tire type CHEVROLET CAMARO 1967 1.G Chassis Workshop Manual

LUBRICATION 0-16

Every 12,000 miles (more frequently*, depending on

severity of service, if vehicle is used to pull trailers,

carry full loads during high ambient temperatures,

operate in mountainous terrain or operate under other

severe conditions--Remove fluid from the transmission

sump and add one and a half quarts of fresh fluid for

Camaro and Chevy II and two quarts for Chevrolet,

Chevelle, and Corvette. Operate transmission through all

ranges and check fluid level as described above.

•Except if vehicle is equipped with transmission pro-

vided in heavy duty service options. If so equipped,

drain converter and pump every 12,000 miles and add

approximately seven and a half quarts of fresh fluid

for Chevy II and nine quarts for Chevrolet and Chevelle.

TURBO HYDRA-MATIC

Lubrication. recommendations for the Turbo Hydra-

Matic are the same as outlined for the Powerglide

transmission except for fluid capacity and filter change

listed below.

After checking transmission fluid level it is important

that the dip stick be pushed all the way into the fill tube.

Every 12,000 miles — after removing fluid from the

transmission sump, approximately 7 1/2 pints of fresh

fluid will be required to return level to proper mark on

the dip stick.

Every 24,000 miles, or at every other fluid change--

the transmission sump strainer should be replaced.

FRONT WHEEL BEARINGS

It is necessary to remove the wheel and hub assembly

to lubricate the bearings. The bearing assemblies should

be cleaned before repacking with lubricant. Do not pack

the hub between the inner and outer bearing assemblies

or the hub caps, as this excessive lubrication results in

the lubricant working out into the brake drums and

linings.

Front wheels of all passenger car models are equipped

with tapered roller bearings and should be packed with a

high melting point water resistant front wheel bearing

lubricant whenever wheel and hub are removed.

CAUTION: "Long fibre" or "viscous" type

lubricant should not be used. Do not mix wheel

bearing lubricants. Be sure to thoroughly clean

bearings and hubs of all old lubricant before

repacking.

The proper adjustment of front wheel bearings is one

of the important service operations- that has a definite

bearing on safety. A car with improperly adjusted front

wheel bearings lacks steering stability, has a tendency to

wander or shimmy and may have increased tire wear.
The adjustment of these bearings is very critical. The

procedure is covered in Section 3 of this manual under

Front Wheel Bearings—Adjust,

MANUAL STEERING GEAR

Check lubricant level every 36,000 miles. If required,

add EP Chassis Lubricant.

POWER STEERING

On models equipped with power steering gear, check

fluid at operating temperature in pump reservoir. Add

GM Power Steering Fluid, or, if this is not available, use

Automatic Transmission Fluid "Type A" bearing the

mark AQ-ATF followed by a number and the suffix letter

'A'
to bring level to full mark on dip stick.

AIR CONDITIONING

After the first 6,000 miles, check all hose clamp

connections for proper tightness.

Every 6,000 miles check sight glass under the hood,

after the system has been in operation for several

minutes. Sight glass should be clear but may, during

milder weather, show traces of bubbles. Foam or dirt

indicate a leak which should be repaired immediately.

BRAKE MASTER CYLINDER

Check level every 6,000 miles and maintain 1/4" below

lowest edge of each filler opening with GM Hydraulic

Brake Fluid Supreme No. 11.

PARKING BRAKE

Every 6,000 miles, apply water resistant lube to park-

ing brake cable, cable guides and at all operating links

and levers.

CLUTCH CROSS-SHAFT

Periodic lubrication of the clutch cross shaft is not

required. At 36,000 miles or sooner, if necessary;

remove plug, install lube fitting and apply CHASSIS

LUBRICANT.

CHASSIS LUBRICATION

For chassis lubrication, consult the lubrication chart.

It shows the points to be lubricated and how often the

lubricant should be applied.

The term "chassis lubricant" as used in this manual,

describes a water resistant EP chassis grease designed

for application by commercial pressure gun equipment.

CHEVROLET CHASSIS SERVICE MANUAL

CORVETTE BODY
1B-6

ASH TRAY

SET SCREW

(PART
OF
KNOB)
TENSION

ADJUSTING

SCREWS

Fig.
8—Console Trim

cracks",
the
windshield opening must
be
carefully

checked
for
irregularities
and
deformation.
To
check

windshield opening proceed
as
follows:

1.
With weatherstrip
and all
foreign material removed

from perimeter
of
opening and with molding clips
in

place, install windshield checking blocks (Special

Tool J-8942)
as
shown in Figure 17. Note that check-

ing blocks must
be
placed over molding clips
to

obtain proper alignment.

2.
Place
a new
windshield glass
in
opening, resting on

J-8942 blocks
as
shown in Figure
18.

3.
Check
fit of
glass carefully. Space between glass

and frame should not vary more than 1/8".

4.
Mark
and
repair
any
imperfections. Recheck
fit as

required.

Fig.
9—Special Clip
Fig.
10—Sun Visor and Inside Rear View Mirror

Installation

1.
Carefully clean
all
loose material
out of
windshield

frame
(fig. 19).

2.
Install
new
molding clips (Item
9, fig. 12).
Both

models
use 13
type
B
clips equally spaced on lower

frame section.
37
Models use 11 type A clips equally

spaced on the top frame section.

3.
Apply
a
bead
of gun
grade body sealer such
as

3M-1170
in
apex
of
windshield frame
as
shown
in

Figure
20.

4.
Install weatherstrip on windshield glass.

5. Starting
at
bottom center
of
glass, insert
a
piece
of

heavy cord such
as
chalk line,
etc. in
groove
of

weatherstrip.
Cut
cord long enough so that about 10"

of free length exists after going around windshield.

Knot ends
of
cord together where they meet at bot-

tom center
of
glass
and
draw knot into groove
(fig.

21).
Tape loose ends
to
inside surface
of
glass
as

shown.

6. Place weatherstrip windshield assembly
in
wind-

shield frame. From inside
of
vehicle grasp ends
of

cord and pull toward you.
It is
wise to have an assis-

tant exert gentle
but
firm pressure
on
outside sur-

face
of
glass
in the
area where string
is
emerging

from weatherstrip. Figure
22
illustrates action
of

string
on
weatherstrip.
Lip of
seal
is
pulled out of

frame apex and over pinchweld flange.

7. When string
has
been removed, carefully inspect

seating
of lip
over entire perimeter
of
windshield,

paying particular attention to corners.

8. Apply
2
beads
of
sealer on outer surface
of
weather-

strip
as
shown
in
Figure
23.
Inject
a
moderate

quantity
of
windshield cement such
as
3M-6699B

between windshield glass
and
weatherstrip using

pressure gun
as
shown
in
Figure
23.

9. Install lower reveal molding, aligning
it
with mark

made upon disassembly. Refer
to
Figure
12,
View

A, before attempting installation; note that flange
of

molding
and
clips (item
9) at
ends
of
molding must

pass between molding retaining clips and windshield

frame.
li
difficulty
is met in
engaging molding

flange with retaining clips,
a
piece
of
shim stock

may
be
used
as a
"shoe horn"
to
place flange be-

hind clips.

10.
Install
in
order named: Upper reveal molding (align-

ing marks made
at
disassembly); side weatherstrip

CHEVROLET CHASSIS SERVICE MANUAL

CORVETTE BODY 1B-44

VIEW A

VIEW B

Fig.
97—Weatherstrip and Drip Moldings

1.
Headlining

2.
Roof Panel

3. Cap

4.
Drip Molding -

Side
5. Weatherstrip Assembly

- Inner Side

6. Weatherstrip Assembly

- Retaining Screw
7. Weatherstrip Assembly

- Retaining Screw Special

8. Weatherstrip Assembly

- Outer
9. Weatherstrip Assembly - Inner Forward

10.
Drip Molding - Forward

11.
Retainer - Weatherstrip Assembly,

Outer

Installation

1.
Wipe roof panel with a Xylol solvent such as 3M

Adhesive cleaner or equivalent, should be used to

remove or smooth but excess old cement. Apply

solvent and allow to soak before rubbing.

2.
Where possible, install new cover at room tempera-

ture (approximately 72 s) to permit easier fitting and

removing of wrinkles from the cover assembly.

3.
Determine center line of roof panel by marking

center points on front of hard top and back window

opening. Fold cover lengthwise. Lay cover on roof

panel. Determine overhang (approximately 1").

4.
Apply nitrile non-staining vinyl trim adhesive (such

as 3M Vinyl Trim Adhesive) to the ropf panel ad-

jacent to center line of fabric roof cover. *

5V Application of nitrile vinyl trim cement should be as

thin as possible. An excessive amount of cement may

result in trapped solvents (blisters) between fabric
cover and roof panel. A mohair roller should be used

for thin adhesive application.

NOTE:
If nitrile non-staining cement is not

available, neoprene type non-staining weather-

strip cement (3M weatherstrip cement or

equivalent) may be used.

6. Apply cement to entire fabric roof cover.

NOTE:
Allow approximately 15 minutes for

7.
cement to dry.

Fold vinyl cover back to contact adhesive on roof

panel. Vinyl cover seam must be parallel to center-

line of vehicle.

8. Repeat above steps for opposite side of
roof.

9. Use suitable spatula or roller to remove wrinkles

and/or bubbles from vinyl cover.

10.
Trim excess vinyl around entire top to provide a

CHEVROLET CHASSIS SERVICE MANUAL

FRONT SUSPENSION 3-5

FRONT END ALIGNMENT

Front end alignment, that is alignment of the inter-

related steering components of the front suspension sys-

tem, must be correctly maintained to assure ease and

stability of steering and satisfactory tire life.

Alignment Preliminary Steps

Several different types of machines are available for

checking all the factors of front end alignment. The in-

structions furnished with each particular machine should

be followed. In all cases, however, checks should be

made with the vehicle level and at curb weight.

Since steering complaints are not always the result of

improper alignment a check should be made to see if any

of the following conditions exist. Any such conditions

should be corrected before proceeding further.

1.
Steering gear loose or improperly adjusted.

2.
Steering gear housing loose at frame.

3.
Excessive wear or play in spherical joints or steer-

ing shaft coupling.

4.
Tie rod or steering connections loose.

5.
Improper front spring heights.

6. Unbalanced or underinflated tires.

7.
Improperly adjusted wheel bearings.

8. Shock absorbers not operating properly.

Wheel alignment should always be made with the vehi-

cle rolled forward taking out any slack in the same man-

ner as when the vehicle is traveling forward.

Caster and Camber Adjustment

NOTE: Before adjusting caster and camber

angles, the front bumper should be raised and

quickly released to allow car to return to its

normal height.

Chevelle, Camaro and Corvette

Caster and camber adjustments are made by means of

shims inserted between the upper control arm inner sup-

port shaft and the support bracket attached to the frame

(fig. 6). Shims may be added, subtracted or transferred

to change the readings as follows:
Fig.
6 - Caster and Camber Adjustment - Chevelle

Typical of Corvette and Camaro

Caster - change shims at either the front or rear of

the shaft.

The addition of shims at the front bolt or removal

of shims at the rear bolt will decrease positive

caster. One shim (1/3 2") will change caster (ap-

prox.) 1/4°.

Camber - change shims at both the front and rear of

the shaft.

Adding an equal number of shims at both front and

rear of the support shaft will decrease positive cam-

ber. One shim (1/32") at each location will move

camber (approx.) 1/5° (Chevelle and Camaro); 1/6°

(Corvette).

TIGHTEN TO LOCK

ADJUSTMENT

Fig.
7 - Caster and Camber Adjustment Points - Chevrolet

CHEVROLET CHASSIS SERVICE MANUAL

FRONT SUSPENSION 3-18

CHEVROLET
CHEVELLE

CAMARO (TYPICAL)

CHEVY U
LOWER CONTROL ARM

CORVETTE

Fig.
30 - Lower Control Arm Attachment

2.
Raise lower control arm and insert ball stud into

steering knuckle lower boss. Install nut and insert

new cotter pin. Install stabilizer linkage.

Lube Fittings

Special self threading type lube fittings are used in the

spherical joint assemblies. If it is necessary to replace

a fitting a standard threaded type may be used. However,

replacement spherical joint assemblies are supplied less

the lube fitting. Therefore it will be necessary to install

a self threading type fitting into the untapped hole pro-

vided when replacing the entire assembly.

LOWER CONTROL ARM

Chevrolet (Fig. 30)

Removal

1.
Remove the coil spring as outlined previously.

2.
Remove lower control arm ball stud cotter pin and

loosen nut. Loosen the ball stud, then remove nut

and lower control arm.

CAUTION: Use extreme care not to damage

the seal during this operation.
Installation

1.
Insert lower control arm ball stud into the steering

boss,
install the nut and insert new cotter pin.

2.
Install the coil spring as outlined previously.

3.
Tighten nuts to torque shown in Specifications.

Chevelle and Camaro (Fig. 30)

Removal

1.
Remove the front coil spring as outlined previously.

2;
Remove the two control arm to frame and cross-

member bracket attaching bolts and lock washers.

3.
Remove the lower control arm assembly.

Installation

1.
With the control arm in place in frame and cross-

member brackets, install the front and rear attaching

bolts,
nuts and lock washers.

2.
Install the coil spring as outlined under "Front Coil

Spring - Installation".

3.
Tighten the nuts to torque shown in Specifications.

Chevy II (Fig. 30)

Removal

1.
With vehicle weight still on front wheels, install

CHEVROLET CHASSIS SERVICE MANUAL

FRONT SUSPENSION
3-22

CHEVROLET

s-L 1 \
TYPICAL
OF

-^-x ^K CORVETTE, CHEVELLE AND CAMARO

CHEVY n

Rg.
37 - Upper Control Arm Attachment

NOTE:
Additional support to upper control

arm may be necessary while chiseling.

7. Clean ball joint seat in arm and inspect for cracking

or other evidence of fatigue. If cracks are present at

the rivet holes or ball joint opening, replace arm as

outlined later in this section.

8. Attach replacement ball joint assembly to the control

arm, using special bolts furnished with replacement

kit.

NOTE:
Use only special hardened bolts fur-

nished with this replacement kit. Do not attempt

to use other non-hardened bolts and do not at-

tempt to rivet replacement ball joint to arm.
9. Raise lower control arm and steering knuckle as-

sembly into position, insert upper ball stud into up-

per steering knuckle and install stud nut. Torque

nut as shown in the specifications and insert new

cotter pin. Install stabilizer and strut rod.

10.
Lubricate ball joint, install wheel and tire and re-

move adjustable jackstand.

11.
Lower vehicle and remove upper control arm spacer.

12.
Check and readjust caster and camber angles where

necessary.

LUBE FITTINGS

Special self threading type lube fittings are used in the

spherical joint assemblies. If it is necessary to replace

a fitting a standard threaded type may be used. However,

replacement spherical joint assemblies are supplied less

the lube fitting. Therefore it will be necessary to install

a self threading type fitting into the untapped hole pro-

vided when replacing the entire assembly.

UPPER CONTROL ARM

Chevrolet, Chevelle, Camaro and Corvette

(Fig.
37)

Removal

1.
Support vehicle weight at outer end of lower control

arm.

2.
Remove wheel and tire assembly.

3.
Remove cotter pin and nut from upper control arm

ball stud. ,

4.
REMOVE The stud from knuckle.

5. Remove two nuts retaining upper control arm shaft to

front crossmember. (Chevelle, Camaro and Cor-

vette—Note number of shims at each bolt.)

6. Remove the bolts attaching the control arm to the

frame to allow proper clearance for control arm

removal if necessary.

7. Remove upper control arm from vehicle.

Installation

1.
Install upper control arm in vehicle.

2.
Install nuts, bolts and lock washers retaining upper

control arm shaft to frame. (Chevelle, Camaro and

Corvette—Install same number of shims as removed

at each bolt.)

3.
Torque nuts as shown in the Specifications at the end

of this book.

4.
Install ball stud through knuckle, install nut, tighten

and install cotter pin.

5. Install wheel and tire assembly.

6. Lower vehicle to floor.

7. Bounce front end of vehicle to centralize bushings

and tighten bushing collar bolts as shown in the

Specifications.

Chevy II (Fig. 37)

Removal

1.
Remove spring and shock absorber as outlined above.

2.
Position adjustable jackstand under lower control

arm.

3.
Remove cotter pin and nut from upper ball joint stud

and strike steering knuckle boss to loosen stud.

4.
Drop lower control arm and steering knuckle

assembly.

CHEVROLET CHASSIS SERVICE MANUAL

REAR SUSPENSION AND DRIVE LINE 4-29

REAR AXLE NOISE DIAGNOSIS

Mechanical failures of the rear axle are relatively

simple to locate and correct. Noise in a rear axle is a

little more difficult to diagnose and repair. One of the

most essential parts of rear axle service is proper

diagnosis.

Ail rear axles are noisy to a certain degree. The

action of transmitting the high engine torque through a

90° turn reducing propeller shaft speed produces noise

in rear axles. This point establishes the need for a line

between normal and abnormal or unacceptable axle

noises.

Slight axle noise heard only at a certain speed or under

remote conditions must be considered normal. Axle noise

tends to "peak" at varying speeds and the noise is in no

way indicative of trouble in the axle.

If noise is present in an objectionable form, loud or at

all speeds, an effort should be made to isolate the noise

as being in one particular unit of the vehicle. Axle noise

is often confused with other noises such as tire noise,

transmission noise, propeller shaft vibration and uni-

versal joint noise. Isolation of the noise as in any one

unit requires skill and experience. An attempt to elimini-

ate a slight noise may baffle even the best of diagnos-

ticians. Such practices as raising tire pressure to

eliminate tire noise, listening for the noise at varying

speeds and on drive, float and coast, and under proper

highway conditions, turning the steering wheel from left

to right to detect wheel bearing noise, will aid even the

beginner in detecting alleged axle noises. Axle noises

fall into two categories: gear noise and bearing noise.

GEAR NOISE

Abnormal gear noise can be recognized since it pro-

duces a cycling pitch and will be very pronounced in the

speed range at which it occurs, appearing under either

"drive," "float" or "coast" conditions. Gear noise

tends to peak in a narrow speed range or ranges, while

bearing noise will tend to remain constant in pitch. Ab-

normal gear noise is rare and usually originates from

the scoring of the ring gear and pinion teeth as a result

of insufficient or improper lubrication in new assemblies.

Side gears seldom give trouble as they are used only

when the rear wheels travel at different speeds.

BEARING NOISE

Defective bearings will always produce a whine that is

constant in pitch and varies with vehicle speed. This fact

will allow you to distinguish between bearing noise and

gear noise.

1.
Pinion bearing noise resulting from a bearing failure

can be identified by a constant rough sound. Pinion

bearings are rotating at a higher speed than differen-

tial side bearings or axle shaft bearings. This

particular noise can be picked up best by testing the

car on a smooth road (black top). However, care

should be taken not to confuse tire noise with bear-

ing or gear noise. If any doubt exists, tire treads

should be examined for irregularities that would

produce such noise.

2.
Wheel bearing noise may be confused with rear axle

noise. To differentiate between wheel bearings and

rear axle, drive the vehicle on a smooth road at

medium-low speed. With traffic permitting, turn
Fig.
74—Scored Hypoid Ring Gear

the vehicle sharply right and left. If noise is caused

by wheel bearings, it will increase in the turns be-

cause of the side loading. If noise cannot be isolated

to front or rear wheel bearings, inspection will be

necessary.

3.
Side bearings will produce a constant rough noise of

a slower nature than pinion bearings. Side bearing

noise will not fluctuate in the above wheel bearing

test.

Failure Analysis

The most common types of rear axle failures are

hypoid gear tooth scoring and fracture, differential gear

fracture. and/or differential bearing failure, and axle

shaft bearing failure.

Fig.
75-Cracked Hypoid Ring Gear

CHEVROLET CHASSIS SERVICE MANUAL

REAR SUSPENSION AND DRIVE LINE 4-37

9. Connect spring end link bolts as outlined under

Spring--Installation, in this section.

10.
Remove filler plug, located on right side of cover,

and fill -with hypoid lubricant to level of filler hole.

11.
Lower vehicle and road test for leaks, noise and

general performance.

POSITRACTION DIFFERENTIAL UNIT

The optionally available Positraction differential unit

is installed in the conventional carrier to replace the

standard differential unit.

Service procedures for the Positraction equipped axle

are the same as on a conventional axle except for the.

operations listed below.

On the Vehicle Check

If vehicle is equipped with a manual transmission, shift

transmission into neutral.

1.
Raise rear of vehicle until wheels are off the ground,

remove one wheel and tire assembly.

2.
Attach Adapter J-5748 to axle shaft flange and install

a
1/2-13
bolt into adapter (fig. 97).

3.
With wheel and tire assembly still on vehicle held

firmly to prevent turning, measure torque required
Fig.
97—Measuring Positraction Rotating Torque

to rotate opposite axle shaft with a 0-150# torque

wrench attached to J-5748. Torque should be 70

ft.
lbs. minimum new, and no less than 40 ft. lbs. if

used.

PROPELLER SHAFT AND UNIVERSAL JOINTS

INDEX

Page
Page

General Description 4-37

Component Parts Replacement. 4-38

Propeller Shaft (Dana) 4-38

Removal 4-38

Repairs 4-38
Installation 4-39

Propeller Shaft (Saginaw) 4-40

Removal 4-40

Repairs 4-40

Installation 4-41

GENERAL DESCRIPTION

The one-piece, exposed-type, tubular propeller shaft is

used on all models. The cardon-type universal joints are

of the extended-life design and do not require periodic

maintenance. A splined front yoke on the front end of the

propeller shaft extends into a splined coupling on the

transmission output shaft. This slip joint permits slight

lengthening and shortening of the propeller shaft to com-

pensate for up and down movement of the rear axle
assembly.

A light duty (fig. 98) and a heavy duty (fig. 99) version

of the tubular propeller shaft is used. The heavy-duty

shaft incorporates a damper, as part of the sleeve yoke,

at the transmission end of the shaft. This damper is not

serviced separately—the sleeve and damper (fig. 100)

must be replaced as an assembly.

Two different methods are used to retain the trunnions

Fig.
98—Light-Duty Propeller Shaft Cross-Section (Dana Design)

CHEVROLET CHASSIS SERVICE MANUAL

BRAKES

SECTION 5

CONTENTS OF THIS SECTION

Duo Servo Brakes

Disc Brakes
Page

5-1 Power Brakes

5-24 Special Tools
Page

5-31

5-32

DUO-SERVO BRAKES

INDEX

Page

General Description 5-1

Maintenance and Adjustments 5-3

Hydraulic Brake Fluid .. . 5-3

Bleeding Hydraulic System 5-3

Pressure Bleeding 5-3

Manual Bleeding 5_4

Push Rod to Main Cylinder Clearance 5-5

Hydraulic Brake Lines 5-5

Hydraulic Brake Hose 5-5

Hydraulic Brake Tubing 5-6

Brake Adjustment. .................... 5-7

Service Brake 5-7

Parking Brake 5-8

Component Replacement and Repairs 5-9

Parking Brake - Chevrolet, Chevelle and

Camaro 5^9

Pedal Assembly 5-9

Front Cable ,. . . 5-9

Center Cable 5-9

Rear Cables. . 5-9
Parking Brake - Chevy n 5-9

Lever Assembly 5-9

Idler Lever 5-11

Front Cable 5-11

Rear Cable . . ; 5-12

Parking Brake - Corvette 5-13

Lever Assembly . . . . 5-13

Front Cable 5-14

Rear Cable . . 5-14

Brake Pedal 5-15

Shoes and Linings 5-16

Organic 5-16

Metallic 5-17

Main Cylinder 5-18

Wheel Cylinders 5-21

Anchor Pin 5-22

Front Wheel 5-22

Rear Wheel 5-22

Brake Drums • 5-22

Brake Pipe Distribution and Switch Assembly . . . . . 5-23

Camaro Pressure Regulator Valve 5-23

GENERAL DESCRIPTION

All 1967 models are equipped with a new split brake

system as a safety feature. If a wheel cylinder or brake

line should fail at either the front end or rear end of

the vehicle, the operator can still bring the vehicle to

a controlled stop. The system is designed with separate

hydraulic systems for the front and rear brake using

a dual master cylinder (fig. 1). The design of the master

cylinder is similar to that used on the 1966 Corvette

in that it has two entirely separate reservoirs and outlets

in a common body casting. The front reservoir and outlet

is connected to the front wheel brakes, and the rear

reservoir and outlet is connected to the rear wheel

brakes. Two pistons within the master cylinder receive

mechanical pressure from the brake pedal push rod and

transmit it through the brake lines as hydraulic pressure

to the wheel cylinders. The filler cap is accessible from

inside the engine compartment.

A new brake pipe distribution and switch assembly

is mounted below the main cylinder. The front and rear

hydraulic brake lines are routed from the main cylinder,

through the brake pipe distribution and switch assembly,

to the front and rear brakes as shown in Figure 2. The

switch is wired electrically to the brake alarm indicator

light on the instrument panel. In the event of fluid loss

in either the front or rear brake system the indicator

on the instrument panel will illuminate red. (The indi-
cator will also' be illuminated when the parking brake is

applied.)

On Camaro models equipped with air conditioning, the

rear brake hydraulic line is routed through a pressure

regulator valve mounted on the left frame side rail

(fig. 3). The valve controls the hydraulic pressure to

the rear brakes resulting in the correct pressure balance

between the front and rear hydraulic systems.

The self-adjusting brakes (fig. 4), used on both front

and rear of all models, are the Duo-Servo single anchor

type which utilize the momentum of the vehicle to assist

in the brake application. The self-energizing or
self-

actuating force is applied to both brake shoes at each

wheel in both forward and reverse motion. The brake

shoe linings are bonded to the shoes.

Wheel cylinders are the double piston type permitting

even distribution of pressure to each brake shoe. To

keep out dust and moisture, both ejads of each wheel

cylinder are sealed with a rubber booC The wheel

cylinders have no adjustments.

The Chevrolet, Chevelle, and Camaro parking brakes

have a foot operated ratchet type pedal mounted to the

left of the steering column. A cable assembly connects

the pedal to an intermediate cable by means of an equal-

izer, where the adjustment for the parking brake is

incorporated. The intermediate cable attaches to the

CHEVROLET CHASSIS SERVICE MANUAL

BRAKES 5-22

2.
Replace ail push rods and pull back springs.

3.
Connect hose or line to wheel cylinder.

NOTE:
If replacing front wheel cylinder, con-

nect hose and inspect installation as outlined in

"Hydraulic Brake Hose Replacement".

4.
Install drum and wheel.

5. Bleed brakes as outlined in this section.

ANCHOR PIN

Front Wheel

1.
Raise front of vehicle and place on jack stands.

2.
Remove wheel and drum as outlined in this section.

3.
Remove brake shoe pull back springs, link and guide

plate.

4.
Disengage anchor pin lock and remove anchor pin by

turning counterclockwise.

5. Place new lock plate on anchor pin and pass pin

through the hole in flange plate and screw into tapped

hole in spindle support.

6. Torque pin to 130 lb. ft. and lock by peening over

washer tabs.

7. Install brake shoe guide plate, link and pull back

springs.

8. Adjust brakes, install drum and wheel as outlined

in this section. Test brake operation.

Rear Wheel

Two type anchor pins are used in production for the

rear wheels. The riveted type is not serviced and if

failure or damage should occur to either the anchor

pin or flange plate, both parts will have to be replaced

and the threaded type anchor pin used.

Threaded Type

1.
Raise rear of vehicle and place on jack stands,

2.
Remove wheel and drum as outlined in this section.

3.
Remove brake shoe pull back springs, link and guide

plate.

4.
Remove anchor pin retaining nut and washer and

remove pin from flange plate.

5. Position anchor pin to flange plate, install lock

washer and nut, and torque pin to 80 lb. ft.

6. Install brake shoe guide plate, link and pull back

springs.

7. Adjust brakes and install drum and wheel as outlined

in this section.

8. Test brake operation.

BRAKE DRUMS

Front brake drums are the demountable type; that is,

they can be removed without removing the hub. Rear

brake drums are demountable and may be removed

wihtout removing the axle shaft.

A lanced "knock out" area (fig. 34) is provided in

the web of the brake drum for servicing purposes in

the event retracting of the brake shoes is required in

order to remove the drum.

A small screw driver or hooked wire may be inserted

to disengage the automatic adjuster actuating lever so

the star wheel may be turned.

Removal

1.
Raise vehicle and place on jack stand.
2.
Remove wheel and tire assembly, back off brake

adjustment and remove drum.

Inspection and Reconditioning

Whenever brake drums are removed they should be

thoroughly cleaned and inspected for cracks, scores,

deep grooves, and out-of-round. Any of these conditions

must be corrected since they can impair the efficiency

of brake operation and also can cause premature failure

of other parts.

Smooth up any slight scores by polishing with fine

emery cloth. Heavy or extensive scoring will cause

excessive brake lining wear and it will probably be

necessary to rebore in order to true up the braking

surface.

An out-of-round drum makes accurate brake shoe

adjustment impossible and is likely to cause excessive

wear of other parts of brake mechanism due to its

eccentric action.

A drum that is more than .008" out-of-round on the

diameter is unfit for service and should be rebored.

Out-of^round, as well as taper and wear can be ac-

curately measured with an inside micrometer fitted

with proper extension rods.

If drum is to be rebored for use with standard size

brake facings which are worn very little, only enough

metal should be removed to obtain a true smooth braking

surface.

If drum has to be rebored more than .020" over the

standard diameter, it should be rebored to .060" diameter

oversize and the brake facing should be replaced with

.030"
oversize facings.

A brake drum must not be rebored more than .060"

over the maximum standard diameter, since removal

of more metal will effect, dissipation of heat and may

cause distortion of drum. Chevrolet brake facing is

not furnished larger than .030" oversize and this will

not work efficiently in drums bored more than .060"

oversize.

Brake drums may be refinished either by turning or

grinding. Best brake performance is obtained by turning

drums with a very fine feed. To insure maximum lining

life,
the refinished braking surface must be smooth and

free from chatter or tool marks, and run-out must not

exceed .005" total indicator reading.

Cleaning

New brake drums in parts stock are given a light.

coating of rust proofing oil to prevent the formation of

rust on the critical braking surfaces during the time

that the drums are in storage.

This rust proofing oil must be carefully removed

before the drum is placed in service to prevent any

of this oil from getting on the brake shoe facings, which

might cause an extreme brake grab condition.

It is recommended that a suitable volatile, non-toxic,

greaseless type solvent be used to clean the oil from the

braking surface of the new brake drums before they are

•placed in service to insure the cleanest possible surface.

Gasoline or kerosene should not be used as there is

danger that a portion of the diluated oil substance may

be left on the braking surface that may later cause

difficulty.

Installation

1.
Make brake adjustment as outlined in this section.

CHEVROLET CHASSIS SERVICE MANUAL