ECU ACURA CSX 2006 Service Repair Manual


(#'


 )
20-2120-21
Rear Door Latch Replacement
Fastener Locations :Screw,3
A:Screw,1 B
A
A
A
6x1.0mm
6N·m
(0.6 kgf·m, 4 lbf·ft) 6x1.0mm
6N·m
(0.6 kgf·m, 4 lbf·ft)C
B
11. Install the handle in the reverse order of removal, and note these items:
 Make sure the door locks and opens properly.
 When reinstalling the door panel, make sure the
plastic cover is installed properly and sealed
around its outside perimeter to seal out water.
 Check for water leaks (see step 9 on page 20-29). NOTE: Put on gloves to protect your hands.
1. Raise the glass fully.
2. Remove the door panel (see page 20-17).
3. Remove the plastic cover, as needed (see step 4 on page 20-19).
4. Remove the screws (A, B) securing the latch (C), then lower it.
5. Detach the rod fastener (see step 6 on page 20-19).
6. Disconnect the outer handle rod from the outer handle (see step 7 on page 20-20).
(cont’d)
08/08/21 14:59:07 61SNR030_200_0023
ProCarManuals.com
DYNOMITE -2009-



20-22Doors
Rear Door Latch Replacement (cont’d)
A
B
C
D F
E
Fastener Location :Screw,1
AB A
A
B
C
B
7. Detach the latch cable (A) and the inner handlecable (B) from the holder (C), then remove the latch
(D) out from between the rear lower channel (E)
and the door. Take care not to bend the outer
handle rod (F), the latch cable, or the inner handle
cable.
8. Remove the screw, then remove the latch protector (A) by releasing the hook (B). 9. Detach the latch cable (A) and the inner handle
cable (B) from the latch (C).
10. Install the latch in the reverse order of removal, and note these items:
 Make sure the connector is plugged in properly, and each rod is connected securely.
 Make sure the door locks and opens properly.
08/08/21 14:59:07 61SNR030_200_0024
ProCarManuals.com
DYNOMITE -2009-




(#'


 )

20-26 Doors
Rear Door Glass Outer Weatherstrip Replacement
A
B
A
A B
NOTE:
 Put on gloves to protect your hands.
 Take care not to scratch the door.
1. Remove these items:  Door panel (see page 20-17)
 Plastic cover (see step 4 on page 20-19)
 Rear door glass (see page 20-23)
 Quarter glass (see step 9 on page 20-24)
2. Release the front hook (A) from inside of the door, then pull up the front portion of the rear door glass
outer weatherstrip (B). 3. Starting at the front, slowly pull up the rear door
glass outer weatherstrip (A).
4. Push the rear hook (A) out from inside of the door, then remove the rear door glass outer weatherstrip
(B).
5. Push the clip portions of the rear door glass outer weatherstrip into place securely.
08/08/21 14:59:10 61SNR030_200_0028
ProCarManuals.com
DYNOMITE -2009-


(#'


 )
20-27
Rear Door Weatherstrip Replacement
Fastener Locations:Bolt,1
A :Clip,13
B
B A B
C
D F
E C
E
E
E
8x1.25mm
29 N·m
(3.0 kgf·m, 22 lbf·ft) : Clip, 2
C
:Clip,1
D (White)
(Black) (Left: Yellow
Right: Green)
NOTE:
 Put on gloves to protect your hands.
 Take care not to scratch the door.
 Remove the clips with a clip remover.
1. At the B-pillar, remove the door checker mounting
bolt (A).
2. Detach the clips (B, C, D), then remove the door weatherstrip (E). 3. Install the weatherstrip in the reverse order of
removal, and note these items:
 If the clips are damaged or stress-whitened, replace them with new ones.
 Make sure the weatherstrip is installed in the holder (F) securely.
 Apply medium strength liquid thread lock to the door checker mounting bolt before installation.
 When reinstalling the door panel, make sure the
plastic cover is installed properly and sealed
around its outside perimeter to seal out water.
 Check for water leaks (see step 9 on page 20-29).
08/08/21 14:59:10 61SNR030_200_0029
ProCarManuals.com
DYNOMITE -2009-


(#'



")
20-31
Front and Rear Door Striker Adjustment
B
8x1.25mm
18 N·m (1.8 kgf·m, 13 lbf·ft) A
C
Make sure the door latches securely without slamming
it. If necessary, adjust the striker (A): The striker nuts
are fixed, but the striker can be adjusted slightly up or
down, and in or out.1. Loosen the screws (B).
2. Wrap the striker with a shop towel, then adjust the striker by tapping it with a plastic hammer (C). Do
not tap the striker too hard.
3. Lightly tighten the screws.
4. Hold the outer handle out, and push the door against the body to be sure the striker allows a
flush fit. If the door latches properly, tighten the
screws to the specified torque, and recheck.
08/08/21 15:00:02 61SNR030_200_0033
ProCarManuals.com
DYNOMITE -2009-



(#'
 )
20-34 Mirrors
Mirror Holder Replacement
A
B C
A
B
C
D E
C
E
F A
B
C B
A B
C
A
C
CB A
A
B
C
NO GOOD
OK
NOTE: Put on gloves to protect your hands.
1. Carefully push on the top edge of the mirror holder (A) by hand.
2. Put a shop towel in the opening between the lower edge of the mirror holder and the mirror housing
(B) to prevent scratches, and detach the bottom
clips (C) with a flat-tip screwdriver wrapped with
protective tape.
3. Carefully pull out the bottom edge of the mirror holder (A) to separate the adhesive (B), and then
release the side clips (C).
4. Separate the mirror holder from the actuator (D) by releasing the hooks (E). Disconnect the mirror
defogger connectors (F) from the heater pad
terminals. 5. Before reinstalling the mirror holder to the inner
holder (A) on the actuator, check the actuator rods
(B) and the actuator boots (C). Make sure the
actuator rods are securely mounted in the holes,
and that the boots properly cover each rod.
6. Reconnect the mirror defogger connectors.
7. Reattach the hooks of the mirror holder to the actuator, then position the mirror holder on the
actuator. Carefully push on the clip portions of the
mirror holder until the mirror holder locks into
place.
8. Check the actuator operation.
08/08/21 15:00:05 61SNR030_200_0036
ProCarManuals.com
DYNOMITE -2009-

´µ
´µ
´µ ´ µ

Î
(#'
") Î

(#'
 )
´µ ´µ
´µ ´
µ
20-5520-55
Glass Position Adjustment Glass Replacement
13.5 1/ 1 mm
(0.55 0.04/ 0.04 in.)
AB
01/1mm
(0 0.04/ 0.04 in.)
Fastener Locations 5x0.8mm
4N·m
(0.4 kgf·m, 3 lbf·ft)
:TORXScrew,6
Front A
Fastener Locations
:Screw,2
Front
5x0.8mm
4N·m
(0.4 kgf·m, 3 lbf·ft)
F
:TORXScrew,6
BE
B
D
C
D C
A
E E
E
A
The roof panel (A) should be
even with the glass
weatherstrip (B), to within 0 1/ 1 mm
(0 0.04/ 0.04 in.) all the way around, and the distance
from glass edge to the roof panel edge should be
13.5 1/ 1 mm (0.55 0.04/ 0.04 in.). If not, make the
following adjustment:
1. Remove the bracket cover.
2. Adjust the glass (A). –1 Slightly loosen the screws with a TORX T25 bit.
–2 Move the glass up or down and forward orrearward.
–3 Tighten all screws securely.
3. If necessary, repeat on the opposite side. 1. Close the glass fully.
2. Slide the sunshade all the way back.
3. Pry out the lid (A), remove the screws (B), and
release the hooks (C), then remove both bracket
covers (D). Remove the screws (E) with a TORX T25
bit from both glass brackets (F).
4. Remove the glass (A) by lifting it up. Do not damage the roof panel.
5. Install the glass in the reverse order of the removal, and adjust the glass position alignment (see page
20-55).
6. Reset the moonroof control unit (see page 22-287).
7. Check for water leaks. Use free-flowing water from a hose without a nozzle. Do not use high-pressure
water.
NOTE: It is normal for some water to seep past the
moonroof into the moonroof frame, and exit
through the drains.
08/08/21 15:00:19 61SNR030_200_0057
ProCarManuals.com
DYNOMITE -2009-



(#'
 )
20-57
Drain Channel Replacement
A
B A A
C
B
A
1. Remove the glass (see page 20-55).
2. Move both glass brackets (A) with a 5 mm hexagonal wrench to the position where the
moonroof normally tilts up, and disconnect the
drain channel rods (B) on both sides.
3. Slide the drain channel (A) forward. 4. Pull up the rear edge of the drain channel (A) while
pushing both clips (B), and release the channel
from both hooks (C) of the drain channel slider by
pulling it rearward.
5. Remove the drain channel.
6. Install the channel in the reverse order of removal, and note these items:
 Push the clip portions into place securely.
 Check the glass position adjustment (see page 20-55).
7. Check for water leaks. Let the water run freely from a hose without a nozzle. Do not use a high-pressure
spray.
08/08/21 15:00:20 61SNR030_200_0059
ProCarManuals.com
DYNOMITE -2009-



(#' )

20-62 Moonroof
Drain Channel Slider and Cable Assembly Replacement
A
B
C D
E 6x1.0mm
9.8 N·m
(1.0 kgf·m, 7.2 lbf·ft)
F G
Fastener Locations Fastener Locations
:Screw,2
A:Screw,2 B:Bolt,2E
:Screw,2
F
A
B
C
D
E
C
C
Front
1. Remove the frame (see page 20-60).
2. Remove these parts from the frame:
 Sunshade (see page 20-58)
 Moonroof motor (see page 20-59)
3. Put on gloves to protect your hands. Remove the screws (A, B) securing the slide stops (C), and the
cable tube rear brackets A (D), the cable tube side
bracket mounting bolts (E) and the cable tube
mounting screws (F) from both sides of the frame
(G). 4. Turn both cable tube side brackets (A) up to release
the hooks (B) from the holes in both sides of the
frame.
5. Pivot the glass brackets (C) down by sliding the link lifters (D) back, then slide both glass brackets back
with the link lifters.
6. Slide the cable assembly (E) half-way back.
08/08/21 15:01:23 61SNR030_200_0064
ProCarManuals.com
DYNOMITE -2009-




(#' )

D

river’s side
Passenger’s side Special Tools RequiredRear Door Sill Area
20-6720-67
Fastener Locations
:Clip,2
A
Fastener Locations :Clip,2
B Fastener Locations
:C
lip,2
(White)
A
B C
D
A
5. Pull the driver’s kick panel (A) or the passenger’skick panel (B) back by hand to detach the clips, then
remove it.
6. Install the trim in the reverse order of removal, and note these items:
 If the clips are damaged or stress-whitened, replace them with new ones.
 Push the clips and the hooks into place securely. KTC trim tool set SOJATP2014
NOTE: 
Put on gloves to protect your hands.
 Take care not to bend or scratch the trim and panels.
 Use the appropriate tool from the KTC trim tool set to avoid damage when removing components.
1. Detach the hooks (A) and the tab (B) from the B-pillar lower trim (C), and pull the rear door sill
trim(D)upbyhandtodetachtheclips,then
remove it.
(c

ont’d)
08/08/21 15:01:29 61SNR030_200_0069
ProCarManuals.com
DYNOMITE -2009-