headlamp Citroen C4 PICASSO 2008.5 1.G User Guide

Page 103 of 330

88
V I S I B I L I T Y
V
Linked with the automatic
"Guide-me-home" lighting
Association with the automatic lighting
provides the "guide-me-home" lighting
with the following additional options:
- selection of the duration of main-taining of the lighting for 15, 30
or 60 seconds in the vehicle
parameters on the multifunc-
tion display confi guration menu
(in the case of the monochrome
screen A, the duration is fi xed),
- automatic activation of "guide- me-home" lighting when auto-
matic lighting is in operation.
Operating fault
In the event of a malfunction of the
brightness sensor, the lights come
on, a message appears on the mul-
tifunction display, accompanied by
an audible signal.
Consult a CITROËN dealer. In fog or snow, the brightness
sensor may detect suffi cient light.
Therefore, the lights will not come
on automatically.
Do not cover the brightness sen-
sor, linked with the rain sensor and
located in the centre of the wind-
screen behind the interior mirror;
the associated functions would no
longer be controlled. EXTERIOR SIDE LIGHTERS
These illuminate:
- the zones facing the driver’s and passenger’s doors,
- the zones forward of the door mirrors and rearward of the front
doors.
Switching on
The side lighters come on:
- when you unlock the vehicle or press on the lighting button on
the remote control,
- when you remove the key from the ignition,
- when you open a door,
- when you use the remote control.
Switching off
They are timed to go out automati-
cally.
THE HEADLAMPS
To avoid dazzling other road users,
the height of the halogen bulb head-
lamps must be adjusted according
to the load in the vehicle. To do this,
turn the control, located below the
fascia to the right of the driver, to the
appropriate position:

0. 1 or 2 people in the front seats.

-. 3 people.

1. 4 to 7 people.

-. Intermediate setting.

2. 4 to 7 people + maximum autho-
rised loads.

-. Intermediate setting.

3. Driver + maximum authorised
loads.
Initial setting is position "0".

Page 104 of 330

89
V I S I B I L I T Y
V
AUTOMATIC ADJUSTMENT OF THE DIRECTIONAL HEADLAMPS
In order to avoid causing a nuisance
to other road users, this system cor-
rects the height of the xenon head-
lamps beam automatically and when
stationary, in relation to the load in
the vehicle. If a malfunction oc-
curs, this warning light
is displayed on the
instrument panel, ac-
companied by an au-
dible signal and a message on the
multifunction display.
The system then places your head-
lamps in the lowest position.
Do not touch the xenon headlamps.
Consult a CITROËN dealer.
DIRECTIONAL LIGHTING
When the dipped or main beam
headlamps are on, this function
enables the light beam to follow the
direction of the road.
The use of this function, coupled
with the xenon headlamps only,
considerably improves the quality of
your lighting when cornering.

with directional lighting

without directional lighting Programming
The function is activat-
ed or deactivated via
the multifunction display
confi guration menu.
Operating fault If a malfunction occurs, this
warning light fl ashes on the
instrument panel, accompa-
nied by a message on the
multifunction display.
Consult a CITROËN dealer.
When stationary or moving at very
low speed or when reverse gear is
engaged, the function is inactive.
The status of the function remains
in the memory when the ignition is
switched off.
On vehicles fi tted with daytime run-
ning lights, the function is activated
if the lights stalk is in the "AUTO" or

"Dipped/main beam headlamps"
position. In position "0" , the func-
tion is not activated.

Page 105 of 330

89
V I S I B I L I T Y
V
AUTOMATIC ADJUSTMENT OF THE DIRECTIONAL HEADLAMPS
In order to avoid causing a nuisance
to other road users, this system cor-
rects the height of the xenon head-
lamps beam automatically and when
stationary, in relation to the load in
the vehicle. If a malfunction oc-
curs, this warning light
is displayed on the
instrument panel, ac-
companied by an au-
dible signal and a message on the
multifunction display.
The system then places your head-
lamps in the lowest position.
Do not touch the xenon headlamps.
Consult a CITROËN dealer.
DIRECTIONAL LIGHTING
When the dipped or main beam
headlamps are on, this function
enables the light beam to follow the
direction of the road.
The use of this function, coupled
with the xenon headlamps only,
considerably improves the quality of
your lighting when cornering.

with directional lighting

without directional lighting Programming
The function is activat-
ed or deactivated via
the multifunction display
confi guration menu.
Operating fault If a malfunction occurs, this
warning light fl ashes on the
instrument panel, accompa-
nied by a message on the
multifunction display.
Consult a CITROËN dealer.
When stationary or moving at very
low speed or when reverse gear is
engaged, the function is inactive.
The status of the function remains
in the memory when the ignition is
switched off.
On vehicles fi tted with daytime run-
ning lights, the function is activated
if the lights stalk is in the "AUTO" or

"Dipped/main beam headlamps"
position. In position "0" , the func-
tion is not activated.

Page 107 of 330

91
V I S I B I L I T Y
V
Reverse gear
When reverse gear is engaged, the
rear wiper will come into operation if
the windscreen wipers are operating.
Programming The function is activated
or deactivated via the
multifunction display
confi guration menu.
This function is activated
by default.
Windscreen and headlamp
wash

 Pull the windscreen wiper stalk
towards you. The windscreen
wash then the windscreen wipers
operate for a fi xed period.

If the dipped headlamps are on
,
the headlamp washers operate at
the same time. Automatic windscreen wiping
The windscreen wipers operate au-
tomatically, without any action on the
part of the driver, if rain is detected
(sensor behind the interior mirror),
adapting their speed to the intensity
of the rainfall.
This is controlled manually by the
driver by pushing lever
A to the

"AUTO" position.
It is accompanied by a message on
the multifunction display. The automatic wiping must be
reactivated if the ignition has been
off for more than one minute, by
pushing lever
A downwards.
Operating fault
If an automatic wiping malfunction
occurs, the wipers will operate in in-
termittent mode.
Have it checked by a CITROËN
dealer. Do not cover the rain sensor, linked
with the brightness sensor and
located in the centre of the wind-
screen behind the interior mirror.
Switch off the automatic wiping
when using an automatic car wash.
In winter, it is advisable to wait until
the windscreen is completely clear
of ice before activating the auto-
matic wiping.
Activation
Switching off
This is controlled manually by the
driver by moving lever
A upwards
and returning it to position "0" .
It is accompanied by a message on
the multifunction display.

Page 109 of 330

91
V I S I B I L I T Y
V
Reverse gear
When reverse gear is engaged, the
rear wiper will come into operation if
the windscreen wipers are operating.
Programming The function is activated
or deactivated via the
multifunction display
confi guration menu.
This function is activated
by default.
Windscreen and headlamp
wash

 Pull the windscreen wiper stalk
towards you. The windscreen
wash then the windscreen wipers
operate for a fi xed period.

If the dipped headlamps are on
,
the headlamp washers operate at
the same time. Automatic windscreen wiping
The windscreen wipers operate au-
tomatically, without any action on the
part of the driver, if rain is detected
(sensor behind the interior mirror),
adapting their speed to the intensity
of the rainfall.
This is controlled manually by the
driver by pushing lever
A to the

"AUTO" position.
It is accompanied by a message on
the multifunction display. The automatic wiping must be
reactivated if the ignition has been
off for more than one minute, by
pushing lever
A downwards.
Operating fault
If an automatic wiping malfunction
occurs, the wipers will operate in in-
termittent mode.
Have it checked by a CITROËN
dealer. Do not cover the rain sensor, linked
with the brightness sensor and
located in the centre of the wind-
screen behind the interior mirror.
Switch off the automatic wiping
when using an automatic car wash.
In winter, it is advisable to wait until
the windscreen is completely clear
of ice before activating the auto-
matic wiping.
Activation
Switching off
This is controlled manually by the
driver by moving lever
A upwards
and returning it to position "0" .
It is accompanied by a message on
the multifunction display.

Page 194 of 330

160
X
C H E C K S
PETROL ENGINES
They allow you access for checking the level of the various fl uids and for replacing certain components.

1. Screenwash and headlamp
wash reservoir.

2. Coolant reservoir.
3. Brake fl uid reservoir.

4. Battery/Fuses.

5. Fuse box.
6. Dipstick.

7. Engine oil fi ller cap.

Page 195 of 330

161
X
C H E C K S * According to engine.
DIESEL ENGINES
They allow you access for checking the level of th e various fl uids, for replacing certain components and for repriming the fuel.

1. Screenwash and headlamp
wash reservoir.

2. Coolant reservoir.

3. Brake fl uid reservoir.

4. Battery/Fuses.
5. Fuse box.

6. Dipstick.

7. Engine oil fi ller cap.

8. Repriming pump * .

9. Degas screw * . As the diesel circuit is pres-
surised, any work on this
circuit is prohibited.

Page 197 of 330

163
X
C H E C K S
Screenwash and headlamp
wash fluid
Fluid specifi cation
For optimum cleaning and to avoid
freezing, this fl uid must not be
topped up or replaced with water.
Reservoir capacities:
- screenwash: approximately 3 litres,
- screenwash and headlamp wash: approximately 6 litres. Diesel additive level
(Diesel engine with particle
emission filter)
A low additive level is indicated by
lighting of the service warning light,
accompanied by an audible warning
and a message on the multifunction
display.
Topping up
This additive must be topped up by
a CITROËN dealer without delay.
Used products
Avoid prolonged contact of
used oil or fl uids with the
skin.
Most of these fl uids are harmful to
health or indeed very corrosive.
Do not discard used oil or
fl uids into sewers or onto
the ground.
Empty used oil into the containers
provided for this purpose in the
CITROËN network.
In the case of vehicles fi tted
with headlamp washers, the
minimum level of this fl uid is
indicated by an audible signal
and a message on the multifunction
display.
Top up the level when you stop the
vehicle.

Page 208 of 330

173
XI
P R A C T I C A L I N F O R M A T I O N
CHANGING A BULB
Operating procedure for replacing a
faulty bulb with a new bulb without
the use of any tools.
Headlamps
Model with halogen headlamps

1. Dipped beams (H7 - 55 W)

2. Main beams (H1 - 55 W)

3. Sidelamps (H6W - 6 W)

4. Direction indicators
(H21 - 21 W) A slight misting may appear on the
internal surface of the headlamp
glass in some climatic conditions
(e.g. low temperature or humi dity);
this disappears after the lamps
have been on for a few minutes.

 Do not touch the bulb di-
rectly with your fi ngers,
use lint-free cloths.
The headlamps are fi tted with poly-
carbonate glass with a protective
coating:

 do not clean them using a
dry or abrasive cloth, nor
with a detergent or solvent
product,

 when using a high pressure
washer on persistent marks, do
not direct at the lamps or their
outlines for too long, so as not
to damage their coating and
their seals.
Changing a halogen bulb should
only be done after the headlamp
has been switched off for a few
minutes (risk of serious burns).
It is imperative to use only anti-
ultraviolet (UV) type bulbs in order
not to damage the headlamp. Changing dipped beam
headlamps

 Remove the rubber plug.

 Rotate the bulb-holder a quarter
turn anti-clockwise and remove it
from its housing.

 Replace the faulty bulb.

 Reposition the bulb-holder by
pushing it in, tightening it by a
quarter turn clockwise.

 Put back the rubber plug.

Page 209 of 330

174
XI
P R A C T I C A L I N F O R M A T I O N
Changing main beam headlamps Changing sidelamp s

 Remove the rubber plug.

 Detach the clips by lowering
them on each side of the bulb.


Pull on the bulb-holder to remove it.

 Replace the faulty bulb.

 Push the bulb-holder back into
its housing.

 Reattach the clips.

 Put back the rubber plug.
 Rotate the bulb-holder a quarter
turn anti-clockwise.

 Remove it from its housing.

 Replace the faulty bulb.

 Reposition the bulb-holder.

 Rotate it a quarter turn clockwise
to reposition in its housing. Changing direction indicators
The direction indicator bulb is located
underneath the main beam bulb.

 Remove the rubber plug.


Pull on the bulb-holder to remove it.

 Replace the faulty bulb.

 Reposition the bulb-holder in the
bracket and push it in.

 Put back the rubber plug.

Page:   < prev 1-10 11-20 21-30 next >