DACIA SOLENZA 2004 Repair Manual

59
SECURITY ELEMENTS
59 - 1
F ront safety belts
1
4
3 2
TIGHTENING MOMENTS(daNm)
Fr
ont safety belt attachment screw 2.7
DISMOUNTING
Di smount:
-front/r ear door gasket (in the
contact area w ith the middle pillar
covering); -attachment scre ws (1) and (2) of
th e front safe t y be l t t o the uppe r pa rt,
conse quently, to th e lowe r part , on the
middle pillar lining; -
middle pillar c overing (see chapter
71); -attachment screw (3) of the safety belt
retriever on the middle pillar l ining. Dismount t he a ttachment scre w (4) of the
saf ety belt lock on the tunnel.
REMOUNTING
Perform t he di smounting operations in the
reverse order, taking into considera tion the
following: -retriever gui ding on t he centeri ng part
welded on the pillar. -the require d t ighte ni ng mome nt of
front the safety belts attachment screws is of
2,7 daNm.
vnx.su

SECURITY ELEMENTS
59
59 - 2
Rear safety belts
4
3 2
132 1
4
TIGHTENING MOMENTS(daNm)
Rear safety belt attachment scre w 2.7
DISMOUNTING
Di
smount t he t wo attachment screws of
the bench backre st. Sw ing over the bench backrest.
Di smount:
-r ear plate and its supports (see
chapter 74);
-belt attachment screws ( 2) and (3) o n
the side fra me lining. P
lace back t he bench backrest i n normal
position.
Sw ing over its supports the bench seat.
Dism oun t t he re a r b e lt attachment
screws ( 4) on the central floor.
REMOUNTING
Perform the dismounting operations in
the reverse order. The require d tightening moment of the
rear belt attachment screws is of 2,7 daNm.
vnx.su

61
HEATING
61 - 1
61General
1 – heating radiator
2 – cold/warm air flaps c ontrol
3 – air repartition flaps control
4 – air repartition control cable
5 – air-mixing control cable
a – air inlet
b – windscreen defogging exit
c – dashboard air vents exit
b
a 3 45 2c
1
vnx.su

61
HEATING
61 - 2
Operating principle
AIR TEMPERATURE CONTROL
The knob (A) is controlling the flaps for cold/warm air.
By rotating to the right the ( A) knob, the air temperature is increasing.
Cold air Warm air
The heating radiator is not having any valve and is permanently supplied. The flap controlled
by the cable ( 1) is ensuring the operation of the cold air re-heating system.
AA
1
vnx.su

61
HEATING
61 - 3
AIR REPARTITION CONTROL
The knob
(B) is controllin g air repartitio n flaps
(1).
Position
Ai rflow is di rected t owards the dashboard
side air vents.
Each air vent has three adjustments: - open or closed;
- upward or downward directed
- left or right directed
Position
Airflow is directed towards all dashboard air
vents and towards passengers legs.
Position
Airflow is directed towards passengers legs.
Op erating principle
Position
Airflow is distributed between all air vents,
defogging air vents of front side windows,
windscreen defogging air vent and passengers
legs.
Position
For a better e fficiency, the dashboard air
vents are t o be closed. The whole airflow is directed towards de-
fogging strip and air vents of the front side win-
dows.
Position
Entire cockpit is outside isolated and out-
side air penetration is not allowed, climate con-
trol blower operation being stopped.
AIR QUANTITY CONTROL
The airflow ra te cycled in the cockpit is
settled by the (C) knob position, corresponding
to the four speeds of the climate control blower.
The more speed step is bigger the more airflow
is bigger.
REMARK
For a better efficiency of the windscreen
defrosting or defogging, t he (C) knob m ust
be placed on the last position.
In order to stop the climate control blower
operation, rotate the knob on “ 0” position.
B
1
B
C
vnx.su

61
HEATING
61 - 4
Climate control unit
DISMOUNTING
Disconnect the battery.
Dismount :
- climate control box protector;
- climate control box gasket
- gas purge vessel;
- engine air filter.
Detach from clips the front wiring from the
central part of the climate control box.
Dismoun t, then:
- attachment screws of the climate con-
trol unit on the climate control box. - attachment screws of the central part
of the climate control box.
Disconnect and release the climate control
unit from the climate control box.
REMOU NT I NG
Perform the dismounting operations in the
reverse order. Tighten t he attachment screws of the c li-
mate control unit on the climate control box, in
the sequence shown in drawing (1,2,3 ).
The required tightening moment of the at-
tachment screws of climate control unit on the
climate control box is of 0,6 daNm. Connector
2
3 1
Pin Denomination 3 Blower control speed 1
4 Blower control speed 2
5 Blower control speed 3
12 Blower control speed 4
13 Blower control speed 4
14 Mass
15 Mass
15 12
5
3
vnx.su

61
HEATING
61 - 5
123
Ve
ntilation-climate control air distributor (RACV)
DISMOUNTIN G
Disconnect the battery.
Dismount :
- dashboard (see chapter 57 “dash-
board”);
- central console;
- electric windows control connectors;
- front pillars coverings;
- driving post cross beam;
- climate control box protector;
- gas purge vessel;
- climate control box gasket;
- engine air filter;
- climate control box central part from
the eight attachment screws;
- attachment screws of the climate c on-
trol unit and release the climate control blower
after disconnecting it.
- RACV attachment screws (1) on the
climate control box.
Clamp t he two hoses from the heating ra-
diator by means of the MOT 453 device.
Disconnect then the fast couplings from the
RACV heating radiator, recovering the c ool-
ing fluid. Dismou nt then:
- acoustic plate ( 2);
- mixing a nd distribution fl aps control
cables attached on RACV. Release RACV (3).
REMOU NT I NG
Perform the dismounting operations in the
reverse order. Fill up the cooling fluid and perform the cool-
ing circuit purging (see chapter 19 “ Filling –
Purging cooling circuit”).
Check :
- good operation of the flaps cables;
- good attachment of t he air ducts.
The require d tightening moment of t he
RACV attachment screws (1) on the climate
control box is of 0,6 daNm.
vnx.su

61
HEATING
61 - 6
Disconnect the battery.
Dismoun
t the distributor of ventilation air con-
ditioning (RACV) position (2) by recovering the
cooling fluid (see R.A.C.V. Dismounting- Re-
mounting). Dismount the attachment screw of the heating
radiator (1 ) and after detaching from clips release
it.
H eating radiator
REMOU NT I NG
Perform the dismounting operations in the
reverse order Fill up the recovered fluid and restore the
fluid level after purging.
REMARK :
The self-adhesive gaskets (3), (4) and (5)
are to be obligatory replaced with new
ones.
vnx.su

61
HEATING
61 - 7
Control panel
DISMOUNTING
Disconnect the battery.
Dismount :
- ashtray ( B);
- front doors electric windows switches
(C). - gearbox lever c over ( D);
Dismount the two screws (A) located in the
lower part of the control panel on the lower
dashboard. Climate control panel is pushed towards
vehicle front part and swing over until it i s re-
leased from supports ( 1) and (2).
CB
A Dismount the two control cables (distribu-
tion and mixing).
Connectors
Connector (6)
Pin Denomination
A1 Control + blower speed 4
A2 Control + blower speed 4
A4 Supply + after contact
A5 Supply + after contact
B1 Control + blower speed 3
B4 Control + blower speed 2
B5 Control + blower speed 1
Disconnect the connector ( 6).
2
1
3
D
1
A
B5
vnx.su

61
HEATING
61 - 8
Connector (3)
Pin Denomination 1Free
2Free
3Free
4Free
5Free
6Free
7+ parking lights
8Free
9 Mass
10 Free
11 F r e e
12 Free
13 Free
14 Free
15 Free
Di sconnect the connector ( 3), carefully push the lever ( 4) and rotate the lever (5) in the
direction of ( E) a rrow.
REMOU NT I NG
Perform the dismounting operations in the reverse order.
Check the operation of the control panel.
5
E
1 15
4
Control panel
vnx.su