air bleeding CHEVROLET CAMARO 1967 1.G Chassis Workshop Manual

BRAKES

SECTION 5

CONTENTS OF THIS SECTION

Duo Servo Brakes

Disc Brakes
Page

5-1 Power Brakes

5-24 Special Tools
Page

5-31

5-32

DUO-SERVO BRAKES

INDEX

Page

General Description 5-1

Maintenance and Adjustments 5-3

Hydraulic Brake Fluid .. . 5-3

Bleeding Hydraulic System 5-3

Pressure Bleeding 5-3

Manual Bleeding 5_4

Push Rod to Main Cylinder Clearance 5-5

Hydraulic Brake Lines 5-5

Hydraulic Brake Hose 5-5

Hydraulic Brake Tubing 5-6

Brake Adjustment. .................... 5-7

Service Brake 5-7

Parking Brake 5-8

Component Replacement and Repairs 5-9

Parking Brake - Chevrolet, Chevelle and

Camaro 5^9

Pedal Assembly 5-9

Front Cable ,. . . 5-9

Center Cable 5-9

Rear Cables. . 5-9
Parking Brake - Chevy n 5-9

Lever Assembly 5-9

Idler Lever 5-11

Front Cable 5-11

Rear Cable . . ; 5-12

Parking Brake - Corvette 5-13

Lever Assembly . . . . 5-13

Front Cable 5-14

Rear Cable . . 5-14

Brake Pedal 5-15

Shoes and Linings 5-16

Organic 5-16

Metallic 5-17

Main Cylinder 5-18

Wheel Cylinders 5-21

Anchor Pin 5-22

Front Wheel 5-22

Rear Wheel 5-22

Brake Drums • 5-22

Brake Pipe Distribution and Switch Assembly . . . . . 5-23

Camaro Pressure Regulator Valve 5-23

GENERAL DESCRIPTION

All 1967 models are equipped with a new split brake

system as a safety feature. If a wheel cylinder or brake

line should fail at either the front end or rear end of

the vehicle, the operator can still bring the vehicle to

a controlled stop. The system is designed with separate

hydraulic systems for the front and rear brake using

a dual master cylinder (fig. 1). The design of the master

cylinder is similar to that used on the 1966 Corvette

in that it has two entirely separate reservoirs and outlets

in a common body casting. The front reservoir and outlet

is connected to the front wheel brakes, and the rear

reservoir and outlet is connected to the rear wheel

brakes. Two pistons within the master cylinder receive

mechanical pressure from the brake pedal push rod and

transmit it through the brake lines as hydraulic pressure

to the wheel cylinders. The filler cap is accessible from

inside the engine compartment.

A new brake pipe distribution and switch assembly

is mounted below the main cylinder. The front and rear

hydraulic brake lines are routed from the main cylinder,

through the brake pipe distribution and switch assembly,

to the front and rear brakes as shown in Figure 2. The

switch is wired electrically to the brake alarm indicator

light on the instrument panel. In the event of fluid loss

in either the front or rear brake system the indicator

on the instrument panel will illuminate red. (The indi-
cator will also' be illuminated when the parking brake is

applied.)

On Camaro models equipped with air conditioning, the

rear brake hydraulic line is routed through a pressure

regulator valve mounted on the left frame side rail

(fig. 3). The valve controls the hydraulic pressure to

the rear brakes resulting in the correct pressure balance

between the front and rear hydraulic systems.

The self-adjusting brakes (fig. 4), used on both front

and rear of all models, are the Duo-Servo single anchor

type which utilize the momentum of the vehicle to assist

in the brake application. The self-energizing or
self-

actuating force is applied to both brake shoes at each

wheel in both forward and reverse motion. The brake

shoe linings are bonded to the shoes.

Wheel cylinders are the double piston type permitting

even distribution of pressure to each brake shoe. To

keep out dust and moisture, both ejads of each wheel

cylinder are sealed with a rubber booC The wheel

cylinders have no adjustments.

The Chevrolet, Chevelle, and Camaro parking brakes

have a foot operated ratchet type pedal mounted to the

left of the steering column. A cable assembly connects

the pedal to an intermediate cable by means of an equal-

izer, where the adjustment for the parking brake is

incorporated. The intermediate cable attaches to the

CHEVROLET CHASSIS SERVICE MANUAL

BRAKES
5-3

PRIMARY

SHOE

PAWL
WIRE LINK

OVERRIDE

LEVER

VERRIDE

SPRING

RETURN

SPRING

STAR
WHEEL

Fig.
3—Camaro
Pressure
Regulator
Valve
Fig.
4-Self-Adjusting
Brake

MAINTENANCE AND ADJUSTMENTS

In any service operation it is extremely important

that absolute cleanliness be observed. Any foreign matter

in the hydraulic system will tend to clog the lines, ruin

the rubber cups of the main and wheel cylinders and

cause inefficient operation or even failure of the braking

system. Dirt or grease on a brake lining may cause

that brake to grab first on brake application and fade

out on heavy brake application.

The split system consists basically of two separate

brake systems. When a failure is encountered on either,

the other is adequate to stop the vehicle. If one system

is not functioning, it is normal for the brake pedal lash

and pedal effort to substantially increase. This occurs

because of the design of the master cylinder which

incorporates ah actuating piston for each system. When

the rear system loses fluid and takes in air, its piston

will bottom against the front piston. When the front

system loses fluid and takes in air, its piston will

bottom on the end of the main cylinders body. The loss

of fluid in one of the systems causes an uneven hydraulic

pressure balance between the front and rear systems.

The brake pipe distribution and switch assembly, near

the main cylinder, detects the loss of pressure and il-

luminates the brake alarm indicator light on the instru-

ment panel. The pressure loss is felt at the brake pedal

by an apparent lack of brakes for most of the brake

travel and then, when failed chamber is bottomed, the

pedal will harden.

HYDRAULIC BRAKE FLUID

Use GM Hydraulic Brake Fluid, Supreme No. 11 or

equivalent when servicing brakes. This brake fluid is

satisfactory for any climate and has all the qualities

necessary for proper operation, such as a high boiling

point to prevent vapor lock and the ability to remain

fluid at low temperatures.
In the event that improper fluid has entered the system,

it will be necessary to service the system as follows:

1.
Drain the entire system.

2.
Thoroughly flush the system with clean alcohol,

188
proof,
or a hydraulic system cleaning fluid

such as "Declene".

3.
Replace all rubber parts of the system, including

brake hoses.

4.
Refill the system.

5. Bleed the system.

BLEEDING HYDRAULIC SYSTEM

The hydraulic brake system must be bled whenever

any line has been disconnected or air has in some way

entered the system. A ''spongy" pedal feeling when the

brakes are applied may indicate presence of air in the

system. The system must be absolutely free of air at

all times. Bleeding should be done on the longest line

first; the proper sequence to follow is left rear, right

rear, right front, and left front (fig. 5). Bleeding of

brake system may be performed by one of two methods—

either pressure or manual.

PRESSURE
BLEEDING

1.
Clean all dirt from top of main cylinder and remove

cylinder cover and rubber diaphragm.

2.
Reduce fluid level in main cylinder until reservoirs

are approximately half full.

NOTE:
Make sure brake fluid in bleeder equip-

ment is at operating level and that the. equipment

is capable of exerting 30 to 50 lbs. hydraulic

pressure on the brake system.

3.
Install brake bleeder adapter J-22489 (fig. 6) on

main cylinder. Connect hose from bleeder equipment

to bleeder adapter and open release valve on bleeder

equipment.

CHEVROLET CHASSIS SERVICE MANUAL

BRAKES 5-4

RF

3

^ FRONT OF

~ VEHICLE

LF

4
RR

CZZZIZ3

2

LR

1

Fig.
5—Correct Bleeding Sequence

4.
Install brake bleeder wrench, Tool J-21472 on bleed-

er valve at wheel cylinder and install one end of

bleeder hose on bleeder valve (fig. 7).

5.
Pour a sufficient amount of brake fluid into a trans-

parent container to insure that end of bleeder hose

will remain submerged during bleeding. Place the

loose end of bleeder hose into the container. Be

sure the hose end is submerged in the fluid.

6. Open wheel cylinder bleeder valve by turning Tool

J-21472 counterclockwise approximately 1/3 of a

turn and observe flow of fluid at end of bleeder

hose.

7.
Close bleeder valve tightly as soon as bubbles stop

and brake fluid flows in a solid stream from the

bleeder hose.

8. Remove brake bleeder wrench and bleeder hose

from wheel cylinder bleeder valve.

9. Repeat Steps 4 through 8 on the remaining wheel

Cylinders in the correct bleeding sequence (fig. 5).

10.
Disconnect bleeder equipment from brake bleeder

adapter cover J-22489.

NOJE: The main cylinder on certain passenger

car models is tilted upward. When removing

the bleeder adapter on these models, place a

clean dry cloth behind and below the cylinder

to absorb any fluid spillage as the cover is

removed. v
Fig.
7—Bleeding Brakes Using Brake Bleeder

Wrench Tool J-21472

11.
adapter J-22489. Wipe all area

fluid was spilled during adapter

Fig.
6—Brake Bleeder Adapter Tool J-22489—Installed
Remove bleeder

dry of fluid if

removal.

12.
Fill master cylinder reservoirs to within 1/4" of

reservoir rims as shown in Figure 8.

13.
Install main cylinder diaphragm and cover.

MANUAL BLEEDING

1.
Clean all dirt from top of main cylinder and remove

cylinder cover and rubber diaphragm.

2.
Fill main cylinder reservoirs.

3.
Install brake bleeder wrench, Tool J-21472 on bleed-

er valve at wheel cylinder and install one end of

bleeder hose on bleeder valve (fig. 7).

4.
Pour a sufficient amount of brake fluid into a trans-

parent container to insure that end of bleeder hose

will remain submerged during bleeding. Place the

loose end of bleeder hose into the container. Be

sure the hose end is submerged in the fluid.

NOTE: Carefully monitor fluid level at main

cylinder during manual bleeding operations. Do

not bleed enough fluid at one time to drain the

reservoir completely. Replenish the reservoirs

with fluid while bleeding to insure a sufficient

amount of fluid is in the main cylinder at all

times.
To insure that outside air is not sucked

back into the hydraulic system, the bleeder

valve should be closed before the brake pedal

reaches the floor.

5.
Open wheel cylinder bleeder valve by turning Tool

J-21472 counterclockwise approximately 1/3 of a

turn. Slowly depress brake pedal. Just before brake

pedal reaches the end of its travel, close bleeder

valve and allow brake pedal to return slowly to the

fully released position. Repeat this procedure until

CHEVROLET CHASSIS SERVICE MANUAL

BRAKES
5-24

DISC BRAKES

INDEX

Page

General Description
. 5-24

Maintenance
and
Adjustments
5-24

Bleeding Hydraulic System
5-24

Parking Brake Adjustment
-
Corvette
5-24

Component Replacement
and
Repairs
5-25
Page

Brake Shoes
. . . . . 5-25

Brake Caliper
5-26

Brake Disc
5-29

Main Cylinder.
5-30

Parking Brake Shoes
-
Corvette
5-30

GENERAL DESCRIPTION

Four wheel disc brakes
are
standard equipment
on

the
1967
Corvette,
as in 1966. The
Corvette
may
also

be equipped with heavy duty disc brakes which include

new front calipers, shoes, linings,
and
rear pressure

regulator valve. This heavy duty option
is
used
in

conjunction with
a
vacuum power unit. Front wheel disc

brakes
are
installed
as
optional equipment
on
Chevrolet,

Chevelle, Camaro,
and
Chevy
II
models.

The disc brake,
(fig. 35),
consists
of a
fixed caliper,

rotating disc, splash shield,
and
mounting bracket.
The

caliper assembly contains four pistons and two shoe
and

lining assemblies with
the
lining riveted
to the
steel

shoes.
A
seal
and
dust boot
are
installed
on
each piston,

with
a
piston spring
in the
caliper cylinder bore beneath

each piston.
A
retaining pin extends through each caliper

half
and
both shoes
to
hold
the
shoes and linings
in
posi-

tion
in the
caliper.
On
Corvette heavy duty disc brakes,

two retaining cotter pins
are
used
at
each end
of the

caliper
to
secure
the
shoes
and
linings. Machined
sur-

faces within
the
caliper prevent
the
shoe
and
lining
assembly from rotating with
the
brake disc when pres-

sure
is
applied.

The disc, which
has a
series
of air
vent louvers
to

provide cooling,
is
mounted
on the
front wheel-hub.

The caliper straddles
the
disc and mounts
on a
mounting

bracket attached
to the
steering knuckle with
two
bolts.

The Corvette heavy duty option includes
a
pressure

regulator valve mounted
in the
rear brake line just

below
the
main cylinder. Chevrolet, Chevelle, Camaro,

and Chevy
n
models with disc brakes have
a
pressure

regulator valve mounted
in the
front brake line just

below
the
main cylinder. The valve controls
the
hydraulic

pressure
to the
front
or
rear brakes,
as
applicable,

resulting,
in the
correct pressure balance between
the

front
and
rear hydraulic systems. This valve guards

against premature .lock-up
of
front
or
rear wheels when

brakes
are
applied.

Maintenance, adjustment,
and
service operations which

are
not
included
in
this section
are the
same
as for

the Duo-Servo type brakes.

MAINTENANCE
AND
ADJUSTMENTS

BLEEDING HYDRAULIC SYSTEM

The operation
of
bleeding
the
disc brake hydraulic

system
is the
same
as for
Duo-Servo system outlined

in
the
front
of
this section. Note
the
exceptions below

and refer
to
bleeding procedures under Duo-Servo

brakes.

1.
When pressure bleeding equipment
is
used,
the

correct pressure setting
for
bleeding disc brakes

is 10-2.0
lbs. on
Corvette,
and 40 lbs. on all
other

models.

2.
The
front calipers contain
one
bleeder valve.
The

rear calipers
on
Corvette contain two bleeder valves

(one inboard
and one
outboard) which necessitates

the removal
of the
rear wheels
for
bleeding.

3.
Tapping
the
caliper with
a
rawhide mallet
as the

fluid
is
flowing
out may
assist
in
obtaining
a
good

bleeding
job.

4.
On
Chevrolet, Chevelle, Camaro
and
Chevy
II, the

spring loaded
end of the
pressure regulator valve

(fig.
36)
must
be
held (valve
in
open position) while

bleeding. This
is
done
by
depressing
and
holding

in
the
plunger
in the
end
of
the valve either
by
hand,

by taping,
or by
clamping.
PARKING BRAKE-CORVETTE

Adjustment

1.
Raise rear
end of
vehicle
and
place
on
jack stands.

2.
Remove rear wheels.

3/
Loosen brake cables
at the
equalizer until
the
park-

ing brake levers move freely
to the "off"
position

with slack
in the
cables.

4.
Turn
the
disc until
the
adjusting screw can
be
seen

through
the
hole
in the
disc.

5. Insert
an
adjusting tool
or
screw driver through
the

hole
in the
disc
and
tighten
the
adjusting screw
by

moving your hand away from
the
floor
on
both
the

left and right sides
(fig. 37).

6. Tighten until
the
disc will
not
move, then back
off

ten
(10)
notches.

7. Apply
the
parking brake four
(4)
notches from inside

the
car.

8. Tighten
the
brake cables
at the
equalizer
to
produce

a light drag with
the
wheels mounted.

9. Fully release
the
parking brake handle
and
rotate

the rear wheels.
No
drag should be evident with
the

handle released.

CHEVROLET CHASSIS SERVICE MANUAL

BRAKES
5-31

POWER BRAKES

INDEX

General Description 5-31

Maintenance
and"
Adjustments 5-31

Inspection . ... 5_31

Lubrication 5-31

Bleeding Instructions . . . 5.31

Air Cleaner Service . . . , 5.31
Page

Component Replacement 5-31

Power Brake Cylinder ......* 5-31

Removal . . 5-31

Disassembly and Assembly See Overhaul Manual

Installation . . . . 5-31

GENERAL DESCRIPTION

The Power Brake Unit is a self-contained hydraulic

and vacuum unit, utilizing manifold vacuum and atmos-

phere pressure for its power.

This unit permits the use of a low brake pedal as well

as less pedal effort than is required with the conventional

(nonpower) hydraulic brake system. Only two external
line connections are necessary -
one
a vacuum connection

from manifold to check valve located on front shell; the

other, a hydraulic connection from the main cylinder

outlet directly into the hydraulic system. The unit is

mounted on the engine side of the fire wall and directly

connected to the brake pedal.

MAINTENANCE AND ADJUSTMENTS

INSPECTIONS

1.
Check vacuum line and vacuum line connections as

well as vacuum check valve in front shell of power

unit for possible vacuum loss.

2.
Inspect all hydraulic lines and connections at the

wheel cylinders and main cylinder for possible

hydraulic leaks.

3.
Check brake assemblies for scored drums, grease

or brake fluid on linings, worn or glazed linings,

and make necessary adjustments.

4.
Check brake fluid level in the hydraulic reser-

voirs.
The reservoirs should be filled to the levels

shown in Figure 8.

5. Check for loose mounting bolts at main cylinder and

at power section.

6. Check air cleaner filter in power piston extension

and replace filter if necessary.

7. Check brake pedal for binding and misalignment

between pedal
-and
push rod.

LUBRICATION

The power brake unit is lubricated at assembly and
needs no further lubrication other than maintaining

normal reservoir fluid level. The reservoir should be

filled as described in this section.

BLEEDING INSTRUCTIONS

The power system may be bled manually or with a

pressure bleeder as outlined in this section. Use only

GM
Supreme 11 Brake Fluid or equivalent. Do not use the

power assist while bleeding. The engine should not be

running and the vacuum reserve should be reduced to

zero by applying the brake several times before starting

the bleeding procedure.

AIR CLEANER SERVICE

Servicing of the air cleaner is recommended and the

element replaced when restriction becomes severe

enough to affect power brake response. At any other

time, if cleaning of the filter is felt necessary, it should

be shaken free of dirt or washed in soap and water and

thoroughly dried.

COMPONENT REPLACEMENT

POWER BRAKE CYLINDER

Removal

1.
Remove vacuum hose from vacuum check valve.

2.
Disconnect hydraulic lines at main cylinder.

Disconnect push rod at brake pedal assembly.

Remove nuts and lock washers securing power unit

to fire wall, and remove power unit from engine

compartment.
3.

4.

NOTE:
Chevy

to fire wall.
has a three stud attachment

Repair procedures for the power cylinder are outlined

in the Brake Section of the Overhaul Manual-for service
of the main cylinder refer to applicable portion of

"Standard Brakes" in this manual.

Installation

1.
Mount the power brake assembly in place and install

the attaching nuts and lock washers.

2.
Attach vacuum line to check valve.

3.
Secure hydraulic lines to main cylinder.

4.
Attach push rod to brake pedal assembly, and check

operation of stop light.

5. Bleed brakes as outlined in this section.

CAUTION: After replacing the unit on the vehi-

cle,
start the engine and allow vacuum to build

up before applying the brake.

CHEVROLET CHASSIS SERVICE

STEERING
9-33

POWER STEERING

INDEX

Page

General Description
. 9-33

Maintenance
and
Adjustments
9-33

Bleeding Hydraulic System
9-33

Fluid Level
. 9-33

Adjustments
. 9-34

Power Steering Gear
. . 9-34

Pump Belt Tension
9-34
Hydraulic System Checks
9-34

Component Replacement
and
Repairs
. 9-35

Power Steering Pump.
. 9-35

Power Steering Gear
9-36

Control Valve
and
Adapter Assembly
9.35

Power Cylinder
9.37

Power Steering Hoses
9.39

GENERAL DESCRIPTION

Two types
of
power steering
are
used
for 1967.
One
is

the conventional linkage type
for
Chevy
n and
Corvette

vehicles
and the
other
is the
integral gear type
for

Chevrolet, Chevelle,
and
Camaro.
For
both types
the

hydraulic pressure
is
provided
by an
engine-driven vane-

type pump.

On
the
Chevy
n and
Corvette linkage type power steer-

ing, hydraulic pressure
is
delivered through
a
hose from

the pump
to a
valve which senses
the
requirement
for

power assistance
and
supplies
the
power cylinder
ac-

cordingly.
The
steering gear used with this power steer-

ing
is the
same basic unit used
on
manually steered

vehicles;
it is
serviced
as
outlined
in the
manual steering

part
of
this section except
for
adjustment, which
is

covered
in the
following pages.
The
steering linkage also

is serviced the same
as
manual counterparts.

The Chevrolet, Chevelle
and
Camaro integral gear type

power steering
has the
hydraulic pressure delivered

from
the
pump through two hoses
to the
steering gear.
In
the power steering gear
the
steering shaft, hydraulic

valve, worm, and rack-piston
nut are all in
line making
a

compact
and
space saving assembly.
All oil
passages
are

internal within
the
gear except
the
pressure
and
return

hoses.

The steering gear
is a
recirculating ball system
in

which steel balls
act as a
rolling thread between
the

steering worm
and
rack-piston
nut. The
rack-piston
nut

is
all one
piece
and is
geared
to the
sector
of
the piston

shaft.
The
valve
is
contained
in the
gear housing elimi-

nating
the
need
of
bolts
or
seals
to
attach
a
separate

valve housing.

The valve
is an
open-center, rotary-type three
way

valve.
The
spool
is
held
in
neutral position by means
of a

torsion
bar. The
spool
is
attached
by
means
of
the stub

shaft
to one end of the
torsion
bar
and
to the
valve body

on
the
other
end.
Twisting
of the
torsion bar allows
the

spool
to
move
in
relation
to the
valve body thereby oper-

ating
the
valve.

MAINTENANCE
AND
ADJUSTMENTS

BLEEDING HYDRAULIC SYSTEM

1.
Fill
oil
reservoir
to
proper level and
let oil
remain

undistrubed
for at
least two minutes.

2.
Start engine
and run
only
for
about
two
seconds.

3.
Add
oil if
necessary.

4.
Repeat above procedure until
oil
level remains
con-

stant after running engine.

5. Raise front
end of
vehicle
so
that wheels
are off
the

ground.

6. Increase engine speed
to
approximately
1500 rpm.

7. Turn
the
wheels
(off
ground) right
and
left, lightly

contacting
the
wheel stops.

8. Add
oil if
necessary.

9. Lower
the car and
turn wheels right and left
on the

ground.

10.
Check
oil
level and refill
as
required.

11.
If oil is
extremely foamy, allow vehicle
to
stand
a

few minutes with engine
off and
repeat above

procedure.
,

a.
Check belt tightness
and
check
for a
bent
or
loose

pulley. (Pulley should
not
wobble with engine

running.)
b.
Check
to
make sure hoses
are not
touching
any

other parts
of the car,
particularly sheet metal.

c. Check
oil
level, filling
to
proper level
if
neces-

sary, following operations
1
through
10.
This

step
and
Step
"D" are
extremely important
as

low
oil
level and/or
air in the oil are the
most

frequent causes
of
objectionable pump noise.

d. Check
the
presence
of air in the oil. If air is

present, attempt
to
bleed system
as
described
in

operations
1
through
10. If it
becomes obvious

that
the
pump will
not
bleed after
a few
trials,

proceed
as
outlined under Hydraulic System

Checks.

FLUID
LEVEL

1.
Check
oil
level
in the
reservoir
by
checking
the dip

stick when
oil is at
operating temperature.
On

Chevelle models equipped with remote reservoir,

the reservoir should
be
maintained approximately

3/4 full when
oil is at
operating temperature.

2.
Fill,
if
necessary,
to
proper level with
GM
Power

Steering Fluid
or, if
this
is not
available, automatic

CHEVROLET CHASSIS SERVICE MANUAL

ACCESSORIES
15-6

port thereby supplying vacuum to the Servo unit.

During system operation
the
following events occur:

1.
Car
speed below
20
mph—no function
of the
unit

because
the
rubber drum
has
not rotated
far
enough

to close
the
solenoid points.
No
energizing current

can flow through the solenoid coil.

2.
Car
speed above
20
mph—The tang
on the
rubber

drum
has
closed
the
solenoid points
and
current
is

flowing through
the 40 ohm
resistance wire
to the

solenoid coil. This current
is
not sufficient to "pull

in", the solenoid.

3.
Driver partially presses Engagement Switch—full

voltage flows through
the
solenoid
to
pull
it
into

operation. Solenoid
cam
tension
on the "U"
clip
is

released and the clip grips the rubber drum. Simul-

taneously the vacuum switch operates; applying man-

ifold vacuum
to the
Servo unit which tightens
the

throttle chain. When
the
driver releases pressure

from
the
accelerator pedal
the
unit will position the

throttle
to
maintain the speed
at
the time
of
solenoid
operation.

Driver releases
the
Engagement Switch—current

flows
to the
solenoid through
the 40
ohm wire and

since the solenoid is "pulled in", the reduced current

flow
is
sufficient to hold
it
in position.

The
car
begins
to
ascend
a
hill—car speed drops

slightly (very slightly) and the magnetic force on the

driven disk
of the
speed sensor
is
decreased.
The

disk rotates slightly
(as
would
a
speedometer shaft

because
of
hairspring tension) turning
the
rubber

drum. Since
the "U"
clip
is
gripping
the
drum,
it

moves
the
slide which COVERS
the air
bleed ports

more. With less air bleeding into the Servo, greater

vacuum exists
in it
and the diaphragm moves toward

the vacuum port opening
the
throttle wider.
The

tapered needle moves into the orifice further and the

diaphragm balances
in a
new position with the wider

throttle opening.
Car
speed
has
been maintained

automatically.

1.
Speedometer Cable

Adapter (From

Transmission)

2.
Gasket

3. Speedometer Cable

Adapter
(To

Speedometer)

4.
Adapter
and
Magnet

Housing

5. Rotating Magnet

6. Helical Ramp
7. Field Plate Adjusting

Pinion

8. Adjusting Pinion

Locating Spring

9. Brass Magnetically

Driven Disk

10.
Field Plate

11.
Hair Spring

12.
Hair Spring Keeper

13.
Rubber Drum

Tang
14.
Rubber Drum

1$.
"U"
Shaped Clutch

Spring

16.
Air
Bleed Sleeve

17.
Orifice Tube

18.
Orifice

19.
Orifice Tube Locknut

20.
Clutch
and
Solenoid

Housing

21.
Vacuum Supply Port

(To Servo)
22.
Vacuum Port (To

Intake Manifold)

23.
Vacuum Valve Slide

24.
Solenoid Coil

25.
Solenoid Plunger

Return Spring

26.
Solenoid Cover Gasket

27.
Air Filter

28.
Solenoid Cover

29.
Air Inlets

Fig.
9-
Regulator
-
Exploded

CHEVROLET CHASSIS SERVICE MANUAL

ACCESSORIES 15-7

6. The car begins to descend a hill--car speed in-

creases slightly and the regulator movements oc-

curing above occur again except in reverse. The

rubber drum is turned further against spring tension

and the air bleed orifices are uncovered more. This

bleeds more air to the Servo reducing the vacuum in

the unit. The diaphragm moves away from the

vacuum port, closes the throttle slightly, and with-

draws the tapered needle from the vacuum orifice.

With the orifice enlarged, the increased vacuum

counteracts the increased air bleed and the dia-

phragm finds a balance again at a reduced throttle

opening.

7.
Driver accelerates by pressing accelerator pedal-

car speed increases and the system responds by

moving the diaphragm to decrease throttle opening.

Since a bead chain is used, the chain merely relaxes

and has no effect on throttle operation. After the

driver releases pressure from the pedal, the throttle

will close until car speed decreases to the pre-set

speed. At that point the Regulator bleeds less air

to the Servo which opens the throttle enough to

maintain the pre-set speed. The system returns to a

stable condition.

8. Driver desires higher controlled speed, presses ac-

celerator until new speed is reached, and depresses

Engagement Switch fully and releases button--speed

sensing assembly tries to turn in a direction that

would decrease the throttle opening until the driver

fully depresses the Engagement Switch. Then the

current is cut off to the solenoid which retracts; the

solenoid nose expands the "U" clip releasing its

grip on the rubber drum. The drum and disk as-

sembly then rotates to a new position because of the

higher car speed. When the solenoid retracts, it also

shuts off vacuum to the Servo and opens the vacuum

port to atmospheric pressure within the Regulator

thereby bleeding down the Servo toward idle throttle

position. As the driver releases the Engagement

Switch, the contacts cause "pull in" and "hold in" of

the solenoid respectively. The system is engaged to
maintain the car speed at the time of Engagement

Switch release.

9. Driver desires lower cruising speed, presses En-

gagement Switch fully, waits until car speed de-

creases to desired speed then releases Switch--when

the Engagement switch is fully depressed the sole-

noid is de-energized causing the vacuum switch to

bleed down the Servo to idle throttle position and the

"U"
clip of the idle bleed valve is released from the

rubber drum. The drum and disk assembly is free

to rotate to a position which corresponds to vehicle

speed as the car slows. When the driver releases

the Engagement Switch, the unit "pulls in" and "holds

in" in the normal manner. The air bleed valve is

clutched to, the rubber drum at the car speed during

switch release. Vacuum is again applied to the

Servo and throttle control is assumed by the Regu-

lator to maintain the car speed at the time of switch

release.

10.
With system in operation, driver applies brakes--

simultaneously the Vacuum Release and Electric

Release Switches operate. The Vacuum Switch

bleeds air into the Servo through the air bleed line

coming from the Regulator. The vacuum is reduced

in the Servo and the throttle returns to idle position.

The Electric Release Switch cuts off power to the

entire system and the solenoid is de-energized. If

the driver removes his foot from the brake pedal the

Electric Switch again feeds voltage to the Engage-

ment Switch and the Vacuum Switch seals the air

bleed line. If the vehicle speed is above 20 mph

when this occurs, reduced voltage will flow to the

solenoid through the 40 ohm wire which will not be

sufficient to "pull in" the unit. If vehicle speed is

below 20 mph no current will flow since the tang

on the rubber drum has opened the low limit switch

points in the Regulator. In either case, after de-

pressing the brake pedal, the system will not con-

trol car speed until the driver operates the engage-

ment switch above 20 mph.

SERVICE OPERATIONS

The components of the Cruise Master system are de-

signed to be replaced should they become inoperative.

The Regulator is calibrated in such a manner during

manufacturing that overhaul operations are impractical.

However, one adjustment may be made to the Regulator to

correct speed drop or increase at the time of

engagement.

BRAKE RELEASE SWITCHES

ELECTRIC

Service — An inoperative switch must be replaced.

Switch replacement is identical to standard brake lamp

switch replacement.

Adjustment- The brake switch plunger must clear the

pedal arm when the arm is moved 1/4 inch measured at

the switch (Figure 7).

VACUUM

Service
—
An inoperative (sticking, plugged, or leaking)

switch must be replaced. Switch replacement is similar
to brake switch replacement. Be certain that the hose to

the switch is connected firmly and is not cracked or

deteriorated.

Adjustment- The brake switch plunger must clear the

pedal arm when the arm is moved 5/16 inch measured at

the switch (Figure 7).

ENGAGEMENT SWITCH

Service

replacement.
The engagement is serviced only by

Removal

1.
Pry the engagement button out of the turn signal knob

with a small thin bladed screwdriver (Figure 2).

2.
With a small hook or long nosed pliers, remove the

switch retaining ring.

3.
.Pull switch outward utilizing the slack in the wiring

harness.

4.
With a small soldering iron, unsolder the wires and

resolder them to the correct terminals of the re-

placement switch.

CHEVROLET CHASSIS SERVICE MANUAL