ECU ACURA CSX 2006 Service Repair Manual





14-248Automatic Transmission
Transmission Installation (cont’d)
E
12x1.25mm
59 N·m
(6.0 kgf·m, 43 lbf·ft)
D
12x1.25mm
59N·m(6.0kgf·m,43lbf·ft)C
12x1.25mm
59 N·m
(6.0 kgf·m, 43 lbf·ft)
A
B A
B C
B A
07AAK-SNAA120
8x1.25mm
26 N·m (2.7 kgf·m, 20 lbf·ft)
33. Install both of the lower arms (A) to the ball joints
(B), and loosely install new mounting nuts and
bolts.
34. Tighten the nuts and bolts to 59 N·m (6.0 kgf·m, 43 lbf·ft) in the following order; (C), then (D), then
(E).
35. Install the exhaust pipe rubber mount. 36. Connect the ATF cooler hose (A) to the ATF cooler
(B), and secure the hose with the clip (C) (see page
14-253).
37. Remove the engine hanger plate (07AAK- SNAA120) and the bolt (A), and install the air
cleaner housing mounting bracket (B) on the
engine.
38. Remove the engine hanger.
Replace. Replace.Replace.
08/08/21 14:48:47 61SNR030_140_0250
ProCarManuals.com
DYNOMITE -2009-




14-249
A
B
AB
C
C
A
B
6x1.0mm
12 N·m (1.2 kgf·m, 8.7 lbf·ft) A
B C
A B
C
D E
D E
39. Connect the ATF cooler hoses (A) to the ATF cooler
lines (B), and secure the hoses with the clips (C)
(see page 14-253).
40. Secure the harness clamp bracket (A) on the transmission hanger (B) with the bolt. 41. Install the water hose (A) to its clamp (B) at the
mark (C).
42. Connect the shift solenoid wire harness connector (A), the A/T clutch pressure control solenoid valve
B connector (B), and the A/T clutch pressure control
solenoid valve C connector (C), and install the
harness clamps (D) on the clamp brackets (E).
(cont’d)
08/08/21 14:48:48 61SNR030_140_0251
ProCarManuals.com
DYNOMITE -2009-

µµ
µµ µ µ
µµ
µµ
Î
(#'



 )
Exploded View
Point Distance from Hose End to Clip (L) Hose End Contact Point
14-253
ATF Cooler Hose Replacement
L
G
H
E
White paint markA
Pink paint mark
B
Pink paint mark
C
White paint mark
D
Pink paint mark
F
White paint mark
NOTE: When installing the hose clamps, make sure not to interfere to the surr ounding parts.
1. Install the ATF cooler hoses over the ATF cooler lines with the clips at appropriate points in reference to the following list.
A 6 8 mm (0.24 0.31 in.) BulgeB
C 5 7 mm (0.20 0.28 in.) ATF filter from 10 12 mm (0.40 0.47 in.)
D E 2 4 mm (0.08 0.16 in.) White paint lineF 2 4 mm (0.08 0.16 in.) Bulge
2. Secure the ATF cooler hose with the clamp (G) at the white paint line (H).
3. Refill the transmission with ATF to the proper level (see page 14-232).
08/08/21 14:48:50 61SNR030_140_0255
ProCarManuals.com
DYNOMITE -2009-




(#'




 )
14-254 Automatic Transmission
Shift Lever Removal
A
A
B C
A
B
1. Remove the center console (see page 20-92).
2. Move the shift lever to R.
3. Pry the socket holder lock (A) up using a
screwdriver.
4. Remove the nut securing the shift cable end. 5. Rotate the socket holder retainer (A)
counterclockwise, push it against the socket holder
bracket (B), then slide the socket holder to remove
the shift cable (C) from the socket holder bracket.
6. Disconnect the shift lock solenoid connector (A) and the park pin switch/A/T gear position indicator
panel light connector (B).
7. Remove the shift lever assembly.
08/08/21 14:48:51 61SNR030_140_0256
ProCarManuals.com
DYNOMITE -2009-




(#'





 )
14-257
Shift Cable Replacement
A A
B C
A BC
D
E
F
1. Raise the vehicle on a lift, or apply the parking
brake, block the rear wheels, and raise the front of
the vehicle. Make sure it is securely supported.
2. Move the shift lever to R.
3. Remove the center console (see page 20-92).
4. Pry the socket holder lock (A) up using a screwdriver.
5. Remove the nut securing the shift cable end. 6. Rotate the socket holder retainer (A)
counterclockwise, push it against the socket holder
bracket (B), then slide the socket holder to remove
the shift cable (C) from the socket holder bracket.
7. Remove the three bolts securing the shift cable holder (A), then remove the shift cable cover (B).
8. Pry up the lock tab of the lock washer (C), and remove the lock bolt (D) and the lock washer, then
separate the control lever (E) from the selector
control shaft (F). Do not bend the shift cable
excessively.
(cont’d)
08/08/21 14:48:52 61SNR030_140_0259
ProCarManuals.com
DYNOMITE -2009-

Î
14-258Automatic Transmission
Shift Cable Replacement (cont’d)
6x1.0mm
9.8 N·m (1.0 kgf·m, 7.2 lbf·ft)
6x1.0mm
9.8 N·m
(1.0 kgf·m, 7.2 lbf·ft)A
B C
D
6x1.0mm
12 N·m
(1.2 kgf·m, 8.7 lbf·ft)6x1.0mm
9.8 N·m
(1.0 kgf·m,
7.2 lbf·ft)
D
6x1.0mm
14 N·m
(1.4 kgf·m,
10 lbf·ft)A
B
E
F
C
9. Remove the nuts securing the shift cable bracket
(A) and the grommet (B).
10. Remove the shift cable grommet, and pull out the shift cable (C).
11. Insert a new shift cable through the grommet hole (D), and install the grommet in its hole. Do not bend
the shift cable excessively.
12. Secure the shift cable bracket and the grommet with the nuts.
13. Make sure that the transmission is in the R position at the selector control shaft. 14. Install the control lever (A) over the selector control
shaft (B).
15. Secure the control lever with a new lock washer (C) and the lock bolt (D), then bend the lock tab of the
lock washer against the bolt head.
16. Install the shift cable cover (E), and install the shift cable holder (F) on the cover.
17. Install the shift cable on the shift lever, and adjust the cable (see step 5 on page 14-259).
Replace.
08/08/21 14:48:53 61SNR030_140_0260
ProCarManuals.com
DYNOMITE -2009-




(#'





")
14-259
Shift Cable Adjustment
A A
B C
A
B C
1. Remove the center console (see page 20-92).
2. Pry the socket holder lock (A) up using a
screwdriver.
3. Remove the nut securing the shift cable end. 4. Rotate the socket holder retainer (A)
counterclockwise, push it against the socket holder
bracket (B), then slide the socket holder to remove
the shift cable (C) from the socket holder bracket.
5. While holding the socket holder (A), rotate the socket holder retainer (B) fully counterclockwise,
and press in the socket holder lock (C) between the
socket holder and the socket holder retainer
enough.
(cont’d)
08/08/21 14:48:54 61SNR030_140_0261
ProCarManuals.com
DYNOMITE -2009-


Î

14-260Automatic Transmission
Shift Cable Adjustment (cont’d)
A
B
C
A B
C B
A
6. Align the socket holder (A) with the slot (B) in the socket holder bracket (C), then slide the socket
holder into the socket holder bracket.
7. Rotate the socket holder retainer (A) clockwise, and push the socket holder lock (B). Rotate the holder
retainer counterclockwise until the retainer stops at
the stop (C) of the socket holder lock to secure the
shift cable. 8. Push the shift cable (A) until it stops, then release it.
Pull the shift cable back one step so that the shift
position is in R. Do not hold the shift cable guide (B)
to adjust the shift cable.
9. Turn the ignition switch to ON (II), and check that the R position indicator comes on.
10. Turn the ignition switch to LOCK (0).
08/08/21 14:48:55 61SNR030_140_0262
ProCarManuals.com
DYNOMITE -2009-





14-261
A
B
A
B
C
D E
Properly Installed:
Improperly Installed: A
B
11. Place the shift lever in R, then insert a 6.0 mm
(0.24 in.) pin (A) into the positioning holes (B) on
the shift lever bracket, through the positioning hole
on the shift lever, and into the positioning hole on
thebracket.Useonlya6.0mmpinthatisfreeof
burrs.
12. Check that the shift lever is secured in R. 13. Install the shift cable end (A) over the mounting
stud (B) by aligning its square hole (C) with the
square fitting (D) at the bottom of the stud. Do not
install the shift cable by holding the shift cable
guide (E).
14. Check that the shift cable end (A) is properly installed on the mounting stud (B).
15. If improperly installed, align the square fitting with the square hole by rotating the mounting stud.
(cont’d)
Cable end rides on the bottom of the mounting stud.
08/08/21 14:48:55 61SNR030_140_0263
ProCarManuals.com
DYNOMITE -2009-


Î

(#'




)
µ
Transmission Range Switch Subharness
Connector
14-265
Transmission Range Switch Test
A Connector Terminal/Signal
25
134
687910
P
R
N
D
S
Posi-
tion
6x1.0mm
12 N·m (1.2 kgf·m, 8.7 lbf·ft)
ATP
NP
ATP
FWD
GND
ATP
RVS
ATP
D ATP
R ATP
P ATP
SATP
N
1. Remove the intake air duct (see page 11-348) and
the air cleaner assembly (see page 11-345).
2. Disconnect the transmission range switch subharness connector (A).
3. Check for continuity between the terminals at the harness connector. There should be continuity
between the terminals in the following table for
each switch position. 4. Transmission range switch test has completed if
the test results are OK, go to step 12. If there is no
continuity between any terminals, go to step 5.
5. Raise the vehicle on a lift, or apply the parking brake, block the rear wheels, and raise the front of
the vehicle. Make sure it is securely supported.
6. Remove the transmission range switch cover.
(cont’d)
Terminal side of
male terminals
08/08/21 14:49:01 61SNR030_140_0267
ProCarManuals.com
DYNOMITE -2009-