DACIA SOLENZA 2004 Repair Manual
SOLENZA 2004
DACIA
DACIA
https://www.carmanualsonline.info/img/8/56875/w960_56875-0.png
DACIA SOLENZA 2004 Repair Manual
Trending: remote start, mileage, tire type, fog light bulb, fuse, air suspension, service
Page 431 of 891
54
54 - 2
GLASSES
Each time a windscreen is mounted, ensure the uniform setting of the whole assembly on the
carriage body by tapping several times with a rubber hammer, on the edge of the glass frame.
REMARK:
Do not tap the glass on corners and on the two vertical sides. Take care that both
spacers are correctly positioned.
After the windscreen mounting check out carefully the uniformity of the whole assembly and
then its waterproofing by splashing with a jet of water.
Windscreen glass
vnx.su
Page 432 of 891
54
54 - 3
GLASSES
REPLACEMENT HATCHBACKGLASS
Disconnect: - battery
-supply and m ass connectors of the
hatchback defrosting. Remove the glass together with the gas-
ket, by pushing it from the inside of the ve -
hicle. Clean the gasket and place the glass in its
new gasket.
Hatchbac k g lass
WINDSCREEN AND HATCHBACK
GLASS REPLACEMENT
The replacement of these glasses is per-
formed in case t hey are broken, when they
are not according to the required overall di -
mensions or when they have manufacturing
defects (image distortions, cracks, etc). The mounting of the hatchback glass – gas-
ket assembly , is performed in the same way with
the windscreen mounting.
vnx.su
Page 433 of 891
54
54 - 4
GLASSES
1
DISMOUNTING
Dismount :
- front door panel (see chapter 72);
- front door deflector panel;
- inner and outside wiper;
Bring the glass up to the P=85 mm position.
Dismount the attachment screws of the glass support on the regulator glider and then remove
the glass (1) together with the glass support.
Release t he glass from its support.
Front do or glasses
REMOU NT I NG
Perform in the reverse order the dismounting operations, observing the followings:
- place the glass, previously fitted in the glass support, and attach it on the glider.
- check the regulator operation by lifting and lowering the glass.
- check t he continuity of t he Romtix 1502 P sealant material layer, on which t he front
door deflector panel is stacked.
vnx.su
Page 434 of 891

54
54 - 5
GLASSES
Rear door glasses
3
421
DISMOUNTIN
G
Dismount :
-r ear door panel (see c hapter 72);
-r ear door deflector panel;
- glass outside wiper by means of a screwdriver.
Lower the glass in the minimal position, so that through the technological opening, the screws
attaching the glass support on the regulator glider, to be dismounted.
Remove the glass (1 ) together with the glass support.
Release t he glass from its support.
Dismo unt :
- screws (3) attaching the glider to the glass.
- the fix glass.
R EMOU NT I NG
Perform the dismounting operations in the reverse order, observing the followings:
- position in the glass support, the fix glass, on which the glass gasket has been previously
mounted. -place the glass in the frame ( on which the glass support has been previously mounted)
and fix it on the glider by means of the screws; -check the regulator operation by glass lifting and lowering.
- check the positioning and then the waterproofing in the fix glass area.
- in case water penetration is occurring in the fix glass area, pierce the water draining holes
and put sealing material on the fix glass gasket, using Terodicht Scwartz sealant material.
vnx.su
Page 435 of 891
OUTSIDE PROTECTIONS
55
55 - 1
Front bumper
DISMOUNTIN G
Dismount the front grill.
Lift the vehicle by means of a two-column elevator.
Disconnect the projector lamps connectors.
Dismo unt :
- bumper attachment screws (1) on power train frame;
- bumper attachment screws (2) on the front anti-shock cross member;
- bumper attachment screws (3) on the front wing attachment side supports.
Release the bumper from its sustaining clips (4)
REMOU NT I NG
Perform the dismounting operations in the reverse order.
Front bumper attachment screws are to be tighten to the required moment of 4 Nm, and the
fairing attachment screws to the required moment of 1.4 Nm.
4
1 2
3
vnx.su
Page 436 of 891
OUTSIDE PROTECTIONS
55
55 - 2
Rear bumper
DISMOUNTIN G
Disconnect the rear lamps connectors.
Dismount :
-r ear lamps;
- attachment screws (2) of the rear bumper (1) on the rear lower plate;
- attachment screws (5) of the rear bumper on the rear wheels passage;
- attachment screws (3) of the rear bumper (lower part) on the rear extreme cross member;
- attachment screws (4) of the rear bumper on the side panels.
D etach the rear bumper.
REMOU NT I NG
Perform the dismounting operations in the reverse order.
Required tightening moment of the rear bumper attachment screws on passage is of 1,4 Nm .
The other rear bumper attachment screws are to be tighten to the required moment of 6 Nm.
1
4
5 32
vnx.su
Page 437 of 891
OUTSIDE PROTECTIONS
55
55 - 3
Hatchback handle ornament
DISMOUNTING
Dismoun t the attachment nuts (2) of the hatchback handle ornament (1) on the outside hatchback
panel.
Release the hatchback handle ornament.
REMOU NT I NG
Perform the dismounting operations in the reverse order.
2
1
vnx.su
Page 438 of 891
OUTSIDE PROTECTIONS
55
55 - 4
Front grill
DISMOUNTIN G
Dismount :
- front grill (2) attachment screws (1) on the radiator upper cross beam;
-F ront grill attachment screw (3) on the radiator upper cross beam.
REMOU NT I NG
Perform the dismounting operations in the reverse order.
3
2
1
vnx.su
Page 439 of 891
OUTSIDE PROTECTIONS
55
55 - 5
Aileron
DISMOUNTIN G
Dismount the attachment screws (2) of the aileron (1) on the hatchback outside panel.
Release the aileron.
REMOU NT I NG
Perform the dismounting operations in the reverse order.
Check the integrity of the gaskets ( 3) and (4), if damaged, replace them.
The attachment screws ( 2) are to be tighten to the required moment of 5 Nm.
1
4
2
3
vnx.su
Page 440 of 891
OUTSIDE PROTECTIONS
55
55 - 6
Side ornaments
DISMOUNTIN G
Side ornaments of the front panels, doors and wings, are to dismounted by unstuck.
Carefully clean the place from where ornaments have been detached, with an adequate sol-
vent and wipe with soft and dry cloth.
R EMOU NT I NG
Position the centering spurs (1) of the side ornaments in t he wholes provided in t he doors
panels and attach them by sticking.
The side ornaments for wings are to be aligned with the side ornaments of the panels and are
to be attached by easy and uniform pressing.
1
vnx.su
Trending: start stop button, headlight bulb, weight, low oil pressure, fuel filter location, door lock, oil type