lights Acura Integra 2000 Sedan Owner's Guide

Towin
g a Traile r

Additional Trailer equipment

Many states and Canadian provinces
require special outside mirrors when
towing a trailer. Even if they don't,
you should install special mirrors if you cannot clearly see behind you, orif the trailer creates a blind spot.
Ask your trailer sales or rental
agency if any other items are recommended or required for your
towing situation. Pre-To
w Checklis t
When preparing to tow, and before driving away, be sure to check the
following:
The vehicle has been properlyserviced, and the tires, brakes,
suspension, and cooling system
are in good operating condition. All weights and loads are within
limits (see page 147).
The hitch, safety chain, and any other attachments are sucure. All items on and in the trailer are
properly secured and cannot shift
while you drive. The lights and brakes on your
vehicle and the trailer are working
properly. Your vehicle tires and spare are
properly inflated (see page 192 ),and the trailer tires and spare are
inflated as recommended by the trailer maker.

Drivin g

This section explains why it is important to keep your car well
maintained and to follow basic
maintenance safety precautions.
This section also includes Maintenance Schedules for normaldriving and severe driving conditions,
a Maintenance Record, and instruc-
tions for simple maintenance tasks
you may want to take care of

yourself.

If you have the skills and tools to per-
form more complex maintenance tasks on your Acura, you may want
to purchase the Service Manual. Seepage 259 for information on how to
obtain a copy, or see your Acura
dealer.
Maintenance Safety....................... 154
Important Safety Precautions.. 155
Maintenance Schedule.................. 156
Maintenance Record..................... 163
Owner Maintenance Checks........ 165
Fluid Locations............................... 166

Engine Oil......................................
. 167
Adding Oil................................... 167
Recommended Oil..................... 167

Synthetic Oil............................... 169

Additives..................................... 169
Changing the Oil and Filter...... 170
Cooling System.............................. 172 Adding Engine Coolant............. 172Replacing Engine Coolant........ 174
Windshield Washers..................... 177
Transmission Fluid........................ 178 AutomaticTransmission.......................... 178

5-speed Manual
Transmission.......................... 179
Brake and Clutch Fluid................. 179 Brake System............................. 180Clutch System............................
181
Power Steering..............................
. 181
Air Cleaner Element....................... 182 Hood Latch..................................... 183
Spark Plugs..................................... 183 Replacement............................... 183
Specifications............................. 185
Battery............................................ 186
Wiper Blades.................................. 188
Air Conditioning System............... 190
Drive Belts...................................... 191
Timing Belt..................................... 191
Tires................................................ 192 Inflation....................................... 192
Inspection...................................
194
Maintenance............................... 194
Tire Rotation.............................. 195 Replacing Tires and Wheels.... 195
Wheels and Tires....................... 196 Winter Driving........................... 196

Snow Tires.............................. 197

Tire Chains............................. 197
Lights.............................................. 198
Headlight Aiming.....................
. 200
Replacing Bulbs......................... 202
Storing Your Car............................ 210

Maintenance

Owne
r Maintenanc e Check s
You should check the following items at the specified intervals. If
you are unsure of how to perform any check, turn to the page given. Engine oil level — Check every
time you fill the fuel tank. See
page 122.
Engine coolant level — Check the
radiator reserve tank every time
you fill the fuel tank. See page 123 , Windshield washer fluid — Check
the level in the reservoir monthly.
If weather conditions cause you to
use the washers frequently, check
the reservoir each time you stop
for fuel. See page 177. Automatic transmission — Check
the fluid level monthly. See page
178.
Brakes — Check the fluid level
monthly. See page 179 . Tires — Check the tire pressure
monthly. Examine the tread for
wear and foreign objects. See page 192. Lights — Check the operation of
the headlights, parking lights,
taillights, high-mount brake light, turn signals, brake lights, and
license plate lights monthly. See

page 198.

Maintenance

Light
s
Check the operation of your car's
exterior lights at least once a month.
A burned out bulb can create an unsafe condition by reducing yourcar's visibility and the ability tosignal your intentions to other

drivers.

Maintenanc e
HEADLIGHT
S
FRONT PARKING /
FRON T TUR N SIGNA L
LIGH T FRON
T SID E
MARKE R LIGH T

Light
s

Check the following: Headlights (low and high beam) Parking lights
Taillights Brake lights
High-mount brake light
Turn signals
Back-up lights Hazard light function
License plate light
Side marker lights
If you find any bulbs are burned out,
replace them as soon as possible.
Refer to the chart on page 247 to determine what type of replacement
bulb is needed.

Maintenance

TAILLIGH
T
INNE R TAILLIGH T
LICENS E PLAT E LIGHT S

Light
s
Headligh t Aimin g
The headlights were properly aimed when your car was new. You should check their aim if you regularly carry
heavy items in the trunk or pull a
trailer. Each headlight assembly has
horizontal and vertical adjustment indicators. These are set to their "0"
positions after the headlights are
aimed at the factory. To check these settings:
1. Make sure the fuel tank is full. Park the vehicle on level ground.
2. The driver or someone who weighs the same should be sittingin the driver's seat for all checksand adjustments.
Load the trunk with the items you
normally carry.
HORIZONTA
L ANGL E GAUG E

If you usually pull a trailer, load it as
you would normally and attach it to the car. Push down on the front and
rear bumpers several times to makesure the car is sitting normally.
3. Open the hood.
4. Check the horizontal angle gauge. The line on the adjustment screwindicator should line up with the"0" mark on the gauge.
Maintenanc e
Righ
t headligh t

Lef t headligh t

Light
s
Replacin g a Headligh t Bul b
Your car has two bulbs on each side, four in total. Make sure you arereplacing the bulb that is burned out.
Your car uses halogen headlight bulbs. When replacing a bulb, handleit by its plastic case and protect the
glass from contact "with your skin or hard objects. If you touch the glass,clean it with denatured alcohol and a
clean cloth.

Halogen headlight bulbs get very hot
when lit. Oil, perspiration, or a scratch
on the glass can cause the bulb to
overheat and shatter.
1. Open the hood.
If you need to change the high
beam headlight bulb on the
passenger's side, remove the
radiator reserve tank by pulling itstraight up.
2. To disconnect the bulb from the electrical harness, push on the end
of the lock tab to release the
connector then push the connec-
tor straight down. 3. Turn the bulb about one-eighth
turn counterclockwise to unlock it
from the headlight assembly.
4. Remove the bulb by pulling it straight out of its recess.
5. Align the tabs on the new bulb with the slots in the headlightassembly and push it into place.
6. Turn the bulb clockwise to lock it in place. Do not force it. Check theseating of the bulb's tabs in the
slots if the bulb will not return to
its original position.
7. Reinstall the harness connector on the bulb connector. Make sure it
locks in place.
Turn on the headlights to test the new bulb.
8. (Passenger's side) Reinstall the radiator reserve tank.

Maintenanc e

NOTIC
E

Light
s

Replacin g Fron t Tur n Signal /
Parkin g an d Sid e Marke r Ligh t
Bulb s
1. Use a Phillips-head screwdriver to loosen the fight assembly's
mounting screw.
2. Remove the light assembly from the bumper. 3. Remove the socket of the burned-
out bulb from the light assembly
by turning it one-quarter turn
counterclockwise.
4. To remove the front bulb, push it in slightly and turn it counterclock-
wise. To remove the side bulb, pull
it straight out of its socket. 5. Install the new bulb in the socket.
6. Insert the socket back into the
light assembly. Turn it clockwise
to lock it in place.
7. Test the lights to make sure the new bulb is working.
8. Put the light assembly into the bumper. Make sure the tab on the
light assembly fits into the bumperslot. Tighten the mounting screw.
Maintenance

SCRE
W

Light
s
4. Remove the socket by turning it one-quarter turn counterclockwise.
5. If the turn signal light bulb or tail/stoplight bulb is burned out,remove it by pushing it in and
turning counterclockwise. If the side marker light bulb is burned
out, remove it by pulling it straight
out of its socket. 6. Install the new bulb in the reverse
order of removal.
7. Push the socket into the light assembly and turn it clockwise
until it locks.
8. Test the lights to make sure the new bulb is working.
9. Install the wall lining and the trunk wall cover and secure them with
the fasteners. Refer to page206 for reinstallation of the
fasteners. Removal and Reinstallation of
Fasteners
(A Type)

Removal:

Turn the center of the fastener one- quarter turn counterclockwise using
a coin or a screwdriver. The center
will come out slightly. Then remove the fastener.

CONTINUED

Maintenanc e

Light
s

Replacin g Rea r Bulb s (i n Trun k

Lid )
1. Open the trunk.
2. Use a Phillips-head screwdriver to remove the two screws from the
bulb holder. Remove the holder
from the taillight assembly. 3. Try the tail/stoplight and back-up
lights to verify which bulb needs
replacing. Remove that bulb from
the socket by pushing it in slightly and turning it counterclockwise.
4. Install the new bulb in the socket. Test it to make sure it works.
5. Reinstall the bulb holder assembly. Install the two screws and tighten
them securely. Replacin
g a Rea r Licens e Bul b
1. Remove the two screws and remove the license light assembly.
2. Remove the socket from the light assembly by turning it one-quarterturn counterclockwise.
3. Pull the bulb straight out of its socket. Push the new bulb in until
it bottoms in the socket.

Maintenance

CONTINUED