DACIA SOLENZA 2004 Repair Manual

57
57 - 3
INSIDE ACCESSORIES
Dismo unt :
-t wo side attachment screws (8) of the
upper part dashboard by means of a wrench T
20(“L” shape);
-screws (9) attaching the upper part
dashboard with the l ower part on the driving
post cross member, by means of a screwdriver
with T20 head. Detach from clips placed in points (10) the
upper part dashboard. Sw ing over the windscreen the upper part
dashboard and de tach from c lips poi nts (11)
of the windscreen lower cross beam. Detach from clips the radio from i ts sup-
port.
Disconnect the connectors and the ra dio
antenna (for the vehicle provided with radio-
cassettes player). Disconnect the central l ocking connector
(for the vehicle provided with central locking).
Take out the upper part dashboard from the
cockpit.
REMARK :
Dismounting of the upper part dash-
board, does not imply steering wheel dis-
mounting.
Disconn ect the anti-star ting bushing connec-
tor.
Detach from clips the anti-starting bushing
(12).
8
8
10
9
11
12
13
13 Dismount
the attachme nt screws (13) of the
instrument panel and disconnect the four con-
nectors.
Dashboard
vnx.su

57
57 - 4
INSIDE ACCESSORIES
19 20
17 16
15
18
Remove the access cover of the fuse box.
Di
smount the three a ttachment screws (14)
of the fuse box.
21
14
Remove the access cover to the fuse box.
Swing over the little caps from the dashboard
lower part and dismount the attachment screws
(15) on the driving post cross member.
Dismou nt :
- attachment scre ws (16) of the climate
maintenance p anel on the lower part dashboard;
- attachment screw (17) of the lower part
dashboard on the vent-AC distributor (RACV);
- attachment screws (18) of the lower part
dashboard on the driving post cross member;
-upper attachment screws (19) of the
lower part dashboard on the driving post cross
member.
Extract :- headlamps adjustment knob;
-cigarette lighter.
Detach from clips the connectors: - hazard;
-r
ear window defrosting.
Disconnect the connectors:
- cigarette lighter;
-r ear window defrosting.
Di smount the attachment nut (21) of the
headlamps adjustment control.
Disconnect the connectors:
- hazard;
- climate maintenance control.
D etach from clips the l eft a nd right side
aeration ducts.
Take out t he dashboard from cockpit.
Dashboard
vnx.su

57
57 - 5
INSIDE ACCESSORIES
REMOU NT I NG
Perform the dismounting operations in the reverse order, taking into consideration the follow-
ing recommendations:
-ensure that steering is at middle point (wheels are in a direct line);
- mounting of the lower part dashboard is to be performed by guiding it on a centering part
placed on the driving post cross beam; -steering wheel must freely enter in grooves;
- check the operation of the dashboard instruments and switches.
AT T E N T I O N :
After each steering wheel dismounting, its attachment screw is to be replaced, ob-
s erving the required tightening moment of 4.4 daNm.
Dashboard
vnx.su

57
57 - 6
INSIDE ACCESSORIES
Dashboard
Airbag
I mportant!
Before reconnecting the driver’s airbag connector, it is necessary to apply a checking
procedure of the system:
- Check if ai rbag indicator from the instrument panel is on, when the contact is set
on.
- Connect the igniter to the airbag connector (to the wiring) and check if the airbag
indicator is off. - Set the contact off, connect the airbag connector instead of the inert igniter and
attach the airbag on the steering wheel (requiret tightening moment is 0.65 daNm). After remounting, perform the system checking by means of the CLIP tester.
If everything is correct, unblock the UCE airbag (see chapter 88 “Unblocking UCE
airbag”). If is not correct, see chapter “Diagnostic”.
- Check if t he airbag i ndicator from the instrument panel is on for 3 seconds from
setting the cont act on, t hen it is off and i s remaini ng off.
AT T E N T I ON!
No n-observing of prevision prescriptions may cause un abnormal operation of the
sy stem, leading to the airbag undesirable starting.
vnx.su

57
57 - 7
INSIDE ACCESSORIES
DISMOUNTIN G
Upper attachment:
By means of a screwdriver, detach from clips the limiting wire for documents compartment
door’s opening from lower part dashboard.
Lower attachment:
P ush the plastic pin to the right side of driving post (in the arrow direction) and release the
documents compartment door from the lower part dashboard.
REMOU NT I NG
Perform the dismounting operations in the reverse or der.
Documents compartment door
vnx.su

57
57 - 8
INSIDE ACCESSORIES
Inside rear view mirror
DISMOUNTIN G
Dismounting of the interior rear view mirror ( 1) is to be performed by its depressing from the
support (2 ) in the direction of the arrow shown in the drawing.
The rear view m irror support ( 2) is stacked on windshield (3 ) .
REMOU NT I NG
Perform the dismounting operations in the reverse order.
vnx.su

57
57 - 9
INSIDE ACCESSORIES
Sun vi sors
DISMOUNTIN G
Dismount the sun visor (2) attachment screw (1).
Extract the sun visor from the hook ( 3).
REMOU NT I NG
Perform the dismounting operations in the reverse order.
vnx.su

57
57 - 10
INSIDE ACCESSORIES
Central c onsole
DISMOUNTIN G
Disconnect the battery.
Extract the ashtray ( 1) from its place.
Remove the gearbox lever covering ( 2) f rom
the central console.
Dismo unt :
- attachment screw ( 3) of the centra l
console on the tunnel; - attachment screw ( 4) of the centra l
console on the gearbox lever support. Detach the central console from the climate
maintenance- ve ntilating distri butor clips
(RACV) from points ( 5).
Swing over the diagnostic socket c ap and
push inside the console.
Disconnect the window lifting switch
connector (for vehicles equipped with electric
windows). Detach from clips the window-liftin g switch
and release the central console.
R EMOU NT I NG
Perform the dismountin g operations in the
reverse order. Che c k t he c orr e c t ope r a t i on o f t he
switches of the front electric windows.
vnx.su

57
57 - 11
INSIDE ACCESSORIES
Handb rake case
DISMOUNTIN G
Through the cutting out existent in the cock-
pit carpet in the handbrake lever, dismount the
attachment screw (1) of the handbrake case in
front part, on the tunnel.
Move towards front the seats.
Dismo unt :
- bench seat ( see c hapter 75); - attachmen
t screws of the front safety belts
at lower part; - attachment screws of the locks on the tun-
nel;
Detach from clips the carpet and roll it towards
front part.
Dismount the attachment screw ( 2) of the
handbrake case on the tunnel, in the rear part. Release the handbrake c ase.
REMOU NT I NG
Perform the dismounting operations in the re-
verse order. The safety belts screws are to be tighten to the
required moment of 2,7 daNm.
vnx.su

57
57 - 12
INSIDE ACCESSORIES
Tu r n i n g handle
DISMOUNTIN G
Dismount the screws from points A attaching the turning handle on the body roof.
Release the turning handle.
REMOU NT I NG
Perform the dismounting operations in the reverse order.
vnx.su