dashboard ACURA NSX 1991 Service Manual PDF
[x] Cancel search | Manufacturer: ACURA, Model Year: 1991, Model line: NSX, Model: ACURA NSX 1991Pages: 1640, PDF Size: 60.48 MB
Page 1594 of 1640
CAUTION:
All SRS electrical wiring harnesses are covered with
yellow outer Insulation. Before disconnecting the SRS wire harness, Install
the short connector on the airbag (see page STET). Replace the entire affected SRS harness assembly
if it has an open circuit or damaged wiring. After installation of the gauge assembly, recheck the
operation of the SRS indicator light.
Remove the dashboard lower cover, center panel and in-
strument panel. Disconnect the 8-connector (30-P) from
the gauge assembly. (See page 23-126)
Make the following input tests at the connector termi-
nals. If all tests prove OK, yet the indicator stilt fails to
work, replace the safety indicator.
A-CONNECTOR (Carries the SRS indicator signal)
SRS MAIN WIRE HARNESS
A-CONNECTOR
YEL
GRN/RED
View from terminal side
Safety Indicator
Indicator Input Test
B-CONNECTOR
RED/YEL
BLK/WHT
GRN/BLK
BLU
GRN/BLU
BLKProCarManuals.com
Page 1598 of 1640
Shift Lever Position Indicator
CAUTION: All SRS electrical wiring harnesses are covered with
yellow outer insulation. Before disconnecting the SRS wire harness, Install
the short connector on the airbus (see page 23-323). Raplace the entire affected SRS harness assembly
if it has an open circuit or damaged wiring. After installation of the gauge assembly, recheck the
operation of the SRS indicator light.
Remove the gauge assembly from the dashboard and dis-
connect the 30-P connector from the gauge assembly.
Make the following input tests at the connector termi-
nals. If all tests prove OK, yet the indicator still fails to
work, replace the main printed circuit panel, speedome-
ter, tachometer and odo/trip meter.
A-CONNECTOR (Carries the SRS indicator signal)
SRS MAIN WIRE HARNESS
A-CONNECTOR
30-P CONNECTOR
Indicator Input Test
YEL
BLK
RED/BLK
RED
LT GRN
GRN/YEL
LT GRN/WHT
YEL/BLU
GRY/WHT
GRN
LT BLU
YEL/BLK
BRN/BLK
View from wire sideProCarManuals.com
Page 1607 of 1640
Lighting/Turn Signal Switch Test
1. Remove the dashboard lower cover and dashboard center panel.
2. If necessary, remove the knee bolster. 3. Disconnect the 16-P connector from the floor wire
harness.
4. Check for continuity between the terminals in each switch position according to the table.
KNEE BOLSTER
DASHBOARD CENTER
PANEL
Lighting/Dimmer/Passing Switch
Turn Signal Switch
DASHBOARD LOWER COVER
View from wire side
16-P CONNECTORProCarManuals.com
Page 1608 of 1640
Lighting System
Lighting Switch Replacement
CAUTION: All SRS electrical wiring harnesses are covered with
yellow outer insulation.
Before disconnecting the SRS wire harness, install
the short connector on the airbag (see page 23-323). Replace the entire affected SRS harness assembly
if it has an open circuit or damaged wiring.
1. Remove the dashboard lower cover and disconnect the 2-P connectors from the floor wire harness.
2-P
CONNECTORS
DASHBOARD
LOWER COVER
2. Remove the dashboard center panel.
DASHBOARD CENTER
PANEL
3.
Remove
the
tilt
cover.
TILT COVER
4. Remove the steering column lower cover and upper
cover.
5. Disconnect the 16-P connector and 10-P connector.
10-P
CONNECTOR
16-P CONNECTORProCarManuals.com
Page 1611 of 1640
Side Marker/Turn Signal/Hazard Flash System
Turn Signal/Hazard Relay Input Test
Remove the dashboard lower cover.
Remove the turn signal/hazard relay from the left kick
panel then disconnect the 6-P connector.
Make the following input tests at the 6-P connector ter-
minals.
If all tests prove OK, but the relay fails to work, replace
the turn signal/hazard relay.
View from
terminal side
TURN SIGNAL/
HAZARD RELAYProCarManuals.com
Page 1620 of 1640
Switch Removal
CAUTION: All SRS electrical wiring harnesses are covered withyellow outer insulation.Before disconnecting the SRS wire harness, install
the short connector on the airbag (see page 23-323). Replace the entire affected SRS harness assembly
if it has an open circuit or damaged wiring.
1. Remove the dashboard lower cover and disconnect the 2-P connectors from the floor wire harness.
2-P
CONNECTORS
LIGHTS-ON CHIME
FOOT LIGHT
DASHBOARD
LOWER COVER
2. Disconnect the 18-P connector from the floor wire harness.
CAUTION: Be careful not to damage SRS wires.
REAR WINDOW
DEFOGGER SWITCH
18-P
CONNECTOR
3.
Remove
the
tilt
cover.
TILT COVER
4. Remove the steering column lower cover and upper
cover.
NOTE: Be careful not to damage the steering column
covers.
5. Remove the 4 screws, then remove the rear window defogger switch and wiper/washer switch assembly.
REAR WINDOW
DEFOGGER
SWITCH
HAZARD
SWITCH
WINDSHIELD WIPER/WASHER
SWITCHProCarManuals.com
Page 1622 of 1640
Wipers/Washers
Windshield Wiper Motor
Replacement
1. Open the hood and remove the cap nuts and the wiper arms.
NOTE: Carefully remove the wiper arms so that they
do not touch the hood.
2. Remove the windshield lower molding, hood seal and air scoop by prying off the trim clips and removing
the screws (see page 23-281).
3. Disconnect the 5-P connector from the wiper mo- tor assembly, then remove the 2 mounting bolts and
the wiper linkage assembly.
WIPER LINKAGE ASSEMBLY
5-P CONNECTOR
4. Remove the 3 mounting bolts and 1 nut from the wiper linkage assembly to remove the wiper motor.
NUT
18 N·m (1.8 kg-m, 12.8 Ib-ft)
MOUNTING
BOLTS
8 N·m
(0.8 kg-m.
5.7 Ib-ft)
WIPER LINKAGE
ASSEMBLY
WIPER MOTOR
5. Install the wiper motor assembly in the reverse ord- er of removal. Wiper/Washer Switch
Replacement
CAUTION: All SRS electrical wiring harnesses are covered with
yellow outer insulation.Before disconnecting the SRS wire harness, install
the short connector on the airbag (see page 23-323).
Replace the entire affected SRS harness assembly
if it has an open circuit or damaged wiring.
SRS MAIN WIRE HARNESS
1. Remove the dashboard lower cover and disconnect the 2-P connectors from the floor wire harness.
2-P
CONNECTORS
DASHBOAD LOWER
COVERProCarManuals.com
Page 1629 of 1640
Cruise Control
Main Switch Replacement
CAUTION:
All SRS electrical wiring harnesses are covered with
yellow outer insulation.Before disconnecting the SRS wire harness, install
the short connector on the airbag (see page 23-323). Replace the entire affected SRS harness assembly if it has an open circuit or damaged wiring.
1. Remove the dashboard lower cover and disconnect the 2-P connectors from the floor wire harness.
SRS MAIN WIRE HARNESS
2-P
CONNECTORS
LIGHTS-ON CHIME
FOOT LIGHT DASHBOARD
LOWER COVER
2. Remove the dashboard center panel.
DASHBOAD CENTER
PANEL
3.
Remove
the
tilt
cover.
TILT COVER
4. Remove the steering column lower cover and upper
cover.
5. Disconnect the 16-P connector and the 10-P
connector.
10-P
CONNECTOR
16-P CONNECTOR
CAUTION: Be careful not to damage the SRS wires.ProCarManuals.com
Page 1630 of 1640
6. Remove the 4 screws from the lighting switch.
7. Remove the lighting switch (main switch).
LIGHTING SWITCH
10-P CONNECTOR
16-P CONNECTOR
Main Switch Test
1. Remove the dashboard lower panel and dashboard
center cover.
2. If necessary, remove the knee bolster.
3. Check for continuity between the terminals in each
switch position according to the table.
CRUISE
MAIN
SWITCH
16-P CONNECTOR
View from terminal sideProCarManuals.com