engine Citroen C4 PICASSO 2015 2.G Manual Online

Page 288 of 420

286
The batteries contain harmful substances such   as   sulphuric   acid   and   lead.   They m

ust   be   disposed   of   in   accordance
 w

ith   regulations   and   must   not,   in   any
 c

ircumstances,   be   discarded   with   household
 w

aste.
Take
  used   remote   control   batteries   and
 v

ehicle   batteries   to   a   special   collection   point.
Protect your eyes and face before handling   the   battery.
All
  operations   on   the   battery   must   be  
c

arried   out   in   a   well   ventilated   area   and  
a

way   from   naked   flames   and   sources  
o

f   sparks,   so   as   to   avoid   the   risk   of  
e

xplosion   or   fire.
Do
  not   try   to   charge   a   frozen   battery;  
t

he   battery   must   first   be   thawed   out   to  
a

void   the   risk   of   explosion.   If   the   battery  
h

as   been   frozen,   before   charging   have  
i

t   checked   by   a   CITROËN   dealer   or   a  
q

ualified   workshop   who   will   check   that  
t

he   internal   components   have   not   been  
d

amaged   and   the   casing   is   not   cracked,  
w

hich   could   cause   a   leak   of   toxic   and  
c

orrosive   acid.
Do
  not   reverse   the   polarity   and   use   only  
a

  12   V   charger.
Do
  not   disconnect   the   terminals   while  
t

he   engine   is   running.
Do
  not   charge   the   batteries   without  
d

isconnecting   the   terminals   first.
Wash
  your   hands   after wards.
It
 
is
 
advisable
 
to
 
disconnect
 
the
 
battery
 
i

f
 
the
 
vehicle
 
is
 
to
 
be
 
left
 
unused
 
for
 
m

ore
 
than
 
one
 
month.
do n
ot push the vehicle to start the
engine
  if   you   have   an   electronic   or  
a

utomatic   gearbox.Charging the battery using
a battery charger
F Disconnect   the   battery   from   the   vehicle.
F  F ollow   the   instructions   for   use   provided   by  
t

he   manufacturer   of   the   charger.
F
 
C
onnect   the   battery   starting   with   the  
n

egative   terminal   (-).
F
 
C
heck   that   the   terminals   and   connectors  
a

re   clean.   If   they   are   covered   with   sulphate  
(

whitish   or   greenish   deposit),   remove   them  
a

nd   clean   them.
With
  Stop   &   Start,   the   battery   does   not  
h

ave   to   be   disconnected   for   charging.
Do
 
not
 
apply
 
excessive
 
force
 
on
 
the
 
t

ab
 
as
 
locking
 
will
 
not
 
be
 
possible
 
if
 
the
 
c

lamp
 
is
 
not
 
positioned
 
correctly;
 
start
 
t

he
 
procedure
 
again.
Disconnecting the (+) cable
F Raise   the   locking   tab   D fully to release the
cable t erminal c lamp E.
Reconnecting the (+) cable
F Position   the   open   clamp   E of the cable on
the   positive   post   (+)   of   the   battery.
F
 
P
ress   vertically   on   the   clamp   E to position
it
  correctly   on   the   battery.
F
 
L
ock   the   clamp   by   spreading   the  
p

ositioning   lug   and   then   lowering   the   tab   D.
Practical information

Page 289 of 420

287
Exiting economy mode
These functions are reactivated automatically next   time   the   vehicle   is   driven.
F

I
n   order   to   restore   the   use   of   these  
f

unctions   immediately,   start   the   engine   and  
l

et   it   run:
-
 
f
or   less   than   ten   minutes,   to   use  
t

he   equipment   for   approximately  
f

ive minutes,
-
 
f
or   more   than   ten   minutes,   to   use   the  
e

quipment   for   up   to   approximately  
t

hirty
 m
inutes.
Let
  the   engine   run   for   the   duration   specified   to  
e

nsure   that   the   battery   charge   is   sufficient.
Do
  not   repeatedly   and   continuously   restart   the  
e

ngine   in   order   to   charge   the   battery.
A
  flat   battery   prevents   the   engine   from   starting  
(

refer   to   the   "Battery"   section).
Load reduction mode
System which manages the use of certain functions   according   to   the   level   of   charge  
r

emaining   in   the   battery.
When
  the   vehicle   is   being   driven,   the   load  
r

eduction   function   temporarily   deactivates  
c

ertain   functions,   such   as   the   air   conditioning,  
t

he   heated   rear   screen...
The
  deactivated   functions   are   reactivated  
a

utomatically   as   soon   as   conditions   permit.
Energy economy mode
Switching to economy mode
A message then appears in the instrument p
anel   screen   indicating   that   the   vehicle   has  
s

witched   to   economy   mode   and   the   active  
f

unctions   are   put   on   standby.
If
  a   telephone   call   is   being   made   at   this   time,  
i

t will   be   maintained   for   around   10   minutes  
w

ith   the   Bluetooth   hands-free   system   of   your  
a

udio system.
System
  which   manages   the   duration   of   use   of  
c

ertain functions to conserve a sufficient level
of   charge   in   the   battery.
After   the   engine   has   stopped,   you   can  
s

till   use   functions   such   as   the   audio   and  
t

elematics   system,   windscreen   wipers,   dipped  
b

eam   headlamps,   courtesy   lamps,   etc.   for  
a

  maximum   combined   duration   of   about  
f

orty
 m
inutes.
7
Practical information

Page 291 of 420

289
Towing the vehicle
The towing eye is installed in the boot under the   floor.
To
  gain   access   to   it:
F

o
pen the boot,
F
 
l
ift   the   floor   and   remove   it,
F
 
r
emove   the   towing   eye   from   its   housing.
General recommendations
Observe the legislation in force in your country.
E nsure   that   the   weight   of   the   towing   vehicle   is   higher   than   that   of   the   towed   vehicle.
The
  driver   must   remain   at   the   wheel   of   the   towed   vehicle   and   must   have   a   valid   driving   licence.
When
  towing   a   vehicle   with   all   four   wheels   on   the   ground,   always   use   an   approved   towing  
a

rm;   rope   and   straps   are   prohibited.
The
  towing   vehicle   must   move   off   gently.
When
  towing   a   vehicle   with   the   engine   off,   there   is   no   longer   any   power   assistance   for  
b

raking   or   steering.
In
  the   following   cases,   you   must   always   call   on   a   professional   recovery   service:
-
 
v
ehicle   broken   down   on   a   motor way   or   fast   road,
-
 
f
our-wheel   drive   vehicle,
-
 
w
hen   it   is   not   possible   to   put   the   gearbox   into   neutral,   unlock   the   steering,   or   release  
t

he   parking   brake,
-
 
t
owing   with   only   two   wheels   on   the   ground,
-
 
w
here   there   is   no   approved   towing   arm   available...
Procedure
 
for
 
having
 
your
 
vehicle
 
towed
 
or
 
for
 
towing
 
another   vehicle   using   the   towing   eye.
Access to the tools
7
Practical information

Page 292 of 420

290
Towing another vehicle
F On  the   rear   bumper,   unclip   the   cover   by  p
ressing   at   the   bottom.
F
 
S
crew   the   towing   eye   in   fully.
F
 
I
nstall   the   towing   bar.
F
 
S
witch   on   the   hazard   warning   lamps   on  
b

oth   vehicles.
F
 
M
ove   off   gently,   drive   slowly   and   for   a   short  
di

stance.
F
 O
n
 
the
 
front
 
bumper,
 
unclip
 
the
 
cover
 
by
 p
ressing
 
on
 
the
 
left.
F
 
S

crew
 
the
 
towing
 
eye
 
in
 
fully.
F
 
I

nstall
 
the
 
towing
 
bar.
F
 
P

lace
 
the
 
gear
 
lever
 
in
 
neutral
 
(position
 
N
on
 
an
 
electronic
 
or
 
automatic
 
gearbox).
Towing your vehicle
Failure to observe this instruction could r esult   in   damage   to   certain   components  
(

braking,   transmission...)   and   the  
a

bsence   of   braking   assistance   the   next  
t

ime   the   engine   is   started.
F
 
U

nlock   the   steering   by   turning   the   key  
i

n
  the   ignition   one   notch   and   release   the  
par

king
 b
rake.
F
 
S

witch   on   the   hazard   warning   lamps   on  
b

oth   vehicles.
F
 
M

ove   off   gently,   drive   slowly   and   for   a   short  
di

stance.
Practical information

Page 296 of 420

294
Driving advice
Distribution of loads
F Distribute  the   load   in   the   trailer   so   that   the h
eaviest   items   are   as   close   as   possible   to t

he   axle   and   the   nose   weight   approaches   the
 m

aximum   permitted   without   exceeding   it.
Air
  density   decreases   with   altitude,   thus  
r

educing   engine   per formance.   Above  
1 0

00 metres,   the   maximum   towed   load   must  
b

e   reduced   by   10 %   for   every   1 000   metres   of  
al

titude.
Side wind
F Take   into   account   the   increased   sensitivity  t
o   side   wind.
Cooling
Towing a trailer on a slope increases the temperature   of   the   coolant.
As
  the   fan   is   electrically   controlled,   its   cooling  
c

apacity   is   not   dependent   on   the   engine   speed.
F
 
T
o   lower   the   engine   speed,   reduce   your  
s

peed.
The
  maximum   towed   load   on   a   long   incline  
d

epends   on   the   gradient   and   the   ambient  
t

emperature.
In
  all   cases,   keep   a   check   on   the   coolant  
t

emperature. F
 
I
f   the   warning   lamp   and   the  
S

TOP
 
warning   lamp   come   on,  
s

top   the   vehicle   and   switch   off  
t

he   engine   as   soon   as   possible.
Braking
Towing a trailer increases the braking distance.
T o   avoid   overheating   of   the   brakes   on   a   long  
m

ountain   type   of   descent,   the   use   of   engine  
b

raking   is   recommended.
Ty r e s
F Check   the   tyre   pressures   of   the   towing  v
ehicle   and   of   the   trailer,   observing   the  
re

commended
 p
ressures.
Lighting
F Check  the   electrical   lighting   and   signalling  o
n   the   trailer.
Refer
 
to
 
the
 
"Technical
 
data"
 
section
 
for
 
details
 
o

f
 
the
 
weights
 
and
 
towed
 
loads
 
which
 
apply
 
to
 
y

our
 
vehicle.
When
 
not
 
towing
 
a
 
trailer,
 
remove
 
the
 
q

uickly-detachable
 
tow
 
ball
 
before
 
d

riving. The
  rear   parking   sensors   will   be  
d

eactivated   automatically   if   a   genuine  
C

ITROËN   towbar   is   used.
Practical information

Page 302 of 420

300
ToTaL & CITRoËn
Partners in performance and
protecting the environment
Innovation in the search for
performance
For over 40 year, the TOTAL Research and Development   departments   have   developed   lubricants  
f

or   CITROËN,   to   match   the   latest   technical   innovations  
o

n   CITROËN   vehicles,   both   for   competition   and   for  
e

veryday   motoring.
For you, this is an assurance that you will obtain the
best
  per formance   from   your   engine.
Optimum protection for
your engine
By having your CITROËN vehicle serviced   with   TOTAL   lubricants,   you   are  
c

ontributing   towards   improving   the   life  
a

nd   per formance   of   your   engine,   while  
a

lso   protecting   the   environment.
Checks

Page 303 of 420

301
bonnet
F Open  the   left   hand   front   door.
F  
L
ift   the   safety   catch   and   raise   the   bonnet.F
 U nclip   the   stay   from   its   housing   and   place  i
t   in   the   support   slot   to   hold   the   bonnet  
ope

n.
Opening
F Pull  the   release   lever,   located   at   the   bottom  o
f   the   door   aperture,   towards   you. Before
  doing   anything   under   the  b
onnet, switch off the Stop & Start
system
  to   avoid   any   risk   of   injury  
r

esulting   from   an   automatic   change   to  
S

TART   mode.
The cooling fan may star t after
switching off the engine: take care
with articles and clothing that might
be caught by the fan blades. Do   not   open   the   bonnet   under   very  
wi

ndy
 c
onditions.
The location of the interior bonnet
release   lever   prevents   opening   of   the  
b

onnet   when   the   left   hand   front   door  
i

s   shut.
When   the   engine   is   hot,   handle   the  
e

xterior   safety   catch   and   the   stay   with  
c

are   (risk   of   burns),   using   the   protected  
a

rea.
When   the   bonnet   is   open,   take   care   not  
t

o   damage   the   safety   catch.
be

cause of the presence of electrical
equipment
  under   the   bonnet,   it   is  
r

ecommended   that   exposure   to   water  
(

rain,   washing,   ...)   be   limited.
Closing
F Take  the   stay   out   of   its   support   slot.
F  C lip   the   stay   back   into   its   housing.
F
 
L
ower   the   bonnet   and   release   it   at   the   end  
o

f   its   travel.
F
 
P
ull   on   the   bonnet   to   check   that   it   has  
l

atched   correctly.
8
Checks

Page 304 of 420

302
The various caps and covers allow access for checking   the   levels   of   the   various   fluids   and   for  
r

eplacing   certain   components.
Petrol engines
1. Screenwash  and   headlamp   wash   reservoir.
2. C oolant r eservoir.
3.
 B

rake   fluid   reservoir.
4.
 B

attery   /   Fuses.
5.
 F

usebox.
6.
 A

ir   filter.
7.
 E

ngine   oil   dipstick.
8.
 E

ngine   oil   filler   cap.
Checks

Page 305 of 420

303
The various caps and covers allow access for checking   the   levels   of   the   various   fluids,   for  
r

eplacing   certain   components   and   for   priming  
t

he   fuel   system.
Diesel engines
1. Screenwash   and   headlamp   wash   reservoir.
2. C oolant r eservoir.
3.
 B

rake   fluid   reservoir.
4.
 B

attery   /   Fuses.
5.
 F

usebox.
6.
 A

ir   filter.
7.
 E

ngine   oil   dipstick.
8.
 E

ngine   oil   filler   cap.
9.
 P

riming
 pu
mp*.
*
  According   to   engine.
8
Checks

Page 306 of 420

304
Fuel
Capacity of the tank: approximately 57 litres (petrol) or 55 litres (Diesel).
Low fuel levelRefuelling
When the low fuel level is reached, t
his   warning   lamp   comes   on   in   the  
i

nstrument   panel,   accompanied   by   an  
a

udible   warning   and   a   message   and  
t

he   last   bar   of   the   fuel   gauge   comes  
o

n   in   orange.
F
 
T
ake   care   to   select   the   pump   that   delivers  
t

he   correct   type   of   fuel   for   your   vehicle.
F
 
I
ntroduce   the   nozzle   so   as   to   push   in   the  
m

etal   non-return   flap   A.
F
 
M
ake   sure   that   the   nozzle   is   pushed   in   as  
f

ar   as   possible   before   starting   to   refuel  
(risk
  of   blowback).
F
 
M
aintain   this   position   throughout   the  
r

efuelling
 ope
ration.
F
 
P
ush   the   fuel   flap   to   close   it.
If you are filling your tank to the top, do
not persist after the 3rd cut- off; this could
cause malfunctions.
A
  label   on   the   inside   of   the   fuel   filler   flap  
r

eminds   you   of   the   type   of   fuel   to   use,  
d

epending   on   your   engine   type.
Additions
  of   fuel   must   be   of   at   least   5   litres   to  
b

e   registered   by   the   fuel   gauge.
When
 
it
 
first   comes   on,   about 6 litres of fuel
remain
 
in
 
the   tank.
Until
 
sufficient   fuel   has   been   added,   this  
w

arning
 
lamp   appears   every   time   the   ignition  
i

s
 
switched   on,   accompanied   by   an   audible  
w

arning
 
and   a   message.   This   audible   warning  
a

nd
 
message   are   repeated   with   increasing  
f

requency
  as   the   fuel   level   drops   towards   "0 ".
Refuel
 
as
  soon   as   possible   to   avoid   running  
o

ut. Opening
  the   filler   flap   may   result   in   an   inrush   of  
a

ir.   This   is   entirely   normal   and   results   from   the  
s

ealing   of   the   fuel   system.
F
 
W
ith   the   vehicle   unlocked,   press   the   rear  
e

dge   of   the   flap   to   open   it   (the   filler   cap   is   a  
p

art   of   it).
With Stop & Start, never refuel with the
system
  in   STOP   mode;   you   must   switch  
o

ff
 
the   ignition   with   the   START/STOP  
b

utton.
Checks

Page:   < prev 1-10 ... 41-50 51-60 61-70 71-80 81-90 91-100 101-110 111-120 121-130 ... 130 next >