ECU ACURA CSX 2006 Service Repair Manual


20-121
Fastener Locations
6x1.0mm
9.8 N·m
(1.0 kgf·m,
7.2 lbf·ft)
:Bolt,4
AB
C A
B
C A
(Black)
B
(White)
4. Remove the bolts, and release the seat cushion springs (A) from the hooks (B), then remove the
seat cushion frame (C).
5. Remove the front seat weight sensors (see page 24-207). 6. If necessary, remove the bushing (A, B) from the
seat cushion frame (C).
7. Install the new seat frame in the reverse order of removal, and note these items:
 Make sure the ODS unit connector is plugged in properly.
 If the clips are damaged or stress-whitened, replace them with new ones.
 Push the clips into place securely.
 Make sure the seat wiring harnesses are routed properly and are not pinched.
 Calibrate the ODS unit, if necessary (see page 24-27).
08/08/21 15:03:55 61SNR030_200_0123
ProCarManuals.com
DYNOMITE -2009-


(#'
 )
Driver’s Seat
20-122 Seats
Front Seat Frame Replacement (cont’d)
A
B
C
D
Fastener Locations
:Clip,3
A
E
Check the operation of the driver’s seat position sensor
after any of these actions (see page 24-29):
 Driver’s seat position sensor replacement
 Cover plate (front side of driver’s seat slide rail) replacement
NOTE:  Put on gloves to protect your hands.
 Apply oil to the pivot portions of the slide lock.
 Apply multipurpose grease to the sliding portions and pivot portions of the seat tracks.
 If the side airbag has deployed, replace the seat frame and related pieces with new ones (see page
24-185).
1. Remove the front seat (see page 20-118).
2. Remove these items:  Front seat-back cover/pad (see page 20-123)
 Front seat cushion cover/pad (see page 20-127)
 Driver’s seat position sensor (see page 24-211)
 Front seat belt buckle (see page 24-6) 3. Remove the clips, then remove the recline inner
covers (A), the outer upper rail cover (B), the inner
upper rail cover (C) and the module holder (D) from
the seat frame (E).
4. Install the new seat frame in the reverse order of removal, and note these items:
 Make sure the driver’s seat position sensor connector is plugged in properly.
 If the clips are damaged or stress-whitened, replace them with new ones.
 Push the clips into place securely.
 Make sure the seat wiring harnesses are routed properly and not pinched.
08/08/21 15:03:56 61SNR030_200_0124
ProCarManuals.com
DYNOMITE -2009-








20-126Seats
Front Seat-back Cover Replacement (cont’d)
A
B
A AA
A
A
A
B C
D
13. Remove the seat-back cover/pad (A) from the seatframe (B).
14. Pull back the edge of the seat-back cover all the way around, and release the clips (A), then remove
the seat-back cover. 15. Install the cover in the reverse order of removal,
and note these items:
 Reinitialize the ODS unit (see page 24-26).
 To prevent wrinkles when installing a seat-back cover, make sure the material is stretched evenly
over the pad before securing the clips, the hooks,
and the hook strips.
 Replace any clips (A) you removed with new ones.
 Before installing the side airbag (B), make sure the reinforcing cloth (C) is fixed on the seat-back
frame (D) securely.
 Make sure the side airbag harness, and the seat heater harness (some driver’s seat) or the ODS
unit subharness (passenger’s seat) are routed
properly.
08/08/21 15:03:59 61SNR030_200_0128
ProCarManuals.com
DYNOMITE -2009-






20-130Seats
Front Seat Cushion Cover Replacement (cont’d)
A
B
A
A
A
A A
12. Release the hooks (A) from under the seat cushion
(B).
13. Pull back the edge of the seat-back cover all the way around, and release the clips (A), then remove
the seat-back cover. 14. Install the cover in the reverse order of removal,
and note these items:
 To prevent wrinkles when installing a seat-back cover, make sure the material is stretched evenly
over the pad before securing the clips, the hooks,
and the hook strips.
 Replace any clips (A) you removed with new ones.
08/08/21 15:04:01 61SNR030_200_0132
ProCarManuals.com
DYNOMITE -2009-



(#'
 )
20-13620-136 Seats
Rear Seat-back Latch Replacement
(cont’d)
Rear Seat-back Release Lever/Cable
Removal/Installation
Fastener Location
:Clip,1
A
B
4. Install the latch in the reverse order of removal, and note these items:
 Make sure the release cable is connected securely.
 Make sure the seat-back locks securely and unlocks properly. NOTE: Take care not to bend or scratch the interior trim.
1. Open the trunk lid.
2. From the trunk compartment, detach the cable clip.
3. Disconnect the seat-back release cable (A) from the seat-back latch (B).
08/08/21 15:04:04 61SNR030_200_0138
ProCarManuals.com
DYNOMITE -2009-



(#'
 )
20-13620-136 Seats
Rear Seat-back Latch Replacement
(cont’d)
Rear Seat-back Release Lever/Cable
Removal/Installation
Fastener Location
:Clip,1
A
B
4. Install the latch in the reverse order of removal, and note these items:
 Make sure the release cable is connected securely.
 Make sure the seat-back locks securely and unlocks properly. NOTE: Take care not to bend or scratch the interior trim.
1. Open the trunk lid.
2. From the trunk compartment, detach the cable clip.
3. Disconnect the seat-back release cable (A) from the seat-back latch (B).
08/08/21 15:04:04 61SNR030_200_0138
ProCarManuals.com
DYNOMITE -2009-



(#'

 )
Special Tools Required
20-13720-137
Rear Seat Armrest Beverage Holder
Replacement
A B
C
D
D
AB
C
D
4. Push the tab (A) to release the hook (B), and rotate the seat-back release lever (C) clockwise to release
the hook (D).
5. Install the release lever/cable in the reverse order of removal, and note these items:
 Make sure the release cable is connected securely.
 Make sure the seat-back locks securely and unlocks properly. KTC trim tool set SOJATP2014
NOTE:
 Use the appropriate tool from the KTC trim tool set to avoid damage when removing components.
 Take care not to tear or damage the seat covers.
1. Using a trim tool, push on the bottom ribs (A) of the rear hooks (B) to pull up the beverage holder (C),
then release the hooks from the wire (D).
(cont’d)
08/08/21 15:04:05 61SNR030_200_0139
ProCarManuals.com
DYNOMITE -2009-



(#'

 )
Special Tools Required
20-13720-137
Rear Seat Armrest Beverage Holder
Replacement
A B
C
D
D
AB
C
D
4. Push the tab (A) to release the hook (B), and rotate the seat-back release lever (C) clockwise to release
the hook (D).
5. Install the release lever/cable in the reverse order of removal, and note these items:
 Make sure the release cable is connected securely.
 Make sure the seat-back locks securely and unlocks properly. KTC trim tool set SOJATP2014
NOTE:
 Use the appropriate tool from the KTC trim tool set to avoid damage when removing components.
 Take care not to tear or damage the seat covers.
1. Using a trim tool, push on the bottom ribs (A) of the rear hooks (B) to pull up the beverage holder (C),
then release the hooks from the wire (D).
(cont’d)
08/08/21 15:04:05 61SNR030_200_0139
ProCarManuals.com
DYNOMITE -2009-



(#'

 )
20-13820-138 Seats
Rear Seat Armrest Beverage Holder
Replacement (cont’d)
Rear Seat Armrest Replacement
A
B C
B A
B
A
B
C
2. Release the front hooks (A) from the wire (B), then
remove the beverage holder (C).
3. Install the beverage holder in the reverse order of removal. Make sure the front hooks are installed
securely to the wire, then push down on the
beverage holder and install the rear hooks into the
wire securely. NOTE: Take care not to tear the seams or damage the
seat covers.
1. Remove the clip (A) from the left portion of the armrest pivot (B).
2. Slide the armrest (A) toward the driver’s side of the vehicle, and remove the pivot shaft (B) from the
collar (C) on the right side of the vehicle by pulling
back on the armrest.
08/08/21 15:04:05 61SNR030_200_0140
ProCarManuals.com
DYNOMITE -2009-



(#'

 )
20-13820-138 Seats
Rear Seat Armrest Beverage Holder
Replacement (cont’d)
Rear Seat Armrest Replacement
A
B C
B A
B
A
B
C
2. Release the front hooks (A) from the wire (B), then
remove the beverage holder (C).
3. Install the beverage holder in the reverse order of removal. Make sure the front hooks are installed
securely to the wire, then push down on the
beverage holder and install the rear hooks into the
wire securely. NOTE: Take care not to tear the seams or damage the
seat covers.
1. Remove the clip (A) from the left portion of the armrest pivot (B).
2. Slide the armrest (A) toward the driver’s side of the vehicle, and remove the pivot shaft (B) from the
collar (C) on the right side of the vehicle by pulling
back on the armrest.
08/08/21 15:04:05 61SNR030_200_0140
ProCarManuals.com
DYNOMITE -2009-