Citroen C5 DAG 2008.5 (RD/TD) / 2.G Owner's Manual

178
11
P R A C T I C A L I N F O R M A T I O N
CHANGING A FUSE
Operating procedure for replacing a
faulty fuse with a new fuse to rectify a
failure of the corresponding function.
The 2 fuseboxes are located below
the dashboard and under the bonnet.
Replacing a fuse
Before replacing a fuse, you should
ascertain the cause of the fault and
have it remedied. The numbers of
the fuses are indicated on the fuse-
box.
Replace the fuse that has blown
with one of the same rating (same
colour).
Use the special pliers 1 placed on
the fl ap close to the fuseboxes. The
fl ap also has spare fuses available.

Good Bad

Pliers 1 Fuses under the dashboard
Access to the fuses

 open the storage box to its stop-
ping point then pull fi rmly on it
horizontally,

 remove the trim by pulling sharp-
ly on the bottom.
Fusebox C
Fusebox
A
Replacement fuses andpliers 1
When refi tting the storage box, ob-
serve the following advice:
- With the storage box horizontal,
refi t the bottom ensuring that the
lower cut-outs are in line with the
pins.
- Give a sharp push to the front.
- Close the storage box, ensuring that the springs located behind
pass over the top.
Fusebox B

179
11
P R A C T I C A L I N F O R M A T I O N
FUSEBOX A Table of fuses

Fuse N° Rating
Function

G29 - -

G30 5 A Heated rear view mirrors

G31 5 A Rain and brightness sensor

G32 5 A Seat belt not fastened warning lamps

G33 5 A Electrochrome rear view mirrors

G34 20 A Sunroof (saloon)

G35 5 A Passenger door lighting - passenger rear view mirror adjustment

G36 30 A Electric tailgate (Tourer)

G37 20 A Heated front seats

G38 30 A Driver’s electric seat

G39 30 A Passenger’s electric seat - HIFI amplifi er

G40 3 A Trailer relay unit supply
FUSEBOX B

Fuse N° Rating
Function

G36
15 A 6 speed automatic gearbox

5 A 4 speed automatic gearbox

G37 10 A Daytime-running lamps - Diagnostic socket

G38 3 A ESP

G39 10 A Hydraulic suspension

G40 3 A STOP switch

180
11
P R A C T I C A L I N F O R M A T I O N
FUSEBOX C

Fuse N° Rating
Function

F1 15 A Rear screen wipe (Tourer)

F2 30 A Locking and deadlocking relay

F3 5 A Airbags

F4 10 A Automatic gearbox - additional heater unit (Diesel) - electrochro me rear view mirrors

F5 30 A Front window - sun roof - passenger door lighting - passenger re ar view mirror adjustment

F6 30 A Rear window

F7 5 A Vanity mirror lighting - Glove box lighting - interior lamps - t orch (Tourer)

F8 20 A Radio - CD changer - Controls at the steering wheel - Displa
y - Defl ation detection - Electric
boot ECU

F9 30 A Cigar-lighter - front 12 V socket

F10 15 A Alarm - Controls on the steering wheel, signalling and screen wipe controls

F11 15 A Low current anti-theft switch

F12 15 A Driver’s electric seat - instrument panel - seat b
elt not fastened warning lamps -air conditioning
controls

F13 5 A Engine relay unit - Hydraulic suspension pump cut-off relay - airba g ECU supply

F14 15 A
Rain and brightness sensor - parking assistance - passenger’s electric seat - trailer relay
unit - HIFI amplifi er ECU - Hands-free kit - Lane Departure Warn ing System

F15 30 A Locking and deadlocking relay

F17 40 A Heated rear screen - exterior heated rear view mirrors

FSH SHUNT PARK SHUNT

181
11
P R A C T I C A L I N F O R M A T I O N
Fuses under the bonnet

After a repair, take care to re-
close the cover.

Any repairs on the MAXI fuses
(that give additional protection),
located in the fuseboxes, must
be left to a CITROËN dealer.
Access to the fuses

 Undo each screw by a 1/4 turn. Table of fuses

Fuse N° Rating Function

F1 20 A Engine control unit

F2 15 A Horn

F3 10 A Screen wash pump

F4 10 A Headlamp wash pump

F5 15 A Starter

F6 10 A Air fl ow meter - Directional headlamps -
Diagnostic socket

F7 10 A Automatic gearbox lever lock - Power steering

F8 25 A Starter

F9 10 A Clutch switch - Stop switch

F10 30 A Starter

F11 40 A Air conditioning blower

F12 30 A Wipers

F13 40 A BSI supply (ignition on)

F14 30 A -

F15 10 A Right-hand main beam

F16 10 A Left-hand main beam

F17 15 A Right-hand dipped beam

F18 15 A Left-hand dipped beam

F19 15 A Starter

F20 10 A Starter

F21 5 A Starter

182
P R A C T I C A L I N F O R M A T I O N
Fuses on the battery
(All engines except V6 HDi)
Fuse N° Rating Function

F6 25 A Rear 12 V socket (max power: 100 W)

F7 15 A Foglamps

F8 20 A Additional burner (Diesel)

F9 30 A Electric parking brake
Access to the fuses

 detach and remove the cover,

 change the fuse. Table of fuses
Your vehicle’s electrical
system is designed to oper-
ate with either standard or
optional equipment.
Before installing electrical equip-
ment or accessories on your vehi-
cle, consult a CITROËN dealer.
CITROËN declines all responsibil-
ity for the consequences and costs
that are caused by faults or repairs
on your vehicle resulting from the in-
stallation of accessories that are not
supplied and/or not recommended
by CITROËN and not installed in
conformity with its requirements,
particularly when the total consump-
tion of additional devices exceeds
10 milliamperes.
The Maxi fuses give additional pro-
tection to electrical systems. any
work on them must be carried out
by a CITROËN dealer.

After a repair, take care to re-
close the cover.

If the cover is not correctly po-
sitioned or not properly closed,
this could cause serious prob-
lems on your vehicle. For the
same reason, take care not to
spill any liquid in the fusebox.

183
11
P R A C T I C A L I N F O R M A T I O N
BATTERY
Procedure for charging your battery
when it is fl at or for starting the en-
gine using another battery. Starting using another
battery
Access to the battery V6 HDi engine
The battery is located under the
bonnet.
To gain access to it:

 open the bonnet using the inte-
rior lever, then the exterior lever,

 secure the bonnet strut,

 remove the plastic cover to gain
access to the two terminals,

 unclip the fuse box to remove
the battery, if necessary. The battery is located in the boot un-
der the left-hand wing trim.
To gain access to it:

 open the boot,

 open the fl ap and remove the
battery.
 Lift the pins to remove the front
left headlamp cover (V6 HDi en-
gine).

 Connect the red cable to the posi-
tive terminal (+) of the fl at bat-
tery A , then to the positive terminal
(+) of the slave battery B .

 Connect one end of the green or
black cable to the negative ter-
minal (-) of the slave battery B .
V6 HDi engine: The negative ter- minal (-) is located under the red
cover.

 Connect the other end of the
green or black cable to the earth
point C on the broken down ve-
hicle.

 Operate the starter, let the en-
gine run.

 Wait until the engine returns to
idle and disconnect the cables.

184
P R A C T I C A L I N F O R M A T I O N
Charging the battery using a
battery charger

 Disconnect the battery from the
vehicle.

 Follow the instructions for use
provided by the manufacturer of
the charger.

 Reconnect starting with the neg-
ative terminal (-).

 Check that the terminals and
connectors are clean. If they are
covered with sulphate (whitish or
greenish deposit), remove them
and clean them.
The batteries contain harm-
ful substances such as sul-
phuric acid and lead. They
must be disposed of in accordance
with regulations and must not, in
any circumstances, be discarded
with household waste.
Take used remote control batteries
and vehicle batteries to a special
collection point.
It is advisable to disconnect the
battery if the vehicle is to be left un-
used for more than one month. Do not disconnect the ter-
minals while the engine is
running.
Do not charge the batteries without
disconnecting the terminals fi rst.
Do not touch the clips during the
operation.
Do not lean over the batteries.
Disconnect the cables in the re-
verse order to connection, ensur-
ing that they do not touch.
Before disconnecting the battery
Wait 2 minutes after switching off
the ignition before disconnecting
the battery.
Close the windows and the doors
before disconnecting the battery. Following reconnection of
the battery
Following reconnection of the bat-
tery, switch on the ignition and wait
1 minute before starting to permit in-
itialisation of the electronic systems.
However, if slight diffi culties are en-
countered following this operation,
contact a CITROËN dealer.
Referring to the corresponding sec-
tion, you must yourself reinitialise:
- the remote control key,
- the glass panoramic roof shutter,
- the GPS satellite navigation
system.

185
11
P R A C T I C A L I N F O R M A T I O N
ENERGY ECONOMY MODE
System which manages the duration
of use of certain functions to con-
serve a suffi cient level of charge in
the battery.
After the engine has stopped, you can
still use functions such as the audio
and telematics system, windscreen
wipers, dipped headlamps, courtesy
lights, etc. for a maximum combined
duration of thirty minutes.
Switching to economy mode
Once the thirty minutes are over, a
message appears on the multi-function
display indicating that the vehicle has
switched to economy mode and the
active functions are put on standby.
If the telephone is being used at this
time:
- it will be maintained for 5 minutes with radio-CD hands-free kit,
-
it will be interrupted after 10 minutes with the MyWay audio- navigation
system,
- you can complete your call with the NaviDrive system.
This period may be signifi cantly
reduced if the battery charge is low. Exiting economy mode
These functions are reactivated au-
tomatically next time the vehicle is
driven.

 In order to resume the use of
these functions immediately,
start the engine and let it run for
a few minutes.
The time available will then be dou-
ble the duration for which the engine
was left running. However, this time
will always be between fi ve and thir-
ty minutes.
A fl at battery prevents the
engine from starting (refer
to the corresponding para-
graph).

186
P R A C T I C A L I N F O R M A T I O N
TOWING THE VEHICLE
Procedure for having your vehicle
towed or for towing another vehicle
using a removable towing eye.
Access to the tools
The towing eye is installed in the
jack box placed in the spare wheel.
To gain access to it:

 open the boot,

 raise the fl oor,

 remove the towing eye from the
jack box. Towing your vehicle

 On the front bumper, unclip the
cover by pressing at the top.

 Screw the towing eye in fully.

 Install the towbar.

 Switch on the hazard warning
lights on the towed vehicle.

 Place the gear lever in neutral
(position N on the automatic
gearbox). Towing another vehicle

 On the rear bumper, unclip the
cover by pressing:
- on the right (Saloon),
- at the bottom (Tourer).

 Screw the towing eye in fully.

 Install the towbar.

 Switch on the hazard warning
lights on the towed vehicle.
Failure to observe this special con-
dition could result in damage to
certain braking components and
the absence of braking assistance
the next time the engine is started. When towing with all four wheels on
the ground, always use a towbar.
When towing with only two wheels
on the ground, always use profes-
sional lifting equipment.
When towing with the engine off,
there is no longer any braking or
steering assistance.

187
11
P R A C T I C A L I N F O R M A T I O N
TOWING A TRAILER, A CARAVAN, ETC.
Towbar suited to the attachment of a
trailer or caravan with additional sig-
nalling and lighting.
Your vehicle is primarily designed
for transporting people and luggage,
but it may also be used for towing a
trailer.
We recommend the use of original
CITROËN towbars and their har-
nesses that have been tested and
approved from the design stage
of your vehicle, and that the fi t-
ting of the towbar is entrusted to a
CITROËN dealer. If the trailer is not fi tted by
a CITROËN dealer, it is
imperative that it is fi tted
using the electrical pre-equipment
installed at the rear of the vehicle,
in accordance with the manufactur-
er's instructions.
Driving with a trailer subjects the
towing vehicle to more signifi cant
stress and its driver must be par-
ticularly careful.
Driving advice
Distribution of loads

 Distribute the load in the trailer
so that the heaviest items are as
close as possible to the axle and
the nose weight approaches the
maximum permitted without ex-
ceeding it.
Air density decreases with altitude,
thus reducing engine performance.
Above 1 000 metres, the maximum
towing load must be reduced by
10 % and so on for every 1 000 me-
tres of altitude.
Refer to the "Technical Data" section
for details of the weights and towing
loads which apply to your vehicle.
Side wind

 Take into account the increased
sensitivity to side wind. Cooling
Towing a trailer on a slope increases
the temperature of the coolant.
As the fan is electrically controlled,
its cooling capacity is not dependent
on the engine speed.

 To lower the engine speed, re-
duce your speed.
The maximum towing load on a long
slope depends on the gradient and
the outside temperature.
In all cases, pay attention to the
coolant temperature.

 If the warning light and
the STOP warning light
come on, stop the vehicle
and switch off the engine
as soon as possible.
Braking
Towing a trailer increases the brak-
ing distance.
Tyres

 Check the tyre pressures of the
towing vehicle and of the trailer,
observing the recommended
pressures.
Lights

 Check the electrical signalling on
the trailer.
The rear parking assistance will
be deactivated automatically if an
original CITROËN towbar is used.