ECU ACURA CSX 2006 Service Repair Manual


Î
20-11
Fastener Locations
:Screw,2
A
B
C
D D
A
A B
A
A
10. If necessary, remove the special screws, then separate the door cylinder (A) and the outer handle
protector (B). If the retainer (C) is damaged, release
the hooks (D), and replace it.
NOTE: If removed, the special screws must be
replaced.
11. While pulling the outer handle (A), remove the handle from the holes in the door panel. Take care
not to scratch the door. 12. Remove the rod fastener (A) from the outer handle
(B), then replace it with a new one.
13. Install the handle in the reverse order of removal, and note these items:
 Make sure the cylinder cable and each rod is connected securely.
 Make sure the door key cylinder/door locks operate properly.
 Make sure the door handle works properly.
 When reinstalling the door panel, make sure the
plastic cover is installed properly and sealed
around its outside perimeter to seal out water.
 Check for water leaks (see step 9 on page 20-29).
Replace.
08/08/21 14:59:00 61SNR030_200_0013
ProCarManuals.com
DYNOMITE -2009-



(#'


 )
20-12 Doors
Front Door Latch Replacement
Fastener Location
:Bolt,1
6x1.0mm
8N·m
(0.8 kgf·m, 6 lbf·ft) A
B Fastener Locations
:Screw,3
D:Screw,1 E
A
B C
D
E
F G
D D
6x1.0mm
6N·m
(0.6 kgf·m,
4lbf·ft)
6x1.0mm
6N·m
(0.6 kgf·m,
4lbf·ft)
NOTE: Put on gloves to protect your hands. 1. Raise the glass fully.
2. Remove the door panel and inner handle (see page 20-7).
3. Remove the plastic cover, as needed (see step 4 on page 20-9).
4. Detach the rod fastener (see step 5 on page 20-9).
5. Disconnect the outer handle rod from the outer handle (see step 6 on page 20-10).
6. Disconnect the cylinder cable from the latch (see step 7 on page 20-10).
7. Pull the glass run channel (A) away as needed, and remove the bolt, then remove the center lower
channel (B) by pulling it downward. 8. Detach the latch cable (A) and the inner handle
cable (B) from the holder (C), then remove the
screws (D, E) securing the latch (F), then remove
the latch through the hole in the door. Take care not
to bend the outer handle rod (G), the latch cable, or
the inner handle cable.
08/08/21 14:59:01 61SNR030_200_0014
ProCarManuals.com
DYNOMITE -2009-



20-13
Fastener Location:Screw,1
AB
A
A
B
B
C
9. Remove the screw, then remove the latch protector
(A) by releasing the hook (B).
10. Disconnect the latch cable (A) and the inner handle cable (B) from the latch (C). 11. Install the latch in the reverse order of removal, and
note these items:
 Make sure the actuator connector is plugged in properly and each rod is connected securely.
 Make sure the door locks and opens properly.
 When reinstalling the door panel, make sure the
plastic cover is installed properly and sealed
around its outside perimeter to seal out water.
 Check for water leaks (see step 9 on page 20-29).
08/08/21 14:59:01 61SNR030_200_0015
ProCarManuals.com
DYNOMITE -2009-




(#'


 )
20-1620-16 Doors
Front Door Glass Outer
Weatherstrip Replacement (cont’d)
Front Door Weatherstrip
Replacement
A
B
A
Fastener Locations :Bolt,1
A :Clip,14
B
:Clip,2
C
:Clip,1
D
B
C
AC
F
E D
8x1.25mm
29 N·m
(3.0 kgf·m, 22 lbf·ft) E
(White)
(Black) (Left: Pink
Right: Blue)
4. Slide the front door glass outer weatherstrip (A)
forward.
5. Twist the front door glass outer weatherstrip (A) to pull the rear hook (B) out from the inside of the
door, then remove the weatherstrip.
6. Push the clip portions of new front door glass outer weatherstrip into place securely. NOTE:
 Put on gloves to protect your hands.
 Take care not to scratch the door.
 Remove the clips with a clip remover.
1. At the A-pillar, remove the door checker mounting
bolt (A).
2. Detach the clips (B, C, D), then remove the door weatherstrip (E).
3. Install the weatherstrip in the reverse order of removal, and note these items:
 If the clips are damaged or stress-whitened, replace them with new ones.
 Make sure the weatherstrip is installed in the holder (F) securely.
 Apply medium strength liquid thread lock to door checker mounting bolt before installation.
 When reinstalling the door panel, make sure the
plastic cover is installed properly and sealed
around its outside perimeter to seal out water.
 Check for water leaks (see step 9 on page 20-29).
08/08/21 14:59:03 61SNR030_200_0018
ProCarManuals.com
DYNOMITE -2009-




(#'


 )
20-1620-16 Doors
Front Door Glass Outer
Weatherstrip Replacement (cont’d)
Front Door Weatherstrip
Replacement
A
B
A
Fastener Locations :Bolt,1
A :Clip,14
B
:Clip,2
C
:Clip,1
D
B
C
AC
F
E D
8x1.25mm
29 N·m
(3.0 kgf·m, 22 lbf·ft) E
(White)
(Black) (Left: Pink
Right: Blue)
4. Slide the front door glass outer weatherstrip (A)
forward.
5. Twist the front door glass outer weatherstrip (A) to pull the rear hook (B) out from the inside of the
door, then remove the weatherstrip.
6. Push the clip portions of new front door glass outer weatherstrip into place securely. NOTE:
 Put on gloves to protect your hands.
 Take care not to scratch the door.
 Remove the clips with a clip remover.
1. At the A-pillar, remove the door checker mounting
bolt (A).
2. Detach the clips (B, C, D), then remove the door weatherstrip (E).
3. Install the weatherstrip in the reverse order of removal, and note these items:
 If the clips are damaged or stress-whitened, replace them with new ones.
 Make sure the weatherstrip is installed in the holder (F) securely.
 Apply medium strength liquid thread lock to door checker mounting bolt before installation.
 When reinstalling the door panel, make sure the
plastic cover is installed properly and sealed
around its outside perimeter to seal out water.
 Check for water leaks (see step 9 on page 20-29).
08/08/21 14:59:03 61SNR030_200_0018
ProCarManuals.com
DYNOMITE -2009-





(#'



 )
Special Tools Required
20-17
Rear Door Panel Removal/Installation
A
B
C
Fastener Locations :Screw,1 :Clip,1
AFa

stener Location
:Clip,1
A B
C
D
B
A
Fastener Location :Screw,1
KTC trim tool set SOJATP2014
NOTE: Use the appropriate tool from the KTC trim tool
s
et to avoid damage when removing components.
1. Raise the glass fully.
2. Pry out on the rear portion of the inner handle cap (A) with the appropriate trim tool, then release the
hooks (B, C).
3. Remove the screw and clip securing the inner handle (A). 4

. Remove the power window switch panel (A).
–1 Pry up on the rear edge of the switch panel with the appropriate trim tool, then release the
rear clip.
–2 Pull out along the edge of the panel to release the hooks (B).
–3 Pull the switch panel rearward to release the front hook (C).
–4 Disconnect the power window switch connector (D).
5. Remove the screw.
(cont’d)
08/08/21 14:59:04 61SNR030_200_0019
ProCarManuals.com
DYNOMITE -2009-



(#'



 )
20-1920-19
Rear Door Outer Handle
Replacement
A B
62 mm (2.44 in.) A
B
C
D C
A
10. Install the door panel in the r everse order of
removal, and note these items:
 If the clips are damaged or stress-whitened, replace them with new ones.
 Replace any damaged cable fasteners with new ones.
 The latch cable (A) should be fixed to the cable fastener (B) with the latch in lock position.
 Make sure the connector is plugged in properly, and the cables are connected securely.
 Make sure the window and power door lock operate properly. NOTE: Put on gloves to protect your hands.
1. Raise the glass fully.
2. Remove the door panel (see page 20-17).
3. Detach the harness clip (A), and disconnect the power door lock actuator connector (B).
4. Remove the plug caps (C), then remove the plastic cover (D), as needed.
5. Remove the latch mounting screws, then lower the latch (see step 4 on page 20-21).
6. Detach the rod fastener (A).
(cont’d)
08/08/21 14:59:06 61SNR030_200_0021
ProCarManuals.com
DYNOMITE -2009-



(#'



 )
20-1920-19
Rear Door Outer Handle
Replacement
A B
62 mm (2.44 in.) A
B
C
D C
A
10. Install the door panel in the r everse order of
removal, and note these items:
 If the clips are damaged or stress-whitened, replace them with new ones.
 Replace any damaged cable fasteners with new ones.
 The latch cable (A) should be fixed to the cable fastener (B) with the latch in lock position.
 Make sure the connector is plugged in properly, and the cables are connected securely.
 Make sure the window and power door lock operate properly. NOTE: Put on gloves to protect your hands.
1. Raise the glass fully.
2. Remove the door panel (see page 20-17).
3. Detach the harness clip (A), and disconnect the power door lock actuator connector (B).
4. Remove the plug caps (C), then remove the plastic cover (D), as needed.
5. Remove the latch mounting screws, then lower the latch (see step 4 on page 20-21).
6. Detach the rod fastener (A).
(cont’d)
08/08/21 14:59:06 61SNR030_200_0021
ProCarManuals.com
DYNOMITE -2009-



Î
20-20 Doors
Rear Door Outer Handle Replacement (cont’d)
A
B
C
Fastener Locations :Bolt,2
6x1.0mm
9.8 N·m
(1.0 kgf·m,
7.2 lbf·ft) B
C
A
A
A
B
A
B A
7. Disconnect the outer handle rod (A) with a clip
remover (B) from the outer handle (C).
8. Remove the maintenance seal (A). Remove the bolts securing the outer handle protector (B), then
remove the protector by releasing the hook (C). 9. While pulling the outer handle (A), remove the
handle from the holes in the door panel. Take care
not to scratch the door.
10. Remove the rod fastener (A) from the outer handle (B), then replace it with a new one.
Replace.
08/08/21 14:59:07 61SNR030_200_0022
ProCarManuals.com
DYNOMITE -2009-


(#'


 )
20-2120-21
Rear Door Latch Replacement
Fastener Locations :Screw,3
A:Screw,1 B
A
A
A
6x1.0mm
6N·m
(0.6 kgf·m, 4 lbf·ft) 6x1.0mm
6N·m
(0.6 kgf·m, 4 lbf·ft)C
B
11. Install the handle in the reverse order of removal, and note these items:
 Make sure the door locks and opens properly.
 When reinstalling the door panel, make sure the
plastic cover is installed properly and sealed
around its outside perimeter to seal out water.
 Check for water leaks (see step 9 on page 20-29). NOTE: Put on gloves to protect your hands.
1. Raise the glass fully.
2. Remove the door panel (see page 20-17).
3. Remove the plastic cover, as needed (see step 4 on page 20-19).
4. Remove the screws (A, B) securing the latch (C), then lower it.
5. Detach the rod fastener (see step 6 on page 20-19).
6. Disconnect the outer handle rod from the outer handle (see step 7 on page 20-20).
(cont’d)
08/08/21 14:59:07 61SNR030_200_0023
ProCarManuals.com
DYNOMITE -2009-