engine AUDI Q2 2021 Owner´s Manual

Driving
This message appears
and a
buzzer sounds
if
you
open
the
driver's door while
the
engine
is
run­

ning.

Pressing start/stop button again will switch
off

engine.
This message appears
if
you press
the

ISTART
ENGINE
STOPI*
button while
the
vehicle
is moving
<^>page
77,
Emergency
Off
function.
Engine start system: fault. Please contact work­
shop
A fault
has
occurred when starting
the
engine
au­

tomatically (automatic start function). Drive
to a

qualified workshop soon
and
have
the
fault
recti­

fied.
To
start
the
engine, turn
the
ignition
key to

position
@
^>page
74 or
press

the
ISTART
ENGINE
STOPl
button and hold the

key/button until
the
engine starts.

D
Key not
recognised. See owner's manual
This message appears
if
there
is no
convenience
key inside
the
vehicle
or if
the system cannot
de­

tect
or
identify
the
key. This
can
happen,
for ex­

ample,
if
the radio signal from
the key is
obstruc­
ted
by a
metal briefcase
or
similar,
or if the key

battery
is
weak. Electronic equipment, such
as

mobile phones,
can
also interfere with
the
radio
signal from
the key.

The engine
can
still
be
started
or
stopped
if
this
happens (please refer
to
^page
79).

C]
Remote control key: hold back
of key

against marked area.
See
owner's manual
If
the
indicator lamp lights
up and the
message
appears,
a
malfunction
has
occurred

^>page
79.

3
Key not in
vehicle?

3
Remote control key:
key not
recognised.
Is

key still
in
vehicle?
If
the
indicator
lampGB
Lights
up and the
mes­
sage appears,
the
convenience
key
was removed
from
the
vehicle while
the
engine
was
running.
If

the convenience
key is not in the
vehicle
you
will
not
be
able
to
switch
on the
ignition
or
restart
the engine after
it has
been switched
off. You
will
also
not be
able
to
lock
the
vehicle from
the
out­

side.

Please press brake pedal
This message appears
on
vehicles with
an
auto­
matic gearbox
if
you
try to
start
the
engine
with­

out first pressing
the
brake pedal.
Please press clutch pedal
This message appears
if
you
try to
start
the en­

gine without first pressing
the
clutch pedal.
The

engine will only start
if
you press
the
clutch
ped­

al.

Please engage
N or P

This message will appear
if
you
try to
start
or

switch
off the
engine when
the
selector lever
is

not
in N or P. The
engine
can
then
not be
started
or switched
off.

Switch
off
ignition before leaving
car.
Battery
is

being discharged
This message appears
and the
buzzer sounds
if

you open
the
driver's door while
the
ignition
is

switched
on.
Switch
off
the ignition
to
prevent
the vehicle battery from being discharged.
Shift
to P,
vehicle can roll away. Doors can only
be locked
in P

For safety reasons, this message will appear
if

the selector Lever
of the
automatic gearbox
is not

in position P when
you
switch
off the
ignition.
Put

the selector lever
in
position
P;
otherwise
the ve­

hicle
can
roll away
and
cannot
be
locked.
78

Driving

CO

<
O
rN
IV
rN
t-H
o <
Starting the engine after
a malfunction

Applies
to: vehicles with convenience key
If the remote control key battery is exhausted or
if radio interference
or
a system malfunction oc­
curs, extra steps may be necessary in order to
start the engine.

Fig.
71 Steering column/remote control key: Starting the

engine
after a malfunction
If the message
D
Key not recognised. See
own­

er's manual or
|3
Remote control key: hold
back of key against marked area. See owner's
manual is displayed, you can still start the en­
gine manually.

•
Manual gearbox: Press the clutch
pedal

• Automatic gearbox: Press the brake pedal.

•
Hold the remote control key against the symbol

fJ)
^>Fig.
71, as shown in the illustration.
• Press the ISTART ENGINE
STOPl
button
^ A in

Starting the engine on page 76. The engine
shouLd start.

•
Drive to a qualified workshop soon and have the
fault rectified.
Note
You can call up the driver message again by
pressing the ISTART ENGINE STOP| button.
Start/stop system
Description

Applies
to: vehicles with start/stop system
The start/stop system can help to save fuel and
reduce
CO2
emissions.

1)
May vary in different countries
In start/stop mode, the engine is switched off
automatically when the vehicle stops, e.g. at
traffic lights. The ignition remains on during this
stop phase. The engine is automatically started
on demand.
The start/stop system is automatically activated
each
time
you switch on the ignition.
Basic conditions for start/stop mode
- The driver's door must be closed.
- The driver's seat belt must be buckled.
- The bonnet must be closed.
- The vehicle must have been moving at over 3
km/h since the Last stop.
CAUTION
Always switch off the start/stop system

^>page
81 before driving through water.
©
The engine is switched
off1)
shortly before the
vehicle comes to a stop. However, the brake
servo and power steering remain fully opera­

tional.

Stopping/starting the engine

Applies
to: vehicles with start/stop system

START
(M
STOP

S

Fig.
72 Instrument cluster: Engine switched off (stop

phase)

Applies
to: vehicles with manual gearbox

•
When the vehicle stops, put the gear Lever in
neutral and
take your
foot
off
the clutch pedal.
The engine will switch off. An indicator lamp

I
will light up in the instrument cluster •
79

Driving
display.
The rev
counter needle will also move

to
the
READY position.

•
The engine will start again automatically when
you press
the
clutch pedal.
The
indicator lamp
will
go out.

Applies to: vehicles with automatic gearbox

•
Brake
the
vehicle
to a
stop.
The
engine will
be

switched
off
shortly before
the
vehicle comes
to
a
standstill
or
when
the
vehicle
is
station-

aryx).
Keep your foot
on the
brake pedal.
The

indicator
lamp
@/
@
will appear
on the
dis­
play.
The rev
counter needle will also move
to

the READY position.

•
The engine will start again automatically when
you take your foot
off
the brake pedal.
If the

parking brake
is
applied
or
hold assist*
is

switched on,
the
engine will only restart when
you press
the
accelerator pedal1).
The
indicator
lamp
will
go out.

Further information
for
automatic gearboxes
The engine will stop
if
the selector lever
is in po­

sition
P, N or D.

The engine will start again
if
you move
the
selec­
tor lever
to
R during
a
stop phase.
If you
do not
want
the
engine
to
start when mov­
ing
the
selector Lever through
R,
move
the
lever
to P quickly.
You
can
control whether
or not the
engine
is

switched
off by
varying
the
amount
of
pressure
on
the
brake pedal.
For
instance,
if
you brake
gently
in
stop-and-go traffic
or
before turning
off

at a junction,
the
engine will remain
on
while
the

vehicle
is at
a standstill.
As
soon as you press
the

brake pedal harder,
the
engine will
be
switched

off.

be switched
off. The rev
counter needle will
move
to the
OFF position.
- Keep your foot
on the
brake pedal during
a

stop phase
to
prevent
the
vehicle from mov­

ing.

-
If you press the
ISTART ENGINE STOP|
but­

ton*
during
a
stop phase,
the
ignition will
Note
Applies to: vehicles with manual gearbox
If the engine stalls, you
can
start
it
again
di­

rectly
by
pressing
the
clutch pedal immedi­
ately.
General notes
Applies to: vehicles with start/stop system
Engine does
not
switch
off

The system checks that certain conditions
are

met before
and
during each stop phase.
If
the
in­

dicator lamp
Ey
appears
on the
instrument clus­
ter display,
the
engine will
not be
switched
off in

the following situations:
- The engine
has
not
yet
reached
the
minimum
temperature required
for
start/stop mode.
- The interior temperature selected
on the air

conditioner*
has
not
yet
been reached.
- The exterior temperature
is
very high/low.
- The windscreen
is
being defrosted
W.

-The parking
aid*
is
switched
on.

- The vehicle battery charge
is too low.

- The steering wheel
is
close
to
full lock
or the

vehicle
is
being steered.
- Reverse gear has just been selected.
- The vehicle
is on a
steep gradient.
-At high altitudes.
Engine cuts
in
again automatically
The stop phase
is
interrupted
in the
following sit­
uations,
for
example.
The
engine cuts
in
auto­
matically without intervention from
the
driver.
- The vehicle starts
to
roll (e.g.
on a
hiLl).

- The interior temperature deviates from
the air

conditioner setting.
- The windscreen
is
being defrosted
*$?.

- The brake pedal
is
pressed several times
in
suc­

cession.

- The vehicle battery charge drops
to an
insuffi­
cient level.

1'
May vary in different countries
80

Driving
- The power consumption is
high.

The engine switches off again when the condi­
tions for start/stop mode are once again
fulfil­

led1).

Ignition is switched off automatically
To prevent the vehicle battery from being dis­

charged,
the ignition will be switched off auto­
matically if certain conditions are met. For in­
stance:
- The start/stop system has switched off the en­

gine.

- The vehicle is stationary.
- The driver has left the vehicle.
If the dipped beam headlights are switched on in
this case, the side lights will be turned on in­

stead.
After approx. 30 minutes, or when you
lock the vehicle, the side Lights will be switched

off.

If the start/stop system has not stopped the en­
gine or if
you
have switched off the start/stop
system manually, the engine will continue
run­

ning and the ignition will not be switched off au­
tomatically
^A-

A WARNING
Never run the engine in confined spaces. The
exhaust gases are toxic - risk of poisoning!
© Note
If
you
select
D
or
N
after selecting reverse
gear on a vehicle with automatic gearbox, the
car must have been moving at over 10 km/h
before the system can switch off the engine

again.

Switching the start/stop system on/off
manually
Applies to: vehicles with start/stop system

You
can switch the system off manually if you
don't want to use it.
_.

rA^OFF

un
S
o
>
CO CO

Fig.
73 Centre console: Switch for start/stop system

•
To switch the start/stop system off or on
man­

ually, press the
\OE1
button. The LED in the but­
ton will light up when the system is switched

off.

© Note
If
you
switch off the system during a stop

phase,
the engine will start again automati­
cally.
Driver messages in the instrument cluster
display
Applies to: vehicles with start/stop system

H
Automatic
start/stop
deactivated: Please re­
start engine manually
This message appears if certain conditions have
not been met during the stop phase and the
start/stop system cannot start the engine again
automatically. In this case, the engine must be
started manually.

2]
Automatic
start/stop:
system fault! Func­
tion unavailable
There is a malfunction in the start/stop system.
Drive to a workshop soon and have the fault
recti­

fied.

CO

rN
IV
rN
t-H
o <
1)
May vary in different countries
81

Driving

Electro-mechanical

parking brake

•_ -_-

:c
2C

Fig.
74 Centre console: Button for parking brake and hold
assist
Your vehicle is equipped with an electro-mechan­
ical parking brake
(l)
^>Fig.
74. The parking brake
replaces the conventional handbrake, and is
mainly intended to prevent the vehicle from
roll­

ing away accidentally.
Applying/releasing the parking brake
manually
• To apply the parking brake, pull the button (®).
The LED in the button will light up. In addition,
the warning lamp || will light up in the instru­
ment cluster.

•
To release the parking brake manually, press
the brake or accelerator pedal with the ignition
switched on and simultaneously press the but­
ton
©).
The LED in the button and the warning
lamp on the display will go out.
Releasing the parking brake automatically
Important: The parking brake must be applied
and the driver's door must be closed.

•
Accelerate in the usual way to drive off and re­
lease the parking brake automatically.
Further features and safety functions are availa­
ble for driving off, in addition to the automatic
parking brake release function
^>page
83,
Driv­

ing away from a standstill.
Preventing the parking brake from being
released automatically
In certain situations, e.g. on a steep hill or when
towing a trailer, you may wish to prevent the ve­
hicle from rolling back.

•
To prevent the parking brake from being re­
leased automatically, pull and hold the but­
ton ©) while you press the accelerator. The
parking brake will remain engaged and prevent
any tendency to roll back down the slope.

•
You can release the button
(®)
as soon as the
engine is delivering enough power to the
wheels.
Emergency braking function
You can use the emergency braking function in
emergencies or if the main brake system fails or
the pedal is obstructed.
•
PuLl
and hold the button
«EJ.

• The brakes will be released immediately if you
release the button
®
or press the accelerator.
If
you
pull and hold the button
(®)
while the
vehi­

cle is moving, this will initiate an emergency
brake application. The brakes are then applied
hydraulically at all four wheels. The effect is
simi­

lar to heavy braking
<=> /\.

To prevent the emergency braking function from
being used accidentally, a warning buzzer sounds
when the button
(®)
is operated. The brakes are
released immediately when you release the but­
ton (®) or press the accelerator.
Parking the car

•
Press the brake pedal to bring the vehicle to a

stop.

•
To apply the parking brake, pull the button
©).

• Automatic gearbox: Move the selector lever to
position P.
• Switch off the engine
•» A-
•
Manual gearbox: Engage first gear.

•
When parking on a hill or gradient, turn the
steering wheel so that the vehicle would roll in­
to the kerb if it did start to move accidentally.

A
WARNING
- Take care never to press the accelerator
pedal or release the clutch inadvertently if
a

gear is engaged or if the selector Lever is not
in position
P
or
N
(on automatic vehicles)
while the vehicle is stationary with the en­
gine running. The vehicle will otherwise
82

Driving
start moving immediately and could cause
an accident.
- You should only use the emergency braking
function in a real emergency, for example if
the brake system were to fail or if the brake
pedal were to be obstructed. If
you
use the
emergency braking function by activating
the parking brake switch, this has the same
effect as heavy braking. Please remember
that the ESC (and the integrated ABS, EDL
and traction control functions) is still sub­
ject to certain physical limits. In a corner or
in bad road or weather conditions an emer­
gency stop can cause the vehicle to skid or
lose steering control.
- It is not possible to apply the parking brake
if the electrical power supply fails. In this

case,
park the vehicle on a
level
surface and
select 1st gear (manual gearbox) or move
the selector lever to position
P
(automatic
gearbox) to prevent
it
from rolling. Obtain
professional assistance.
- Always take the key with you when leaving
your
vehide
- even if
you
only intend to be
gone for
a
short time. This is especially im­
portant if children are left in the car. They
might otherwise be able to start the engine,
release the parking brake or use power-op­
erated equipment such as the electric
win­

dows - this could lead to injuries.
- Do not leave anyone (especially children) in
the vehicle when it is locked. Locked doors
could delay assistance in an emergency, po­
tentially putting lives at risk.
© Note
Applies to: vehicles with automatic gearbox
You can apply the parking brake manually or
switch on the hold assist* when stopping at
traffic lights, etc. You do not then have to
hold the car with the brake pedal, as the
brakes will stop it creeping forward while a
gear is engaged in the automatic transmis­

sion.
When you drive off in the normal way,

co
the parking brake will be released automati-
<

° cally
and your vehicle will start moving

2 •=>
page 83. o < 00

O
Note
- Any slight noise which may be heard when
the parking brake is applied or released is
quite normal and no cause for concern.
- The parking brake runs an automatic test
cycle at regular intervals when the vehicle is

parked.
This may cause a slight noise, which
is normal.
- If the electrical power supply fails, it is not
possible to release the parking brake (if it
was applied) or to apply the parking brake
(if it was released)
•=> A-
Obtain professional
assistance.
Driving away from a
standstill
Various features and safety functions are availa­
ble for driving off, depending on the equipment
in your vehicle.
Hill starting with the parking brake applied
Important: The driver's door must be closed.

•
To drive off more easily on a slope, apply the
parking brake and drive off just as you usually

would.
The parking brake will be released auto­
matically, but not until there is enough power
at the wheels to make the vehicle move in the
desired direction.
Hill starting with the hill hold assist
The hill hold assist function makes it easier to
drive away on a slope.
Important: The driver's door must be closed and
the engine must be running.

•
To activate the hill hold assist, press and hold
the brake pedal for several seconds. The vehicle
must be on a slope and facing uphill.
When you release the brake pedal the braking
force will be maintained for
a
moment
^^
in
order to hold the vehicle and make it easier for
you to drive away. •
83

Driving
Driving off with the hold assist
Applies to: vehicles with hold assist
The hold assist helps the driver if the vehicle is
stationary for a Long period or very often, for in­
stance at traffic lights, on steep gradients or in
stop-and-go traffic.
Important: The driver's door must be closed and
the engine must be running.
• To switch the hold assist on/off, press the but­
ton
«59 © ^>page
82, Fig. 74,
•=»^.
The LED in
the button will light up or go out.

•
Once it detects that the vehicle has stopped,
the hold assist keeps the vehicle stationary. In
this case, a green indicator Lamp
^
Lights up in
the instrument cluster. You can now take your

foot
off the brake pedal.

•
Drive off in the normal way: the brake will be
released automatically and the vehicle will
start moving.
In certain situations, the hold assist transfers the
job of holding the vehicle to the parking brake.
As soon as the parking brake is holding the
vehi­

cle
still,
the warning lamp || appears in the in­
strument cluster. In addition, the LED in the ®)
button will light up.
Driver messages in the instrument cluster
display

P.]
Hold assist: unavailable
If this message appears, the hold assist is un­
available or the system requirements have not
been met.
A WARNING
Applies to: vehicles with hill hold assist
If
you
do not drive away immediately after re­
leasing the brake pedal, or if the engine

stalls,
the vehicle could start to roll back. You
should therefore immediately press the brake
pedal or apply the parking brake.
A WARNING
The intelligent technology in the hold assist*
and hill hold assist functions cannot defy the
laws of physics. Do not let the extra conven­
ience afforded by the hold assist* and hill
hold assist functions tempt you into taking
any risks when driving - this can cause
acci­

dents.

- The hold assist* and hill hold assist func­
tions cannot keep the vehicle stationary in
all conditions on a gradient (e.g. if the road
is slippery or icy).
- Always ensure that the vehicle is stopped
properly and safely - risk of accident!

(T)
CAUTION
Switch off the hold assist* function before
driving the vehicle into a car wash.

©
r
Note
Applies to: vehicles with automatic gearbox
When the hold assist* function is switched

on,
it stops the vehicle from creeping for­
wards when you take
your
foot off the brake

pedal.

Off-road driving
General notes
The functions of the electronic stabilisation
con­

trol (ESC) have been augmented to provide extra
assistance when driving off-road. The
ESC
off-
road mode can be activated in situations when it
would be advantageous for the wheels to lock, or
when a differential Lock would normally be re­
quired
^>page
146.
This Audi model is not an off-road vehicle, how­
ever. When driving off-road you are advised to
avoid tracks or terrain which are not suited to
the design of the car and your own driving skills
and experience. Do not take any risks.
After driving off-road
- After driving, remove any pieces of foliage or
other objects which may be caught in the radia­
tor grille, under the car or in the wheels. In par­
ticular, inspect the tyre treads for stones.
- Clean the bodywork and underside of the
vehi­

cle and check the underside for possible dam­

age.

- Remove dirt from the windows, headlight
len­

ses and number plates. •
84

Driving
R - Reverse gear
Reverse gear should only be engaged when the
vehicle is stationary and the engine is idling
^A-

To move the selector lever to position R, release
the selector Lever lock and at the same time
press the brake pedal.
N - Neutral
In this position, the gearbox is in neutral.
D/S - Drive/Sport (standard position for
driving forwards)
In selector Lever position D/S, the gearbox can be
operated in either the standard drive mode (D) or
in sport mode (S). To select sport mode (S), brief­
ly pull the selector lever back. The gearbox will
switch back to drive mode (D) if
you
pull the se­
lector lever again. The selected driving mode is
shown in the instrument cluster display.
In the standard drive mode (D), the gearbox au­
tomatically selects the best gear ratio. This de­
pends on the engine
load,
the road speed and the
driving style.
In Sport mode S, the gearbox makes full use of
the engine power. When accelerating the gear
shifts may be noticeable.
Press the brake pedal when moving the selector
lever from N to D/S if the vehicle is stationary or
at speeds below 2 km/h
o A-

E - Efficiency*
In efficiency mode
^>page
131, Audi drive se­

lect,
the gearbox selects the next gear at lower
engine speeds. Earlier upshifts give improved
fuel economy because the full power reserves of
the engine are not used.
In this mode, an
E
is shown on the instrument
cluster display instead of
a D
^>Fig.
75.

CO

< o rN
iv
rN
t-H
o < 00

A,
WARNING
- The car can roll away even if the ignition is
switched off.
- Never move the selector lever to
R
or P
when driving, as this could cause an
acci­

dent.
- In all selector lever positions (except P) the
vehicle must always be held with the foot
brake when the engine is running. This is be­
cause an automatic gearbox still transmits
power even at idling speed, and the vehicle
tends to "creep" - risk of accident!
- The accelerator pedal must on no account
be pressed inadvertently when a gear is en­
gaged with the vehicle stationary. The
vehi­

cle could otherwise start moving immedi­
ately (in some cases even if the parking
brake is engaged) and possibly cause an ac­
cident.
- Do not press the accelerator while selecting
a gear with the vehicle stationary and the
engine running, as this could cause an
acci­

dent.
- The driver should never get out of the
vehi­

cle when the engine is running and a gear is

engaged.
If
you
have to Leave your vehicle
while the engine is running, you must apply
the parking brake and engage the parking
lock P.
- To avoid accidents, apply the parking brake
and
put
the selector lever in position
P
be­
fore opening the bonnet and working on the
vehicLe with the engine running. Please ob­
serve the important safety warnings

^>page
295, Working on components in
the engine compartment.
© Note
- Audi drive select: You can select the sport
program for gear changes by activating the
dynamic mode
^>page
131. The instru­
ment cluster display will show
S
instead of
D.
- If the lever is moved accidentally to
N
when

driving,
take
your
foot off the accelerator
and
let
the engine speed drop to idling be­
fore selecting
D
or
S
again.
- It is not possible to move the selector lever
out of position
P
if the electrical power sup­
ply fails. In this case, the selector lever can
be released manually. Left-hand drive
vehicles
^page
93, right-hand drive
vehicles
<^>page
94.
87

Driving
©
y Note

If the selector lever does not lock automati­
cally, a malfunction has occurred. In this case,
the power transmission is interrupted to pre­
vent the vehicle from moving unintentionally.
Proceed as follows to engage the selector lev­
er lock again:
- Applies to vehicles with 6-speed gearbox:
Briefly press the brake pedal.
- Applies to vehicles with 7-speed gearbox:
Press the brake pedal. Move the selector
lever to position
P
or
N
and then select a
gear.
- If the vehicle does not move forwards or
backwards even though a gear is selected,
proceed as follows:
- If the vehicle does not move in the desired

direction,
the system may have failed to en­
gage the gear correctly. In this case, press
the brake pedal and select the gear again.
- If the vehicle still does not move in the de­
sired direction, a system malfunction has

occurred.
Seek professional assistance and
have the system checked.
General notes on driving an automatic
Applies to: vehicles with automatic gearbox

Fig.
77 Detail of the centre console: Selector lever with in­
terlock button
Starting the engine

•
Move the selector Lever to
P
or N. In the case of
Low outside temperatures (below -10 °C), the
engine can only be started when the selector
lever is in position P.
Driving away from a standstill

•
Press and hold the brake pedal.

•
Press and hold the interlock button (the button
in the selector lever handle), set the selector
lever to the desired position (e.g. D)
^>page
86
and release the interlock button.

•
Wait for the gearbox to engage the gear (a
slight movement can be felt).

•
Release the brake and press the accelerator
There are several convenient functions to help
you drive away on gradients
^page
83.
Stopping briefly

•
Press the brake pedal to hold the vehicLe when
stationary (for instance at traffic lights).

•
Do not press the accelerator.

•
To prevent the vehicLe from rolling away, apply
the parking brake before moving off on steep
gradients
•=>^
and
•=>(]).

• As soon as you acceLerate as normal, the park­
ing brake will automatically be released and
the vehicLe will start moving. Important: The
driver's door must be closed.
Stopping/parking the car
If
you
open the driver's door while the selector
lever is not in position P, the vehicle can roll
away. The message Shift to P, otherwise vehicle
can roll away. Doors do not lock if lever is not in
P. appears on vehicles with convenience key*. A
buzzer will also sound.

•
Press and hold the brake pedal
<=>
A..

•
Apply the parking brake.

•
Move the selector Lever to P.
In some situations (such as on mountain roads or
when towing a trailer or caravan) it can be advan­
tageous to switch temporarily to the manual
shift programme so that the gear ratios can be
selected manually to suit the driving conditions

^>page
90.
On level ground it is sufficient to move the selec­
tor lever to P. On a gradient the parking brake
should be applied first and the selector Lever
should be moved to
P ^>page
82. This reduces
the load on the locking mechanism and makes it
easier to move the selector lever out of position
P. •
88

Driving
A WARNING
- The driver should never get out of the
vehi­

cle when the engine is running and a gear is

engaged.
If you have to leave your vehicle
while the engine is running, you must apply
the parking brake and engage the parking
lock P.
-If the engine is running and a gear is engag­
ed (D/S or R) or the vehicle is in "tiptronic"

mode,
you will need to hold the car with the
footbrake. Otherwise, the car will "creep"
forwards as the power transmission is not
fully interrupted even when the engine is

idling.

- The accelerator pedal must on no account
be pressed inadvertently when the vehicle is
stationary. The vehicle could otherwise start
moving immediately (in some cases even if
the parking brake is engaged) and possibly
cause an accident.
- Do not press the accelerator while selecting
a gear with the vehicle stationary and the
engine running, as this could cause an
acci­

dent.
- Never move the selector lever to R or P
when driving at normal speeds, as this could
cause an accident.
- Before you drive down a steep gradient, re­
duce the speed and use "tiptronic" to select
a low gear.
- Never allow the brake to drag when driving
downhill and do not use the brake pedal too
often
or
for long periods. Constant braking
will cause the brakes to overheat and will
considerably reduce the effectiveness of the
brakes. It will increase the braking distance
and could cause the brake system to
fail.

- To avoid rolling back on gradients always
hold the vehicLe with the footbrake or park­
ing brake if you have to stop.
- Never attempt to hold the vehicle with the
clutch when stopping on a gradient. The
clutch is disengaged automatically if it is
overloaded and becomes too hot - accident
risk! If the clutch is overloaded, the indica­
tor lamp
0
will light up and a message will
appear
^>page
92.
© CAUTION
- When you have stopped on a gradient, do
not try to stop the vehicle rolling back by ac­
celerating when a gear is engaged. This
could cause the automatic gearbox to over­
heat and become damaged. Apply the park­
ing brake or press the brake pedal in order
to prevent the vehicle from rolling back.
- If you allow the car to roll with the selector
lever in position N with the engine switched
off, the automatic gearbox will be damaged
as it will not be lubricated
^page
328,
Tow-starting / towing
away.

- In certain driving and traffic conditions, for
instance in stop-and-go traffic, if you have
to pull away frequently or if the vehicle
creeps forwards over a long distance, the
gearbox can overheat and become dam­

aged.
If the indicator Lamp
[5J
or the warn­
ing
lampH
Lights up, stop the vehicle at
the first opportunity and let the gearbox
cool down
^>page
92.
© Note
For safety reasons the parking brake will only
release automatically if the driver's door is

closed.

Downhill speed control
Applies to: vehicles with automatic gearbox
The downhill speed control function helps the
driver when driving down steep gradients.
Downhill speed control is activated on a downhill
gradient when the selector lever is in D/S and the
driver presses the brake pedal. The gearbox auto­
matically selects a suitable gear for the gradient.
The downhill speed control function attempts to
maintain the speed at which the vehicLe was trav­
elling when the foot brake was applied (subject
to the laws of physics and technical limitations of
the power train). It may be necessary to adjust
the speed again using the foot brake. The down­
hill speed control can change down to 3rd gear
but no further, so it may be necessary to change
to tiptronic mode on very steep gradients. In this

case,
change down manually to 2nd or 1st gear in •
CO
89