Acura TL 2013 Owner's Manual

Slide the new wiper blade into the
holder until the tabs lock.
Slide the wiper blade assembly
onto the wiper arm. Make sure it
locks in place.
Lower the wiper arm down against
the windshield, the passenger’s
side first, then the driver’s side.
Remove the blade f rom its holder
by grabbing the tabbed end of the
blade. Pull up f irmly until the tabs
come out of the holder.
Examine the new wiper blades. If
they have no plastic or metal
reinf orcement along the back
edge, remove the metal
reinf orcement strips f rom the old
wiper blade, and install them in
the slots along the edge of the new
blade.
Disconnect the blade assembly
fromthewiperarmbypushingin
the lock tab. Hold the lock tab in
while you push the blade assembly
toward the base of the arm.
When replacing a wiper blade,
make sure not to drop the wiper
blade or wiper arm down on the
windshield.
3.
5.
4. 6.
7.
2.
Wiper Blades
Maint enance
567
BLADE
BLADE REINFORCEMENT STRIP
LOCK TAB
12/07/20 11:43:12 31TK4640_572
2013 TL

To saf ely operate your vehicle, your
tires must be the proper type and
size, in good condition with adequate
tread, and correctly inf lated.
The f ollowing pages give more
detailed inf ormation on how to take
care of your tires and what to do
when they need to be replaced.Keeping the tires properly inf lated
provides the best combination of
handling, tread lif e, and riding
comf ort.
The tire pressure monitoring system
(TPMS) warns you when a tire
pressure is low. See page f or
more inf ormation on the TPMS.Underinf lated tires wear unevenly,
adversely affect handling and fuel
economy, and are more likely to
fail from being overheated.
Overinf lated tires can make your
vehicleridemoreharshly,are
more prone to damage f rom road
hazards, and wear unevenly.
514
Tires
Inf lation Guidelines
568
Using tires that are excessively
worn or improperly inflated can
cause a crash in which you can
be seriously hurt or killed.
Follow all instructions in this
owner’s manual regarding tire
inflation and maintenance.
12/07/20 11:43:19 31TK4640_573
Maint enance
2013 TL

Even though your vehicle is
equipped with TPMS, we
recommend that you visually check
your tires every day. If you think a
tire might be low, check it
immediately with a tire gauge.
Use a gauge to measure the air
pressure in each tire at least once a
month. Even tires that are in good
condition may lose 1 to 2 psi (10 to
20 kPa, 0.1 to 0.2 kgf /cm ) per
month. Remember to check the
sparetireatthesametime.Check the air pressures when the
tires are cold. This means the
vehicle has been parked f or at least 3
hours, or driven less than 1 mile (1.6
km). Add or release air, if needed, to
match the recommended cold tire
pressures on the
nextpage.
If you check air pressure when the
tires are hot [driven for several
miles (kilometers)], you will see
readings 4 to 6 psi (30 to 40 kPa, 0.3
to 0.4 kgf/cm ) higher than the cold
readings. This is normal. Do not let
air out to match the recommended
cold air pressure. The tire will
be underinflated. While tubeless tires have some
ability to self -seal if they are
punctured, you should look closely
for punctures if a tire starts losing
pressure.
You should get your own tire
pressure gauge and use it whenever
you check your tire pressures. This
will make it easier for you to tell if a
pressure loss is due to a tire
problem and not due to a
variation between gauges.
Tires
Maint enance
569
12/07/20 11:43:24 31TK4640_574
2013 TL

The following chart shows the
recommended cold tire pressures f or
most normal driving conditions.Thecompactsparetirepressureis:
For convenience, the recommended
tire sizes and cold tire pressures are
on a label on the driver’s doorjamb.
For additional technical information,
see page .
619
Cold Tire Pressure for
Normal Driving
Tire Size Tire Size
Cold Tire Pressure for
Normal Driving
Tire Size Cold Tire Pressure forNormal Driving
Tire Size Cold Tire Pressure for
Normal Driving
SH-AWD and SH-AWD with TechnologyPackage models
TL and TL with Technology Package models
TL with Advance Package and SH-AWD with Advance Package and
Canadian SH-AWD Elite PackagemodelsRecommended Tire Pressures
Tires
570
60 psi (420 kPa , 4.2 kgf/cm)
32 psi (220 kPa ,
2.2 kgf/cm
)
32 psi (220 kPa ,
2.2 kgf/cm
)
P245/45R18 96V P245/50R17 98V
32 psi (220 kPa ,2.2 kgf/cm
)
32 psi (220 kPa ,
2.2 kgf/cm
)
34 psi (235 kPa ,2.4 kgf/cm
)
P245/40R19 94V
34 psi (235 kPa ,2.4 kgf/cm
)
32 psi (220 kPa ,
2.2 kgf/cm
)
32 psi (220 kPa ,
2.2 kgf/cm
)
P245/45R18 96V
Rear: Front:
Rear:
Front:
Rear:
Front:
Rear: Front:
12/07/20 11:43:39 31TK4640_575
Maint enance
C
an ad ia n E lit e Pack ag e m od els
2013 TL

Every time you check inf lation, you
should also examine the tires for
damage, f oreign objects, and wear.
Youshouldlookfor:Bumps or bulges in the tread or
side of the tire. Replace the tire if
youfindeitherof theseconditions.
Cuts, splits, or cracks in the side
of the tire. Replace the tire if you
can see f abric or cord.
Excessive tread wear.
We strongly recommend that you do
not drive faster than the posted
speed limits and conditions allow. If
you ever drive in a sanctioned
competitive event at sustained high
speeds, be sure to adjust the cold tire
pressuresasshownbelow.If youdo
not, excessive heat can build up and
cause sudden tire f ailure.
Tire pressure f or high speed driving
is the same as f or normal driving. For speeds over 99 mph or 160
km/h:
For speeds over 112 mph or
180 km/h:
CONT INUED
Tire Size Cold Tire Pressure for High Speed Driving Tire Size Cold Tire Pressure for
High Speed Driving
TL with Advance Package, CanadianElite Package, SH-AWD, and SH-AWDwith Technology Package models SH-AWD with Advance Package
andCanadian SH-AWD Elite Packagemodels
TL and TL with
Tires
High Speed Driving T ire Inspection
Maint enance
571
P245/45R18 96V
32 psi (220 kPa ,2.2 kgf/cm
)
35 psi (240 kPa ,
2.4 kgf/cm
) 39 psi (270 kPa ,
2.7 kgf/cm
)
39 psi (270 kPa ,
2.7 kgf/cm
)
P245/40R19 94V
Front:
Rear: Front:
Rear:
12/07/20 11:43:52 31TK4640_576
Technology Package models
2013 TL

Your tires have wear indicators
molded into the tread. When the
tread wears down, you will see a 1/2
inch (12.7 mm) wide band across the
tread. This shows there is less than
1/16 inch (1.6 mm) of tread lef t on
the tire.
A tire this worn gives very little
traction on wet roads. You should
replace the tire if you can see three
or more tread wear indicators.The service lif e of your tires is
dependent on many f actors,
including, but not limited to, driving
habits, road conditions, vehicle
loading, inf lation pressure,
maintenance history, speed, and
environmental conditions (even
when the tires are not in use).
In addition to your regular
inspections and inf lation pressure
maintenance, it is recommended that
you have annual inspections
perf ormed once the tires reach f ive
years old. It is also recommended
that all tires, including the spare, be
removed from service after 10 years
from the date of manufacture,
regardless of their condition or state
of wear.
The last f our digits of the TIN (tire
identif ication number) are f ound on
the sidewall of the tire and indicate
the date of manufacture (See
on page ).619
Tires
Tire
Labeling
Tire Service Lif e
572
INDICATOR LOCATION MARKS
TREAD WEAR INDICATOR
12/07/20 11:43:59 31TK4640_577
Maint enance
2013 TL

CONT INUED
Replace your tires with radial tires of
the same size, load range, speed
rating, and maximum cold tire
pressure rating (as shown on the
tire’s sidewall).
Mixing radial and bias-ply tires on
your vehicle can reduce braking
ability, traction, and steering
accuracy. Using tires of a dif f erent
size or construction can cause the
ABS and vehicle stability assist
system (VSA) to work inconsistently.
The ABS and VSA system work by
comparing the speed of each wheel.
When replacing tires, use the same
size originally supplied with the
vehicle. Tire size and construction
can af f ect wheel speed and may
cause the system to activate.
To help increase tire lif e and
distribute wear more evenly, rotate
the tires according to the
maintenance messages displayed on
the multi-information display. Move
the tires to the positions shown in
the illustration each time they are
rotated. If you purchase directional
tires, rotate only front-to-back.
When the tires are rotated, make
sure the air pressures are checked.
In addition to proper inf lation,
correct wheel alignment helps to
decrease tire wear. If you f ind a tire
is worn unevenly, have your dealer
check the wheel alignment.
Have your dealer check the tires if
you f eel a consistent vibration while
driving. A tire should always be
rebalanced if it is removed f rom the
wheel. When you have new tires
installed, make sure they are
balanced. This increases riding
comf ort and tire lif e. For best results,
have the installer perform a dynamic
balance.
Tires
Replacing T ires and Wheels
Tire Rotation
T ire Maintenance
Maint enance
573
Front Front
(For Non-directional
Tires and Wheels) (For Directional
Tires and Wheels)
Improper wheel weights can damage
your vehicle’s aluminum wheels. Use
only Acura wheel weights f or balancing.
12/07/20 11:44:08 31TK4640_578
2013 TL

Î
Î
Î
Î
Î
It is best to replace all f our tires at
thesametime.If thatisnotpossible
or necessary, replace the two f ront
tires or two rear tires as a pair.
Replacing just one tire can seriously
af f ect your vehicle’s handling.
If you ever replace a wheel, make
sure that the wheel’s specif ications
match those of the original wheels.
Also be sure you use only TPMS
specif ic wheels. If you do not, the
tire pressure monitoring system will
not work.
Replacement wheels are available at
your dealer. See page f or DOT tire quality
grading inf ormation, and pagef or tire size inf ormation.
Wheels:
Tires:
: Advance Package and Canadian Elite Package
617
619
On 2WD Models
On SH-AWD Models
On 2WD Models
On SH-AWD Models
Wheel and T ire Specif ications
Tires
574
17x8.0J
18x8.0J
18x8.0J
19x8.0J
P245/50R17 98V
P245/45R18 96V
P245/45R18 96V
P245/40R19 94V (TPMS)
(TPMS) (TPMS)
(TPMS)
Installing improper tires on your
vehicle can affect handling and
stability. This can cause a crash
in which you can be seriously
hurt or killed.
Always use the size and type of
tires recommended in this
owner’s manual.
12/07/20 11:44:17 31TK4640_579
Maint enance
2013 TL

Ì
´
Î
Î
CONT INUED
This tire chain is available at many
auto supply stores. To f ind a local
storethatcarriesthechain,call
Quality Chain Corp at 1-800-843-8824.
To order the tire chain online, go to
, and enter
your vehicle inf ormation. When you
install the chains, f ollow the
manuf acturer’s instructions, and
mount them as tightly as you can.
Drive slowly with the chains installed.
Rubber chain adjusters, or tensioners,
must be used to prevent the chains
from contacting the body or the chassis.
If you mount snow tires on your
vehicle, make sure they are radial
tires of the same size and load range
as original tires. Mount snow tires on
all f our wheels. The traction
provided by snow tires on dry roads
maybelowerthanyouroriginaltires.
Check with the tire dealer f or
maximum speed recommendations.
Mount tire chains on your tires when
required by driving conditions or
local laws. Install them only on the
f ront tires. Do not use chains on the
rear tires.
Because your vehicle has limited tire
clearance, we strongly recommend
using this Quality Chain Corp. tire
chain:
Tires marked ‘‘M S’’ or ‘‘All
Season’’ on the sidewall have an all-
weather tread design suitable for
most winter driving conditions.
For the best perf ormance in snowy
or icy conditions, you should install
snow tires or tire chains. They may
be required by local laws under
certain conditions.
:
www.qualitychaincorp.com
Tires
Premium Cobra Cable Chain
1042P with accessory
adjusters
Winter DrivingSnow T ires
T ire Chains
Maint enance
575
12/07/20 11:44:26 31TK4640_580
2013 TL

Clean the wheels as you would the
rest of the exterior. Wash them
with the same solution, and rinse
them thoroughly.
Aluminum alloy wheels have a
protective clear-coat that keeps the
aluminum f rom corroding and
tarnishing. Cleaning the wheels with
harsh chemicals (including some
commercial wheel cleaners) or a stif f
brush can damage the clear-coat. To
clean the wheels, use a mild
detergent and a sof t brush or sponge.
If you ever hear the chains
contacting the body or chassis, stop
and investigate. If the chains have
loosened, retighten them. Make sure
they do not contact the brake lines
or suspension.
Removethechainsassoonasyou
begin driving on cleared roads. Wheels
Tires
576
Using the wrong chains, or not
properly installing chains, can
damage the brake lines and
cause a crash in which you can
be seriously injured or killed.
Follow all instructions in this
owner’s manual regarding the
selection and use of tire chains.
Traction devices that are the wrong
size or improperly installed can
damage your vehicle’s brake lines,
suspension, body, and wheels. Stop
driving if they are hitting any part of
the vehicle.
12/07/20 11:44:32 31TK4640_581
Maint enance
2013 TL