oil AUDI Q7 2012 Owner´s Manual

Page 109 of 342

-The brake booster and servotronic only
work when the engine is running. With
the ignition turned off, you have to apply
more force when steering or braking .
S ince you cannot steer and stop normal­
ly, this can lead to accidents and ser ious
injuries.
- The rad iator fan can continue to run for
up to 10 min utes even after you have
turned off the engine and removed the ign ition key. The radiator fan can also
turn on again if the engine coolant heats
up because of intense sunlight or heat
build -up in the engine compartment.
«I) Note
Do not stop the engine immed iate ly after
hard or extended dr iving. Keep the engine
running for approximately two minutes to
prevent excessive heat build-up .
Starting and stopping
the engine with
Convenience key
Starting the engine with the~
button
App lies to vehicles: with Convenie nce key
This bu tton swi tches on the ign ition and
starts the engine .
Fig. 121 Co nvenie nce k ey: ENG INE START b utton
The I S TAR T! button is provided w ith two -sta ge
o p era tion
¢ fig. 121.
Switching the ignition on
.. Press the !START I button once to the fir st
stage to switch on only the ign ition .
On th e road 107
Gasoline eng in e: St arting th e engine
.. Step on the brake.
.. Move the se lector lever to the P or N posi ­
tion ¢,&. .
.. Press the
r::1s=Tc:- A=RT =I button to th e seco nd
stage to start the engine .
Diesel en gine : Starting the engine
.. Step on the brake.
.. Mov e the selector lever to the P or N posi­
tion ¢,&. .
.. Press the
r::1s=TAc:-=R T=I button down to the fi rst
level to begin the preheating process . The
glow plug indica tor light &; illuminates
when the glow plug sy stem is active .
.. When the indicator light
m;J switches off,
press the
I S TA RT ! button down to the se c­
ond
level to start the eng ine .
After a cold engine is started, there may be a br ief period of increased no ise because oil
pressure must first build up in the hydraulic
valve adjuste rs. This is norma l and not a cause
for concern .
If the engine does not start immediately, stop
trying after 10 seconds and then try to restart
the engine abou t 30 seconds later .
Glow plug system *
Di ese l engine s
are equ ipped with a glow plug
system whose preheating time is controlled
by the coo lant and outs ide temperature . Start
the engine
immediately afte r the glow plug
indicator light
m switches off.
The glow plug indicator light will only illumi ­
nate fo r approximate ly 1 second when the en­
gine is warm or the outs ide temperature is
higher than 46 °F (8 °C) . That means yo u can
star t the eng ine
immediately .
WARNING
Never allow the engine to run in confined
spaces -danger of asphyxiation .
(D Note
-Avo id h igh engine rpm, full thrott le and
heavy engine loads until the eng ine has

Page 112 of 342

110 On the road
The parking brake warning light. (USA)/ .
(CON) illuminates when the parking brake is
set and you switch on the ignition.
_& WARNING
-
Always release the parking brake com­
pletely. A partially engaged brake will
overheat the rear brakes, reduce their ef­
fectiveness and cause excessive wear. This could lead to brake failure and an accident .
(D Note
Only after the vehicle has come to com­ plete stop, should you firmly set the park­
ing brake and move the selector lever into
"P".
Parking
To prevent a parked vehicle from rolling
away, there are a few things you should do .
When you park your vehicle, do the
following
• Stop the vehicle using the brake pedal.
• Apply the parking brake firmly .
• Move the selector lever into the
P position
~ &.
• Switch off the engine and remove the igni-
tion key from the ignition lock.
When you park your vehicle on hills, do
the following
• Stop the vehicle using the brake pedal.
• Apply the parking brake firmly.
• If you are parking headed downhill, turn
the front wheels
toward the curb.
• If you are parking headed uphill, turn the
front wheels
away from the curb.
• Move the selector lever into the
P position.
• Switch off the engine and remove the igni­
tion key from the ignition lock.
_& WARNING
This is how you can reduce the risk of in­
jury when leaving your vehicle. -
Never park the vehicle where it can come
in contact with dry grass, spilled fuel or
any other flammable materials.
- When parking on hills, always turn the
wheels so that the front wheels will first
roll into the curb, if the vehicle should
start to roll.
- Never allow anyone - especially small
children - to remain in the vehicle when
it is locked. locked doors make it more
difficult for rescuers to access the pas­
senger compartment in the event of an
emergency. Danger to life!
- Never leave children unsupervised in the
vehicle. Children could release the park­
ing brake or move the gearshift lever out
of gear. The vehicle could start to roll
away and cause an accident.
- No matter what the season is, the tem­
perature in a parked vehicle can reach
dangerous levels.
@ Note
-Please exercise care when you park your
vehicle in parking areas with parking bar­
riers or curbs. Parking barriers and curbs
vary in height and could damage your
bumper and related components as the
front of your vehicle moves over a barrier or curb that is too high, as you park or as
you back out of a parking spot. In order to be sure that no such damage can oc­
cur, you may wish to stop short of having
the front tires of your car touch the park­
ing barrier or curb.
- Please also exercise exceptional care
when you drive up or down steep ramps
or drive over curbs or other obstacles, for
which the vehicle is not designed, be­
cause components of the vehicle close to
the ground, such as bumper covers, spoilers and suspension and exhaust sys­
tem components, may become dam­ aged.
Starting on hills
Hill Hold makes it easier to start on hills.

Page 132 of 342

130 Audi side assist
-The radar sensor's vision can be reduced
or entirely blocked by rain, snow, and
heavy spray . This can result in side assist
not adequately detecting vehicles or, in
some cases, not detecting them at all.
Always keep an eye on the direction you
are traveling and the relevant area
around the vehicle.
- Please note that side assist indicates
there are approaching vehicles, or vehi­ cles in your blind spot, only after your ve­
hicle has reached a driving speed of at
least 19 mph (30 km/h).
- Side assist signal does not work around
tight corners (turning radius less than
328 feet, or 100 m).
- Side assist is no replacement for the driv­
er's full attention. The driver alone is re­
sponsible for lane changes and similar
driving maneuvers. Always keep an eye
on the direction you are traveling and the relevant area around the vehicle.
- To ensure that you do not adversely af­
fect side assist, do not block the area on
the rear bumper where the radar sensors
are located with foreign objects (such as
stickers or bicycle racks).
- Make sure that the signal light on the
outside mirror is not blocked by stickers
or other items.
(Di Tips
- Side assist automatically deactivates if it
detects that the radar sensors are
blocked ¢
page 135. The indicator light
on the button goes out .
- The area on the bumper where the radar
sensors are located must consistently re­
main free of snow, ice, and heavy soiling
so that side assist can function properly.
Follow the additional notes on
¢page 136.
-For vehicles with a factory installed tow­
ing hitch* or a trailer hitch* that was in­
stalled later according to factory specifi­
cations, side assist is automatically deac- tivated
as soon as the electrical connec­
tion to the trailer electrical socket is made
¢ page 135.
-For vehicles with a trailer hitch that was
not installed according to factory specifi­
cations, switch off the side assist when
towing a trailer .
- Additional tinting on the front side win­
dows can make it harder to see and cor­
rectly understand the signal light on the
outside mirror.
- For Declaration of Compliance to United
States FCC and Industry Canada regula­
tions¢
page 322.
Sensor detection area
Applies to vehicles: with side assist
-----··· .... ·--·--
@ / ,
--­
ill b''T -
Fig. 150 Sc hematic illustration: Sensor detectio n area
The detection ¢ fig. 150 of the radar sensor
detection area is made up of:
-
- the approach area (light red area) (D, about
230 feet (70 m) behind the vehicle, and
- the "blind spot" (dark red area) @.
The radar sensors cover the adjacent left and
right lanes. Other lanes are
not covered by the
radar sensors.
(D Tips
Side assist does not measure actual lane
width. The system assumes a fixed lane
width . Detection in the left and right lanes
is based on this assumed lane width.
When driving on narrow roads or when
driving to the left or right of the center of
a travel lane, it is possible that vehicles
will be detected that are
not in the lane

Page 225 of 342

-Before descending a steep grade, reduce
speed and shift transmiss ion into a lower
gear or lower driving range. Do not ride
the brakes or hold the pedal down too
long or too often. This could cause the
brakes to get hot and dimin ish braking
efficiency.
- Do not "r ide the brakes" by resting your
foot on the pedal when you do not intend
to bra ke. Th is may cause the brakes to
overheat, prema ture wear and increased
stopping distance .
- Under certain climat ic and operating
condit ions such as passing through wa­
ter, driving in heavy rain or after washing
the vehicle, the effectiveness of the
brakes can be reduced . In winter, ice can
accumulate on the brake pads, linings,
discs and drums. Carefully apply brakes
for a test . Brakes will dry and ice coat­
ings will be cleaned off after a few care­
ful brake applications.
- Driv ing for an extended period of time on
salt-covered roads w ithout us ing your
brakes can also affect braking efficiency .
Clean off accumulated salt coating from
brake discs and pads w ith a few caref ul
brake applicat ions.
- If you damage the front spoiler, or if you
install a different spoiler, be sure the air
flow to the front brakes is not obstruct ­
ed. Otherwise the brake system co uld
overheat reducing the effectiveness of
the entire brake system.
- Failure of one brake circuit will impair
the braking capability resulting in an in­
creased stopp ing distance. Avoid driv ing
the vehicle and have it towed to the near­
est author ized Audi dealer or qualified
workshop .
Brake booster
The brake booster adds extra braking power.
The brake booster works with vacuum pres­
sure which is created only when the engine is
running¢ &,.
Int ellig ent technolog y 223
A WARNING
-Never let the veh icle roll to a stop with
the engine shut off .
- If the brake booster is not working, for
example when towing your vehicle, or because the brake booster has somehow
been damaged, the brake pedal must be
pressed considerably harder to make up
for the la ck of booster assistance .
Functioning of Anti-Lock Brake System
(ABS)
ABS prevents the wheels from locking up un­
der braking.
T he ABS contributes effect ively to vehicle con­
trol s ince it preve nts the whee ls from
locking
when the brakes are applied. This means that
the vehicle remains steerable and is less likely
to skid .
With ABS y ou do not nee d to pump the
bra ke. Just h old t he br ake ped al d own .
However, do not expect the ABS to shorten
braking distance under
all circumstances.
When dr iving on g ravel or on new ly fallen
snow o n top of icy s urfaces, braking dis tance
may be even longer, therefore, under these
circumstances, it is especia lly important that
you drive s low ly and wit h great care.
How the ABS s ystem works
An a utomat ic check is made when a speed of
about 12 mph (20 km/h) is reached . When
th is happens, a pumping noise can be heard.
If an ind iv idual whee l begi ns to rotate too
s low ly in relation to vehicle speed and tends
to lock, the ABS automatically reduces brake
pressure to prevent tha t whee l from locking .
T his automatic adjustment p rocess will cause
a
sli ght vibrati on of the brake pedal and some
no ises to a le rt you that ve hicle speed m ust be
adapted to existing road and traffic condi ­
tions. •

Page 227 of 342

@ Tips
- When the engine is running, never hold
the steer ing whee l turned a ll the way to
the right or t o the left f or longer than 15
seconds . The power steering pump w ill
overheat the hydraulic f lu id if you keep
hol ding the steer ing wheel turned all the
way . This is likely to damage the power
steering system .
- If the power steer ing system should fail
ent irely, or if the engine is not running
(fo r example , while being towed), you
will still be able to steer the vehicle .
However ,
considerably more effort will
be required to do so.
- If the power s teer ing system should
have a leak, or is not f unct ioning proper ­
l y, contact yo ur authorized Audi deale r
immediately.
- The power stee ring system requires a
spec ially formulated hydraulic fl uid. The
power steer ing reservo ir is the one locat­
ed farthest to the rear on the left side of
the engine compartment
c> page 260.
The co rrect flu id leve l in the reservoi r is
i mportant for p roper functioning of the
power steer ing .
Driving with your
quattro ®
With all-whe el drive , oil four whe els ore driv ­
en.
General information
W ith all -whee l dr ive , power is dis tr ibuted to
a ll fo ur wheels. This happens automatica lly
dep ending on yo ur driving sty le and the road
conditions at th e time . See a lso
¢ pag e 221,
Electronic differential lock ( EDL) .
Winter tires
When driv ing in the w inter , your ve hicl e w it h
all -wheel drive has an advan tage, even with
regu lar tir es. In wint er road conditions it may
be adv isable to mount wint er tires (o r all -sea­
son t ires) for improved driveability and b rak-
Int ellig ent technolog y 225
ing: t h ese tires must be mounted on all four
wheels. See also ¢
page 289, Winter tires .
Tire chains
Where tire chains a re ma ndatory o n cer tain
roads, this no rma lly also app lies to veh icles
with all-wheel drive¢
page 290, Snow
chains.
Replacing wheels/tires
Vehicles with all-wheel drive must always have ti res of t he same s ize. A lso avo id tires
with different t read dep ths. For det ails see
page
c!;> pag e 285, New tir es and replacing
tires and wheels .
_& WARNING
A lways adj ust yo ur driv ing to road and traf­
f ic conditions. Do not let the extra safety
afforded by all-wheel drive tempt you into
taking extra risks .
-Altho ugh the all-wheel drive is very ef ­
fective, always remember that braking
capacity is lim ited by tire traction. You
should therefore not drive at excessive
speeds on icy or slippe ry road surfaces .
- On wet road surfaces, be careful not to drive too fast because the front wheels
could begin to slide o n top of the water
(aquaplaning). If th is should occur, yo u
will have no w arning from a s udden in­
cre ase in engine speed as w ith a front ­
wheel drive veh icle. Always drive at
speeds which are su ited to the road con­
ditions -risk of crash.
Energy management
Starting ability is optimized
E nergy management controls the distribution
of electrical energy and thus optimizes the
availability of electrical energy for starting the engine.
If a vehicle with a conventiona l energy system
is not drive n for a long per iod of t im e, the bat­
te ry is discharged by idling cur rent consume rs
(e .g. immobi liz e r) . In cert ain circum stan ces it ..,_

Page 231 of 342

Catalytic converter
Applies to vehicles: with gasoline engine
It is very important that your emission con­trol system (catalytic converter) is function­
ing properly to ensure that your vehicle is run­
ning in an environmentally sound manner .
... Always use lead-free gasoline¢ page 250,
Gasoline .
... Never run the tank down all the way to
empty .
... Never put too much motor oil in your en-
gine ¢
page 264, Adding engine oil~-
.,. Never try to push- or tow-start your veh icle.
The catalytic converter is an eff icient "clean­
up" device built into the exhaust system of
the vehicle. The catalytic converter burns
many of the poll utants in the exhaust gas be ­
fore they are released into the atmosphe re.
The exclusive use of unleaded fuel is cr it ically
i mportant for the life of the cata lytic convert­
e r and proper fu nctioning of the engine.
A WARNING ,~
- Do not park or operate the veh icle in
areas where the hot exhaust system may
come in contact with dry grass, brush,
fuel spill or other material which can
cause a fire.
- Do not apply additional undercoating or
rustproofing on or near the exhaust
man ifold, exhaust p ipes, catalytic con­
verter or heat shie lds . During driving, the
substance used for undercoating could
overheat and cause a fire.
{[) Note
-Be aware that just one tank fi lling with
le aded fuel will already seriously de­
grade the performance of the catalytic
conve rter .
- Do not exceed the correct engine oil level
¢ page 264.
-Do not drive until the fuel tank becomes
completely empty. The eng ine could mis­
fire . U nburned fuel could a lso get into
Dri vin g and en vironm ent 229
the exhaust system and this cou ld cause
the catalytic converter to overheat .
- Do not turn off the igni tion while the ve ­
hicle is moving.
- Do not con tinue to ope rate your veh icle
unde r these conditions, as othe rwise fuel
can reach the catalytic converter. This
co uld result in overheating o f the con­
verter, requir ing its replacement.
- To assure efficient operation of the Emis ­
sion Control System:
- H ave your vehicle maintained prope rly
and in accordance w ith the se rv ice rec­
ommendat ions in you r Warranty &
M ain tenance boo klet.
- L ack of prope r maintenance as we ll as
improper use of the vehi cle w il l impair
the function of the em ission contro l
system and could lead to damage .
@ For the sake of the environment
Even when the Emiss io n Control System is
operat ing properly, the exha ust gas can
have a sul fur -li ke exhaust gas smell under
some operating states . This depends on
the sulfur content of the fuel being used .
Using a different brand of fue l may help,
or f illing the tank with lead-free super
grade gasoline .
Diesel particulate filter
Applies to vehicles : with diese l eng ine
The diesel part ic u late filter filters nearly all of
the soot particles out of the exhaust . The fil­
ter cleans itself automat ica lly under normal
driv ing cond itions . If the filter ca nnot clean it­
self (for example, because you a re o nly dr iving
short distances), the fi lter becomes clogged
with soot and the. symbo l for the diesel
particu late filter ill uminates ¢
page 3 7.
A WARNING
- Do not park your vehicle over flammable
materia ls such as grass or leaves because
the high temperature of the diesel par-
ticulate fi lter could start a fire. ..,. •

Page 233 of 342

It takes a long time for the engine to warm up
fu lly when it is running at idle. However , wear
and nox ious em issions are especially high
when the engine is warming up. So you should drive away as soon as you start the engine and
avoid running at high rpms while the engine is
still warming up .
(D Note
Do not leave engine idling unattended af­
ter starting . If warning lights should come
on to indicate improper operation, they
wou ld go unheeded. Extended idling also
p roduces heat, which cou ld resu lt i n over­
heating or other damage to the vehicle or
other property.
Regular maintenance
A badly tuned engine unnecessarily wastes a lot of fuel.
"' Have your vehicle serv iced at regular inter-
vals.
By having your vehicle regularly serviced by an
author ized Audi dealer helps to ensure that it
r uns p roper ly and economically. The condition
of your vehicle not only affects its safety and
ab ility to hold its value, it also affects
fuel
c on sumpt ion .
Ch eck your oil each tim e yo u fill your tank .
The amount of oil used is related to engine
load and speed .
It is normal for the oil consumption of a new
engine to reach its lowest v alue after a certain
mileage has been dr iven .
You must drive your vehicle about 3,000 miles (S,000 ki lometers) before you can properly
assess o il consumption .
This a lso applies to fuel consumption and en­
gin e output.
0 Note
- Have yo ur vehicle maintained properly
and in accordance wit h the service rec­
ommendations in your War ranty
& Main-
Dri vin g and en vironm ent 231
tenance book let. Lack of proper mainte­
nance as well as improper use of the ve ­
hicle will impair the function of the
em ission contro l system and could lead
to damage.
- Do not alter or remove any component of the Emission Control System unless ap­proved by the manufacturer.
- Do not alter or remove any device, such as heat shie lds, switches, ign ition w ires,
valves, which are designed to protect
your vehicle's Emission Control System and other important vehicle compo­
nents.
Fewer short trips
Fuel consumption will always be relatively
high on short trips .
"' Try to avoid driv ing short distances w ith a
cold engine .
The eng ine and cataly tic converter have to
reach their opt imal
op erat ing temperature t o
reduce fuel consumpt ion and nox ious em is­
s ions effect ively .
Just after starting, a co ld eng ine in a mid-s iz e
car only achieves a fuel economy of 6-8 miles
per gallon (30 -40 l/l00km). After about a
half a mile , fuel economy cl imbs to 12 mpg
(20 l/100 km) . After about
2.5 miles (4 km),
the engine is at i ts p rope r opera ting tempe ra­
tu re and f uel economy has reached a normal
l evel. So you can see that yo u should avo id
short trips whenever possible.
T he
out sid e t emperat ure is also cr itica l in th is
regard. Your car consumes more fue l in the
winter than in the summer.

Page 234 of 342

232 Driving o ff road
Driving off road
Driving in difficult road
conditions and offroad
General information
The operation of the E lectronic Stability Con­
trol (ESC) is expanded for operation away
from paved roads. In situations where slip or a
d ifferential locking function is required, the
ESC offroad mode can be act ivated
c::;, page 219 . Hill descent control is also availa­
ble in the ESC offroad mode, which automati­
cally b rakes the vehicle and thereby keeps
speed constant when diffe rent wheel speeds
a re detected when descending a hill
c::;, page 220. Your Audi also has permanent
a ll-whee l drive in addition.
H oweve r, your Aud i is not a pure off road vehi­
cle .
It was no t built for d riving unde r extreme
conditions, e .g. fo r trips that are in the natu re
of an expedit ion .
Dri ve only on road s and offroad section s
which match the de sign of y our vehicl e and
y ou r abilitie s as a dri ver. Never take risks!
Before driving offroad
- Check the eng ine oil level, ti re p ressu re ,
coolant level , and the fluid level in the w ind­
shield washe r reservo ir.
- Stow luggage items and o ther objects in the
luggage compartment, and secure t hem
against s liding aro und .
After driving offroad
- After trips offroad, remove any twigs and
othe r foreign objects from the grill, the un­
derbody and the wheels. Pay spec ia l atten­
t ion to fo re ign objects (stones) which have
be come lodged in the tire tread.
- Clean t he body a nd the veh icle unders ide,
and in spec t the veh icle for poss ible damage.
- Clean dirty w indows , headlamp lenses , rear
l ights, and li cense plates .
- Perfo rm a brake check (part icularly after
t ravel ling th rough water) .
A WARNING
-Drive especially attentively and plan
a head in d iff icu lt road conditions and
when off road. Excessive speed o r inco r­
rect maneuvers can cause injuries and
damage to the vehicle.
-
- Always adapt your speed and driving
style to road, offroad, t raff ic, and weat h­
er cond itions. Drive e specially slowly off­
ro ad when you r view is res tricted.
- Please be awa re that in ESC off road
mo de, particularly on a smoo th and s lip­
pe ry road, the wheels may have an in­
crease d tendency to sp in and the vehicle
may b reak away - danger of skidding!
- Stabili ty is limited in the ESC off roa d
mode .
@) For the sake of the environment
Avoid damage to t he environmen t an d re­
s pect na tu re .
(D Tips
Only d rive w here it is permitte d and stay
on marked road s and pat hs.
Explanation of some technical terms
The following data refe r to ideal cond itions.
Depend ing on veh icle load and gro und condi ­
tions and the environment, the numbers may
vary. It is the driver's responsibility to decide
whether a vehicle can overcome a specific s it­
uat io n
c::;, ,&. .
Gradient angle
The number of meters in alt itude ga ined over
a distance of 109.4 yards or 100 meters
(grade) are given as a percentage or degrees.
Information about the gradient the vehicle
can climb under its own power (depends in
part on the road surface and engine power) .
Max imum pe rm itt ed grade : 3 1
°
Later al angle (slope of vehicle )
Indicates the angle up to which the vehicle
can be driven diagonally or across the fall line ..,.

Page 242 of 342

24 0 Cl eaning and protec tio n
Automatic car wash
The vehicle can be washed in almost any
modern automatic car wash .
The vehicle paint is so durable that the vehicle
can normally be washed without problems in
an automatic car wash. However, the effect on
the paint depends to a large extent on the de­
sign of the facility, the filte ring of the wash
water, the type of wash and care mater ial , etc.
I f the pa int has a dull appearance afte r going
through the car wash or is scratched, bring
this to the attention of the operator immedi­
ately. If necessary, use a different car wash.
Before going through a car wash, be sure to
take the usual precautions such as closing the
windows and the Panoramic sliding s unroof.
Factory installed antennas must not be re­
moved.
I f you have installed additional accessories on
the vehicle - such as spoilers, roof rack, etc. -
it is best to ask the car wash operator if these
should be removed.
A WARNING
Please take note of the following po ints
before going through an automatic car
wash with your vehicle, so that you can avoid damage to your vehicle .
- Compare the track of your vehicle with the distance between the gu ide rails of
the fac ility- there is a risk of damage to
the whee ls and t ires.
- Compare the height and w idth of your
vehicle with the height and width of the
t u nnel at the facility.
- Fold the exte rior mirrors flat - t here is a
risk of damag ing the exte rior m irrors.
Power folding exterior mirrors* mus t not
be folded in or out by hand. Use the pow­
er function!
- Do not al low the wiper blade to fall onto
the windshield after the vehicle is dried -
there is a r isk of damag ing the paint on
the hood .
- Always read and heed all WARNI NGS and
other information ¢
page 239.
Washing the vehicle by hand
A lot of water is needed when washing a vehi­
cle by hand .
.,. Before you start washing, make sure you
have read and understood the WARNINGS
¢ .&. in General information on page 239 .
.,. First soak all dried d irt unt il it is soft, then
r inse it off .
.,. As you clean you r vehicle , start w it h the
roof and work your way dow n to the bo ttom,
using a sponge, a sponge g love or a clean
brush.
.,. Rinse the sponge or the sponge glove often,
flushing it clean each time.
.,. Use spec ial car shampoo only for very per­
sistent d irt .
.,. Rinse the car thoroughly wit h water .
.,. Use a chamo is leather to gently w ipe the ex-
ter io r d ry.
Use a separate sponge for cleaning the
wheels, door s ills and other regions exposed
to road dirt . In this way, you will not scratch
the pa int with coarse pa rticles imbedded in
the sponge the next time you wash the car.
A WARNING ~ -
- Do not clean the underside of the chas­
sis, fenders, wheel covers , or other ha rd
to reach pa rts without protect ing your
hands and arms . You may cut yourself on
sharp-edged metal parts.
- Always read and heed a ll WARNINGS and
other information ¢
page 239.
(D Note
- Never try to remove dirt, mud or dust if
the surface of the ve hicle is dry . Never
use a dry cloth or sponge, s ince this
co uld scratch your vehicle's paint or win ­
dows .
- Never wash your car in bright s unlight.
Drops of water act as magn ifying lenses
and may damage your paint .
- When you wash your car in the winter: if you rinse your vehicle with a hose, be careful not to aim the stream of water

Page 244 of 342

242 Cleaning and protection
Polishing
Polish your vehicle on ly if the paint has lost its
shine and the g loss cannot be brought back
with wax.
I f the polish used does not contain preserva­
tive compounds, the paint must be waxed af­
terwards .
A WARNING
Always read and heed a ll WARNINGS and
other information
¢ page 239 .
~ Note
Do not use car wax on
- matte or anodized metal trim
- rubber or rubbe r-like tr im.
Trim strips
Metal trim needs special core .
For environmental reasons, Audi fabricates
the bright tr im strips and trim pieces from
pure chromium-free aluminum.
Dirt and marks on the trim strips should be
removed with a
pH-balanced cleaning agent
(do not use a chrome cleaner). Authorized Au­
d i dealers carry clean ing products wh ich have
been tested for use on your veh icle and are
not harmful to the environment .
To avoid corros ion on the exterior trim str ips,
only a pH-balanced solution should be used
for the w indshield washer .
A WARNING
Always read and heed all WARNINGS and
other information
¢ page 239.
Plastic and vinyl
Plastic needs special core.
Use a clean, damp cloth or sponge to remove
dust and light surface dirt. For other soil, use
a lukewarm all-purpose clean ing solution or a
mild saddle soap for vinyl trim. Remove water
spots and traces of soap w ith a clean, damp cloth
or sponge. Use a clean, soft cloth to rub
dry.
G rease , tar or oil sta ins can be removed with a
clean cloth or sponge soaked with all-purpose
cleaner or with a so lvent designed especially
to clean vinyl.
Occas ional ly apply a colorless vinyl or leather
preservative to re tain the materia l's luster
and pliability.
A WARNING
A lways read and heed all WARNINGS and
other information ~
page 239.
Aluminum trim
Use only neutral-pH products to remove spots
and deposits from a luminum surfaces.
Chrome care products and alkaline cleaners
will attack aluminum surfaces and can dam­ age them over time.
A WARNING
Always read and heed all WARNINGS and
other information
~page 239.
Touch-up paint
Minor point damages should be touched up
immediately.
"' Use e ither a touch-up paint stick or spray
pa int to cover m ino r scratches and nicks.
Your authorized Audi dealer has touch-up
paint for minor scratches and stone chips.
Scratches should be touched up soon after
they occur to prevent corrosion .
If a spot starts to rust, however, a simple
touch-up job will not be enough. The affected
surface must be sanded smooth and coated
with an anti-rust primer before the painted
finish can be restored.
The number for the original veh icle paint can
be found on the vehicle identification label
~page 314. ..,.

Page:   < prev 1-10 11-20 21-30 31-40 41-50 50 next >