Citroen C3 PICASSO DAG 2008.5 1.G Owner's Manual
Page 141 of 207
128
PRACTICAL INFORMATION
Engine compartment fuses
The fuse box is placed in the engine
compartment near the battery (left-hand
s i d e ) .
Access to the fuses
U n c l i p t h e c o v e r .
Change the fuse (see correspond-
i n g p a r a g r a p h ) .
W h e n y o u h a v e fi n i s h e d , c l o s e t h e
cover carefully to guarantee the
s e a l i n g o f t h e f u s e b o x . Fuse table
Fuse N° Rating Functions
F1 20 A Engine control unit supply, cooling fan unit control,
m u l t i f u n c t i o n e n g i n e c o n t r o l m a i n r e l a y .
F2 15 A H o r n .
F3 10 A F r o n t / r e a r w a s h - w i p e .
F4 20 A D a y t i m e r u n n i n g l a m p s .
F5 15 A D i e s e l h e a t e r ( d i e s e l e n g i n e ) , f u e l p u m p ( p e t r o l
engine)
F6 10 A ABS/ESP control unit, ABS/ESP cut-off relay,
s e c o n d a r y s t o p s w i t c h .
F7 10 A E l e c t r i c a l p o w e r s t e e r i n g .
F8 25 A S t a r t e r c o n t r o l .
F9 10 A S w i t c h i n g a n d p r o t e c t i o n u n i t ( D i e s e l ) .
F10 30 A D i e s e l e n g i n e i n j e c t i o n p u m p v a l v e , i n j e c t o r s a n d
ignition coils (petrol engine)
F11 40 A A i r c o n d i t i o n i n g b l o w e r .
Page 142 of 207
129
PRACTICAL INFORMATION
Fuse N° Rating Functions
F12 30 A W i n d s c r e e n w i p e r s s l o w / f a s t s p e e d .
F13 40 A B u i l t - i n s y s t e m s i n t e r f a c e s u p p l y ( i g n i t i o n p o s i t i v e ) .
F14 30 A V a l v e t r o n i c s u p p l y ( p e t r o l ) .
F15 10 A R i g h t - h a n d m a i n b e a m h e a d l a m p .
F16 10 A L e f t - h a n d m a i n b e a m h e a d l a m p .
F17 15 A L e f t - h a n d d i p p e d h e a d l a m p .
F18 15 A R i g h t - h a n d d i p p e d h e a d l a m p .
F19 15 A Multifunction engine control supply (petrol engine),
a i r c o o l i n g s o l e n o i d v a l v e s ( D i e s e l ) .
F20 10 A Multifunction engine control supply (petrol engine),
T u r b o p r e s s u r e r e g u l a t i o n v a l v e ( D i e s e l ) , e n g i n e
c o o l a n t l e v e l d e t e c t o r ( D i e s e l ) .
F21 5 A Fan assembly control supply, APC, ABS ESP
r e l a y s .
Page 143 of 207
130
PRACTICAL INFORMATION
Table of maxi-fuses
Fuse N° Rating
Functions
MF1 * 60 A F a n a s s e m b l y .
MF2 * 30 A A B S / E S P c o n t r o l u n i t .
MF3 * 30 A A B S / E S P c o n t r o l u n i t .
MF4 * 60 A B u i l t - i n S y s t e m s I n t e r f a c e ( B S I ) s u p p l y .
MF5 * 60 A B u i l t - i n S y s t e m s I n t e r f a c e ( B S I ) s u p p l y .
MF6 * - N o t u s e d .
MF7 * - P a s s e n g e r c o m p a r t m e n t f u s e b o x .
MF8 * - N o t u s e d .
* T h e m a x i - f u s e s p r o v i d e a d d i t i o n a l p r o t e c t i o n f o r t h e e l e c t r i c a l s y s t e m s . A l l w o r k o n t h e m a x i - f u s e s m u s t b e c a r r i e d o u t b y a
C I T R O Ë N d e a l e r .
Page 144 of 207
131
PRACTICAL INFORMATION
BATTERY
Procedure for charging your battery
w h e n i t i s fl a t o r f o r s t a r t i n g t h e e n g i n e
u s i n g a n o t h e r b a t t e r y .
Access to the battery Starting using another battery
Connect the red cable to the posi-
t i v e t e r m i n a l ( + ) o f t h e fl a t b a t t e r y A ,
then to the positive terminal (+) of
the slave battery B .
Connect one end of the green or
black cable to the negative terminal
(-) of the slave battery B .
Connect the other end of the green
or black cable to the negative termi-
n a l ( - ) o f t h e fl a t b a t t e r y A .
S t a r t t h e s l a v e v e h i c l e .
Operate the starter of the broken
down vehicle and let the engine
r u n .
Wait until the engine returns to idle
a n d d i s c o n n e c t t h e c a b l e s .
The battery is located under the bon-
n e t .
To gain access to it:
open the bonnet using the interior
lever, then the exterior lever,
secure the bonnet strut,
remove the plastic cover to gain ac-
cess to the two terminals,
unclip the fuse box to remove the
b a t t e r y , i f n e c e s s a r y .
Page 145 of 207
i
!
!
132
PRACTICAL INFORMATION D o n o t d i s c o n n e c t t h e t e r m i n a l s
w h i l e t h e e n g i n e i s r u n n i n g .
D o n o t c h a r g e t h e b a t t e r i e s w i t h o u t
d i s c o n n e c t i n g t h e t e r m i n a l s fi r s t .
The batteries contain harmful sub-
stances such as sulphuric acid and
l e a d . T h e y m u s t b e d i s p o s e d o f i n
accordance with regulations and
must not, in any circumstances, be
d i s c a r d e d w i t h h o u s e h o l d w a s t e .
Take used remote control batteries
and vehicle batteries to a special
c o l l e c t i o n p o i n t .
Charging the battery using a
battery charger
D i s c o n n e c t t h e b a t t e r y f r o m t h e v e -
h i c l e .
Follow the instructions for use pro-
vided by the manufacturer of the
c h a r g e r .
Reconnect starting with the nega-
t i v e t e r m i n a l ( - ) .
Check that the terminals and connec-
t o r s a r e c l e a n . I f t h e y a r e c o v e r e d w i t h
sulphate (whitish or greenish deposit),
r e m o v e t h e m a n d c l e a n t h e m .
At the risk of discharging the bat-
tery, the deactivated functions can
b e r e a c t i v a t e d m a n u a l l y .
System which manages the use of cer-
tain functions in relation to the level of
c h a r g e r e m a i n i n g i n t h e b a t t e r y .
When the vehicle is being driven, the
load reduction function temporarily deac-
tivates certain functions, such as the air
c o n d i t i o n i n g , t h e r e a r s c r e e n d e - i c i n g . . .
The deactivated functions are reacti-
vated automatically as soon as condi-
t i o n s p e r m i t .
It is advisable to disconnect the
battery if the vehicle is to be left un-
u s e d f o r m o r e t h a n o n e m o n t h . Before disconnecting the battery
Wait 2 minutes after switching off
the ignition before disconnecting
t h e b a t t e r y .
Close the windows and the doors
b e f o r e d i s c o n n e c t i n g t h e b a t t e r y .
Following reconnection of the
battery
Following reconnection of the bat-
tery, switch on the ignition and wait
1 minute before starting to permit
initialisation of the electronic sys-
t e m s . H o w e v e r , i f s l i g h t d i f fi c u l t i e s
are encountered following this op-
e r a t i o n , c o n t a c t a C I T R O Ë N d e a l e r .
Referring to the corresponding sec-
tion, you must yourself reinitialise:
- the remote control key,
- the GPS satellite navigation
s y s t e m .
Page 146 of 207
i
!
!
132
PRACTICAL INFORMATION D o n o t d i s c o n n e c t t h e t e r m i n a l s
w h i l e t h e e n g i n e i s r u n n i n g .
D o n o t c h a r g e t h e b a t t e r i e s w i t h o u t
d i s c o n n e c t i n g t h e t e r m i n a l s fi r s t .
The batteries contain harmful sub-
stances such as sulphuric acid and
l e a d . T h e y m u s t b e d i s p o s e d o f i n
accordance with regulations and
must not, in any circumstances, be
d i s c a r d e d w i t h h o u s e h o l d w a s t e .
Take used remote control batteries
and vehicle batteries to a special
c o l l e c t i o n p o i n t .
Charging the battery using a
battery charger
D i s c o n n e c t t h e b a t t e r y f r o m t h e v e -
h i c l e .
Follow the instructions for use pro-
vided by the manufacturer of the
c h a r g e r .
Reconnect starting with the nega-
t i v e t e r m i n a l ( - ) .
Check that the terminals and connec-
t o r s a r e c l e a n . I f t h e y a r e c o v e r e d w i t h
sulphate (whitish or greenish deposit),
r e m o v e t h e m a n d c l e a n t h e m .
At the risk of discharging the bat-
tery, the deactivated functions can
b e r e a c t i v a t e d m a n u a l l y .
System which manages the use of cer-
tain functions in relation to the level of
c h a r g e r e m a i n i n g i n t h e b a t t e r y .
When the vehicle is being driven, the
load reduction function temporarily deac-
tivates certain functions, such as the air
c o n d i t i o n i n g , t h e r e a r s c r e e n d e - i c i n g . . .
The deactivated functions are reacti-
vated automatically as soon as condi-
t i o n s p e r m i t .
It is advisable to disconnect the
battery if the vehicle is to be left un-
u s e d f o r m o r e t h a n o n e m o n t h . Before disconnecting the battery
Wait 2 minutes after switching off
the ignition before disconnecting
t h e b a t t e r y .
Close the windows and the doors
b e f o r e d i s c o n n e c t i n g t h e b a t t e r y .
Following reconnection of the
battery
Following reconnection of the bat-
tery, switch on the ignition and wait
1 minute before starting to permit
initialisation of the electronic sys-
t e m s . H o w e v e r , i f s l i g h t d i f fi c u l t i e s
are encountered following this op-
e r a t i o n , c o n t a c t a C I T R O Ë N d e a l e r .
Referring to the corresponding sec-
tion, you must yourself reinitialise:
- the remote control key,
- the GPS satellite navigation
s y s t e m .
Page 147 of 207
i
!
133
PRACTICAL INFORMATION
A fl a t b a t t e r y p r e v e n t s t h e e n g i n e
from starting (refer to the corre-
s p o n d i n g p a r a g r a p h ) .
If the telephone is being used at
the same time with the MyWay audio
navigation, it will be interrupted after
1 0 m i n u t e s .
ENERGY ECONOMY MODE
System which manages the duration of
use of certain functions to conserve a
s u f fi c i e n t l e v e l o f c h a r g e i n t h e b a t t e r y .
After the engine has stopped, you can
still use functions such as the audio
e q u i p m e n t , w i n d s c r e e n w i p e r s , d i p p e d
h e a d l a m p s , c o u r t e s y l i g h t s , e t c . f o r a
maximum combined duration of thirty
m i n u t e s . Exiting economy mode
These functions are reactivated auto-
m a t i c a l l y n e x t t i m e t h e v e h i c l e i s d r i v e n .
In order to resume the use of these
functions immediately, start the en-
g i n e a n d l e t i t r u n f o r a f e w m i n u t e s .
The time available to you will then be
double the duration for which the en-
g i n e i s l e f t r u n n i n g . H o w e v e r , t h i s p e r i o d
w i l l a l w a y s b e b e t w e e n fi v e a n d t h i r t y
m i n u t e s .
Switching to economy mode
Once the thirty minutes are over, a
message appears on the multi-function
display indicating that the vehicle has
switched to economy mode and the ac-
t i v e f u n c t i o n s a r e p u t o n s t a n d b y .
CHANGING A WIPER BLADE
Procedure for replacing a worn wiper
blade with a new one without the use
o f t o o l s .
Removing a front or rear wiper
blade
R a i s e t h e c o r r e s p o n d i n g w i p e r a r m .
U n c l i p t h e w i p e r b l a d e a n d r e m o v e i t .
Fitting a front or rear wiper blade
At the front, check the size of the
wiper blade as the shorter blade is
fi t t e d o n t h e r i g h t - h a n d s i d e o f t h e
v e h i c l e .
Put the corresponding new wiper
b l a d e i n p l a c e a n d c l i p i t .
F o l d d o w n t h e w i p e r a r m c a r e f u l l y .
Before removing a front wiper blade
Within one minute after switching off
the ignition, operate the wipers stalk
to position the wiper blades in the
v e r t i c a l p o s i t i o n .
This position must be used in order to
avoid damaging the wiper blade and the
b o n n e t .
After fitting a front wiper blade
S w i t c h o n t h e i g n i t i o n .
Operate the wipers stalk again to
p a r k t h e w i p e r b l a d e s .
Page 148 of 207
i!
134
PRACTICAL INFORMATION
TOWING THE VEHICLE
Access to the tools Towing your vehicle
On the front bumper, unclip the cover
b y p r e s s i n g a t t h e b o t t o m .
S c r e w t h e t o w i n g e y e i n f u l l y .
I n s t a l l t h e t o w b a r .
Switch on the hazard warning lights
o n t h e t o w e d v e h i c l e .
P l a c e t h e g e a r l e v e r i n n e u t r a l .
On the rear bumper, unclip the cover
b y p r e s s i n g a t t h e b o t t o m .
S c r e w t h e t o w i n g e y e i n f u l l y .
I n s t a l l t h e t o w b a r .
Switch on the hazard warning lights
o n t h e t o w e d v e h i c l e .
Towing another vehicle
The towing eye is installed under the
b o o t fl o o r .
To gain access to it:
open the boot,
r e m o v e t h e m o v a b l e b o o t fl o o r ,
lift up the boot carpet,
remove the towing eye from the tool
h o l d e r . When towing with all four wheels on
t h e g r o u n d , a l w a y s u s e a t o w b a r .
When towing with only two wheels
on the ground, always use profes-
s i o n a l l i f t i n g e q u i p m e n t .
When towing with the engine off,
there is no longer any braking or
s t e e r i n g a s s i s t a n c e .
Failure to observe this special con-
dition could result in damage to
certain braking components and
the absence of braking assistance
t h e n e x t t i m e t h e e n g i n e i s s t a r t e d .
Procedure for having your vehicle towed
or for towing another vehicle using a re-
m o v a b l e t o w i n g e y e .
Page 149 of 207
i
i
135
PRACTICAL INFORMATION
TOWING A TRAILER, A CARAVAN, ETC.
Your vehicle is primarily designed for
transporting people and luggage, but it
m a y a l s o b e u s e d f o r t o w i n g a t r a i l e r . Driving advice
The maximum towing load on a long
slope depends on the gradient and the
o u t s i d e t e m p e r a t u r e .
In all cases, pay attention to the coolant
t e m p e r a t u r e .
Side wind
Take into account the increased
s e n s i t i v i t y t o s i d e w i n d .
Cooling
Towing a trailer on a slope increases
t h e t e m p e r a t u r e o f t h e c o o l a n t .
As the fan is electrically controlled, its
cooling capacity is not dependent on
t h e e n g i n e s p e e d .
To lower the engine speed, reduce
y o u r s p e e d . Braking
Towing a trailer increases the braking
d i s t a n c e .
Tyres
Check the tyre pressures of the towing
vehicle and of the trailer, observing the
r e c o m m e n d e d p r e s s u r e s .
Lights
Check the electrical signalling on
t h e t r a i l e r .
The rear parking assistance will
be deactivated automatically if an
o r i g i n a l C I T R O Ë N t o w b a r i s u s e d .
If the warning light and the
STOP warning light come
on, stop the vehicle and
switch off the engine as
s o o n a s p o s s i b l e .
Towbar suited to the attachment of a
trailer or caravan with additional signal-
l i n g a n d l i g h t i n g .
Distribution of loads
D i s t r i b u t e t h e l o a d i n t h e t r a i l e r s o
that the heaviest items are as close
as possible to the axle and the nose
weight approaches the maximum
p e r m i t t e d w i t h o u t e x c e e d i n g i t .
Air density decreases with altitude, thus
r e d u c i n g e n g i n e p e r f o r m a n c e . A b o v e
1 000 metres, the maximum towing load
must be reduced by 10 % and so on for
e v e r y 1 0 0 0 m e t r e s o f a l t i t u d e .
R e f e r t o t h e " T e c h n i c a l D a t a " s e c t i o n f o r
details of the weights and towing loads
w h i c h a p p l y t o y o u r v e h i c l e .
D r i v i n g w i t h a t r a i l e r s u b j e c t s t h e t o w i n g
v e h i c l e t o m o r e s i g n i fi c a n t s t r e s s a n d i t s
d r i v e r m u s t b e p a r t i c u l a r l y c a r e f u l .
We recommend the use of original
CITROËN towbars and their har-
nesses that have been tested and
approved from the design stage
o f y o u r v e h i c l e , a n d t h a t t h e fi t -
ting of the towbar is entrusted to a
C I T R O Ë N d e a l e r .
I f t h e t r a i l e r i s n o t fi t t e d b y a
CITROËN dealer, it is imperative
t h a t i t i s fi t t e d u s i n g t h e e l e c t r i c a l
p r e - e q u i p m e n t i n s t a l l e d a t t h e r e a r
of the vehicle, in accordance with
t h e m a n u f a c t u r e r ’ s i n s t r u c t i o n s .
Page 150 of 207
i
136
PRACTICAL INFORMATION
FITTING ROOF BARS
Maximum authorised weight on
t h e r o o f r a c k : 6 0 k g .
If the height exceeds 40 cm, adapt
the speed of the vehicle to the
p r o fi l e o f t h e r o a d t o a v o i d d a m -
a g i n g t h e r o o f b a r s a n d t h e fi x i n g s
o n t h e r o o f .
Be sure to refer to national legis-
lation in order to comply with the
regulations for transporting ob-
jects which are longer than the
v e h i c l e .
T o fi t l o n g i t u d i n a l a n d / o r t r a n s v e r s e r o o f
b a r s , v i s i t y o u r C I T R O Ë N d e a l e r .