
To lock the steering1. Turn the handlebars all the way
to the left.
2. Push the key in from the “OFF”
position, and then turn it to
“LOCK” while still pushing it.
3. Remove the key.
To unlock the steeringPush the key in, and then turn it to
“OFF” while still pushing it.
12
1. Push.
2. Turn.
4PT-E7 (English) 6/29/01 9:13 AM Page 14

3-4
INSTRUMENT AND CONTROL FUNCTIONS
3
EAU03890
Engine stop switch “$/#”Engine stop switchSet this switch to “#” before starting
the engine. Set this switch to “$” to
stop the engine in case of an emer-
gency, such as when the motorcycle
overturns or when the throttle cable is
stuck.
EAU00143
Start switch “,”Start switchPush this switch to crank the engine
with the starter.
EC000005
cCSee page 5-1 for starting instruc-
tions prior to starting the engine.
1
2
,
1. Engine stop switch “$/#”
2. Start switch “,”
EAU00152
Clutch leverClutch leverThe clutch lever is located at the left
handlebar grip. To disengage the
clutch, pull the lever toward the han-
dlebar grip. To engage the clutch,
release the lever. The lever should
be pulled rapidly and released slowly
for smooth clutch operation.
The clutch lever is equipped with a
clutch switch, which is part of the igni-
tion circuit cut-off system. (See page
3-12 for an explanation of the ignition
circuit cut-off system.)
1
1. Clutch lever
4PT-E7 (English) 6/29/01 9:13 AM Page 17

3-13
INSTRUMENT AND CONTROL FUNCTIONS
3
With the engine turned off:
1. Move the sidestand down.
2. Make sure that the engine stop switch is set to “
#”.
3. Turn the key to “ON”.
4. Shift the transmission into the neutral position.
5. Push the start switch.
Does the engine start?
The neutral switch may be defective.
The motorcycle should not be ridden until
checked by a Yamaha dealer.
With the engine still running:
6. Move the sidestand up.
7. Keep the clutch lever pulled.
8. Shift the transmission into gear.
9. Move the sidestand down.
Does the engine stall?After the engine has stalled:
10. Move the sidestand up.
11. Keep the clutch lever pulled.
12. Push the start switch.
Does the engine start?
The sidestand switch may be defective.
The motorcycle should not be ridden until
checked by a Yamaha dealer.The clutch switch may be defective.
The motorcycle should not be ridden until
checked by a Yamaha dealer.
NO
NOTE:This check is most reliable if performed with
a warmed-up engine.
YESYES NO
The system is OK. The motorcycle can be ridden.
YES NO
4PT-E7 (English) 6/29/01 9:13 AM Page 26

1. Turn the fuel cock lever to “ON”.
2. Turn the key to “ON” and make
sure that the engine stop switch
is set to “#”.
3. Shift the transmission into the
neutral position.NOTE:
When the transmission is in the neu-
tral position, the neutral indicator light
should be on, otherwise have a
Yamaha dealer check the electrical
circuit.4. Turn the starter (choke) on and
completely close the throttle.
(See page 3-9 for starter (choke)
operation.)
5. Start the engine by pushing the
start switch.
5-1
EAU00372
OPERATION AND IMPORTANT RIDING POINTS
5
EAU00373
w8Become thoroughly familiar
with all operating controls and
their functions before riding.
Consult a Yamaha dealer
regarding any control or func-
tion that you do not thorough-
ly understand.
8Never start the engine or oper-
ate it in a closed area for any
length of time. Exhaust fumes
are poisonous, and inhaling
them can cause loss of con-
sciousness and death within a
short time. Always make sure
that there is adequate ventila-
tion.
8Before starting out, make sure
that the sidestand is up. If the
sidestand is not raised com-
pletely, it could contact the
ground and distract the opera-
tor, resulting in a possible loss
of control.
EAU03515
Starting the engineStarting the engineIn order for the ignition circuit cut-off
system to enable starting, one of the
following conditions must be met:
8The transmission is in the neutral
position.
8The transmission is in gear with
the clutch lever pulled and the
sidestand up.
EW000054
w8Before starting the engine,
check the function of the igni-
tion circuit cut-off system
according to the procedure
described on page 3-13.
8Never ride with the sidestand
down.
4PT-E7 (English) 6/29/01 9:13 AM Page 32

6-13
PERIODIC MAINTENANCE AND MINOR REPAIR
6
EC000076
cCAfter changing the engine oil, be
sure to check the oil pressure as
described below.11. Remove the air bleed screw, and
then start the engine. If oil does
not seep out of the hole after a
few minutes, immediately stop
the engine and have a Yamaha
dealer check for the cause. If oil
seeps out of the hole, turn the
engine off and install the air
bleed screw.12. Start the engine, and then let it
idle for several minutes while
checking it for oil leakage. If oil is
leaking, immediately turn the
engine off and check for the
cause.
13. Turn the engine off, and then
check the oil level and correct it if
necessary.
1
1. Air bleed screw
EAU03514
Cleaning the air filter
elementAir filter element, cleaningThe air filter element should be
cleaned at the intervals specified in
the periodic maintenance and lubrica-
tion chart. Clean the air filter element
more frequently if you are riding in
unusually wet or dusty areas.
1. Remove panel B. (See page 6-8
for panel removal and installation
procedures.)
2. Remove the air filter case cover
by removing the screws, and
then pull the air filter element
out.
1
1
1. Screw (×7)
4PT-E7 (English) 6/29/01 9:13 AM Page 50

6-15
PERIODIC MAINTENANCE AND MINOR REPAIR
6
EAU00632
Adjusting the engine idling
speedEngine idling speedThe engine idling speed must be
checked and, if necessary, adjusted
as follows at the intervals specified in
the periodic maintenance and lubrica-
tion chart.
1. Start the engine and warm it up
for several minutes at 1,000–
2,000 r/min while occasionally
revving it to 4,000–5,000 r/min.NOTE:
The engine is warm when it quickly
responds to the throttle.
NOTE:
If the specified idling speed cannot
be obtained as described above,
have a Yamaha dealer make the
adjustment.
2. Check the engine idling speed
and, if necessary, adjust it to
specification by turning the throt-
tle stop screw. To increase the
engine idling speed, turn the
screw in direction a. To
decrease the engine idling
speed, turn the screw in direction
b.
1
b
a
1. Throttle stop screw
Engine idling speed:
1,200–1,400 r/min
(Except for CH)
1,300–1,400 r/min
(For CH)
4PT-E7 (English) 6/29/01 9:13 AM Page 52

6-36
PERIODIC MAINTENANCE AND MINOR REPAIR
6 2. Remove the defective bulb by
pushing it in and turning it coun-
terclockwise.
3. Insert a new bulb into the socket,
push it in, and then turn it clock-
wise until it stops.
4. Install the lens by installing the
screws.
EC000108
cCDo not overtighten the screws,
otherwise the lens may break.
1
1. Bulb
To service the rear wheel
Raise the rear wheel off the ground
by using a motorcycle stand or, if a
motorcycle stand is not available, by
placing a jack either under each side
of the frame in front of the rear wheel
or under each side of the swingarm.
EAU01579
Supporting the motorcycleSupporting the motorcycleSince this model is not equipped with
a centerstand, follow these precau-
tions when removing the front and
rear wheel or performing other main-
tenance requiring the motorcycle to
stand upright. Check that the motor-
cycle is in a stable and level position
before starting any maintenance. A
strong wooden box can be placed
under the engine for added stability.
To service the front wheel
1. Stabilize the rear of the motorcy-
cle by using a motorcycle stand
or, if an additional motorcycle
stand is not available, by placing
a jack under the frame in front of
the rear wheel.
2. Raise the front wheel off the
ground by using a motorcycle
stand.
4PT-E7 (English) 6/29/01 9:13 AM Page 73

INDEX
E
Engine break-in ..................................... 5-4
Engine idling speed ............................. 6-15
Engine oil and oil filter element ........... 6-10
Engine, starting a warm ......................... 5-2
F
Front and rear brake pads, checking ... 6-22
Front fork, checking ............................. 6-29
Front wheel........................................... 6-37
Installing ............................................ 6-37
Removing .......................................... 6-37
Fuel ....................................................... 3-6
Fuel cock ............................................... 3-8
Fuel consumption, tips for reducing ...... 5-4
Fuel tank cap ......................................... 3-6
Fuse, replacing .................................... 6-32
H
Handlebar switches ............................... 3-3
Light switch ......................................... 3-3
Pass switch ......................................... 3-3
Dimmer switch .................................... 3-3
Turn signal switch ............................... 3-3
Horn switch ......................................... 3-3
Engine stop switch .............................. 3-4
Start switch ......................................... 3-4
Headlight bulb, replacing ..................... 6-33
Helmet holder ...................................... 3-10
I
Identification numbers ........................... 9-1
Ignition circuit cut-off system ............... 3-12
Indicator lights ....................................... 3-2
High beam indicator light .................... 3-2
Neutral indicator light .......................... 3-2
Turn signal indicator light .................... 3-2
K
Key identification number ...................... 9-1
M
Main switch/steering lock ...................... 3-1
Model label ............................................ 9-2
P
Parking .................................................. 5-5
Part locations ......................................... 2-1
Periodic maintenance and lubrication
chart .................................................... 6-3
Pre-operation check list ......................... 4-1
R
Rear brake light switch, adjusting ........ 6-22
Rear suspension, lubricating ............... 6-29
Rear wheel ........................................... 6-39
Removing .......................................... 6-39
Install ................................................ 6-40
S
Seat ....................................................... 3-9
Shift pedal ............................................. 3-5
Shift points (for Switzerland only) .......... 5-3
Shifting .................................................. 5-3
Shock absorber assembly, adjusting ... 3-10
Sidestand ............................................ 3-11
A
Air filter element, cleaning ................... 6-13
B
Battery ................................................. 6-31
Brake and clutch levers, checking and
lubricating ......................................... 6-28
Brake and shift pedals, checking and
lubricating ......................................... 6-28
Brake fluid level, checking ................... 6-23
Brake fluid, changing ........................... 6-24
Brake lever ............................................ 3-5
Brake lever free play, adjusting ........... 6-21
Brake pedal ........................................... 3-5
Brake pedal position, adjusting ........... 6-21
C
Cables, checking and lubricating ......... 6-27
Carburetor, adjusting ........................... 6-14
Care ....................................................... 7-1
Clutch lever ........................................... 3-4
Clutch lever free play, adjusting .......... 6-20
Conversion table ................................... 8-5
Cowling and panels, removing and
installing .............................................. 6-6
D
Drive chain slack ................................. 6-25
Checking ........................................... 6-25
Adjusting ........................................... 6-25
Drive chain, lubricating ........................ 6-26
4PT-E7 (English) 6/29/01 9:13 AM Page 96