stop start Abarth Punto 2012 Owner handbook (in English)

145
KNOWING
YOUR VEHICLE
SAFETY
STARTING
AND DRIVING
WARNING LIGHTS
AND MESSAGES
IN AN
EMERGENCY
MAINTENANCE
AND CARE
TECHNICAL
SPECIFICATIONS
CONTENTS
Contact an Abarth Dealership as soon
as possible if the warning light Udoes
not light up when the key is turned to MAR or
if, during travel, the warning light comes on
either constantly or flashing (along with a
message on the display). The operation of the
warning light Umay be checked by the traffic
control authorities using specific devices. Always
comply with the traffic regulations in force in
the country where you are driving.
WARNING
If the light flashes, release the accelerator pedal to
reduce engine revs until the warning light stops flashing;
continue the journey at a moderate speed, trying to
avoid driving conditions that may cause further flashing,
and contact an Abarth Dealership as soon as possible. EXCESSIVE ENGINE COOLANT
TEMPERATURE (red)
When the key is turned to the MAR position
the warning light comes on but should go out after a
few seconds. The warning light turns on when the
engine is overheated. If the warning light comes on
when driving, proceed as follows:
❒ when driving normally: stop the car, switch off the
engine and check that the water level in the
reservoir is not below the MIN mark. If it is not, wait
for a few minutes for the engine to cool down then
slowly and carefully open the cap, top up with
coolant and check that the level is between the MIN
and MAX marks. Also check visually for any fluid
leaks. Contact an Abarth Dealership if the warning
should come on when the engine is started again.
❒ if the vehicle is used under demanding conditions
(e.g. towing trailers uphill or fully loaded): slow down
and, if the light stays on, stop the car. Wait for 2 or
3 minutes with the engine running and slightly
accelerated to further favour the coolant circulation.
Then stop the engine. Check correct liquid level as
described above.
IMPORTANT Over demanding routes, it is advisable to
keep the engine on and slightly accelerated for a few
minutes before switching it off.
The display shows the dedicated message.
ç
141-150 GPUNTO EVO Abarth GB 2ed 8-11-2010 14:43 Pagina 145

149
KNOWING
YOUR VEHICLE
SAFETY
STARTING
AND DRIVING
WARNING LIGHTS
AND MESSAGES
IN AN
EMERGENCY
MAINTENANCE
AND CARE
TECHNICAL
SPECIFICATIONS
CONTENTS
TYRE PRESSURE CHECK
(amber)
TYRE PRESSURE LOW (amber)
TYRE PRESSURE UNSUITABLE FOR
SPEED
(amber)
(for versions/markets where provided)
Check tyre pressures
The symbol is shown on the display to indicate the flat
tyre. Should two or more tyres be flat, the display will
show the indications corresponding to each tyre in
sequence.
Restore correct tyre pressures as soon as possible (see
“Cold tyre pressures” in the “Technical specifications”
section).
Tyre pressure low
The symbol is shown on the display if the pressure of
one or more tyres drops below the preset level. In this
way the TPMS system warns the driver that one or
more tyres may be dangerously flat and liable to
puncture.
n
IMPORTANT Do not continue driving with one or
more flat tyres as handling may be compromised. Stop
the car, avoiding harsh braking or steering manoeuvres.
Repair using the dedicated kit (see the “Automatic
Fix&Go quick tyre repair kit” paragraph in the “In an
emergency” section) and contact an Abarth Dealership
as soon as possible.
Tyre pressure unsuitable for speed
Should travelling at a higher speed than 160 km/h be
required, inflate tyres to pressures values specified in
paragraph “Inflation pressures”.
If the TPMS system (where provided) detects that the
pressure of one or more tyres is unsuitable for the
current speed, the symbol will be shown on the display
together with the dedicated message (see paragraph
“Low tyre pressure” in this section) and it will stay on
until the car speed returns within the preset threshold.
IMPORTANT In this case, slow down immediately
because tyre overheating could compromise tyre
performance and durability beyond repair, and may even
make the tyre explode.
141-150 GPUNTO EVO Abarth GB 2ed 8-11-2010 14:43 Pagina 149

STARTING THE ENGINE
EMERGENCY STARTING
If the instrument panel warning light
Ystays on
permanently, contact an Abarth Dealership immediately.
IN AN EMERGENCY
In an emergency we recommend that you call the free-phone number found o\
n the Warranty Booklet. You can
also find the Abarth Dealership nearest to you on the web site www.fiat.\
com.
This procedure must be performed by
expert personnel because incorrect
actions could cause electrical discharge of
considerable intensity. Furthermore, battery
fluid is poisonous and corrosive: avoid contact
with skin and eyes. Keep naked flames away
from the battery. No smoking. Do not cause
sparks.
WARNING
IMPORTANT For the jump starting procedure, refer to
“Knowing your car” section, paragraph “Start&Stop
system”.
fig. 126F0U187Ab
151
KNOWING
YOUR VEHICLE
SAFETY
STARTING
AND DRIVING
WARNING LIGHTS
AND MESSAGES
IN AN
EMERGENCY
MAINTENANCE
AND CARE
TECHNICAL
SPECIFICATIONS
CONTENTS
JUMP STARTING fig. 126
If the battery is flat, the engine may be started using an
auxiliary battery with the same capacity or a little higher
than the flat one. It is advisable to contact an Abarth
Dealership to check/replace th e battery.
151-182 GPUNTO EVO Abarth GB 2ed 8-11-2010 14:44 Pagina 151

156
KNOWING
YOUR VEHICLE
SAFETY
STARTING
AND DRIVING
WARNING LIGHTS AND MESSAGES
IN AN
EMERGENCY
MAINTENANCE AND CARE
TECHNICAL
SPECIFICATIONS
CONTENTS
F0U133Abfig. 132
❒after driving for about 10 minutes, stop and check
the tyre pressure fig. 132 again; remember to put the
handbrake on;
Apply the adhesive label in a position
clearly visible by the driver as a reminder
that the tyre has been treated with the quick
repair kit. Drive carefully, particularly on bends.
Do not exceed 80 km/h. Do not accelerate and
brake suddenly.
WARNING
F0U132Abfig. 131
❒if in this case a pressure of at least 1.8 bar is not
reached within five minutes of switching on the
compressor, do not continue driving because the tyre
is too damaged and the hold cannot be guaranteed
using the kit. Contact an Abarth Dealership;
❒if the tyre reaches the pressure specified in the
“Inflation pressure” paragraph in the “Technical
Specifications” chapter, start driving immediately;
151-182 GPUNTO EVO Abarth GB 2ed 8-11-2010 14:45 Pagina 156

188
KNOWING
YOUR VEHICLE
SAFETY
STARTING
AND DRIVING
WARNING LIGHTS AND MESSAGES
IN AN
EMERGENCY
MAINTENANCE AND CARE
TECHNICAL
SPECIFICATIONS
CONTENTS
F0U171Abfig. 167
ENGINE OIL fig. 167
Check the oil level a few minutes (about five) after the
engine has stopped, with the car parked on level ground.
Check that the level is within the MIN and MAX marks
on the dipstick B.
The range between the MIN. and MAX. marks
corresponds to about 1 litre of oil.
If the oil level is near or under the MIN line, add oil
through the filler A until it reaches the MAX line.
The oil level should never exceed the MAX line. ENGINE OIL CONSUMPTION
The maximum engine oil consumption is usually 400
grams every 1000 km.
When the car is new, the engine needs to run in,
therefore the engine oil consumption can only be
considered stabilised after the first 5,000 - 6,000 km.
IMPORTANT The oil consumption depends on driving
style and the car usage conditions.
IMPORTANT After adding or changing the oil, let the
engine run for a few seconds and wait a few minutes
after switching it off before checking the level.
When the engine is hot, take care when
working inside the engine compartment
to avoid burns. Remember that when the engine
is hot, the fan may operate: danger of injury.
Pay attention to scarves, ties and other loose
fitting garments: they may get caught by moving
components.
WARNING
Do not add any oil with different
specifications to those of the existing
engine oil.
183-204 PUNTO Abarth GB 1ed 8-02-2012 13:24 Pagina 188

196
F0U175Abfig. 171
KNOWING
YOUR VEHICLE
SAFETY
STARTING
AND DRIVING
WARNING LIGHTS AND MESSAGES
IN AN
EMERGENCY
MAINTENANCE AND CARE
TECHNICAL
SPECIFICATIONS
CONTENTSRemember that road holding also
depends on the correct tyre inflation.
WARNING
If the pressure is too low the tyre
overheats and this can cause it serious
damage.
WARNING
Do not cross switch the tyres, moving
them from the right of the car to the left
and vice versa.
Never submit alloy rims to repainting
treatments requiring the use of temperatures
exceeding 150°C.
The mechanical properties of the wheels could
be impaired.
WARNING
❒check the tyres regularly for cuts on the sides, swelling
or irregular tread wear;. Contact an Abarth Dealership
if required;
❒avoid overloading the car when travelling: this may
cause serious damage to the wheels and tyres;
❒if a tyre is punctured, stop the vehicle immediately and
change it to avoid damage to the tyre, the rim, the
suspensions and the steering system;
❒a tyre will age even if it is not used much. Cracks in the
tread and on the sidewalls are a sign of ageing. Have
the tyres checked by skilled personnel if they have
been fitted for longer than six years. Also remember
to check the space-saver wheel very carefully;
❒in case of replacement, always fit new tyres, avoiding
those with an unknown origin;
❒if a tyre is replaced, also change the inflation valve;
❒to allow even wear between the front and rear tyres,
it is advisable to change them over every 10-15
thousand kilometres, keeping them on the same side
of the car so as not to reverse the direction of
rotation.
183-204 PUNTO Abarth GB 1ed 8-02-2012 13:25 Pagina 196

202
KNOWING
YOUR VEHICLE
SAFETY
STARTING
AND DRIVING
WARNING LIGHTS AND MESSAGES
IN AN
EMERGENCY
MAINTENANCE AND CARE
TECHNICAL
SPECIFICATIONS
CONTENTS
INTERIORS
Periodically check that water is not trapped under the
mats (due to water dripping off shoes, umbrellas, etc.)
which could cause oxidisation of the sheet metal.
Glasses
To clean glasses, use specific window cleaner products.
Also use clean cloths to avoid scratching the glass or
altering the transparency.
IMPORTANT Wipe the rear window inside gently with
a cloth in the direction of the filaments to avoid
damaging the heating device.
Engine compartment
Wash the engine compartment thoroughly at the end of
every winter. Be careful not to direct the jet of water
onto electronic control units. Adequately protect the
upper air vents to prevent damage to the windscreen
wiper motor. Have this operation performed at a
specialised workshop.
IMPORTANT The washing should take place with the
engine cold and the ignition key in the STOP position.
After the washing operation, make sure that the various
protections (e.g. rubber caps and guards) have not been
removed or damaged.
Front headlights
IMPORTANT Never use aromatic substances (e.g.: petrol)
or ketenes (e.g.: acetone) for cleaning front headlight plastic
lens.
Never use flammable products, such as
petrol ether or rectified petrol to clean
the inside of the car. The electrostatic charges
which are generated by rubbing during the
cleaning operation may cause a fire.
WARNING
Do not keep aerosol cylinders in the
vehicle: risk of bursting. Aerosol cylinders
must not be exposed to a temperature
exceeding 50°C. When the car is exposed to
sunlight, the internal temperature can greatly
exceed this value.
WARNING
183-204 PUNTO Abarth GB 1ed 8-02-2012 13:25 Pagina 202

RADIO
245
PRESET BUTTONS
The buttons numbered from 1 to 6 are used to set the
following preselections:
❒18 in the FM band (6 in FM1, 6 in FM2, 6 in FMT or
“FMA” on some versions);
❒ 12 in the MW band (6 in MW1, 6 in MW2).
To listen to a preset station, select the desired frequency
band and then press the corresponding preset button
briefly (from 1 to 6).
By pressing the preset button for more than 2 seconds,
the tuned station will be stored. The storing phase is
confirmed by a beep.
STORING THE LAST STATION LISTENED TO
The radio automatically stores the last station that was
selected for each reception band, that is then tuned into
when the radio is turned on or when the reception band
is changed. AUTOMATIC TUNING
Briefly press the ¯
or ˙button to start the automatic
tuning search for the next station that can be received in
the selected direction.
If the button ¯ or ˙is pressed for longer, the rapid
search is started. When the button is released, the tuner
will stop on the next station that can be received.
If the TA function (traffic news) is on, the tuner searches
only for stations that broadcast traffic news.
MANUAL TUNING
This is used to manually search for stations in the
preselected band.
Select the desired frequency band and then press the
button ▲or ▼briefly and repeatedly to start the search
in the desired direction.
If the button ▲ or ▼is pressed longer, the rapid search
starts and then stops when the button is released.
221-258 GPUNTO EVO Abarth GB 2ed 8-11-2010 14:47 Pagina 245

RADIO
250
DISPLAY INFORMATION
When the CD player is in operation, information
appears on the display with the following meanings:
❒“CD Track 5”: indicates the CD track number;
❒ “03:42”: indicates the time elapsed since the start of
the track (if the relevant Menu function is activated).
TRACK SELECTION (forward/backward)
Briefly press the ¯ button to play the previous CD track
and the ˙ button to play the next track. The tracks are
selected cyclically: the first track is selected after the last
track and vice versa.
If the track has been played for more than 3 seconds,
pressing the ¯button will cause the track to be started
again from the beginning. In this case, if you want to play
the previous track, press the button twice in succession. FAST FORWARD/REWIND THROUGH
TRACKS
Keep the button
˙pressed down to fast forward the
selected track and keep the button ¯pressed down to
fast rewind the track. The fast forward/rewind will stop
once the button is released.
PAUSE FUNCTION
To pause the CD player, press the button MUTE. The
text “CD Pause” appears on the display.
To resume listening to the track, press the button MUTE
again.
If another audio source is selected, the pause function is
deactivated.
221-258 GPUNTO EVO Abarth GB 2ed 8-11-2010 14:47 Pagina 250

261
KNOWING
YOUR VEHICLE
SAFETY
STARTING
AND DRIVING
WARNING LIGHTS
AND MESSAGES
IN AN
EMERGENCY
MAINTENANCE
AND CARE
TECHNICAL
SPECIFICATIONS
CONTENTS
Engine compartment – checking le vels ......................... 187
– opening/closing the bonnet .... 81
– washing ..................................... 202
Engine coolant temperature gauge ..................... 15
Engine coolant – checking levels and
topping up .................................... 189
– specifications ............................ 218
– temperature gauge and
warning lig ht ................................ 15
Engine immobiliser (Fiat CODE) ................................ 4
Engine mark ing .............................. 206
Engine oil – checking levels and
topping up .................................... 188
– consumpt ion ............................ 188
– technical specifications .......... 217
Engine start ing ............................... 131
– bump starting ........................... 152
– emergency starting
(of engine) .................................... 151
– how to warm up the engine
after it has just started .............. 132
– ignition switch ......................... 11
– jump starting ............................ 151
– stopping the engine ................ 133 Engine
– engine immobiliser (Fiat CODE) 4
– how to warm up the engine
after it has just started .............. 132
– identification c odes ................207
– marking ..................................... 206
– stopping the engine ................ 133
– technical specifications .......... 207
Environment (protec tion) ........... 108
EOBD (system) ............................. 92
ESP (system) .................................. 88
External lights (switching on) ..... 49
"e-GSI" system (Gear Shift Indicator) ................ 103
Fiat CODE .................................... 4
Fix&Go Automatic (rapid tyre re pair kit) ................ 152
Flashing (main beams) .................. 50
Fluids (specifications) ......... 217-218
Fluids and lubricants – refuelling ................................... 216
– specifications ..................217-218
Fog lights – bulb replace ment .................... 164
– Cornering Ligh ts function ..... 51
– switching on ............................. 58
Dipped beam headlights
– bulb replace ment .................... 162
– switching on ............................. 49
– switching on ............................. 50
Direction Indicators – front bulb repla cement .......... 163
– rear bulb repla cement ........... 165
– side bulb replacement ............ 164
– switching on ............................. 50
Document holder pocket ........... 66
Door po ckets ................................ 63
Doors .............................................. 71 – central locking ......................... 71
– Dead Lock ................................ 73
– door unlocking from
the outside ................................... 72
– locking the doors from
the outside ................................... 71
– locking/unlocking from
the insi de ...................................... 72
– pockets ..................................... 63
DSS (Driving Sport Switch) (car dynamic control system) ... 96
Electrical/electronic devices
(important notes for
installation) .................................. 106
Engine c odes .................................. 207
259-266 PUNTO Abarth GB 1ed 24-02-2012 10:08 Pagina 261