Abarth 500 2012 Owner handbook (in English)

60
SAFETY
DEVICES
CORRECT USE
OF THE
CAR
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
CAR
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX
YOUR CAR
ELECTRICAL/ELECTRONIC
DEVICE INSTALLATION
Electrical and electronic devices installed
after buying the car by after-market ser-
vice must carry the following label:
Fiat Auto S.p.A. authorises the installation
of transceiving devices provided that they
are installed according to rules of good en-
gineering practice respecting the manu-
facturer’s indications by a specialised cen-
tre.
IMPORTANT Traffic police may not allow
the car on the road in the event of as-
sembly of devices which imply modifica-
tions to the features of the car. This may
also cause lapse of warranty in relation to
faults caused by the change or either di-
rectly or indirectly related to it.
Fiat Auto S.p.A. shall not be liable for dam-
age caused by the installation of acces-
sories either not supplied or recom-
mended by Fiat Auto S.p.A. and/or not in-
stalled in compliance with the provided in-
structions.RADIO TRANSMITTERS
AND CELLULAR PHONES
Radio transceiver equipment (vehicle mo-
bile phones, CB radios, amateur radio and
similar equipment) shall not be used inside
the car unless a separate aerial is mount-
ed on the roof.
IMPORTANT The use of these devices in-
side the passenger compartment (without
a separate aerial) may cause the vehicle
electrical systems to malfunction. This
could compromise safety in addition to
constituting a potential hazard for pas-
sengers.
In addition, transmission and reception of
these devices may be affected by the
shielding effect of the car body. With re-
gards to the use of EC-approved mobile
phones (GSM, GPRS, UMTS), adhere
strictly to the instructions for use provid-
ed by the mobile phone manufacturer.ACCESSORIES
PURCHASED
BY THE OWNER
If after buying the car, you decide to install
electrical accessories that require a per-
manent electric supply (alarm, satellite an-
titheft system, etc.) or accessories that in
any case burden the electric supply, con-
tact Abarth Dealership, whose qualified
personnel, besides suggesting the most
suitable devices belonging to Lineaccessori
Abarth, will also evaluate the overall elec-
tric absorption, checking whether the car’s
electric system is able to withstand the
load required, or whether it needs to be
integrated with a more powerful battery.

61
SAFETY
DEVICES
CORRECT USE
OF THE
CAR
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
CAR
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX
YOUR CAR
FUEL FILLER CAP fig. 59
The cap Bis provided with a loss pre-
vention device Cwhich secures it to the
lid A.
Unscrew cap Busing the ignition key. The
airtight closing may determine a slight in-
crease of pressure in the tank. A suction
noise when you release the cap is there-
fore entirely normal. When refuelling, fas-
ten the cap to the device inside the lid as
shown in figure.
AT THE FILLING
STATION
Use unleaded petrol only, with octane
number (R.O.N.) not lower than 95.
IMPORTANT An inefficient catalyst leads
to harmful exhaust emissions, thus con-
tributing to air pollution.
IMPORTANT Never use leaded petrol,
even in small amount or in an emergency,
as this would damage the catalyst beyond
repair.
REFILLING
To ensure full fuel tank refilling, perform
two topping up after the first stop of the
nozzle. Do not top up further; this may
cause anomalies in the fuel supply system.Do not approach naked
flames or lit cigarettes to the
fuel filler: fire risk. Keep your
face away from the fuel filler
to prevent breathing in harmful
vapours.
fig. 59F0S059Ab

62
SAFETY
DEVICES
CORRECT USE
OF THE
CAR
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
CAR
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX
YOUR CAR
PROTECTING THE
ENVIRONMENT
The devices for curtailing petrol engine
emissions are the following:
❒three-way catalytic converter;
❒Lambda sensors;
❒fuel evaporation prevention system.
In addition, do not let the engine run, even
for a test, with one or more spark plugs
disconnected.
The catalytic converter de-
velops high temperature dur-
ing operation. Do not park on grass,
dry leaves, pine needles or other flam-
mable material: fire risk .
WARNING

63
CORRECT USE
OF THE
CAR
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
CAR
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX
YOUR CAR
SAFETY
DEVICES
SEAT BELTS ........................................................................... 64
S.B.R. SYSTEM ....................................................................... 64
PRETENSIONERS.................................................................. 65
CARRYING CHILDREN SAFELY...................................... 67
ASSEMBLY SETUP FOR ISOFIX CHILD SEAT ............. 71
FRONT AIRBAGS................................................................. 73
WINDOW BAGS................................................................ 75
S S
A A
F F
E E
T T
Y Y
D D
E E
V V
I I
C C
E E
S S

64
CORRECT USE
OF THE
CAR
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
CAR
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX
YOUR CAR
SAFETY
DEVICES
The reel may lock when the car is parked
on a steep slope: this is perfectly normal.
Furthermore, the reel mechanism locks
the belt if it is pulled and in the event of
sudden braking, collisions and on high
speed bends.
The rear seat is fitted with inertial seat
belts with three anchor points and reel.
S.B.R. SYSTEM
The car is provided with the S.B.R. (Seat
Belt Reminder) system, which warns the
driver and the front passenger if the seat
belt is not buckled, as follows:
❒warning light continuous activation of the beeper for
the first 6 seconds;
❒warning light activation of the beeper for the next 96
seconds;
For permanent deactivation, contact
Abarth Dealership.
the S.B.R. system CAN also be reset
through the set-up menu.
SEAT BELTS
USING THE SEAT BELTS fig. 1
Wear the belt keeping the chest straight
and rested against the backrest.
To fasten the seat belts, hold the tongue
Aand insert it into the buckle B, until
hearing the locking click. At removal, if it
jams, let it rewind for a short stretch, then
pull it out again without jerking.
Press button Cto release the belt. Ac-
company the belt while it is being re-
wound to prevent twisting. Through the
reel, the belt automatically adapts to the
body of the passenger wearing it, allowing
freedom of movement.
fig. 1F0S060Ab
Never press button C when
travelling.
WARNING
Remember that, in the event
of a violent collision, the
passengers of the rear seats who do
wear seat belts, besides exposing
themselves to a significant danger,
represent a danger for the passengers
of the front seats.
WARNING

65
CORRECT USE
OF THE
CAR
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
CAR
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX
YOUR CAR
SAFETY
DEVICES
PRETENSIONERS
To increase the efficiency of the seat belts,
the car is fitted with front pretensioners.
These devices, in the event of a violent
crash, rewind the seat belts a few cen-
timetres. In this way they ensure that the
seat belt adheres perfectly to the wearer
before the restraining action begins. The
seat belt locks to indicate that the device
has intervened; the seat belt cannot be
drawn back up even when guiding it man-
ually.
This car is provided with a second pre-
tensioner (in the sill board area). Its acti-
vation is signalled by the shortening of the
metallic cable.
IMPORTANT To obtain the highest de-
gree of protection from the action of the
pretensioning device, wear the seat belt
keeping it firmly close to the chest and
pelvis.
A small amount of smoke may be pro-
duced. This smoke is in no way toxic and
presents no fire hazard. The pretension-
er does not require any maintenance or
greasing. Anything that modifies its origi-
nal conditions invalidates its efficiency. If
due to unusual natural events (floods, seas
storm, etc.) the device has been affected
by water and mud, it must necessarily be
replaced.LOAD LIMITERS
To increase passenger’s safety, the reels
contain a load limiter which allows con-
trolled sag in such a way as to dose the
force acting on the chest and shoulders
during the belt restraining action in case
of front crash.
GENERAL INSTRUCTIONS
FOR USING THE SEAT BELTS
The driver is responsible for respecting
and ensuring that all the other occupants
of the car also respect the local laws in
force in relation to the use of seat belts.
Always fasten the seat belts before start-
ing off.
Seat belts must also be used by pregnant
women: risk will be significantly reduced
for both the expectant mother and the
child in the event of an accident. Pregnant
women must position the lower part of
the belt very low down so that it passes
under the abdomen (see fig. 2). The pretensioner can only
be used once. Go to a Abarth
Dealership to have it replaced after
is has been deployed. The expiration
date is shown on the label on the
door edge: refer to the Abarth Deal-
ership when it’s time to replace the
device.
WARNING
Operations which lead to
knocks, vibrations or localised
heating (over 100°C for a
maximum of 6 hours) in the
area around the pretensioners may
cause damage or trigger them. These
devices are not affected by vibrations
caused by irregularities of the road sur-
face or low obstacles such as kerbs, etc.
Contact a Abarth Dealership for any
assistance.

66
CORRECT USE
OF THE
CAR
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
CAR
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX
YOUR CAR
SAFETY
DEVICES
fig. 2F0S061Ab
For maximum safety, keep
the back of your seat up-
right, lean back into it and make sure
the seat belt fits closely across your
chest and hips. Always fasten the seat
belts on both the front and the rear
seats. Travelling without seat belts
will increase the risk of severe injury
and even death in the event of an ac-
cident.
Never disassemble or tamper with the
seat belt or pretensioner components.
All interventions must be performed
by qualified and authorised person-
nel only. Always go to a Abarth Deal-
ership.
WARNINGIMPORTANT Each seat belt may only be
used by a single person: do not carry chil-
dren on your lap with one seat belt pro-
tecting both fig. 4. In general, do not place
any objects between the person and belt. IMPORTANT The belt must not be twist-
ed. The upper part must cross the shoul-
der and the chest diagonally. The lower
part must fit the hips (as shown in fig. 3)
rather than the abdomen of the passen-
ger. Do not use devices (clips, etc.) to hold
the seat belt away from your body.
fig. 3F0S062Abfig. 4F0S063Ab
If the belt has been subject-
ed to heavy stress, for ex-
ample after an accident, it should be
changed completely together with
the anchors, anchor fastening screws
and the pretensioners. In fact, even if
the belt has no visible defects, it could
have lost its resilience.
WARNING

67
CORRECT USE
OF THE
CAR
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
CAR
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX
YOUR CAR
SAFETY
DEVICES
SEAT BELTS MAINTENANCE
Observe the following:
❒always use the belt with the tap taut and
never twisted; make sure that it is free
to run without impediments;
❒replace the belt after an accident of a
certain severity even if it does not ap-
pear damaged. Always replace the belt
if the pretensioners were deployed.
❒to clean the belt, wash by hand with wa-
ter and mild soap, rinse and leave to dry
in the shade. Do not use strong deter-
gents, bleach, paints or any other sub-
stance which could damage the belt fi-
bres;
❒keep the reels dry: correct operation
may only be ensured if the reels are dry;
❒replace the seat belt when showing sig-
nificant wear or cut signs.
CARRYING CHILDREN
SAFELY
For optimal protection in the event of a
crash, all passengers must be seated and
wearing adequate restraint systems.
This is even more important for children.
This prescription is compulsory in all EC
countries according to EC Directive
2003/20/EC.
A child’s head is larger and heavier in pro-
portion to his/her body and the child’s
muscular and bone structures are not ful-
ly developed.
For this reason, they require restraint sys-
tems which are different from those used
by adults to protect them in the event of
an accident.
The research results in relation to the best
protection for children is illustrated in Eu-
ropean Regulation ECE-R44 which divides
the restraint systems into five groups in
addition to making their use compulsory:
Group 0 - 0-10 kg in weight
Group 0+ - 0-13 kg in weight
Group 1 9-18 kg in weight
Group 2 15-25 kg in weight
Group 3 22 - 36 kg in weight
SEVERE DANGER: Do not
arrange child seats facing
backwards on the front seat
if the passenger’s airbag is
on. Deployment of the
airbag in an accident could
cause fatal injuries to the baby. It is
advisable to carry children on the rear
seat, which is the most protected po-
sition in the event of an accident.
Child seats must not be fitted on the
front seat of cars provided with pas-
senger air bag, whose deployment in
an accident could cause fatal injuries
to the baby. If necessary, children can
stay on the front seat, if the passen-
ger’s airbag can be disabled. Verify
that the airbag is actually deactivat-
ed, observing the warning light
Fon
the dashboard (see “Front airbag -
passenger side” at paragraph “Front
airbags”). Move the passenger’s seat
as far back as possible to avoid con-
tact between the cradle and the dash-
board.
WARNING

68
CORRECT USE
OF THE
CAR
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
CAR
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX
YOUR CAR
SAFETY
DEVICES
All restraint devices must bear the certi-
fication data, together with the control
mark, on a solidly fixed label which must
absolutely never be removed.
Over 1.50 m in height, from the point of
view of restraint systems, children are
considered as adults and wear the seat
belts normally. Lineaccessori Abarth in-
cludes child restraint systems for each
weight group.
These devices are recommended having
been specifically designed for Abarth cars.
GROUP 0 and 0+
Babies up to 13 kg must be carried facing
backwards on a cradle seat, which, sup-
porting the head, does not induce stress
on the neck in the event of sharp decel-
eration.
The cradle is restrained by the car seat
belts, as shown in fig. 5and in turn it must
restrain the child with its own belts.
fig. 5F0S064Ab
GROUP 1
Starting from 9 kg to 18 kg in weight, chil-
dren may be carried facing forwards, with
seat fitted with front cushion, through
which the car seat belt restrains both child
and seat fig. 6.
fig. 6F0S065Ab
The figures are indicative for assembly purposes only. Refer to the
instructions supplied with the child restraint.
Some child restraint systems for weight group 0 and 1 have a rear attachment to
the car seat belts and its own seat belts for securing the child. Due to their weight,
they may be dangerous if incorrectly mounted (e.g. if fastened to the car seat belts
with a cushion in between). Follow the assembly instructions carefully.
WARNING

69
CORRECT USE
OF THE
CAR
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
CAR
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX
YOUR CAR
SAFETY
DEVICES
GROUP 3
For children from 22 kg to 36 kg the size
of the child’s chest no longer requires a
support to space the child’s back from the
seat back.
Fig. 8shows proper child seat position-
ing on the rear seat.
Children taller than 1.50 m can wear seat
belts like adults.
fig. 8F0S067Ab
The figures are indicative for
assembly purposes only. Re-
fer to the instructions supplied with
the child restraint.
WARNING
GROUP 2
Children from 15 to 25 kg may use the car
seat belts directly fig. 7.
The child seat is only needed to position
the child correctly with respect to the
belts so that the diagonal section crosses
the child’s chest and never the neck and is
snug on the hips not the abdomen.
fig. 7F0S066Ab
The figures are indicative for
assembly purposes only. Re-
fer to the instructions supplied with
the child restraint.
WARNING