page 51 AUDI Q2 2021 Owner´s Manual

System settings

CO

< o rN
iv
rN
•-i

00
Sound effects
SeLect and confirm a setting for Focus:
-
all:
All the loudspeakers in the vehicle are ac­
tive (evenly distributed sound focus).
- front: Only the loudspeakers in the front of the
vehicle are active.
- rear*: Only the loudspeakers in the rear of the
vehicle are active.
Surround level
You can adjust the surround sound by turning the
rotary pushbutton.

Subwoofer*

You can adjust the subwoofer by turning the ro­
tary pushbutton.
Speed-dependent volume control
You can adjust the automatic volume adaption to
the interior noise level by turning the rotary
pushbutton.
Volume settings
Adjusting the volume
Using the
ON/OFF
button, you can adjust the
vol­

ume of
an
audio source or system message (e.g.
during a speech dialogue*) directly while it is be­
ing played.
- Volume up/down: Turn the ON/OFF button
(T)
^>page
152, Fig. 141 clockwise or
anti-clock­

wise.

- Mute/pause: Briefly press the ON/OFF button.
Or: Turn the ON/OFF button anti-clockwise un­
til the
sy m bol @ •=>
page 161 appears. Any ac­
tive audio/video source will then be paused.
- Unmute/resume: Briefly press the ON/OFF but­

ton.
Or: Turn the ON/OFF button clockwise.

Â
WARNING
The audio system volume should be set at a
level which enables you to hear external
sig­

nals (such as the sirens of police and emer­
gency vehicles)
clearly-failure
to do so could
result in an accident.
When you switch on the MMI system, very
high/very low volume levels are automatically
reduced/increased to a preset level.
Setting the system volume

•
Select:
|MENU|
button > Sound > left control

button.

Telephone
Applies to: vehicles with telephone
Mute telephone: Message and ring tones are si­

lenced.

Ring tone: Refer to
^>page
188, Ring tone and
volume settings.
Ring tone volume: You can adjust the volume of
the ring tone currently selected by turning the ro­
tary pushbutton.
Message volume: You can adjust the volume of
the tone informing you of
a
new message by
turning the rotary pushbutton.
Microphone input level: You can adjust the tele­
phone volume during a call by turning the rotary
pushbutton.
Navigation
Applies to: vehicles with navigation system
Voice guidance: Refer to
^>page
218.
Voice guidance during calls: Refer to

•=>
page 218.
Volume of spoken cues: You can adjust the
vol­

ume of the spoken cues by turning the rotary
pushbutton. Or: You can adjust the volume of the
spoken cues while route guidance is active by
turning the ON/OFF button.
Entertainment fader: This option allows the
vol­

ume of the current audio source to be temporari­
ly reduced when the parking aid is active or while
a navigation cue is being played.
Announcements*
Traffic announcements: Refer to
^>page
229.
DAB announcements*: Refer to
^>page
229. •
261

System settings
Volume of announcements: You can adjust the
volume of traffic announcements by turning the
rotary pushbutton.
Speech dialogue system

Applies
to: vehicles with speech dialogue system
Command display: Refer to
<=>page
256.
Short dialogue: Refer to
^>page
256.
Volume: Refer to
^>page
256.
Individual speech training: Refer to
^>page
256.
Parking
aid*

You can adjust the volume of the sounds by
turn­

ing the rotary pushbutton.
- To adjust the front volume: Select and confirm

high,
medium or low.
- To adjust the rear volume: Select and confirm

high,
medium or low.
MMI touch*
You can adjust the volume of the MMI touch*
spoken cues by turning the rotary pushbutton.
Restarting the MMI
system

_

Fig.
207 Combination of buttons for restart

•
Briefly press the rotary pushbutton and
simul­

taneously press the two buttons for calling up
menus directly upwards
^>Fig.
207.
Notes on software
Licences
Information on the MMI system's software and
its licence conditions
- Select:
|MENU|
button > Settings > left control
button > System maintenance
>
Version infor­

mation.

- Or: On the Internet at www.audi.com/softwar-

einfo.

Information on the head-up display's software
and its licence conditions
- Important: The vehicLe must be stationary.
- After switching on the ignition, press and hold
the button for the head-up display for at least
five seconds
<P.

- Press the rotary pushbutton to close the infor­
mation box. Or: Drive off.
Information on the instrument cluster's soft­
ware and its licence conditions
Press the reset button
(£) ^>page
12, Fig. 4 twice
in the first five seconds after switching on the ig­

nition.

262

Safe driving
Safe driving
General notes
Safety is the first priority
The safety features in your vehicle are harmon­
ised to provide you and your passengers with the
best possible protection in accident situations.
However, they can only be effective if you and
your passengers sit in the correct position and
adjust and use the safety equipment properly.
For these reasons, this chapter explains why
these safety features are so important, how they
can protect you, what you need to remember
when using them, and
how
you and your passen­
gers can gain the most benefit from them. There
are also a number of important safety warnings
which you and your passengers should always ob­
serve in order to minimise the risk of injury.
WARNING
- The information in this chapter is important
for the driver of the vehicle and all passen­

gers.
The other chapters in this manual

(and,
where applicable, in the other litera­
ture supplied with the vehicle) contain fur­
ther important notes which you should read
and observe for your own safety and that of
your passengers.
- Ensure that the complete vehicle wallet is
always in the vehicle. This is especially im­
portant when you lend or sell the vehicle to
others.

CO

<
O
rN
iv
rN
i—i
o < 00
Before every trip
The driver is responsible for the safety of the
passengers and the safe operation of the vehicle
at all times.

For
your own safety and the safety of your pas­
sengers, always note the following points before
every trip:

•
Make sure that all lights and turn signals are
working properly.

•
Check the tyre pressures.

•
Make sure that all windows are clean and give
good visibility to the outside.

•
Secure all luggage and other items carefully

•=>
page 272.
• Make sure that no objects can interfere with
the pedals.

•
Adjust the front seat, head restraint and mir­
rors correctly.
• Applies to: adjustable head restraints: Make
sure that the front passenger's head restraint is
adjusted to the correct position.
• Applies to: adjustable head restraints: Make
sure that the head restraints for the rear pas­
sengers are in the fully raised position.

•
Make sure that children are protected with suit­
able safety seats and properly worn seat belts

•=>
page 267.

•
Sit in the correct position in your seat. Make
sure
that
your passengers are sitting in the cor­
rect positions
^>page
58.

•
Fasten your seat belt correctly. Make sure that
your passengers do the same
^page
275.
What factors can impair your safety?
Safety on the road is directly related to
how
you
drive, and can also be affected by the passengers
in the vehicle.
• The driver is responsible for the safety of the
vehicle and all its occupants. If your ability to
drive is impaired in any way, you endanger
yourself and other road users
,=>^.
Therefore:
• Do not let yourself be distracted by passengers
or by using a mobile phone, etc.

•
Never drive when your driving ability is im­
paired (by medication, alcohol, drugs, etc.).
• Obey all traffic regulations and speed limits
and always maintain a safe distance to the
vehi­

cle in front.

•
Always adjust your speed to suit the
road,
traf­
fic and weather conditions.

•
Take frequent breaks on long trips. Do not drive
for more than two hours without a stop.

•
If possible, avoid driving when you are tired or

stressed.
•
263

Safe driving

CO
<
O
rN
iv
rN
•-i

00
Correct sitting positions
Correct driving position

The
correct driving position is important for safe
driving.
25cm

Fig.
208 Adjust seat and sit in correct position
For your own safety, and to reduce the risk of in­
jury in the event of an accident, we recommend
the following driving position.

•
Adjust the driver's seat and steering wheel so
there is a distance of at least 25 cm between
your breastbone and the centre of the steering

wheel
o>F/g.
208.

•
Adjust the height and fore/aft position of the
driver's seat so that you are able to press the
pedals to the floor without fully straightening
your legs
oA.

•
Adjust the backrest to an upright position so
that your back remains in contact with the up­
holstery.

*•
Adjust the longitudinal position of the steering
wheel so that your arms are slightly bent and
you can read the dials and instruments easily.

•
Make sure that you can comfortably reach the
top of the steering wheel.

•
AppLies to adjustable head restraints: Adjust
the head restraint so that the top of the head
restraint is
level
with the top of your head. If
this is not possible, try to adjust the head re­
straint as near as possible to this position.

•
Fasten your seat belt correctly
^>page
275.

•
Keep both feet in the footwell so that you are in
full controL of the vehicle at all times.
For detailed information on how to adjust the
driver's seat, see
^>page
58, Front seats.
A WARNING
A driver who is not sitting in the correct
posi­

tion or who is not wearing a seat belt can be
fatally injured
if
the airbag is triggered.
- Adjust the driver's seat and steering wheel
so there is a distance of at least 25 cm be­
tween your breastbone and the centre of the
steering wheel
^>Fig.
208.
-While driving, always hold the steering
wheel with both hands on the outside of the
rim at about the 9 o'clock and 3 o'clock
posi­

tion.
This reduces the risk of injury if the
driver's airbag inflates.
- Never hold the steering wheel at the 12
o'clock position, or with your hands inside
the rim or on the steering wheel hub. This
could result in serious injuries to the arms,
hands and head if the driver's airbag in­

flates.

- To reduce any risk of injury to the driver dur­
ing a sudden brake application or in an
acci­

dent, never drive with the backrest tilted
too far back. The airbag system and seat
belts can only provide proper protection
when the backrest is in an upright position
and the driver is wearing the seat belt in the
correct position. The further the backrest is
tilted back, the greater the risk of injury due
to incorrect positioning of the belt webbing
or an incorrect sitting position.
- Adjust the head restraint properly so that it
can give maximum protection.
Correct position for the front passenger

The
front seat passenger must sit at least 25 cm
away from the dash panel so that the airbag has
enough room to inflate and give maximum pro­
tection in an accident.
For your own safety and to reduce the risk of in­
jury in the event of
an
accident, we recommend
adjusting the front passenger's seat as follows:

•
Adjust the backrest to an upright position so
that your back remains in contact with the up­
holstery.

•
Adjust the head restraint so that the top of the
head restraint is level with the top of your
265

Safe driving

head.
If this is not possible, try to adjust the
head restraint as near as possible to this
posi­

tion.

•
Keep both feet in the footwell in front of the
seat.

•
Fasten your seat belt correctly
^>page
277.
In exceptional cases you can disable the front
passenger's airbag via the key-operated switch*

^>page
288.
For detailed information on how to adjust the
front passenger's seat, see
^page
58, Front
seats.
A WARNING
A passenger who is not sitting in the correct
position or who is not wearing a seat belt can
be fatally injured if the airbag is triggered.
- Adjust the front passenger's seat so there is
a distance of at least 25 cm between your
breastbone and the dash panel.
- Always keep your feet on the floor when the
vehicle is moving; never rest them on the in­
strument panel, out of the window or on the
seat. If
you
sit in an incorrect position, you
increase your risk of injury in the event of
sudden braking or an accident. If the airbag
is triggered, you could sustain potentially
fatal injuries by sitting out of position.
- To reduce the risk of injury to the front pas­
senger in the case of sudden braking or an
accident, the passenger should never travel
in a moving vehicle with the backrest re­

clined.
The airbag system and seat belt can
only provide proper protection when the
backrest is in an upright position and the
passenger is wearing the seat belt in the
correct position. The further the backrest is
tilted back, the greater the risk of injury due
to incorrect positioning of the belt webbing

or
an incorrect sitting position.
- Always adjust the head restraints properly
for maximum protection.
Correct position for rear passengers
Rear seat passengers should sit upright with
both feet on the floor and wear their seat belts
properly whenever the vehicle is moving.
To reduce any risk of injury in the event of sudden
braking or an accident, passengers in the rear
seats must observe the following:

•
Before carrying passengers on the rear seats,

puLl
the head restraints on the occupied seats
all the way up
^>page
59.
• Keep both feet in the footwell in front of the
rear seat.

•
Fasten your seat belt correctly
^page
278.

•
Use appropriate child restraint systems for
chil­

dren travelling in the vehicle
^>page
267.

/K
WARNING
Rear passengers sitting out of position can
suffer severe injuries.
- Always adjust the head restraints to the
fully raised position for maximum protec­

tion.

- Seat belts only offer maximum protection
when the backrest is in an upright position
and the passengers are wearing the seat
belts properly. By not sitting upright, rear
passengers increase the risk of injury due to
incorrect positioning of the seat belt web­

bing.

Correct adjustment of head restraints
Properly adjusted head restraints are an
impor­

tant part of the vehicle's occupant protection
system.
They
can help to reduce the risk of inju­
ries in most accident situations.

Fig.
209 Head restraint (seen from the front)
266

Safe driving

CO

< o rN
iv
rN
t-H
o < 00
The head restraints must be adjusted properly to
provide maximum protection.

•
Adjust the front head restraints so that the top
of the head restraint is level with the top of
your head. If this is not possibLe, try to adjust
the head restraint as near as possibLe to this

position.

•
Before carrying passengers on the rear seats,

pull
the head restraints on the occupied seats
all the way up
^>page
59.
For more information on how to adjust the head
restraints, see
^page
58.
A WARNING
- Travelling with the head restraints removed
or incorrectly adjusted increases the risk of
severe injuries.
- Incorrectly adjusted head restraints can also
increase the risk of injury during sudden or
unexpected braking or other manoeuvres.
Examples of incorrect seating positions
Occupants can suffer
severe
or fatal injuries if
they sit in an incorrect position while the vehicle
is moving.
Seat belts can only provide maximum protection
if the belt webbing is positioned correctly. Sitting
out of position greatly reduces the effectiveness
of the seat belts and increases the risk of injury
since the belt webbing is not worn in the position
for which it is designed. The driver is responsible
for the safety of all vehicle occupants, especially
for children.

•
Never allow anyone to sit out of position while
the vehicle is moving
•=>
A..
The following list shows just some examples of
incorrect sitting positions which can be danger­
ous to all occupants. The List is not complete, but
will help to make you aware of possible dangers
which can be avoided.
Therefore, whenever the vehicle is moving:
- Never stand up in the vehicle.
- Never stand on the seats.
- Never kneel on the seats.
- Never travel with the backrest reclined too far.
- Never lean against the dash panel.
- Never lie down on the rear seat.
- Never sit on the front edge of
a
seat.
- Never sit sideways.
- Never lean out of the window.
- Never put your feet out of the window.
- Never put your feet on the dash panel.
- Never put your feet on the seat cushion.
- Never ride in the footwell.
- Never travel on a seat without wearing the seat
belt.
- Never climb into the luggage compartment.
WARNING
Sitting out of position increases the risk of se­
vere injuries.
- Sitting out of position exposes the occu­
pants to potentially fatal injuries if, for in­
stance, the airbags inflate and strike an oc­
cupant who is not seated in one of the prop­
er positions.
- Before starting a trip, sit in the correct
posi­

tion and stay in this position as Long as the
vehicle is moving. Before every trip, make
sure all passengers are sitting in the correct
positions and remain correctly seated at all
times
^page
58, Front seats.
Child seats
Safety notes for using child seats

To
reduce the risk of injury in the event of
an
ac­
cident, children must always use child restraint
systems when travelling in the car.
Please note the information in this Owner's
Man­

ual when installing and using child seats. Follow
the manufacturer's instructions and observe any
statutory requirements.
For safety reasons, we recommend that child
seats be installed on the rear seats. You should
only use a child seat on the front passenger seat
in exceptional circumstances. •
267

Safe driving
A WARNING
To avoid serious or fatal injury, children trav­
elling in the vehicle must always be protected
with child restraint systems appropriate to
their height, weight and age.
- Children under 1.50 m tall or younger than
12 must not travel in the vehicLe if there are
no suitable child seats. Please observe any
other applicable regulations in the country
in which you are travelling.
- Babies and children must never travel on an­
other occupant's lap.
- Never allow more than one child to occupy
one child seat.
- Never leave a child without supervision in a
child seat.
- Never allow a child to travel unrestrained or
to stand up or kneel on a seat while the car
is moving. In an accident, the child could be
catapulted through the car, causing possibly
fatal injuries to itself and other occupants.
- To ensure proper protection by the child re­
straint, it is important to wear the seat belts
in the correct position
^>page
277. Always
check that the belt is properly positioned ac­
cording to the instructions provided by the
manufacturer of the child seat. Incorrectly
worn seat belts can give rise to injuries even
in a minor collision.
- If children are out of position when the car
is moving, they are at greater risk of injury
during a sudden braking manoeuvre or in an
accident. This is particularly the case if the
child is travelling on the front passenger's
seat and the airbag system is triggered in an
accident. This incorrect sitting position can
result in serious or even fatal injury.
- Make sure there is sufficient clearance in
front of the child sitting in the child seat. If
necessary, adjust the seat position and
backrest angle of the seat in front of the
child seat.
- If
you
are using a child seat on the front
passenger seat in which the child faces the
direction of
travel,
you should move the
front passenger seat as far back as possible.
- Child seats in which the child faces the rear
of the car are located directly in the path of
the front passenger's airbag if it inflates. In
this case, the child could sustain serious or
fatal injuries if the airbag were to be de­

ployed.

- Applies to vehicles on which the front pas­
senger's airbag cannot be deactivated: Do
NOT use a rearward-facing child seat on
the front passenger's seat.
- Applies to vehicles with key-operated
switch for deactivating the front passeng­
er's airbag: Do NOT use a rearward-facing
child seat on the front passenger's seat
while the front passenger's airbag is ac­

tive.
If
you
have no alternative but to use a
rearward-facing child seat on the front
passenger's seat, the front passenger's
airbag must be deactivated beforehand via
the key-operated switch*
^>page
288.
Make sure that the front passenger's air-
bag is reactivated by means of the key-op­
erated switch* as soon as the child seat is
no Longer needed on the front passenger's
seat.
- Always replace the child seat with a new one
after an accident as damage not externally
visible may have occurred.
Child seat categories
Only
use
child restraint systems that are official­
ly approved and suitable for the child.
2/3

Fig.
210 Weight categories for child seats
268

Safe driving

CO

<
O
rN
iv
rN
t-H
o < 00
Child restraint systems are regulated by Europe­
an standards ECE
R
44 or ECE-R
129x).
Both
standards apply in parallel. An orange label is
normally attached to child seats which have been
tested in accordance with these standards. Infor­
mation on weight categories, ISOFIX size class
and the approval category of the child seat can
be found on this Label.
Weight categories for child seats
- Child seats: categories 0 and 0+: Rearward-
facing carry cots are most appropriate for these
categories (up to 13 kg). Our recommendation:
Audi carry cot with optional ISOFIX base.
- Child seats: category 1: In this category (9 to
18 kg), rearward or forward-facing child seats
with an integrated seat belt system are most
appropriate. Rearward-facing child seats
should be used for as long as safely possible.
Our recommendation: Audi child seat with ISO-
FIX base.
- Child seats: categories 2 and 3: Child seats
with backrests used in conjunction with seat
belts are most appropriate for these categories
(15 to 36 kg). Our recommendation: Audi child
seat "youngster plus".
Approval categories for child seats
Child seats can have the approval categories
uni­

versal,
semi-universal, vehicle-specific (all ac­
cording to the ECE-R 44 standard) or
i-Size
(ac­
cording to the ECE-R 129 standard).
- Universal: Child seats approved for the univer­
sal category are suitable for installation in any
vehicle. A model list is not required. Universal
category child seats for ISOFIX anchorages
must be secured additionally by
a
top tether

strap.

- Semi-universal: Safety appliances requiring ad­
ditional tests are required for securing a child
seat with semi-universal approval. Child seats
with semi-universal approval have a model list
which must include your vehicle.
-Vehicle-specific: Vehicle-specific approval re­
quires that the child seat undergo a separate

1)
The ECE-R 129 standard has not yet been implemented by
the national authorities in all countries.
dynamic test for each vehicle model. Child
seats with a vehicle-specific approval also have
a model List.
- i-Size: Child seats with
i-Size
approval must
comply with the installation and safety require­
ments specified in the ECE-R 129 standard.
Your child seat manufacturer can inform you
which child seats with
i-Size
approval are ap­
propriate for your vehicle.
A WARNING
- Rearward-facing child seats: Never install a
rearward-facing child seat on the front pas­
senger's seat unless the front passenger's
airbag has been deactivated - this can result
in potentially fatal injuries to the
child.
If
you have no alternative but to let
a
child
travel on the front passenger's seat, the
front passenger's airbag must be deactiva­

ted*
beforehand
^>page
288.
- Forward-facing child seats: The back of the
child seat should be flush with the backrest
of the vehicle seat. If the rear head restraint
obstructs you when installing the child seat,
adjust or remove it completely
^>page
59.
Install the head restraint again immediately
after removing the child seat. Adjust the
head restraint to the correct height for the
passenger. Travelling with the head re­
straints removed or incorrectly adjusted in­
creases the
risk
of severe injuries.
- Categories 2 and 3: The shoulder section of
the belt must be fitted across the centre of
the child's collar bone close to the torso. It
must never run against or across the neck.
The lap belt must be worn tightly across the

hips,
and not over the stomach or abdomen.
Pull the belt tight if necessary to take up
any slack.
- Wait for as long as possibLe before changing
up to the next child seat group.
© Note
We recommend child seats from the range of
Audi Genuine Accessories: www.audi.com.
269

Safe driving
Fitting child seats
Securing child seats with ISOFIX

Fig.
211 Securing child seat with ISOFIX
If
you
wish to attach an ISOFIX child seat or i-
Size child seat to the ISOFIX anchorages in your
vehicle, please ensure that it is approved for the
seats in your vehicle. The following table
•=>
table
on page 270 shows the installation options. The
necessary information can be found on the or­
ange label on the child seat.
• Remove the covers* from the two ISOFIX an­
chorages.

•
Push the mountings on the child seat into the
ISOFIX anchorages until they engage audibly

=»
Fig.
211.

• PuLl
on the child seat to check whether both
sides have engaged properly.

•
If possibLe, secure the child seat additionally to
the top
tether1^
anchorage
^>page
271.
Child seat
Category 0:
up to 10 kg
Category 0+:
up to 13 kg
Category 1:
9 to 18 kg
ISOFIX
size cate­
gory
E
E
D
C
D
C
B

Bl

A
Outer
rear seats
IL
IL
IL
IL

IL,
IUF

IL,
IUF

IL,
IUF
Front

passeng­

er's seat*
IL
IL
IL
Child seat
Category 2:

15 to
25 kg
Category 3:
22 to 36 kg

i-Size
child
seat
ISOFIX
size cate­
gory
-
-
-
Outer
rear seats
IL
IL
i-U
Front

passeng­

er's seat*
IL
IL
X
- Size category: The size category specifies the
weight range for which the seat is approved. On
child seats with universal or semi-universal ap­

proval,
the size category is specified on the ECE
approval Label. Each child seat carries a label
specifying the weight category.
- IL: Seat suitable for the attachment of an ISO-
FIX child seat with semi-universal approval. Re­
fer to the list of vehicles provided by the child
seat manufacturer.
- IUF: Seat suitable for the attachment of
a
for­
ward-facing ISOFIX child seat with universal

approval.

- i-U: Seat suitable for the attachment of an i-
Size child seat with universal approval.
- X: Seat not suitable for the attachment of the
corresponding child seat.
WARNING
- Please refer to the important safety notes

•=>
A in Safety notes for using child seats on
page 268,
•=>
A In Child seat categories on
page 269 and the instructions provided by
the child seat manufacturer.
- Never install
a
rearward-facing child seat on
the front passenger's seat unless the front
passenger's airbag has been deactivated -
this can result in potentially fatal injuries to
the
child.

- The anchorages in the vehicle are designed
only for child seats with ISOFIX. Do not at­
tempt to secure other types of child seat,
seat belts or other objects to these ancho­
rages - this could result in serious or possi­
bly fatal injury.

l)
This function is not available for all export versions.
270

Safe driving
Securing child seats with ISOFIX and top
tether
Applies to: vehicles with top tether

â

I

Fig.
212 Rear backrest: Top tether anchorages (version 1)

7k

C

Fig.
213 Rear backrest: Top tether anchorages (version 2)

•
Adjust the head restraint behind the child seat
to the fully extended position.

•
Push the mountings on the child seat into the
ISOFIX anchorages until they engage audibly

^> page
270.

*•
Pull on the child seat to check whether both
sides have engaged properly.

•
Guide the top tether strap of the child seat un­
derneath or past both sides of the head re­
straint (depending on the type of child seat) to­
wards the rear.

•
Hook the strap into the top tether
anchorage15

=>
Fig.
212/o
Fig.
213.

•
Pull the tether strap tight so that the top of the
child seat rests securely against the backrest.
WARNING
- Please refer to the important safety notes

•=>
A in Safety notes for using child seats on
page 268,
•=>
A in Child seat categories on
page 269 and the instructions provided by
the child seat manufacturer.
- The anchorages in the vehicle are designed
only for one child seat with ISOFIX and top
tether. Do not attempt to secure other
types of child seat, seat belts or other ob­
jects to these anchorages - this could result
in serious or possibly fatal injury.

CO

<
O
rN
iv
rN
t-H
o < 00
Securing child seats with seat belt
If
you
wish to use a child seat in the approval cat­
egory "universal" (u), please ensure that it is ap­
proved for the seats in your vehicle. The follow­
ing table shows the installation options. The nec­
essary information can be found on the orange
label on the child seat.
Weight class
Category 0: Up to 10 kg
Category 0+: Up to 13 kg
Category 1: 9 to 18 kg
Category 2: 15 to 25 kg
Category 3: 22 to 36 kg
Front passenger's seat
Front passeng­
er's airbag on
X
X
X
u
u
Front passeng­
er's airbag off*
u
u
u
u
u
Outer rear seat
positions
u
u
u
u
u
Centre rear seat
u
u
u
u
u
X: Seat not suitable for the attachment of the
corresponding child seat.

1}
Two or three top tether anchorages are provided, depend­
ing on the equipment installed in your vehicle.
To adjust the front passenger's seat to the child
seat and to achieve the best possible seat belt •
271