lock Acura Integra 2000 Hatchback Workshop Manual

Powe
r Steerin g

Check the level when the engine is
cold. Look at the side of the
reservoir. The fluid should be
between the UPPER LEVEL and LOWER LEVEL. If it is below the
LOWER LEVEL, add power steering
fluid to the UPPER LEVEL. Always use Genuine Honda Power
Steering Fluid. If it is not available,
you may use another power steering
fluid as an emergency replacement. However, continued use can cause
increased wear and poor steering incold weather. Have the power
steering system flushed and refilled
with Honda PSF as soon as possible. A low power steering fluid level can
indicate a leak in the system. Check
the fluid level frequently and have
the system inspected as soon as

possible.

Turning the steering wheel to full left

or right lock and holding it there can

damage the power steering pump.

Maintenance

NOTIC
E

UPPE
R LEVE L

LOWE R LEVE L

Wipe
r Blade s
Check the condition of the wiper
blades at least every six months. Look for signs of cracking in the
rubber, or areas that are getting
hard. Replace the blades if you find
these signs, or they leave streaks and unwiped areas when used.
To replace the blade:1. Raise the wiper arm off the
windshield.

2. Disconnect the blade assembly

from the wiper arm by pushing in
the lock tab. Hold it in while you
push the blade assembly toward
the base of the arm.

Maintenanc e WIPE
R ARM S

LOCK TA B

Wipe
r Blade s
3. Remove the blade from its holder by grasping the tabbed end of the
blade. Pull firmly until the tabs
come out of the holder. 4. Examine the new wiper blades. If
they have no plastic or metal rein-
forcement along the back edge,
remove the metal reinforcement
strips from the old wiper blade and
install them in the slots along the edge of the new blade.

5. Slide the new wiper blade into the

holder until the tabs lock.

6. Slide the wiper blade assembly

onto the wiper arm. Make sure it
locks in place.

7. Lower the wiper arm down against

the windshield.

Maintenanc e

BLAD
E BLADE
REINFORCEMEN T

Ai
r Conditionin g Syste m

Optional for Type-R model

Your car's air conditioning is a sealed system. Any major maintenance,
such as recharging, should be done
by a qualified mechanic. You can do a couple of things to make sure theair conditioning works efficiently. Periodically check the engine's
radiator and air conditioning
condenser for leaves, insects, and
dirt stuck to the front surface. These
block the air flow and reduce cooling efficiency. Use a light spray from a
hose or a soft brush to remove them.

The condenser and radiator fins bend
easily. Only use a low-pressure spray
or soft-bristle brush to clean them.

Run the air conditioning at least once
a week during the cold weather
months. Run it for at least ten
minutes while you are driving at a steady speed with the engine at
normal operating temperature. This
circulates the lubricating oil con-
tained in the refrigerant. If the air conditioning does not get as
cold as before, have your dealer
check the system. Recharge the
system with Refrigerant HFC-134a (R-134a). (See Specifications on page 250.)

Whenever you have the air conditioning

system serviced, make sure the service

facility uses a refrigerant recycling
system. This system captures the
refrigerant for reuse. Releasing
refrigerant into the atmosphere can

damage the environment.

Maintenanc e

AI
R CONDITIONIN G

CONDENSE R
NOTIC
E NOTIC
E

Light
s

Replacin g a Headligh t Bul b
Your car has two bulbs on each side, four in total. Make sure you arereplacing the bulb that is burned out.
Your car uses halogen headlight bulbs. When replacing a bulb, handle
it by its plastic case and protect the
glass from contact with your skin or
hard objects. If you touch the glass,clean it with denatured alcohol and a
clean cloth.

Halogen headlight bulbs get very hot when lit. Oil, perspiration, or a scratch
on the glass can cause the bulb to
overheat and shatter.
1. Open the hood.
If you need to change the high
beam headlight bulb on the
passenger's side, remove the
radiator reserve tank by pulling it straight up.

2. To disconnect the bulb from the

electrical harness, push on the end
of the lock tab to release the
connector then push the connec-
tor straight down.

3. Turn the bulb about one-eighth

turn counterclockwise to unlock it
from the headlight assembly.

4. Remove the bulb by pulling it

straight out of its recess.

5. Align the tabs on the new bulb
with the slots in the headlightassembly and push it into place.
6. Turn the bulb clockwise to lock it

in place. Do not force it. Check the seating of the bulb's tabs in the
slots if the bulb will not return to
its original position.

7. Reinstall the harness connector on

the bulb connector. Make sure it
locks in place.
Turn on the headlights to test the new bulb.

8. (Passenger's side)

Reinstall the radiator reserve tank.

Maintenanc e

NOTIC
E

Light
s
Replacing Front Turn Signal/
Parkin g an d Sid e Marke r Ligh t
Bulb s
1. Use a Phillips-head screwdriver to

loosen the light assembly's mounting screw.

2. Remove the light assembly from

the bumper.

3. Remove the socket of the burned-

out bulb from the light assembly
by turning it one-quarter turn counterclockwise.

4. To remove the front bulb, push it

in slightly and turn it counterclock-
wise. To remove the side bulb, pull it straight out of its socket.

5. Install the new bulb in the socket.
6. Insert the socket back into the

light assembly. Turn it clockwise
to lock it in place.

7. Test the lights to make sure the

new bulb is working.

8. Put the light assembly into the

bumper. Make sure the tab on the
light assembly fits into the bumper slot. Tighten the mounting screw.

Maintenanc e
SCRE
W

Light
s

Replacin g a High-moun t Brak e
Ligh t Bul b
LS model
1. Undo the cover fasteners by
pushing on the center of each
fastener's head until it pops in.
Remove the cover.

2. Determine which bulb is burned

out.

3. Pull the bulb straight out of its

socket.
Push the new bulb straight into
the socket until it bottoms.

4. Test the lights to make sure the

new bulb is working.

5. Reset each fastener by pushing on

the pointed end until it pops back almost flush with the fingers on
the housing.

6. Reinstall the cover. Secure each

fastener by pushing on the center
until it locks (the center is flush
with the head).

Maintenanc e

Light
s

Replacin g Rea r Tur n Signa l an d
Sid e Marke r Ligh t Bulb s
1. Open the hatch and remove the
light assembly cover by pulling the
edge.

2. Remove the socket from the light assembly by turning it one-quarter

turn counterclockwise.

3. If the turn signal light bulb is

burned out, remove it by pushing
it in and turning counterclockwise.If the side marker light bulb is
burned out, remove it by pulling it straight out of its socket.

4. Install the new bulb in the reverse

order of removal.

5. Push the socket into the light

assembly and turn it clockwise
until it locks.

6. Test the lights to make sure the

new bulb is working.

7. Install the light assembly cover.

Make sure it locks in place.

Replacin g Tail/Stopligh t an d
Back-u p Ligh t Bulb s
1. Open the hatch. Remove the

tether hardware cover with a small
flat-tip screwdriver and tether
anchor plate with a wrench by turning the bolt counterclockwise.

When reinstalling tether hardware,

see Protecting Children on page

41.

On Type-R model

You cannot replace these bulbs
yourself, contact your Acura dealer.
Maintenanc e

Light
s

2. Undo the seven cover fasteners by
pushing on the center of each
fastener's head until it pops in. Remove the taillight cover panel.

3. Remove the socket by turning it
one-quarter turn counterclockwise. 4

. Try the tail/stoplights and back-up
light to verify which bulb needsreplacing. Remove the bulb by
turning it counterclockwise.

5. Install the new bulb in the socket.

Test it to make sure it works.

6. Reinstall the socket into the light

assembly.

7. Reinstall the tether anchor

hardware. Make sure the toothed washer ison the bottom of the bolt. Tighten
the bolt to:
16 lbf.ft (22 N.m , 2.2 kgf.m)
If a torque wrench was not used,
see your Acura dealer as soon as
possible to verify proper
installation.

CONTINUED

Maintenanc e

Light
s
8. Reset each fastener by pushing onthe pointed end until it pops back almost flush with the fingers on
the housing.
9. Reinstall the cover. Secure each
fastener by pushing on the center
until it locks (the center is flush with the head).
Replacin g a Rea r Licens e Bul b
1. Remove the two screws and
remove the license light assembly.
2. Remove the socket from the light assembly by turning it one-quarter
turn counterclockwise.
3. Pull the bulb straight out of its
socket. Push the new bulb in until
it bottoms in the socket.
4. Turn on the parking lights and
check that the new bulb is
working.
5. Reinstall the license light assem-
bly. Install the two screws and
tighten them securely.
Maintenanc e