ECU ACURA CSX 2006 Service Repair Manual



20-68Interior Trim
Trim Removal/Installation - Door Areas (cont’d)
C
Fastener Locations
: Clip, 2(White)
B D
E
D
D
E
A E
A
B
A
2. Pull the seat hook knob (A) while pushing down on the rear seat cushion (B) to release the hook (C).
While pulling the cushion up, detach the clips and
remove the rear door sill trim (D) from the rear
door opening seal (E).
3. Pull out the rear door opening seal (A) from the trim hooks (B) and around the rear door opening
flange, then remove the seal. 4. Install the trim in the reverse order of removal, and
note these items:
 If the clips are damaged or stress-whitened, replace them with new ones.
 Push the clips and the hooks into place securely.
08/08/21 15:01:30 61SNR030_200_0070
ProCarManuals.com
DYNOMITE -2009-


(#' )

S

pecial Tools RequiredA-Pillar Trim
20-69
Trim Removal/Installation - Pillar Areas
A
B C
D E A
C
D
E
F A
B
KTC trim tool set SOJATP2014
SRS components are located in this area. Review the
S
RS component locations (see page 24-11) and the
precautions and procedures (see page 24-13) before
doing repairs or service.
NOTE:  Follow the A-pillar trim installation procedure carefully; improper installation could cause the side
curtain airbag to deploy improperly and possibly
cause injury.
 Put on gloves to protect your hands.
 Use the appropriate tool from the KTC trim tool set to avoid damage when removing components.
 Take care not to scratch the trim and panels.
 The upper clip in the A-pillar trim (A) consists of a grommet (B) and a pin (C). The grommet expanded
with the pin secures it to the body panel (D). The
projections (E) on the pin are broken during removal,
so the clip must be replaced with a new one when the
trim is reinstalled. 1

. Pull the door opening seal away from the A-p
illar
as needed (see step 4 on page 20-66).
2. Hit the upper clip in the A-p illar trim (A) with a
rubber mallet. The clip is under the ‘‘SIDE CURTAIN
AIRBAG’’ mark (B). Hitting the clip breaks the
projections (C) on the pin (D) and pushes it into the
grommet (E) on the body (F).
NOTE: The upper clip must be replaced with a new
one when the A-pillar trim is reinstalled.
(cont’d)
08/08/21 15:01:30 61SNR030_200_0071
ProCarManuals.com
DYNOMITE -2009-


Slider engagement with shoulder anchor adjuster
20-74 Interior Trim
Trim Removal/Installation - Pillar Areas (cont’d)
A
BC
D E
F A
F G
H IB
9. Install the trim in the reverse order of removal, and
note these items:
 If the clips (A) are damaged or stress-whitened, replace them with new ones.
 If the side curtain airbag has deployed, replace the B-pillar upper and lower trim and all clips on
the trim with new ones (see page 24-185).
 To prevent the side curtain airbags from deploying improperly and possibly causing
injury, inspect the trim and replace it if it has any
of the following damage:
– Any cracks or deformations in the B-pillar upper trim (B) and the upper hooks (C), and
any stress-whitening in the upper part of the
trim
– Any cracks or deformations in the B-pillar lower trim (D), and any breakages in the part
(E) fitted with the B-pillar upper trim
– Any cracks or stress-whitening in the clips seating surface (F)
 Replace any damaged parts with new ones.
 Make sure the top of the trim overlaps with the headliner correctly (see page 24-187).
 Make sure the pin (G) on the front seat belt shoulder anchor adjuster (H) and the hole (I) on
the back of the slider are engaged when
installing the B-pillar upper trim.
 Make sure the trim hook is installed into the side curtain airbag B-pillar bracket securely.
 Push the clips and the hooks into place securely.
 Before installing the anchor bolt, make sure there are no twists or kinks in the seat belt.
08/08/21 15:01:33 61SNR030_200_0076
ProCarManuals.com
DYNOMITE -2009-


(#' )
S

pecial Tools RequiredC-Pillar Trim
20-75
A
D
B
C
E A
C D
E
F
A
B
KTC trim tool set SOJATP2014
SRS components are located in this area. Review the
S
RS component locations (see page 24-11) and the
precautions and procedures (see page 24-13) before
doing repairs or service.
NOTE:  Follow the C-pillar trim installation procedure carefully; improper installation could cause the side
curtain airbag to deploy improperly and possibly
cause injury.
 Put on gloves to protect your hands.
 Use the appropriate tool from the KTC trim tool set to avoid damage when removing components.
 Take care not to scratch the trim and panels.
 The front clip in the C-pillar trim (A) consists of a grommet (B) and a pin (C). The grommet expanded
with the pin secures it to the body panel (D). The
projections (E) on the pin are broken during removal,
so the clip must be replaced with a new one when the
trim is reinstalled. 1.

Remove these items:
 Rear seat cushion (see page 20-133)
 Rear seat side bolster (see page 20-134)
 Rear door opening seal, as needed (see step 3 on page 20-68)
2. Fold the seat-back forward.
3. Hit the front clip in the C-pillar trim (A) with a rubber mallet. The clip is near the triangle mark (B).
Hitting the clip breaks the projections (C) on the pin
(D) and pushes it into the grommet (E) on the body
(F).
NOTE: The clip must be replaced with a new one
when the C-pillar trim is reinstalled.
(cont’d)
08/08/21 15:01:34 61SNR030_200_0077
ProCarManuals.com
DYNOMITE -2009-


20-79
AB
C
A
B
C Fastener Locations
: Clip, 4(White)
A
B
C D
FG
E
B
D G
A
D
E G
4. Release the hook (A) by pushing in on the detents
(B) on the rear shelf (C), then lift up on the front
edge of the shelf at each detent. 5. Lift the rear shelf (A) upward to detach the
remaining four clips, and release the hooks (B) of
the high mount brake light from the rear shelf.
Release the pin (C) from the holes on the body.
6. Release each anchor rod (D) out through the hole in the rear shelf, and pull both rear seat belts (E) and
rear center seat belt (F) out through the slits (G) in
the rear shelf.
7. Install the shelf in the reverse order of removal, and note these items:
 If the clips are damaged or stress-whitened, replace them with new ones.
 When installing the rear shelf, slip the rear seat belt through the slit and the rear center seat belt
into the lid opening in the rear shelf.
 Push the clips and the hooks into place securely.
 Make sure the high mount brake light connector is connected securely.
08/08/21 15:01:36 61SNR030_200_0081
ProCarManuals.com
DYNOMITE -2009-


20-81
Fastener Locations
:Clip,3
A:Clip,2 B
A B
C
D E
C
A
A
B A
6. Remove the clips (A, B), then remove the trunk side
trim panel (C). Release the wire harness (D) from
the slit (E) in the trim panel. 7. If necessary, remove the trunk tool box (A).
8. Install the trim in the reverse order of removal, and
note these items:
 If the clips are damaged or stress-whitened, replace them with new ones.
 Push the clips into place securely.
08/08/21 15:01:37 61SNR030_200_0083
ProCarManuals.com
DYNOMITE -2009-




20-83
A
AB A
B C
A
B C
A
3. Remove all of the clips (A) with a pair of pliers by pinching its hooks.
4. If the side curtain airbag has deployed, replace the grab handle with a new one.
5. If the side curtain airbag has not deployed, to prevent the side curtain airbags from deploying
improperly and possibly causing injury, inspect the
removed pieces and replace them if they have any
of the following damage:
 Any cracks or breakage in the grab handle (A).
 Any cracks or stress-whitening in the stoppers (B). 6. Install the clips (A) to the grab handle (B), then
install the stoppers (C) fully into the clips.
7. Position the grab handle (A) on the bracket (B), and push on the grab handle until the clips (C) snap into
place securely.
08/08/21 15:01:39 61SNR030_200_0085
ProCarManuals.com
DYNOMITE -2009-




20-85
A
B
B
A
B D
B
5x0.8mm
5N·m
(0.5 kgf·m,
4lbf·ft)
Fastener Locations
:Bolt,2
C
E
F
G A
B
C
A
Fastener Locations :Bolt,4
8x1.25mm
22 N·m
(2.2 kgf·m,
16 lbf·ft) A
6. Push the hook (A) with a flat-tip screwdriver
wrapped with protective tape, and turn the holder
(B) 90 °, then pull it out.
7. Remove the individual map light assembly (A). –1 Remove the lenses (B).
–2 Remove the bolts.
–3 If equipped, release the four tabs (C), then pullout the moonroof switch (D) or the navigation
microphone.
–4 Disconnect the front individual map light connector (E). If equipped, disconnect the
moonroof switch connector (F) and the
navigation microphone connector (G). 8. Without moonroof: Remove the driver’s dashboard
undercover (see page 20-104).
9. Detach the harness clips (A) from the A-pillar (B), and disconnect the roof wire harness connector (C).
10. Remove the center console (see page 20-92).
11. Slide both front seats all the way back, and recline the seat-backs fully.
12. Remove the bolts securing the parking brake base frame (A), and lay it down as needed.
(cont’d)
08/08/21 15:01:40 61SNR030_200_0087
ProCarManuals.com
DYNOMITE -2009-

Î
20-87
Fastener Locations:Bolt,1
A :Bolt,2
B
A
B C
B D
5x0.8mm
6N·m
(0.6 kgf·m, 4 lbf·ft)
5x0.8mm
6N·m
(0.6 kgf·m, 4 lbf·ft)
16. If necessary, remove the side curtain airbag mounting bolt (A) and grab handle bracket
mounting bolts (B), then remove the grab handle
bracket (C) from each side by releasing the hooks
(D). 17. Install the headliner in the reverse order of removal,
and note these items:
 If the side curtain airbag has deployed, replace the headliner and related parts with new ones
(see page 24-185).
 To prevent the side curtain airbags from deploying improperly and possibly causing
injury, inspect the removed pieces and replace
them if they have any of the following damage:
– Any crease or tears in the headliner (A)
– Any cracks or breakage in the grab handle (B)
– Any damages around the grab handle holes (C) or sunvisor holes in the headliner
– Any cracks in the sunvisor stay base (D)
– Any bends or cracks in the sunvisor stay shaft (E)
– Any cracks in the sunvisor base (F)
– Any cracks or breakage in the vanity mirror base (G)
– Any Velcro fasteners (H) and the clip bases (I) which have come off the headliner
 When installing the grab handle, push on the grab handle against the bracket (J) until the clips
(K) snap into place securely.
 If the clips are damaged or stress-whitened, replace them with new ones.
 Replace the removed cushion tape with new ones.
 Check that both sides of the headliner are securely attached to the trim.
 Make sure the headliner overlaps the trim pieces correctly (see page 24-187).
 When reinstalling the headliner through the front passenger’s door opening, be careful not to fold
or bend it. Also, be careful not to scratch the
body.
 Check for any DTCs that may have been set during repairs, and clear them.
 Do the battery terminal reconnection procedure (see page 22-68).
(cont’d)
08/08/21 15:01:41 61SNR030_200_0089
ProCarManuals.com
DYNOMITE -2009-


20-91
AB
C
C
10. Release the Velcro fastener (A), then pull the carpet (B) out from under the dashboard. 11. Pull the seat harnesses (C) out through the hole in
the carpet, then remove the carpet.
12. Install the carpet in the reverse order of removal, and note these items:
 Take care not to damage, wrinkle or twist the carpet.
 Make sure the seat harnesses and parking brake cables are routed correctly.
 If the clips are damaged or stress-whitened, replace them with new ones.
 Push the Velcro fasteners and the clips into place securely.
 Push the accelerator pedal hooks into place securely, and verify that the pedal is properly
fastened to the floor.
08/08/21 15:02:47 61SNR030_200_0093
ProCarManuals.com
DYNOMITE -2009-