heater DAEWOO MATIZ 2003 Service Repair Manual

1D – 2 ENGINE COOLING
DAEWOO M-150 BL2
DESCRIPTION AND OPERATION
GENERAL DESCRIPTION
The cooling system maintains the engine temperature at
an efficient level during all engine operating conditions.
When the engine is cold the cooling system cools the
engine slowly or not at all. This slow cooling of the en-
gine allows the engine to warm up quickly.
The cooling system includes a radiator(a) and cooling
fan(b), a thermostat and housing(c), a coolant pump(d),
a coolant pump drive belt and coolant hose. The timing
belt drives the coolant pump.
All components must function properly in order for the
cooling system to operate. The coolant pump draws the
coolant from the radiator. The coolant then circulates
through water jackets in the engine block and the cylin-
der head, distributor case(e), throttle body(f). When the
coolant reaches the operating temperature of the ther-
mostat, the thermostat opens. The coolant then goes
back to the radiator where it cools.
This system directs some coolant through the hoses to
the heater core(g). This provides for heating and de-
frosting. The surge tank(h) is connected to the radiator
and throttle body to recover the coolant displaced by ex-
pansion from the high temperatures. The surge tank
maintains the correct coolant level.
The cooling system for this vehicle has no radiator cap
and drain cock. The coolant is added to the cooling sys-tem through the surge tank. To drain the cooling system,
disconnect the lower radiator hose and drain the cool-
ant.
RADIATOR
This vehicle has a lightweight tube-and-fin aluminum ra-
diator.
SURGE TANK
The surge tank is a transparent plastic reservoir, similar
to the windshield washer reservoir.
The surge tank is connected to the radiator and throttle
body by a hose. As the vehicle is driven, the engine cool-
ant heats and expands. The portion of the engine cool-
ant displaced by this expansion flows from the radiator
into the surge tank. The air trapped in the radiator is de-
gassed into the surge tank.
When the engine is stops, the engine coolant cools and
contracts. The displaced engine coolant is then drawn
back into the radiator. This keeps the radiator filled with
the coolant to the desired level at all times and increases
the cooling efficiency.
Maintain the coolant level between the MIN and the
MAX marks on the surge tank when the system is cold.
D102D001

ENGINE COOLING 1D–3
DAEWOO M-150 BL2
COOLANT PUMP
The belt-driven centrifugal coolant pump consists of an
impeller, a drive shaft, and a belt pulley.
The impeller is supported by a completely sealed bear-
ing.
The coolant pump is serviced as an assembly and,
therefore, cannot be disassembled.
THERMOSTAT
A wax pellet-type thermostat controls the flow of the en-
gine coolant through the engine cooling system. The
thermostat(i) is mounted in the thermostat housing.
The thermostat stops the flow of the engine coolant from
the engine to the radiator in order to provide faster
warm-up, and to regulate the coolant temperature. The
thermostat remains closed while the engine coolant is
cold, preventing circulation of the engine coolant
through the radiator. At this point, the engine coolant is
allowed to circulate only throughout the heater core to
warm it quickly and evenly.
As the engine warms, the thermostat opens. This allows
the engine coolant to flow through the radiator, where
the heat is dissipated through the radiator. This opening
and closing of the thermostat permits enough engine
coolant to enter the radiator to keep the engine within
proper engine temperature operating limits.
The wax pellet in the thermostat is hermetically sealed in
a metal case(j). The wax element of the thermostat ex-
pands when it is heated and contracts when it is cooled.
As the vehicle is driven and the engine warms, the en-
gine coolant temperature increases. When the engine
coolant reaches a specified temperature, the wax pellet
element in the thermostat expands and exerts pressure
against the metal case, forcing the valve open. This al-
lows the engine coolant to flow through the engine cool-
ing system and cool the engine.
As the wax pellet cools, the contraction allows a spring
to close the valve.
The thermostat begins to open at 82
C (180
F) and is
fully open at 95
C (203
F). The thermostat closes at
80
C (176
F).
D102D002
ELECTRIC COOLING FAN
Caution: Keep hands, tools, and clothing away from
the engine cooling fans to help prevent personal in-
jury. This fan is electric and can turn ON whether or
not the engine is running.
Caution: If a fan blade is bent or damaged in any
way, no attempt should be made to repair or reuse
the damaged part. A bent or damaged fan assembly
should always be replaced with a new one.
The cooling fans are mounted behind the radiator in the
engine compartment. The electric cooling fans increase
the flow of air across the radiator fan and across the
condenser on air conditioner (A/C)-equipped vehicles.
This helps to speed cooling when the vehicle is at idle or
moving at low speeds.
D102D003

ENGINE COOLING 1D–5
DAEWOO M-150 BL2
COMPONENT LOCATOR
COOLANT HOSE AND COMPONENTS
D12D4011
1 Radiator Coolant Return Hose
2 Upper Radiator Hose
3 Not Used
4 Radiator Assembly
5 Lower Radiator Hose
6 Throttle Body Assembly
7 Surge Tank hose
8 Surge Tank
9 Coolant Temperature Sensor
10 Engine Coolant Temperature Sensor11 Surge Tank Return Hose
12 Water Inlet Cap
13 Heater Outlet Hose
14 Heater Inlet Hose
15 Distributor Case
16 Thermostat
17 Thermostat Housing
18 Throttle Body Inlet Hose
19 Throttle Body Outlet Hose
20 Hose Bracket

1D–8 ENGINE COOLING
DAEWOO M-150 BL2
COOLING SYSTEM DIAGNOSIS
Condition Probable Cause Correction
Engine OverheatsA loss of the coolant.Add the coolant.
A weak coolant solution.Confirm that the coolant solution is a
50/50 mixture of ethylene glycol and
water.
Any dirt, any leaves, or any insects
on the front of the radiator.Clean the front of the radiator.
The leakage from the hoses, the
coolant pump, the heater, the
thermostat housing, the radiator, the
heater core, or the head gasket.Replace any damaged components.
A faulty thermostat.Replace a damaged thermostat.
Retarded ignition timing.Perform an ECM code diagnosis.
Confirm the integrity of the timing
belt.
An improperly operating electric
cooling fan.Replace the electric cooling fan.
Plugged or rotted radiator hoses.Replace any damaged radiator
hoses.
A faulty water pump.Replace a faulty water pump.
A faulty surge tank cap.Replace a faulty surge tank cap.
A cracked or plugged cylinder head
or engine block.Repair the damaged cylinder head or
the damaged engine block.
A faulty radiator.Replace a faulty radiator.
Loss of CoolantA leak in the radiator.Replace a damaged radiator.
A leak in the surge tank or the hose.Replace the surge tank or the hose.
Looseness or damage of radiator
hoses, heater hoses, or connections.Reseat the hoses.
Replace the hoses or the clamps.
Leaks in the coolant pump seal.Replace the coolant pump seal.
Leaks in the coolant pump gasket.Replace the coolant pump gasket.
An improper cylinder head torque.Tighten the cylinder head bolts to
specifications.
Replace the cylinder head gasket, if
needed.
Leaks in the intake manifold, cylinder
head gasket, heater core.Repair or replace any components,
as needed to correct the leak.
Engine Fails to Reach
Normal OperatingThermostat to be stuck open or to be
wrong type.Install a new thermostat of the
correct type and heat range.
Temperature or Cool Air
from the HeaterThe coolant level below the MIN
mark on the surge tank.Add sufficient coolant to raise the
fluid to the specified mark on the
surge tank.

1F – 2 ENGINE CONTROLS
DAEWOO M-150 BL2
DTC P0122 Throttle Position Sensor Low
Voltage 1F-76. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
DTC P0123 Throttle Position Sensor High
Voltage 1F-80. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
DTC P0131 Oxygen Sensor Low Voltage 1F-84. . . .
DTC P0132 Oxygen Sensor High Voltage 1F-88. . . .
DTC P0133 Oxygen Sensor No Activity 1F-90. . . . .
DTC P0137 Heated Oxygen Sensor Low
Voltage 1F-94. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
DTC P0138 Heated Oxygen Sensor High
Voltage 1F-98. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
DTC P0140 Heated Oxygen Sensor
No Activity 1F-100. . . . . . . . . . . . . . . . . . . . . . . . . . . .
DTC P0141 Heated Oxygen Sensor
Heater Malfunction 1F-104. . . . . . . . . . . . . . . . . . . .
DTC P0171 Fuel Trim System Too Lean 1F-106. . . .
DTC P0172 Fuel Trim System Too Rich 1F-109. . . .
DTC P1230 Fuel Pump Relay Low Voltage 1F-114.
DTC P1231 Fuel Pump Relay High Voltage 1F-118.
DTC P0261 Injector 1 Low Voltage 1F-122. . . . . . . .
DTC P0262 Injector 1 High Voltage 1F-124. . . . . . . .
DTC P0264 Injector 2 Low Voltage 1F-126. . . . . . . .
DTC P0265 Injector 2 High Voltage 1F-128. . . . . . . .
DTC P0267 Injector 3 Low Voltage 1F-130. . . . . . . .
DTC P0268 Injector 3 High Voltage 1F-132. . . . . . . .
DTC P0300 Multiple Cylinder Misfire 1F-135. . . . . . .
DTC P0300 Multiple Cylinder Misfire 1F-139. . . . . . .
DTC P1320 Crankshaft Segment Period
Segment adaptation At Limit 1F-142. . . . . . . . . . . .
DTC P1321 Crankshaft Segment Period
Tooth Error 1F-144. . . . . . . . . . . . . . . . . . . . . . . . . . .
DTC P0327 Knock Sensor Circuit Fault 1F-146. . . .
DTC P0335 Magnetic Crankshaft Position
Sensor Electrical Error 1F-150. . . . . . . . . . . . . . . . .
DTC P0336 58X Crankshaft Position Sensor
No Plausible Signal 1F-152. . . . . . . . . . . . . . . . . . . .
DTC P0337 58X Crankshaft Position Sensor
No Signal 1F-154. . . . . . . . . . . . . . . . . . . . . . . . . . . .
DTC P0341 Camshaft Position Sensor
Rationality 1F-156. . . . . . . . . . . . . . . . . . . . . . . . . . . .
DTC P0342 Camshaft Position Sensor
No Signal 1F-158. . . . . . . . . . . . . . . . . . . . . . . . . . . .
DTC P0351 Ignition Signal Coil A Fault 1F-160. . . . .
DTC P0352 Ignition Signal Coil B Fault 1F-162. . . . .
DTC P0353 Ignition Signal Coil C Fault 1F-164. . . . .
DTC P1382 Rough Road Data
Invalid (Non ABS) 1F-166. . . . . . . . . . . . . . . . . . . . .
DTC P1382 Rough Road Data Invalid (ABS) 1F-170
DTC P1385 Rough Road Sensor Circuit Fault
(Non ABS) 1F-174. . . . . . . . . . . . . . . . . . . . . . . . . . .
DTC P1385 Rough Road Sensor Circuit Fault
(ABS) 1F-178. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . DTC P0400 Exhaust Gas Recirculation
Out Of Limit 1F-182. . . . . . . . . . . . . . . . . . . . . . . . . .
DTC P1402 Exhaust Gas Recirculation
Blocked 1F-186. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
DTC P1403 Exhaust Gas Recirculation
Valve Failure 1F-188. . . . . . . . . . . . . . . . . . . . . . . . . .
DTC P0404 Exhaust Gas Recirculation
Opened 1F-192. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
DTC P1404 Exhaust Gas Recirculation
Closed 1F-196. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
DTC P0405 EEGR Pintle Position Sensor
Low Voltage 1F-200. . . . . . . . . . . . . . . . . . . . . . . . . .
DTC P0406 EEGR Pintle Position Sensor
High Voltage 1F-204. . . . . . . . . . . . . . . . . . . . . . . . . .
DTC P0420 Catalyst Low Efficiency 1F-208. . . . . . . .
DTC P0444 EVAP Purge Control Circuit
No Signal 1F-210. . . . . . . . . . . . . . . . . . . . . . . . . . . .
DTC P0445 EVAP Purge Control Fault 1F-214. . . . .
DTC P0462 Fuel Level Sensor Low Voltage 1F-218.
DTC P0463 Fuel Level Sensor High Voltage 1F-222
DTC P0480 Low Speed Cooling Fan Relay
Circuit Fauit (Without A/C) 1F-226. . . . . . . . . . . . . .
DTC P0480 Low Speed Cooling Fan Relay
Circuit Fauit (With A/C) 1F-230. . . . . . . . . . . . . . . . .
DTC P0481 High Speed Cooling Fan Relay
Circuit Fauit (Without A/C) 1F-234. . . . . . . . . . . . . .
DTC P0481 High Speed Cooling Fan Relay
Circuit Fauit (With A/C) 1F-238. . . . . . . . . . . . . . . . .
DTC P0501 Vehicle Speed No Signal
(M/T Only) 1F-242. . . . . . . . . . . . . . . . . . . . . . . . . . . .
DTC P1505 Idle Air Control Valve (IACV)
Error 1F-246. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
DTC P1535 Evaporator Temperature Sensor
High Voltage 1F-250. . . . . . . . . . . . . . . . . . . . . . . . . .
DTC P1536 Evaporator Temperature Sensor
Low Voltage 1F-252. . . . . . . . . . . . . . . . . . . . . . . . . .
DTC P1537 A/C Compressor Relay High
Voltage 1F-254. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
DTC P1538 A/C Compressor Relay Low
Voltage 1F-256. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
DTC P0562 System Voltage (Engine Side)
Too Low 1F-258. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
DTC P0563 System Voltage (Engine Side)
Too High 1F-260. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
DTC P0601 Engine Control Module Chechsum
Error 1F-262. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
DTC P0604 Engine Control Module Internal/
External RAM Error 1F-263. . . . . . . . . . . . . . . . . . . .
DTC P0605 Engin Control Module NMVY
Write Error 1F-264. . . . . . . . . . . . . . . . . . . . . . . . . . .
DTC P1610 Main Relay High Voltage 1F-266. . . . . .
DTC P1611 Main Relay Low Voltage 1F-268. . . . . . .

1F–6 ENGINE CONTROLS
DAEWOO M-150 BL2
pors. Fresh air from the air cleaner is supplied to the
crankcase. The fresh air is mixed with blowby gases
which then pass through a vacuum hose into the intake
manifold.
Periodically inspect the hoses and the clamps. Replace
any crankcase ventilation components as required.
A restricted or plugged PCV hose may cause the follow-
ing conditions:

Rough idle

Stalling or low idle speed

Oil leaks

Oil in the air cleaner

Sludge in the engine
A leaking PCV hose may cause the following conditions:

Rough idle

Stalling

High idle speed
ENGINE COOLANT TEMPERATURE
SENSOR
The Engine Coolant Temperature (ECT) sensor is a
thermistor (a resistor which changes value based on
temperature) mounted in the engine coolant stream.
Low coolant temperature produces a high resistance
(100,000 ohms at –40C [–40F]) while high tempera-
ture causes low resistance (70 ohms at 130C [266F]).
The Engine Control Module (ECM) supplies 5 volts to
the ECT sensor through a resistor in the ECM and mea-
sures the change in voltage. The voltage will be high
when the engine is cold and low when the engine is hot.
By measuring the change in voltage, the ECM can de-
termine the coolant temperature. The engine coolant
temperature affects most of the systems that the ECM
controls. A failure in the ECT sensor circuit should set a
Diagnostic Trouble Code (DTC) P0117 or P0118. Re-
member, these DTC indicate a failure in the ECT circuit,
so proper use of the chart will lead either to repairing a
wiring problem or to replacing the sensor to repair a
problem properly.
THROTTLE POSITION SENSOR
The Throttle Position (TP) sensor is a potentiometer
connected to the throttle shaft of the throttle body. The
TP sensor electrical circuit consists of a 5-volt supply
line and a ground line, both provided by the Engine Con-
trol Module (ECM). The ECM calculates the throttle
position by monitoring the voltage on this signal line. The
TP sensor output changes as the accelerator pedal is
moved, changing the throttle valve angle. At a closed
throttle position, the output of the TP sensor is low,
about 0.4–0.8 volt. As the throttle valve opens, the out-
put increases so that, at Wide Open Throttle (WOT), the
output voltage will be about 4.5–5 volts.The ECM can determine fuel delivery based on throttle
valve angle (driver demand). A broken or loose TP sen-
sor can cause intermittent bursts of fuel from the injector
and an unstable idle, because the ECM thinks the
throttle is moving. A problem in any of the TP sensor cir-
cuits should set a Diagnostic Trouble Code (DTC)
P0122 or P0123. Once the DTC is set, the ECM will sub-
stitute a default value for the TP sensor and some ve-
hicle performance will return.
CATALYST MONITOR OXYGEN
SENSORS
Three-way catalytic converters are used to control emis-
sions of hydrocarbons (HC), carbon monoxide (CO),
and oxides of nitrogen (NOx). The catalyst within the
converters promotes a chemical reaction. This reaction
oxidizes the HC and CO present in the exhaust gas and
converts them into harmless water vapor and carbon
dioxide. The catalyst also reduces NOx by converting it
to nitrogen. The ECM can monitor this process using the
oxygen sensor (O2S) and heated oxygen sensor
(HO2S). These sensors produce an output signal which
indicates the amount of oxygen present in the exhaust
gas entering and leaving the three-way converter. This
indicates the catalyst’s ability to efficiently convert ex-
haust gasses. If the catalyst is operating efficiently, the
O2S signals will be more active than the signals pro-
duced by the HO2S. The catalyst monitor sensors oper-
ate the same way as the fuel control sensors. The
sensors’ main function is catalyst monitoring, but they
also have a limited role in fuel control. If a sensor output
indicates a voltage either above or below the 450 mV
bias voltage for an extended period of time, the Engine
Control Module (ECM) will make a slight adjustment to
fuel trim to ensure that fuel delivery is correct for catalyst
monitoring.
A problem with the O2S circuit will set DTC P0131,
P0132, P0133 or P0134 depending on the special condi-
tion. A problem with the HO2S signal will set DTC
P0137, P0138, P0140 or P0141 depending on the spe-
cial condition.
A fault in the heated oxygen sensor (HO2S) heater ele-
ment or its ignition feed or ground will result in lower oxy-
gen sensor response. This may cause incorrect catalyst
monitor diagnostic results.
ELECTRIC EXHAUST GAS
RECIRCULATION VALVE
The Electric Exhaust Gas Recirculation (EEGR) system
is used on engines equipped with an automatic trans-
axle to lower oxides of nitrogen (NOx) emission levels
caused by high combustion temperature. The main ele-
ment of the system is the EEGR valve, controlled electri-
cally by the Engine Control Module (ECM). The EEGR
valve feeds small amounts of exhaust gas into the intake

ENGINE CONTROLS 1F–15
DAEWOO M-150 BL2
made to enter DTC numbers for tests which the diag-
nostic executive does not recognize, the requested in-
formation will not be displayed correctly and the scan
tool may display an error message. The same applies to
using the DTC trigger option in the Snapshot mode. If an
invalid DTC is entered, the scan tool will not trigger.
Failed Last Test
This message display indicates that the last diagnostic
test failed for the selected DTC. For type A, B and E
DTCs, this message will be displayed during subse-
quent ignition cycles until the test passes or DTCs are
cleared. For type C and type D DTCs, this message will
clear when the ignition is cycled.
Failed Since Clear
This message display indicates that the DTC has failed
at least once within the last 40 warm-up cycles since the
last time DTCs were cleared.
Failed This Ig. (Failed This Ignition)
This message display indicates that the diagnostic test
has failed at least once during the current ignition cycle.
This message will clear when DTCs are cleared or the
ignition is cycled.
History DTC
This message display indicates that the DTC has been
stored in memory as a valid fault. A DTC displayed as a
History fault may not mean that the fault is no longer
present. The history description means that all the con-
ditions necessary for reporting a fault have been met
(maybe even currently), and the information was stored
in the control module memory.
MIL Requested
This message display indicates that the DTC is currently
causing the MIL to be turned ON. Remember that only
type A B and E DTCs can request the MIL. The MIL re-
quest cannot be used to determine if the DTC fault con-
ditions are currently being experienced. This is because
the diagnostic executive will require up to three trips dur-
ing which the diagnostic test passes to turn OFF the
MIL.
Not Run Since CI (Not Run Since Cleared)
This message display indicates that the selected diag-
nostic test has not run since the last time DTCs were
cleared. Therefore, the diagnostic test status (passing
or failing) is unknown. After DTCs are cleared, this mes-
sage will continue to be displayed until the diagnostic
test runs.
Not Run This Ig. (Not Run This Ignition)
This message display indicates that the selected diag-
nostic test has not run during this ignition cycle.
Test Ran and Passed
This message display indicates that the selected diag-
nostic test has done the following:
Passed the last test.

Run and passed during this ignition cycle.

Run and passed since DTCs were last cleared.
If the indicated status of the vehicle is “Test Ran and
Passed” after a repair verification, the vehicle is ready to
be released to the customer.
If the indicated status of the vehicle is “Failed This Igni-
tion” after a repair verification, then the repair is incom-
plete and further diagnosis is required.
Prior to repairing a vehicle, status information can be
used to evaluate the state of the diagnostic test, and to
help identify an intermittent problem. The technician can
conclude that although the MIL is illuminated, the fault
condition that caused the code to set is not present. An
intermittent condition must be the cause.
PRIMARY SYSTEM-BASED
DIAGNOSTICS
There are primary system-based diagnostics which
evaluate the system operation and its effect on vehicle
emissions. The primary system-based diagnostics are
listed below with a brief description of the diagnostic
function:
Oxygen Sensor Diagnosis
The fuel control oxygen sensor (O2S) is diagnosed for
the following conditions:

Few switch count (rich to lean or lean to rich).

Slow response (average transient time lean to rich or
rich to lean).

Response time ratio (ratio of average transient time
rich(lean) to lean(rich)).

Inactive signal (output steady at bias voltage approxi-
mately 450 mV).

Signal fixed high.

Signal fixed low.
The catalyst monitor heated oxygen sensor (HO2S) is
diagnosed for the following conditions:

Heater performance (current during IGN on).

Signal fixed low during steady state conditions or
power enrichment (hard acceleration when a rich mix-
ture should be indicated).

Signal fixed high during steady state conditions or de-
celeration mode (deceleration when a lean mixture
should be indicated).

Inactive sensor (output steady at approx. 438 mV).
If the O2S pigtail wiring, connector or terminal are dam-
aged, the entire O2S assembly must be replaced. Do
not attempt to repair the wiring, connector or terminals.
In order for the sensor to function properly, it must have
clean reference air provided to it. This clean air refer-
ence is obtained by way of the O2S wire(s). Any attempt
to repair the wires, connector or terminals could result in

ENGINE CONTROLS 1F – 55
DAEWOO M-150 BL2
DIAGNOSTIC TROUBLE CODE DIAGNOSIS
CLEARING TROUBLE CODES
Notice: To prevent Engine Control Module (ECM) dam-
age, the key must be OFF when disconnecting or recon-
necting the power to the ECM (for example battery
cable, ECM pigtail connector, ECM fuse, jumper cables,
etc.).When the ECM sets a Diagnostic Trouble Code
(DTC), the Malfunction Indicator Lamp (MIL) lamp will
be turned on only for type A, B and E but a DTC will be
stored in the ECM’s memory for all types of DTC. If theproblem is intermittent, the MIL will go out after 10 sec-
onds if the fault is no longer present. The DTC will stay
in the ECM’s memory until cleared by scan tool. Remov-
ing battery voltage for 10 seconds will clear some stored
DTCs.
DTCs should be cleared after repairs have been com-
pleted. Some diagnostic tables will tell you to clear the
codes before using the chart. This allows the ECM to set
the DTC while going through the chart, which will help to
find the cause of the problem more quickly.
DIAGNOSTIC TROUBLE CODES
DTCFunctionError TypeIlluminate MIL
P0107Manifold Absolute Pressure Sensor Low VoltageAYES
P0108Manifold Absolute Pressure Sensor High voltageAYES
P0112Intake Air Temperature Sensor Low VoltageEYES
P0113Intake Air Temperature Sensor High voltageEYES
P0117Engine Coolant Temperature Sensor Low VoltageAYES
P0118Engine Coolant Temperature Sensor High voltageAYES
P0122Throttle Position Sensor Low VoltageAYES
P0123Throttle Position Sensor Hig voltageAYES
P0131Oxygen Sensor Low VoltageAYES
P0132Oxygen Sensor High VoltageAYES
P0133Oxygen Sensor No ActivityEYES
P0137Heated Oxygen Sensor Low VoltageEYES
P0138Heated Oxygen Sensor high voltageEYES
P0140Heated Oxygen Sensor No ActivityEYES
P0141Heated Oxygen Sensor Heater MalfuctionEYES
P0171Fuel Trim System Too LeanEYES
P0172Fuel Trim System Too RichEYES
P1230Fuel Pump Relay Low VoltageAYES
P1231Fuel Pump Relay High VoltageAYES
P0261Injector 1 Low VoltageAYES
P0262Injector 1 high voltageAYES
P0264Injector 2 Low VoltageAYES
P0265Injector 2 high voltageAYES
P0267Injector 3 Low VoltageAYES
P0268Injector 3 high voltageAYES
P0300Multifle Cylinder MisfireA/EBLINKING/ON
P1320Crankshatft Segment Period Segment Adaptation At LimitEYES
P1321Crankshatft Segment Period Tooth ErrorEYES
P0327Knock Sensor Circuit FaultEYES
P0335Magnetic Crankshaft Position Sensor Electrical ErrorEYES

ENGINE CONTROLS 1F–101
DAEWOO M-150 BL2
DTC P0140 – Heated Oxygen Sensor No Activity
StepActionValue(s)YesNo
1
Perform an Euro On-Board Diagnostic (EOBD)
System Check.
Is the system check complete?
–
Go to Step 2
Go to
“On-Board
Diagnostic
System Check”
2
1. Run the engine to above the specified operating
temperature.
2. Install a scan tool.
3. Operate the engine above the specified rpm for
2minuets.
Does the scan tool the indicate Closed Loop?
80°C(176°F)
1,200 rpm
Go to Step 3Go to Step 4
3
1. Turn the Turn the ignition switch to ON.
2. Review the Freeze Frame data and note the
parameters.
3. Operate the vehicle within the freeze frame
conditions and Conditions for Setting the DTC as
noted?
Does the scan tool the indicate Closed Loop?
–
Go to Step 12Go to Step 4
4
Disconnect the Heated O2 sensor connector and
jumper the Heated O2 sensor low circuit, terminal 4
to ground.
Is the HO2 voltage below the specified value and
does the scan tool indicate the heated oxygen
sensor heater voltage within the specified value?
0.5VGo to Step 5Go to Step 6
5
Check the Heated O2 sensor connector for
malfunction terminals or poor connection and repair
as necessary.
Is repair necessary?
–
Go to Step 12Go to Step 9
6
1. Turn the ignition switch to On.
2. Remove the jumper wire.
3. Using a digital voltmeter(DVM), measure the
voltage between the Heated O2 sensor signal
circuit, terminal 3 to ground.
Does the Heated O2 sensor voltage measure above
the specified value?
0.6VGo to Step 10Go to Step 9
7Does the Heated O2 sensor voltage measure below
the specified value?
0.3VGo to Step 11Go to Step 8
8
Check the Heated O2 sensor ground circuit, terminal
4 for an open or poor connection and repair as
necessary.
Is repair necessary?
–
Go to Step 12Go to Step 8
11
Check the Heated O2 sensor signal circuit, terminal
3 for an open or poor connection and repair as
necessary.
Is repair necessary?
–
Go to Step 12Go to Step 8
10
1. If disconnected, reconnect Heated O2 sensor
connector.
2. Using the scan tool, clear the DTCs.
3. Start the engine and idle at normal operating
temperature.
4. Operate the vehicle within the conditions for
setting this DTC as specified in the supporting
text.
Does the scan tool indicated that this diagnostic has
run and passed?
–
Go to Step 13Go to Step 2

1F–104 ENGINE CONTROLS
DAEWOO M-150 BL2
MAA1F140
DIAGNOSTIC TROUBLE CODE (DTC) – P0141 HEATED OXYGEN SENSOR
HEATER MALFUNCTION
Circuit Description
The engine control module (ECM) supplies a voltage of
about 450mm volts between the ECM terminals 44 and
13. The oxygen (O
2) sensor varies the voltage within a
range of about 1volt if the exhaust is rich, down to about
100mm volts if the exhaust is lean. The O
2 sensor is like
an open circuit and produces no voltage when it is below
360°C(600°F). An open O
2 sensor circuit or a cold O2
sensor causes “open loop” operation.
Conditions for Setting the DTC

Heated oxygen sensor 5V reference voltage supply
circuit high voltage or ground.

Heated oxygen sensor 5V reference voltage supply
circuit open.
Action Taken when the DTC Sets

Emission related.

“Armed” after two trip with a fail.

“Disarmed” after one trip with a pass.

MIL on if failure is detected in three consecutive trips.

Stores a History DTC on the third consecutive with a
fail (The DTC will be armed after the second fail).

Stores a Freeze Frame on the third consecutive trip
with a fail (if empty).Conditions for Clearing the MIL/DTC

The MIL will turn off after four consecutive ignition
cycles in which the diagnostic runs without a fault.

A history DTC will clear after 40 consecutive warm up
cycles without a fault.

DTC(s) can be cleared by using the scan tool.
Diagnostic Aids

Normal scan tool voltage varies between 0.1volts and
0.9 volts while in closed loop.

Inspect the oxygen (O
2) sensor wire. The O2 sensor
may be positioned incorrectly and contacting the ex-
haust manifold.

Check for an intermittent ground in the wire between
the O
2 sensor and the engine control module.

Perform an injector 2alance test to determine if a re-
stricted fuel injector may be causing the lean condi-
tion.

Vacuum of crankcase leaks will cause a lean running
condition.

An exhaust manifold gasket leak of a cracked ex-
haust manifold may cause outside air to be pulled into
the exhaust and past the sensor.