ignition Acura RL 2002 3.5 Owner's Guide

Your car comes with two master
keys and a valet key.Donotdropthekeysorsetheavy
objects on them.
These keys contain electronic
circuits that are activated by the
Immobilizer System. They will not
work to start the engine if the
circuits are damaged.
Protect the keys f rom direct
sunlight, high temperature, and
high humidity.
Keep the keys away f rom liquids.
If they get wet, dry them immedi-
ately with a soft cloth.
The keys do not contain batteries.
Do not try to take them apart.
The master key fits all the locks on
your car:
 Ignition
 Doors
 Trunk
 Trunk pass-through cover
Glovebox The valet key works only in the
ignition and the door locks. You can
keep the trunk, trunk pass-through
cover, and glove box locked when
you leave your car and the valet key
at a parking facility.
Youshouldhavereceivedakey
number plate with your keys. You
will need this key number if you ever
have to get a lost key replaced. Keep
the plate stored in a saf e place. If youneed to replace a key, use only an
Acura-approved key blank.
Keys
Keys and Locks
Inst rument s and Cont rols74
K KE
EY
Y
N
NU UMM B
BEER
R
P
P L
LAA T
TE
E V
V
A
AL
LEE T
T
K
KE EY
Y
(
( G
Gr raay y))
M
M
A
AS
STTE
ER
R
K
KE EY
YS S
(
( B
Bl laac ckk) )
01/09/28 19:37:09 31SZ3660_077

Your car also comes with two remote
transmitters; see page for an
explanation of the operation.
Youshouldalsoreceiveasmallcase
containing a learning key. It is used
by the Acura dealer to code replace-
ment keys to your car’s Immobilizer
System. It must not be used in your
car’s ignition switch. Store the learn-
ing key with the key number plate in
a safe place. If you attempt to use the learningkey to start your car’s engine, it may
cause a malfunction in the system
that makes your master and valet
keys unusable. If this happens, you
should contact your Acura dealer.
If you need a new key made, take the
key number plate, the learning key,
and all other keys that came with
your car to your Acura dealer.The Immobilizer System protects
your car f rom thef t. A properly-
coded master or valet key must be
used in the ignition switch f or the
engine to start. If an improperly-
coded key (or other device) is used,
the engine’s f uel system is disabled.
When you turn the ignition switch to
ON (II), the Immobilizer System
indicator should come on f or a f ew
seconds, then go out. If the indicator
starts to blink, it means the system
does not recognize the coding of the
key. Turn the ignition switch to
LOCK (0), remove the key, reinsert
it, and turn the switch to ON (II)
again.
79
CONT INUED
Remote Transmitter
L earning K eyImmobilizer System
Keys and Locks
Inst rument s and Cont rols75
01/09/28 19:37:20 31SZ3660_078

As required by the FCC:This device complies with Part 15 of theFCC rules. Operation is subject to thef ollowing two conditions: (1) This devicemay not cause harmf ul interf erence, and(2) this device must accept anyinterf erence received, includinginterf erence that may cause undesiredoperation.
Changes or modif ications not expresslyapproved by the party responsible f orcompliance could void the user’sauthority to operate the equipment.
This device complies with IndustryCanada Standard RSS-210.Operation is subject to the f ollowing twoconditions: (1) this device may not causeinterf erence, and (2) this device mustaccept any interf erence that may causeundesired operation of the device.The system may not recognize your
key’s coding if another immobilizer
key or other metal object is near the
ignition switch when you insert the
key. To make sure the system
recognizes the key code: If you have lost your key and you cannot start the engine, contact your
Acura dealer. Do not attempt to alter this system
or add other devices to it. Electrical
problems could result that may make
your car undriveable.
Do not keep other immobilizer
keys on the same key ring.
Use a plastic or leather key f ob,
not metal.
Keep other keys away f rom your
vehicle’s key and the ignition
switch while trying to start the
engine.
If the system repeatedly does not
recognize the coding of your key,
contact your Acura dealer.
The Immobilizer System indicator
will also blink several times when
you turn the ignition switch f rom ON
(II) to ACCESSORY (I) or LOCK (0).
Keys and Locks
Inst rument s and Cont rols76
01/09/28 19:37:30 31SZ3660_079

µ
µ
µ µ
The ignition switch is on the right
side of the steering column. It has
f our positions:
LOCK(0)
 ACCESSORY (I)
 ON (II)
 START (III) If the f ront wheels are turned, the
anti-thef t lock may sometimes make
it difficult to turn the key from
LOCK to ACCESSORY. Firmly turn
the steering wheel to the lef t or to
the right as you turn the key.
In this position,
you can operate the audio system
and the cigarette lighter. You can insert or
remove the key only in this position.
To switch f rom ACCESSORY to
LOCK, you must push the key in
slightly as you turn it. The shif t lever
must also be in Park. The anti-thef t
lock will lock the steering column
when you remove the key.
This is the normal key
position when driving. All f eatures
and accessories on the car are usable.
Several of the lights on the instru-
ment panel come on as a test when
you turn the ignition switch f rom ACCESSORY to ON.
Use this position
only to start the engine. The switch
returns to ON (II) when you let go of
the key.
The engine will not start if the
Immobilizer System does not
recognize the key’s coding (see page ).
You will hear a reminder beeper if
you leave the key LOCK (0) or
ACCESSORY (I) position and open
thedriver’sdoor.Removethekeyto
turn of f the beeper. 69
Ignition Switch
A CCESSORY (I) LOCK (0)
ON (II)ST A RT (III)
Keys and Locks
Inst rument s and Cont rols77
01/09/28 19:37:41 31SZ3660_080

Each f ront door has a master door
lock switch. Either switch locks and
unlocks all doors. Push the switch
down to lock all doors, and up to
unlock them.Each door has a lock tab at the top of
the door. When you push down the
lock tab on the driver’s door, all
doors lock. Pulling up the lock tab on
the driver’s door only unlocks that
door.Thelocktaboneach
passenger’s door only locks and
unlocks that door.To lock any passenger’s door when
getting out of the car, push the lock
tab down and close the door. To lock
the driver’s door, remove the key
f rom the ignition switch and push
the lock tab down or push the master
switch down, then close the door.
All doors can be locked f rom the
outsidebyusingthekeyineither
f ront door. To unlock only the driver’s
door f rom the outside, insert the key
in the driver’s door lock, turn the key
and release it. If you turn the key
and hold it, all doors will unlock. All
f our doors will unlock when you
unlock the passenger’s door with the
key.
Power Door L ocks
Keys and Locks
Inst rument s and Cont rols78
M M
A
AS
STTE
ER
R D
DO
OO ORR L
LOOC CKK S
SWWI ITT C
CH H L
LOOC CKK T
TA
A B
B
01/09/28 19:37:50 31SZ3660_081

If you f orget and leave the key in the
ignition switch, Lockout Prevention
will not allow you to lock the driver’s
door. With the driver’s door open
andthekeyintheignition,both
master door lock switches are
disabled. However, if the driver’s
door is not open, the master door
lock switches are not disabled.
Pushing the switch down on the
open passenger’s door will lock all
doors. If you try to lock an open
driver’s door by pushing in the lock
tab, the tabs on all doors pop out.
Pushinginthelocktabonthe
passenger’s door only locks that door.The ceiling lights (if the ceiling light
switch is in the center position) and
the door courtesy lights will come on
when you press the UNLOCK button.
If you do not open any door, the
lights stay on f or about 10 seconds,
then f ade out. If you relock the doors
with the remote transmitter before
10 seconds have elapsed, the lights
will go of f immediately.
You can lock and unlock your car
with the remote transmitter. When
you push the LOCK button, all doors
lock. You will hear a beep, and the
parking lights, taillights and license
plate lights will f lash once. When you push the UNLOCK button
once, only the driver’s door unlocks.
The remaining doors unlock when
you push the button a second time.
You will hear two beeps, and the
outside lights will f lash twice, each
time you push the button.
CONT INUED
Remote TransmitterL ockout Prevent ion
Keys and Locks
Inst rument s and Cont rols79
L LE
E D
D
U
UN NLLOOC CKK
B
BU UT TT
TO
ON N L
LO
OC CKK
B
BU UT TT
TO
ON N
T
T R
RU UN NKK
R
RE EL
LEE A
A S
SEE
B
BU UT TT
TO
ON N
P
P A
A N
NI ICC
B
BU UT TT
TO
ON N
01/09/28 19:38:00 31SZ3660_082

If you unlock the doors with the
remote transmitter, but do not open
any of the doors within 30 seconds,
the doors automatically relock and
the security system sets.
You cannot lock any of the doors
with the remote transmitter if any
door is not f ully closed or the key is
in the ignition switch. You cannot
unlock any of the doors with the key
in the ignition switch.
To open the trunk, push the Trunk
Release button f or approximately
one second.
You can open the trunk with the
remote transmitter regardless of the
position of the main switch in the
glove box. The trunk will not open if
the key is in the ignition switch.You can program the keyless entry
system so it does not beep when you
lock and unlock the doors. This
procedure only turns of f the beep;
the exterior lights will still f lash.
To turn this feature off, stand near
the car with the remote transmitter.
Press and hold the Trunk Release
button, then press the Lock button
within one second. You should see
the LED on the remote transmitter
come on f or one second. Release the
buttons af ter the LED goes out.
To turn this feature on, repeat the
above procedure. You should see the
LED blink twice.
Af ter you program the remote
transmitter, make sure the trunk lid
is closed.Panic mode allows you to remotely
activate your car’s security system to
attract attention. When activated, the
horn will sound, and the exterior
lights will f lash, f or about 30 seconds.
To activate panic mode, press and
hold the PANIC button for about two
seconds.
To cancel Panic mode bef ore 30
seconds, press any button on the
remote transmitter. You can also
turn the ignition switch to ON (II).
Panic mode will not activate if the
ignition switch is in the ON (II)
position.T urning t he Beep Of f and On
Panic Mode
Keys and Locks
Inst rument s and Cont rols80
01/09/28 19:38:11 31SZ3660_083

µ
Pull up or push down on the f ront of
the switch to move the seat bottom’s
f ront edge up or down. Pull up or
push down on the rear of the switch
to move the rear of the seat bottom
up or down.
Push the horizontal switch forward
or backward to move the seat
forward or backward. The long horizontal switch adjusts
the seat bottom in several directions.
The short vertical switch adjusts the
seat-back angle.
Make all seat adjustments bef ore
you start driving.
Your Acura has power adjustments
f or both f ront seats. The two power
seat adjustment switches are on the
outside edge of the seat bottom.
You can adjust the power seats with
the ignition switch in any position.
See pages f or important saf ety
inf ormation and warnings about how toproperly position seats and seat-backs. 12 14Driver’s Seat Adjustments
Seat A djustments
Inst rument s and Cont rols86
01/09/28 19:39:16 31SZ3660_089

Adjust the outside mirrors with the
adjustment button on the driver’s
door armrest:Turn the ignition switch ON (II).
Move the selector switch to L
(driver’s side) or R (passenger’s
side).
Keeptheinsideandoutsidemirrors
clean and adjusted f or best visibility.
Be sure to adjust the mirrors bef ore
you start driving.
The inside mirror has an automatic
anti-glare mechanism. When the
AUTO switch is pushed in, the
indicator will light. When the mirror
senses light f rom the headlights of
the car behind you, the mirror
surf ace will automatically darken to
reduce the glare.1.
2.
CONT INUED
A djusting the Power Mirrors
Mirrors
Inst rument s and Cont rols91
S SE
EL
LEE C
CT TO
OR R S
SWWI ITT C
CH H
O
ON
N S
STTA
A R
R
I
IN ND DI
ICCA A T
TO
OR R
A
A
N
NT TI
IG
GL LAA R
REE
I
IN ND DI
ICCA A T
TO
OR R
A
A N
NT TI
IG
GL LAA R
REE S
SWWI ITT C
CH H
01/09/28 19:40:01 31SZ3660_094

The outside mirrors are heated to re-
move fog and frost. With the ignition
switchON(II),turnontheheaters
by pressing the button. The light in
the button comes on as a reminder.
Press the button again to turn the
heaters off.
When you f inish, move the
selector switch to the center (off)
position. This turns of f the
adjustment button so you can’t
move a mirror out of position by
accidentally bumping the button.
Move the mirror right, left, up or
down by pushing the adjustment
button in that direction. Outside mirror positions can be
stored in the driving position
memory system (see page ). 4.
3. 93
Mirrors
Inst rument s and Cont rols92
H H
E
EA
A T
TE
ED
D M
MI
IRRR ROOR R B
BUUT TT
TO
ON N
A
A D
DJ
JUUS STTM
M E
EN
NT T B
BUUT TT
TO
ON N
01/09/28 19:40:09 31SZ3660_095