mode AUDI Q2 2021 Owner´s Manual

Notes on this Owner's Manual
This Owner's Manual applies to all versions of
your particular Audi model and contains impor­
tant information, tips, suggestions and warn­

ings.

Please ensure that this Owner's Manual is always
kept in the vehicle. It should always be available
to anyone else driving the vehicle, i.e. anyone

renting,
borrowing or buying the vehicle from

you.

This manual describes the equipment available
for the vehicle at the time of going to print.
Some of the equipment described here will not
be available until
a
later date, or may only be
available in certain markets.
Some sections of this Owner's Manual do not ap­
ply to all vehicles. If this is the case, a text at the
start of the section indicates which vehicles it ap­
plies to, e.g. "Applies to: vehicles with cruise
con­

trol system". This optional or vehicle-specific
equipment is also marked with an asterisk "*".
Illustrations are intended as a general guide,
and may vary from the equipment fitted in your
vehicle.
All references to positions such as "left", "right",
"front" or "rear" are given as seen facing in the
direction of travel.
* Optional or vehicle-specific equipment
• The section is continued on the following

page.

•=>
A Refers to a "WARNING" within the same

section.
If the WARNING symbol is followed by a
page number the warning text referred to is in­
cluded in a different section.

/\
WARNING
Texts with this symbol contain safety infor­

mation.
They warn you of serious dangers,
possibly involving accident or injury.

(J) CAUTION

Texts with this symbol draw your attention to
a possible risk of damage to your vehicle.
® For the sake of the environment
Texts with this symbol refer to points relevant
to the protection of the environment.
® Note
Texts with this symbol contain additional in­
formation of
a
more general nature.
6

Instruments
and
controls

CO

<
o

IV
tN
I-I
00
Vehicles with manual gearbox
-
•
Shifting
up
a gear:
The
suggested gear
ap­

pears
to the
right
of
the current gear when
a

higher gear
is
recommended.
-
4
Shifting down
a
gear:
The
suggested gear
ap­

pears
to the
left
of
the current gear when
a

lower gear
is
recommended.
The gearyou
are
currently
in and the
recommen­
ded gear will
be
displayed. Gears
may
occasional­
ly
be
skipped
(3 • 5).

Vehicles with start/stop system:
If
all
the
condi­
tions
for
a
stop phase
^>page
79
have been
met,
but the
gear lever
is in
gear with
the
clutch

depressed,
the
gear change indicator will recom­
mend changing
to
•N.
Put the
gear lever
in
neu­

tral and take your foot
off
the clutch pedal.
The

start/stop system will automatically switch
off

the engine.
Vehicles with automatic gearbox
The display
is
only visible
in
tiptronic mode

^>page
90.

The symbol
Î
after
the
current gear means
change
up a
gear.
© CAUTION
The gear-change indicator
is
intended
to
help
save
fuel.
It is not
intended
to
recommend
the right gear
for all
driving situations.
In
cer­
tain situations, only
the
driver can choose
the

correct gear
(for
instance when overtaking,
driving
up
a steep gradient
or
towing a
trail­

er).

(T) Note

Applies
to:
vehicles with manual gearbox
The gear-change indicator
in the
instrument
cluster goes
out
when you press
the
clutch

pedal.

Outside temperature display
When
the
vehicle
is
stationary
or
travelling
at

very
low
speeds,
the
temperature displayed
may

be slightly higher than
the
actual outside
tem­

perature
as
a result
of
the heat radiated from
the

engine.
At temperatures below +5°C a snowflake symbol
appears next
to the
temperature display
<=> A-

A WARNING
Do
not
rely
on the
outside temperature dis­
play
as an ice
warning. Bear
in
mind that
there
may be
patches
of
ice
on the
roads even
at outside temperatures around
+5
°C
-
risk
of

accident!
Multi-function steering
wheel plus
How
to use the
multi-function steering
wheel
Applies
to:
vehicles with Audi virtual cockpit

You
can
use
the
multi-function steering wheel
to

control
the
driver information system
and MMI

functions, adjust
the
volume
and
switch
the

speech dialogue system
on/off.

»180km
1
&_J
f
87.6M...
|f
|
H

n

^
_
X

m

®r

87.6 MHz CI /
88.7 MHz
90.0 MHz
90.5
MHz

91.5
MHz

96.6 MHz

Fig.
7
Example: Driver information system display (Audi
virtual cockpit)

In

1-

m

Fig.
8
Left side
of
multi-function steering wheel plus
Important:
The
ignition must
be
switched
on.

15

Instruments and controls

-Totaljourney
memory summary
- Energy consumers
^>page
20
- Driver assistance
^>page
104
- Traffic sign recognition
<=>page
108
The single journey memory processes the infor­
mation on
a
journey from the time the ignition is
switched on until it is switched off. If the journey
is resumed within two hours after the ignition is
switched off, the new figures are automatically
included in the calculation.
Unlike the
single
journey memory, the totaljour-
ney memory is not erased automatically. In this
way, you can determine the period for which you
wish the on-board computer to supply driving in­

formation.

Fuel consumption
The current fuel consumption can be shown in a
bar display
^>Fig.
15. The average fuel consump­
tion from the single journey memory can also be

displayed.
If the barturns green, yourvehicle is
saving fuel using the following function:
- Recuperation: Electrical energy can be stored in
the battery (recuperation) if the vehicle is trav­
elling downhill or coasting in gear (overrun). In
this case, the bar will move towards the
Q

symbol.

- Active Cylinder Management*: The engine au­
tomatically shuts down two cylinders when per­
formance demand is low and certain other
con­

ditions have been met. This process is imper­
ceptible to the occupants. The driver message

2-cylinder
mode will appear if the average fuel
consumption display
^>Fig.
15 is selected in the
instrument cluster. The cylinders are reactiva­
ted under heavier load conditions.
Energy consumers*
In the Energy consumers view, auxiliary equip­
ment currently affecting the vehicle's fuel
con­

sumption is listed. The display shows up to
three energy consumers. The energy consumer
drawing the most power appears at the top of
the list. If more than three energy consumers are
switched on, the ones currently using the most
power are displayed. In addition, a scale
indi­

cates the overall current fuel consumption of all
energy consumers.
Economy tips
Applies to: vehicles with Audi drive select and efficiency mode
In efficiency mode, economy tips are shown
briefly on the instrument cluster display in cer­
tain situations where fuel economy is affected.
By following these economy tips, you can save

fuel.

To clear an economy tip from the display immedi­
ately, press the left thumbwheel on the multi­
function steering wheel.
To activate/deactivate economy
tips:
Select the
following on the infotainment system:
|MENU|

button > Car
>
Audi drive select. Select: efficien­
cy
>
right control button > Economy tips.
© Note
- The date, the time and the time/date dis­
play format can be changed via the infotain­
ment system
^page
255.
- The economy tips are not always displayed
in every conceivable situation, but are delib­
erately spaced out over time.
- Once you have cleared an economy tip from
the display, it will not appear again until the
next time you switch on the ignition.
On-board computer (analogue instrument
cluster)
Applies to: vehicles with analogue instrument cluster
15:50

0
6,0

Fig.
16 Instrument cluster: Consumption display
Resetting values to zero

•
Press the
[Hi
button on the multi-function
steering wheel and select On-board computer
or Efficiency program from the menu. •
20

Instruments and controls

CO

<
o

IV
tN
I-I
00
• To reset the figures in the selected memory to

zero,
press the left
thumbwheel (Î) •=>page
18,
Fig. 13 on the multi-function steering wheel for
one second.
Calling up vehicle functions
• Call up the first tab (on-board computer) using
the
0E]
button on the multi-function steering

wheel.

•
Press the
@
button on the multi-function
steering wheel and select Vehicle functions
from the menu.
The equipment installed on your vehicle deter­
mines which of the following displays are availa­

ble:

- On-board computer fl, B
opage
21
- Efficiency program
3
<^page
21
- Digital speedometer
- Assists
cépage
104
- Traffic signs
^>page
108
- Reduced display
On-board computer
On the on-board computer you can call up the
following displays in turn by scrolling the left
thumbwheel on the multi-function steering

wheel:

- Date
•=>
page 255
- Range
- AdBlue range*
^>page
292
-Short-term
memoryD

- Average fuel consumption
- Long-term memory B
The single journey memory processes the infor­
mation on
a
journey from the time the ignition is
switched on until it is switched off. If the journey
is resumed within two hours after the ignition is
switched off, the new figures are automatically
included in the calculation.
Unlike the single journey memory, the
total
jour­
ney memory is not erased automatically. In this
way, you can determine the period for which you
wish the on-board computer to supply driving in­

formation.

The following additional display may be available
in the on-board computer, depending on the ve­
hicle equipment:
- Active Cylinder Management: The engine auto­
matically shuts down two cylinders when per­
formance demand is low and certain other
con­

ditions have been met. This process is imper­
ceptible to the occupants. The driver message

2-cylinder
mode will appear if the current or
average fuel consumption display
oFig.
16 is
selected in the instrument cluster. The cylin­
ders are reactivated under heavier load condi­

tions.

Efficiency program
3

Applies to: vehicles with efficiency program
The efficiency program can help to save
fuel.
It
evaluates fuel efficiency data, shows a list of aux­
iliary equipment affecting fuel consumption, and
suggests gear changes. It also provides economy
tips for saving
fuel.

The efficiency program uses the trip and fuel
con­

sumption data from the short-term memory.
When you clear the data from the efficiency pro­

gram,
the values in the short-term memory are
reset to zero.
The following additional displays are available in
the efficiency program, depending on the vehicle
equipment:
- Advanced gear-change indicator: The advanced
gear-change indicator is based on the same
log­

ic as the "regular" gear-change indicator. The
"regular" gear-change indicator disappears
from the display when the advanced gear-
change indicator appears
^>page
14.
- Energy consumers: The efficiency program
shows a List of energy consumers currently af­
fecting the vehicle's fuel consumption. The dis­
play shows up to three energy consumers. The
energy consumer drawing the most power ap­
pears at the top of the list. If more than three
energy consumers are switched on, the ones
currently using the most power are displayed.
In addition, a scale indicates the overall current
fuel consumption of all energy consumers.
- Economy
tips:
Economy tips will automatically
appear intermittently in the efficiency program •
21

Instruments and controls
in certain situations. By following these econo­
my tips, you can save
fuel.
To clear an economy
tip from the display immediately, press any of
the controls on the multi-function steering

wheel.

The date, the time and the time/date display
format can be changed via the infotainment
system
•=>
page 255.
Radio
Important: Radio mode must be activated

^>page
228, and the radio/media tab must be

displayed.

•
Press the
HH
button or the left control button

^>page
16, depending on the equipment in
your vehicle.
The following functions are available on the driv­
er information system, depending on the vehicle
equipment:
- To set the waveband: Select and confirm the

waveband.

- To tune to a station from the memory list*:
Select Memory
>
desired radio station.
- To tune to a station from the station list*: Se­
lect and confirm a radio station.
- To tune to a station from the favourites list:
Select Favourites > desired radio station.
- To call up a media source: Select and confirm
To media.
Other settings
Applies to: vehicles with Audi virtual cockpit
- SeLect: right control button > desired
entry.

The following settings are available depending
on which function is selected:
- Update station list*: see
<=>page
232.
- Detailed station information: See

opage
232.
Media
Important: A media drive must contain audio/
video files
^page
235, and the radio/media tab
must be displayed.

•
Press the
\M
button or the left control button

^page
16, depending on the equipment in
your vehicle.
The following functions are available on the driv­
er information system, depending on the vehicle
equipment:
- To select a media source: Select and confirm a
media source, e.g. "SD
card".

- To play an audio/video file: Select and confirm
a track/file.
-To pause/resume playback: Press the right

thumbwheel (D^poge
17, Fig. 12. To continue
playback, press the right thumbwheel again.
- To restart playback of an audio file: Select the
track currently playing if it is not already selec­
ted and press the left thumbwheel.
Applies to: vehicles with analogue instrument cluster
- To switch to the radio: Select and confirm a
waveband (e.g. FM).
Applies to: vehicles with Audi virtual cockpit
- To switch to radio: Select and confirm To radio.
- To call up detailed track information: SeLect
the right control button > Detailed track infor­

mation.
For more information, please refer to

tapage
246.
® Note
- The MMI media drives do not support DRM-
protected files; these files are marked with
the
symbolS.

- Please note that when you are using the
driver information system to control play­
back within a media source, only the playlist
selected on the MMI control console can be
played
^>page
244.
- Always note the information on the info­
tainment display. It may be necessary to
use the MMI control console to operate cer­
tain functions.
22

Instruments and controls

fiP
Light sensor/rain sensor
Applies to: vehicles with light sensor/rain sensor

g
Automatic headlights/wipers: system fault!
The light sensor/rain sensor is out of action.
For safety reasons, the dipped beam headlights
will then be switched on permanently when the
light switch is set to the AUTO position. You can
still switch the lights on and off in the normal
way with the light switch. You can also continue
to use all the other wiper functions that do not
use the rain sensor.
Drive to a qualified workshop soon and have the
fault rectified.

9
Suspension control
Applies to: vehicles with suspension control

Q
Suspension: system fault!
There is a malfunction in the suspension control

system.

Drive to a qualified workshop soon and have the
fault rectified.

<£>OTurn
signals
If the indicator Lamp
H or H
flashes, the turn
signals are on. If both indicator lamps flash, the
hazard warning lights are on.
If one of the indicator lamps flashes twice as fast
as usual, a turn signal bulb has failed. Drive care­
fully to a qualified workshop without delay and
have the fault rectified.

«V
Trailer turn signals
Applies to: vehicles with towing bracket
If the indicator Lamp
E]
flashes, the turn signals
are on in towing mode.
If
a
turn signal bulb on the trailer or vehicle fails
in towing mode, the indicator lamp does not
flash twice as fast to indicate the bulb failure.
36

Lights and vision

CO

<
o
rN
iv
rN
t-H
o
< 00
The light* for the make-up mirror comes on auto­
matically when you slide open the mirror cover
©•
Windscreen wipers
Switching on the windscreen wipers

V

WJIO
*

Fig. 45
Windscreen
wiper
lever

m®

v
"trj-i

s
to
o > 03 m

Fig.
46 Control lever for rear wiper
Move the windscreen wiper lever to the appropri­
ate position:

@-Wipers
off
(Î) - Intermittent wipe. Move switch
®
to the Left
or to the right to increase or reduce the wiper de­
lay interval. If your vehicle is equipped with a rain
sensor*, the windscreen wipers will be activated
automatically in the rain as long as the vehicle
has been moving faster than approx. 4 km/h at
Least once. The higher the sensitivity level for the
rain sensor (i.e. the further switch
(Â)
is moved to
the right), the sooner the windscreen wipers re­
act to moisture on the windscreen. You can deac­
tivate the rain sensor mode on the infotainment
system (this will activate the intermittent wipe
mode). To do so, select: |MENU| button > Car >
left control button > Driver assist
>
Rain sensor.

@-
Slow wipe

(|)-
Fast
wipe
(?) - Single wipe. If
you
hold the lever in this
posi­

tion,
the wipers will switch from slow continuous
wiping to fast continuous wiping after
a
while.
(D - Wash/wipe. The screen is given an extra wipe
a few seconds later to remove any dribbles of wa­
ter (if the vehicle is moving and the temperature
is above approx. 4
°C).
You can deactivate this
function by moving the lever to position
(s)
again
within 10 seconds after the extra wipe. The ex­
tra-wipe function is activated again the next time
you switch on the ignition.
Headlight washers*. The headlight washer sys­

tem*
only operates when the dipped headlights
are switched on. The headlights are also auto­
matically washed intermittently when you move
the lever to position
(s).

(?) - Rear wipe. The rear window is wiped approxi­
mately every 6 seconds.
If the windscreen wipers are on and in operation,
the rear window wiper will also be switched on
automatically when you engage reverse gear.

©-
Rear wash/wipe. The number of wiper cycles
depends on how long you hold the Lever in
posi­

tion©.
A WARNING
- The rain sensor* is only intended to assist
the driver. The driver is still obliged to
man­

ually operate the windscreen wipers as re­
quired depending on visibility.
- Do not use water-repellent coatings on the
windscreen. In bad visibility conditions such
as light
rain,
low sun or when driving at
night these coatings can cause increased
dazzle, which is a serious safety hazard.
Such coatings can aLso cause the wiper
blades to judder.
- Poor visibility can cause accidents. Always
ensure that the wiper blades are in good
condition
^>page
56, Changing the
wind­

screen wiper blades.
55

Heating and cooling
Heating and cooling
Heating system/air
conditioner
Description
One of the following systems may be fitted, de­
pending on the equipment in your vehicle:
- Heating and ventilation system or
- Manual air conditioner* or
- Automatic air conditioner* (deluxe version)
The heating and ventilation system* heats and
ventilates the vehicle interior. The air condition­
er* additionally cools and dehumidifies the air in­
side the vehicle. It operates most effectively with
the windows and the panorama sun roof* closed.
If the vehicle has been standing in the sun, it may
cool down faster if
you
open the windows briefly
to let the hot air escape.
Pollution filter
The pollution filter removes impurities, such as
dust and pollen, from the air.
Key-coded settings
Various settings are stored and assigned to the
remote control key in use.
Default settings
Default settings for certain functions can be se­
lected on the infotainment system.
SeLect the following on the infotainment system:

|MENU|
button
>
Car
>
left control button
>
A/C.
Supplementary heater*
Applies to: vehicles with diesel engine
The vehicle interior warms up more quickly with
the supplementary heater. The system automati­
cally switches the supplementary heater on
tem­

porarily as required, depending on the setting on
the vehicle heating system.
The supplementary heater function can be
switched on or off as required. SeLect the follow­
ing on the infotainment system:
|MENU|
button >
Car
>
left control button
>
A/C
>
Auto supple­
mentary heater.
® For the sake of the environment
I

- Switch off the cooling mode on the air
con­

ditioner* by pressing the A/C button if you
wish to save
fuel.
This will also reduce emis­

sions.
The LED in the button will go out
when the air conditioner is switched off.
- On vehicles with efficiency program*, you
can see how your fuel consumption is being
affected by auxiliary equipment and have
tips for improved fuel economy displayed

•=>
page 21.
- Applies to vehicles with diesel engine: The
automatic supplementary heater function
can be switched off on the infotainment sys­
tem
cépage
66, Supplementary
heater*.

©
- Keep the air intake slots in front of the
windscreen clear of snow, ice and Leaves to
ensure unimpaired heating and cooling, and
to prevent the windows misting over.
- Condensation can drip off the air cooling

system*
and form a pool underneath the ve­

hicle.
This is normal and does not indicate a
leak.
- If
you
notice, for instance, that the seat* or
rear window heating is not working, it may
have been temporarily switched off by the
power management function. These sys­
tems will be available again as soon as
suffi­

cient electrical power is available.

l
) Note
The air conditioner contains fluorinated
greenhouse gases. Further information is pro­
vided on a sticker in the engine compart­

ment1^.

1'
May vary in different countries
66

Heating and cooling
Heating/ventilation system or manual air conditioner
Applies to: vehicles with heating/ventilation system or manual air conditioner

Fig.
65 Heating/ventilation system or manual air conditioner*: Controls

CO

<
O
rN
IV
rN
•-i

00
The functions can be switched on and off using
the buttons and controlled using the rotary
con­

trols.
The LED in the corresponding button lights
up when the function is switched on.
Manual air conditioner*
For
a
comfortable climate inside the vehicle us­
ing the air conditioner:
- In the summer, adjust the temperature to just
a few degrees below the outside temperature
- Do not turn the blower up too high
- Do not point the air outlets directly at the occu­
pants
A/C Cooling mode*
The air cooling system only works when the blow­
er is switched on. The air cooling mode is switch­
ed on/off when the A/C button is pressed. When
the air cooling is switched off, the air is not
cooled and therefore not dehumidified. The
win­

dows may mist up as a result. The air cooling is
switched off automatically at low outside
tem­

peratures.

#
/ # Temperature
Rotary control ® is used to adjust the tempera­

ture.

%
Blower
You can adjust the blower speed manually using

control®.
You should leave the blower on at a
low setting to prevent the windows from misting
up and to ensure that the vehicle interior is
con­

stantly ventilated. To demist the windows, we
recommend
that
you increase the blower speed
and set control ® to
<W.

W/
v?/
*JI
*J Air distribution and air
outlets
The rotary control ® can be used to adjust the
air distribution. A setting between
f£j
and
*J

usually provides a comfortable environment.
At the
^
setting, the windscreen and side
win­

dows are defrosted or demisted as quickly as pos­

sible.
The air recirculation is switched off, but can
be switched on again manually by pressing the

<s?
button.
The round air outlets in the dashboard can be ad­
justed
^page
71.
To prevent the front side windows from misting
up in wet weather, it's a good idea to open the
side air outlets and point them to the side.
Foot-level air outlets are provided underneath
the front seats to heat the rear cabin.
67

Heating and cooling

cS5
Air recirculation mode
In air recirculation mode, the air from the interi­
or of the vehicle is filtered and recirculated. This
setting prevents fumes etc. from entering the in­
terior. We recommend switching on the air recir­
culation mode when driving through a tunnel or
in traffic queues
•=>
A-
The air recirculation mode is switched off when
the control is in the defrost position
<ffl.

Qjp
Rear window heating
If the rear window heating is activated with the
ignition switched on, the battery management
determines whether or not the vehicle battery
charge level is sufficient for the rear window
heating to be switched on. Otherwise the rear
window heating operates when the engine is
run­

ning,
and switches off automatically after about
10 - 20 minutes, depending on the outside
tem­

perature.
To switch on the rear window heating perma­
nently, press and hold the
CÛJD
button for at least
2 seconds. This setting will be stored for approxi­
mately 15 minutes after the ignition is switched

off.

J
Seat heating*
When you press the
«0
button, the seat heating is
switched on at level 3 (the highest level). The
LEDs indicate the temperature level. To reduce
the temperature, press the button again. To
switch off the seat heating, press the button re­
peatedly until all the LEDs have gone out.
The seat heating automatically switches from
level 3 to level 2 after about 10 minutes.
(7) CAUTION
To avoid damaging the heating elements of
the seat heating, please do not kneel on the
seat or apply sharp pressure at
a
single
point

© Note
- The setting for the driver's seat heating is
assigned to the key in use.
- If the front passenger's seat heating was on
when you Last switched off the ignition, it
will be switched on automatically only if the
ignition is switched on again within 10 mi­

nutes.

/K
WARNING
- For reasons of safety you should not Leave
the air recirculation switched on for too

long.
This mode prevents fresh air from en­
tering the vehicle, so the windows can mist
over if the air cooling* is switched off. Bad
visibility can cause an accident.
- People with limited capacity to feel pain or
sense temperature could burn themselves
when using the seat heating. These people
must not use the seat heating - risk of in­
jury!
68