warning AUDI TT 2013 Owner´s Manual

230 Fuses and bulbs
-No. Equipment
24 Transmission (control unit)
25 Heater rear
window Coupe/
heated rear window Roadster
26 Driver's side power window
27 Passenger's side power window
28 Not used
29 Washer pump
30 Cigarette lighter
31 Starter
32 Steering column module
33 Instrument cluster
34 Radio navigation system, radio
35 Audio amplifier
36 Engine (control unit)
37 CAN (Gateway)
38 Cigarette lighter
39 Not used
40
------------4 l Not used
42
43 Not used
44
45 Not used
46
47 SOARS tuner, cell phone pack-
age, TV tuner
48
49 Not used
Fuse location, left side of engine
compartment Amps
15
30/20
30
30
-15
20
40 5
5
20/15
30
10 5
20
-
-
5
5
Fig. 167 Illust ration of fuse holder on left side of en·
gine compartment: fuses (without fuse cover)
Some of the equipment items listed are op-
t ional or only available on certain model con-
figurations.
Note that the following table is accurate at
the time of going to press and is subject to
change.
No. Equipment Amps
Fuse holder (black)
1 Not used
-2 Not used
3 Not used
4 Not used
Anti-theft warning system (sen-
'
5 sor), anti-theft warning system 5
(horn)
6 Headlamp
washer system
30
Electric fuel pumps (supply),
7 volume control valve/Interrelais 15/10 (5-cyl.)
8 Windshield wipers
30
9 Heated seats (driver and pas-
25
senger)
10 Lumbar
support (driver and
10
passenger)
11 Not used
12 Ventilation blower 40
Fuse holder (brown)
1 Not used
2 Electric fuel pump (5-cyl.) 30
3 Not used
Relay coil relay volume control
5 valve (4-cyl.)/02 sensors (5- 5/10
7 cyl.)
02 sensors
Positioning valves pre-wired en­
gine harness
Ignition coils
9 Engine (control unit)
10 Water pump delayed-off 10
10
20
25 10 ..,_.

No. Equipment Amps
11 Feed (brake peda l) 5
-
12 Activated charcoal filter/charge I pressure control valve 10
Bulbs
Replacing light bulbs
For your safety, we recommend that you have
your authori zed Audi dealer replace burned
out bulbs for you .
It is becoming increasingly more and more
difficult to replace vehicle light bulbs since in
many cases, other parts of the car must first
be removed before you are able to get to the
bulb . Th is appl ies especially to the l ight bulbs
in the front of your car which you can only
reac h through the engine compartment.
Sheet metal and bulb holders can have sharp
edges that can cause ser ious cuts, and parts
must be correctly taken apart and then prop­
e rly put back together to help p revent break­
age of parts and long term damage from wa­
ter that can enter housings that have not been properly resealed.
F or your safety, we recommend that you have
your author ized Audi dealer replace any bu lbs
for you, since your dealer has the p roper tools,
the correct b ulbs and the expertise.
Ga s di sc harg e lamp s (Xeno n light s}*:
Due to the high electrical voltage, have the
bulbs replaced by a qualified technician.
Headlights with Xenon light can be identified
by the high voltage sticker.
A WARNING
Contact with high-voltage components of
t he electrical system and improper re­
placement of gas discharge (Xenon) head­
light bulbs can cause serious personal in­
jury and death .
- Xenon bulbs are pressurized and can ex­
plode when being changed.
Fu ses and bulb s 231
-Changing Xenon lamps requires the spe­
cial tra ining, instructions and equip­
ment.
- On ly an authorized Audi dealer or other
qualif ied workshop should change the
bulbs in gas discharge lamps .
A WARNING .,.;
There are parts with sharp edges on the
openings and on the bulb holders that can
cause serious c uts.
- If you are uncertain about what to do,
have the work performed by an a uthor­
ized Audi dealer or othe r qualified work­
shop. Ser ious personal in ju ry may result
from imprope rly performed work.
(D Tips
- If you must replace the light bulbs your­
self, a lways remember that the eng ine
c ompartment of any vehi cle is a hazard­
ous area to work in. A lways read and
heed all WARN INGS
~page 174, Engine
compartment ¢&, .
-It is best to ask your authorized Audi
dealer whenever yo u need to change a
bulb .
•
•
-

232 Emergency situations
Emergency situations
General
This chapter is intended for trained emer­
gency crews and working personnel who
have the necessary tools and equ ipment to
perform these ope rations.
Starting by pushing or
towing
Q;) Note
Vehicle s with an automati c transmission
cannot be started by pushing or towing .
Starting with jumper
cables
If necessary, the engine can be started by
connecting it to the battery of another vehi­
cle.
If the engine should fail to start because of a
discha rged or wea k batte ry, the battery can be
connected to the battery o f
another vehicle,
using a
pair of jumper cables to start the en­
g ine .
Jumper cables
Use only jumper cab les of sufficiently
large cross section to safely carry the starter
cur rent. Refer to the manufacturer's specifica­
ti ons.
Use on ly jumper cables which have
insulated
termina l clamps and are properly marked for
d istinction :
plus(+) cable in most cases colo red red
minu s(-) cable
in most cases colo red black .
_& WARNING
Batterie s contain elec trici ty, a cid, and ga s.
Any of th ese c an cause ve ry seri ous or f ata l
inju ry . Follow the instructions below fo r
safe han dling of your ve hicle's battery.
- Alw ays s hield yo ur eyes and avoid lean ­
ing over the batte ry w henever possib le . -
A discharged battery can a lready freeze
at temperatures just be low 32 °F (0 °C).
Before connect ing a jumper cab le, the
frozen battery must be thawed com­
p letely, othe rwise it cou ld explode .
- Do not allow batte ry acid to contact eyes
or skin . Fl ush any contacted a rea wi th
water immediat ely .
- Imp roper use of a booster battery to
s tart a vehicle may cause an explosion.
- Vehicle batter ies generate explosive gas­
es . Keep sparks, flame and lighted ciga­
rettes away from ba tte ries .
- Do not try to jump start a ny ve hicle w ith
a low ac id leve l in the battery .
- The vo ltage of the booster batte ry m ust
a lso have a 12-Vo lt rat ing . The capacity
(A h) of the booster batte ry should not b e
lowe r than that of the discharged bat­
tery . U se o f batt erie s of d iffe ren t voltage
or subs tanti ally diffe ren t "Ah" rat ing
may c ause an exp losion and person al in­
ju ry .
- N ever ch arge a fr ozen bat te ry. Gas t rap ­
ped in the ice may ca use an ex plosion .
- N ever ch arge o r use a batt ery th at has
been fro zen. T he battery case may have
be weakened.
- Us e of batt erie s of di ffere nt vo lta ge or
substan tially differen t ca pa city (Ah) rat ­
i ng may cause an exp losion and injury.
T he capac ity (Ah) of the booster battery
should not be lower than that of the dis­
charged batte ry.
- Before you check anything in the engine
compartment, always read and heed a ll
W ARNI NGS
c::;,page 174, Engine com­
partment .
@ Note
-App lying a hig her voltage booster ba t­
tery will cause expens ive damage to se n­
sitive electronic components, such as
cont ro l units , relays, rad io, etc.
- There must be no electrical contact be­
twee n the vehicles as otherwise current
cou ld already start to flow as soo n as th e
posi tive (+) term inals are connect ed. ""

234 Emergency sit uat ions
_& WARNING
To avo id serious per sonal injury and dam­
age to the vehicle, heed all warnings and
instructions of the jumper cable manufac­
turer. If in doubt, call for road serv ice.
- Jumper cables must be long enough so
that the vehicles do not touch.
- When connecting jumper cables, make
surethattheycannotgetca ughtinany
moving parts in the eng ine compart­
ment.
- Before you check anything in the engine
compartment, always read and heed all
WARNINGS
c::> page 174, Engine com­
partment.
(D Note
Improper hook-up of jumper cables can ru ­
in the generator.
- Always connect POSITIVE( +) to POSI­
TIVE(+), and NEGATIVE(-) to NEGATIVE ( - ) ground post of the battery manager
control unit.
- Check that all screw plugs on the battery
ce lls are screwed in firmly. If not, tighten
plugs prior to connecting clamp on nega­
tive battery terminal.
- Please note that the procedure for con­
nect ing a jumper cable as described
above applies spec ifically to the case of
you r vehicle be ing jump started. When
you are giving a jump star t to a nothe r ve­
hicle, do
not connect the negat ive (-) ca­
ble to the negat ive (-) term inal on the
discharged battery @. Instea d, secure ly
connect the negative (-) cable to either a
solid metal component that is firmly
bo lted to the engine block or to the en­
gine block itself. If the battery that is be­ i ng charged does not vent to the outside,
escap ing batte ry gas cou ld ign ite and ex­
plode!
-
Emergency towing
with commercial tow
truck
General hints
Your Audi requires special handling for tow­
ing.
T he following information is to be used by
commercial tow truck operators who know
how to operate their equipment safely.
- Ne ver tow your Audi , towing will cau se
damage to the engine and tr an smi ssion .
- Ne ver wrap th e safet y chain s or winch ca­
ble s ar ound the brak e lines.
- To prevent unne ces sary damage , your Audi
must be tran sp o rt ed with a car carrier
(flatbed truck ).
- To load th e vehi cle on t o the flat bed , u se
the t owing loop found in the vehicle tool s
and attach to the front o r rear anchorage
c::> page 235 and c::> page 236.
A WARNING
--A vehicle being towed is not safe for pas­
sengers. Never allow anyone to ride in a
vehicle be ing towed, for any reason.

Front towing loop (Version A)
Do not install the front towing loop until it is
needed.
Fig. 170 Front bumper : removing t he grill
Fi g. 171 Fron t bumper: screwing in the towing loop
The tow ing loop fits into the th readed hole lo­
cated on the r igh t side of the fron t bumper
behind the grill.
"' Remove the s cre wd river and tow ing loop
from the vehicle tool kit ¢
page 220.
"' Inse rt the screwdrive r into the s lot as
shown and press toward the center of the
vehicle
r!.> fig. 170 . At the same time, pull
the grill forward and out.
"' Screw the towing loop tightly into the
threaded hole as far as it will go¢
fig. 171 .
When it is no longer needed, unscrew the
towline eye and put it back into the on-board
toolkit. Make sure to have the towline eye
stored in the vehicle at all times.
When insta lling the grill for the air duct, be
sure that the tabs on the gr ill are first insert­
ed into their guides on the vehicle. Then push
the grill into position.
Emergenc y situ ation s 235
A WARNING
If the tow ing loop is not screwed in as far
as it will go, the thread can pull out when
the vehicle is towed -potent ia l risk of an
accide nt.
Front towing loop (Version B)
Do not install the front towing loop until it is
needed.
F ig . 17 2 Righ t fro nt sectio n: remov ing the air inta ke
g ri lle
Fig . 17 3 Righ t front section w it h plastic cover
A threaded opening w ith left-hand th reads is
located at the front right of the bumper be·
hind the air intake grille. The towing loop is
i nstalled in this opening .
"' Remove the screwdriver and the tow ing
loop from the vehicle too l kit¢
page 220.
"' Reach through the air intake grille, grip the
hor izonta l fins and pull it forward to re ·
move .
"' Use the screwdrive r to pry the plastic cover
off r!.>fig. 173.
"' Inst all th e tow ing loop in the threaded
open ing and tighten it unt il it stops
r!.> page 235, fig . 171 . ~

236 Emergency situations
Remove the towing loop when you are done
using it and place it back in the vehicle tool
kit. Always keep the towing loop in the vehi­
cle .
When installing the air intake grille, insert the
tabs on the grille in the mounts on the vehicle
f ir st . Then press the grille in to secure it.
A WARNING
If the towing loop is not tightened until it
stops when installing, the threads may be
pulled out when tow ing the vehicle and
that could cause an accident .
Rear towing loop
Do not install the rear towing loop until it is
needed.
Fig. 174 Right rear section
Fig. 175 Rear bum per: screw ing in the towing loop
On the r ight side under the rear bumper there
is a threaded hole for the towing loop. The
threaded hole is protected by a cover.
> Remove the towing loop from the veh icle
toolkit ~
page 220 .
> Press the righ t side of the cover inward
forcefully to remove it from the bumper.
~fig. 174.
> Screw the towing loop tightly into the
threaded hole as far as it will go.
When it is no longer needed, u nscrew the
towing loop and put it back into the vehicle
toolkit. Be sure to have the towing loop stored
in the vehicle at all times.
A WARNING
-
If the tow ing loop is not screwed in as far
as it will go, the thread can pull out when
the vehicle is towed - potent ial r isk of an
accident.
Loading the vehicle onto a flatbed truck
Fig. 176 Vehicle on flatbed truck
Front hook up
> Align the vehicle with the centerline of the
car carrier ramp .
> Attach the winch hook to the front towline
eye previously installed.
Rear hook up
> Align the vehicle with the centerline of the
car carrier ramp.
> Attach the w inch hook to the rear towline
eye previously installed.
(@ Tips
Check carefu lly to make sure the hook-up
is secure before moving the car up the flat­
bed truck ramp.

Lifting vehicle
lifting with workshop hoist and with
floor jack
The vehicle may only be lift ed at the lifting
poin ts illustra ted.
F ig. 177 Rear lift ing point (r ig ht side)
Fi g. 178 Front lift ing po int frig h t side)
• Rea d and h eed WARN ING c:::> A-
• Locate lifting points c:::> fi g. 177 c:::> fig. 178 .
• Adjust lift ing arms o f wor kshop hoist or
f loor jac k to match vehicle lifting points.
• Inse rt a r ubber pad between the floor jac k/
workshop hoist a nd the lifti ng points.
If you must lift your vehicle with a floor jack
to work underneath, be sure the vehicle is safely supported on stands intended for this
purpose.
Front lifting point
The lifting point is locate d on the f loor pan re­
info rcement about at the same level as the
jack mounting point
c:::> fig. 178. Do not lift
the vehicle at the vertical sill reinforcement .
Rear lifting point
The lifting poi nt is locate d on t he vertical rein­
forcement of the lower sill for t he on boa rd
jack
c:::> fig. 177.
Emergency situations 237
lifting with vehicle jack
Re fer to c:::> page 225 .
_&. WARNING
-To re duce t he risk of ser ious injury an d
ve hicl e damage.
- Alwa ys lift the veh icl e only at the spe­
c ial w orkshop hoist and floor jack lift
p oin ts ill ust rated
c:::> fig. 177 and
c:::> fig. 178 .
-Fa il u re to Lift th e ve hicl e at th ese
p o ints co uld cau se the ve hi cle to til t or
f all from a lift if th ere i s a cha nge in ve­
h icl e weigh t distr ibu tion and balan ce.
This mi ght h app en, fo r ex am ple, whe n
h eavy co mpon ent s such as the eng ine
b lock o r transmission are remove d.
- Wh en removin g hea vy componen ts li ke
these, anchor vehicle to h oist or ad d cor ­
respo nding wei ghts to ma intain t he ce n­
ter of gravity. Ot herwis e, th e ve hicle
might tilt or slip off the ho ist, caus ing
serio us pe rso nal i nju ry.
CI) Note
-Be aware of the following points before
lifting the vehicle:
- The vehicle should never be lifted or
jacked up from underneath the engine
oil pan, the transmission housing, the
front or rear axle or the body side
members. This could lead to seriou s
damage.
- To avoid damage to the underbody or
chassis frame, a rubber pad must be inserted between the floor jack and
the lift points.
- Before driving over a workshop hoist ,
check that the vehicle weight does not
exceed the permissible lifting capacity
of the hoist.
- Before driving over a workshop hoist ,
ensure that there is sufficient clear­
ance between the hoist and low parts
of the vehicle.
-

238 General information
General information Explanation of
technical data
Some of the technical data listed in this man ­
ual require further explanation.
The tecical data for your vehicle are listed in
the charts starting on ¢
page 240. This chap­
ter provides general information, notes and
restrictions which apply to these data .
Vehicle identification
The key data are given on the vehicle identifi­
cation number (VIN) plate and the vehicle da­
ta sticker.
Fig. 179 Veh icle Ide ntificat io n Number (VlN) plate: lo ­
cation on driver 's side das h panel
Fig. 180 Th e vehicle identi fication label -inside the
luggage co mpa rtmen t
The Vehicle Identification Number (VIN)
is located on the driver's side so that it is visi­
ble from the outside through the windshield -
seer:!> fig. 179. You can also display the Vehi­
cle Identification Number of your vehicle in
the Driver Information display¢
page 24 .
The vehicle identification label
is located in the luggage compartment in the
spare wheel wel l.
The label¢
fig. 180 shows the following vehi­
cle data :
(D Product ion control No .
@ Vehicle identification No.
® Type code number
@ Type designation/engine output in Kilo-
watts
® Engine and transmission code letter
@ Paint No./Interior
(f) Optional equipment No.'s
Vehicle data 2 to 7 are also found in your War­
ranty
& Maintenance booklet.
The safety compliance sticker
is your assurance that your new vehicle com­
plies with all applicable Federal Motor Vehicle
Safety Standards which were in effect at the
time the vehicle was manufactured . You can
find this sticker on the left door jamb.
It
shows the month and year of production and
the ve hicle ident ification number of your vehi ­
cle (perforation) as well as the Gross Vehicle
Weight Rating (GVWR) and the Gross Axle
Weight Rating (GAWR) .
The high voltage warning label
is located on the lock carr ier .
The spark ignition system complies with
the Canadian standard ICES-002.
Weights
Gross Vehicle Weight Rating
The Gross Vehicle Weight Rating (GVWR), and
the Gross Axle Weight Rating (GAWR) for
front and rear are listed on a sticker on the
left door jamb.
The Gross Vehicle Weight Rating includes the
weight of the basic vehicle plus full fuel tank,
oi l and coolant, plus maximum load, wh ich in­
cludes passenger weight (150 lbs/68 kg per
Ill>

designated seating position) and luggage
weight.
Gross Axle Weight Rating
The G ross Axle Weight Rating is the maximum
l oad that can be applied at each axle of the
veh icle ¢.&. .
Vehicle capacit y weight
The vehicle capac ity we ight (max. load) is list­
ed either on the dr iver's side B-pillar or inside
the fuel filler flap.
Roof weight
The max imum perm issible roof weight is 165
lb (7 5 k g). The roof weight is made up of the
weight of the roof rack system and the weight
of the object being transported
¢ page 61,
Loading the roof rack .
.&, WARNING
- T he actual Gross Axle Weight Rat ing at
the front and rear axles shou ld not ex­
ceed the permiss ible weights, and their
combination must not exceed the Gross
Vehicle Weight Rat ing.
- Exceeding permissib le weight ratings can
result in vehicle damage, accidents and
personal injury.
CD Note
- The vehicle capacity weight figures apply
when the load is distributed evenly in the
vehicle (passengers and luggage). When
transporting a heavy load in the luggage
compartment, carry the load as near to
the rear axle as possib le so that the veh i­
cle's handling is not impa ired.
- Do not exceed the maximum permissible
axle loads or the max imum gross vehicle
weight. Always remember that the vehi­
cle's handling will be affected by the ex­
tra load. Therefore, adjust you r speed ac ­
cord ingly.
- Always observe loca l regu lations.
-
G ene ral in formation 239
Dimensions
The specifications refer to the basic model.
Differences may occur depending on the mod­
el type and options ordered, for example, tire
sizes.
CD Note
When driving up steep ramps, on rough roads, over curbs, etc. it is important to re­
member that some parts of your vehicle,
such as spoilers or exhaust system compo­ nents, may be close to the ground . Be
careful not to damage them .
•
•

24 4 Con sum er Inf ormation
steadi ly reduced the scope of maintenance
and repairs which can be carried out by vehicle
owners.
Als o, sa fe ty a nd en vir onm ent al con­
cerns place very strict limits on the nature of
repairs and adjustments to engine and trans­
miss ion parts which an owner can perform .
Maintenance, adjustments and repa irs usua lly
require special tools, testing devices and oth­
er equipment available to specially trained
workshop personnel in order to assure proper pe rformance, reliab ility and safety of the vehi­
cle and its many systems.
Improper maintenance, adjustments and re­
pa irs can impair the operation and reliab ility
of your vehicle and even void your vehicle war­
ranty. Therefore, proof of servic ing in accord­
ance w ith the ma intenance schedule may be a
condition for upholding a poss ible warranty
claim made within the warranty period.
Above all, operational safety can be adversely
affected, c reating unnecessary risks for you
and your passengers.
If in doubt about any se rv icing, have it done
by your author ized Audi dealer or any other
p roperly equipped and qualified workshop.
We strong ly urge you to give yo ur autho rized
Audi dealer the opportunity to perfo rm all
schedu led maintenance and necessary repairs.
Your dea ler has the facilities, original parts
and trained specialists to keep your vehicle
running properly.
Performing limit ed m aint enance yours elf
The following pages describe a limited num­
ber of proced ures which can be performed on
your vehicle with ordinary too ls, shou ld the
need arise and trained personnel be unavaila­
ble. Before performing any of these proce­
dures, always thoroughly read all of the app li­
cable text and carefully follow the instruc­
tions given . Always rigorously obse rve the
WARNINGS p rovided.
Before you ch eck anything in th e eng ine
co mpartm ent , alway s re ad and h eed all
WA RNINGS
c::> .&. and c::> .&. in Working in the
engine compartment on page 180.
_& WARNING
- Serious personal injury may occur as a re­
sult of improperly performed mainte­
nance, adjustments or repa irs.
- Always be extremely careful when work­
ing on the vehicle. Always follow com­
monly accepted safety pract ices and gen­
eral common sense. Never r is k personal
inju ry.
- Do not attempt any of the maintenance,
checks or repairs descr ibed on the fol­
lowing pages if you are not fu lly fam iliar
with these or other procedures with re ­
spect to the vehicle, or are uncertain how
to proceed .
- Do not do any work without the proper
too ls and equipment. Have the necessa ry
work done by your authorized A udi deal­
er or another proper ly equipped and
qualified workshop.
- The engine compartment of any motor
veh icle is a potentially hazardous area.
Never reach into the area around or
touch the radiator fan. It is temperature controlled and can sw itch on suddenly -
even when the engine is off and the igni­
tion key has been removed. The rad iator
fan switches on automatical ly when the
coo lant reaches a certain temperature
and will continue to run until the coo lant
temperature drops .
- Always remove the ign ition key before
anyone gets under the vehicle.
- Always support your vehicle with safety
stands if it is necessary to work under­
neath the vehicle. The jack supplied with
the vehicle is not adequate for this pur­
pose and cou ld collapse causing serious
personal injury.
- If you must work underneath the vehicle
with the wheels on the ground, always
make sure the vehicle is on leve l ground,
that the wheels a re a lways secure ly
b locked and that the engine cannot be
started.
- Always make sure the transmission se­
lector lever (automatic transmission) is