coolant temperature DODGE TRUCK 1993 Service Owner's Manual

7
- 48
COOLING
SYSTEM

•
ENGINE BLOCK HEATERS

GENERAL
INFORMATION
DESCRIPTION AND OPERATION An optional engine block heater
is
available with
for
all
models. The heater
is
equipped with
a
power
cord that
is
located behind the grille. The cord
is at­

tached
to an
engine compartment component with
tie-straps.
The
heater warms
the
engine providing easier engine starting
and
faster warm-up
in low

temperatures. The heater
is
mounted
in a
core hole of the engine cylinder block (in place of
a
freeze plug)
with
the
heating element immersed
in
engine cool­ ant.
The
power cord
is
located behind
the
radiator
grille. Connect the power cord
to a
grounded 110-120
volt AC electrical outlet with
a
grounded, three wire
extension cord.

WARNING:
DO NOT
OPERATE ENGINE
UNLESS
BLOCK
HEATER
CORD
HAS
BEEN
DISCONNECTED
FROM POWER
SOURCE
AND
SECURED
IN
PLACE.

THE POWER
CORD
MUST BE
SECURED
IN ITS RE­
TAINING
CLIPS
AND ROUTED AWAY FROM
EX­
HAUST MANIFOLDS AND MOVING
PARTS.

REMOVAL
(1) Disconnect negative battery cable from battery.
(2) Drain coolant from radiator and cylinder block.
(3) Remove pow^r cord from heater (Fig.
1 or 2).

(4)
Loosen bolt
at
center
of
block heater. Remove
block heater.
INSTALLATION (1) Thoroughly clean cylinder block core hole
and

block heater seat. (2) Insert block heater (with element loop pointing

down).

(3) With heater fully seated, tighten center bolt se­
curely.

(4)
Fill cooling system with recommended coolant.
Refer
to
Refilling Cooling System section
in
this
group.
Fig.
1
Engine
Block
Heater—Except
Diesel

Fig.
2
Engine
Block
Heater—Diesel
Engine

•

IGNITION
SYSTEMS
8D
- 1
CONTENTS

page page
COMPONENT IDENTIFICATION/SYSTEM DIAGNOSTICS/SERVICE PROCEDURES
7
OPERATION
1
IGNITION SWITCH
25

COMPONENT REMOVAL/INSTALLATION
..... 18
SPECIFICATIONS
28

COMPONENT
IDENTIFICATION/SYSTEM OPERATION
INDEX
page

Automatic
Shut Down (ASD) Relay
1
Camshaft Position Sensor
2

Crankshaft Position Sensor
2

Distributors
3

Engine Coolant
Temperature
Sensor
...........
4

General
Information
1
page

Ignition
Coil
3
Intake
Manifold Charge
Air
Temperature
Sensor
. . 4

Manifold Absolute Pressure (MAP) Sensor
4
Powertrain
Control
Module (PCM)
. 5

Throttle
Position Sensor
5

GENERAL
INFORMATION
Throughout this group, references
are
made
to
par­
ticular vehicle models
by
alphabetical designation
or

by
the
particular vehicle nameplate.
A
chart showing a breakdown
of
alphabetical designations
is
included
in
the
Introduction group
at the
beginning
of
this
manual. 5.9L
gas
powered engines will
be
referred
to as ei­

ther: LDC (Light Duty Cycle),
or
HDC (Heavy Duty Cycle). This section
of the
group, Component Identifica­
tion/System Operation, will discuss ignition system operation
and
will identify ignition system compo­

nents.
For diagnostic procedures
and
adjustments, refer
to

the Diagnostics/Service Procedures section
of
this
group.
For removal
and
installation
of
ignition system
components, refer
to the
Component Removal/Instal­
lation section
of
this group. For other useful information, refer
to
On-Board
Di­

agnostics
in the
General Diagnosis sections
of
Group
14,
Fuel System
in
this manual. For operation
of the DRB II
Diagnostic Scan Tool,
refer
to the
appropriate Powertrain Diagnostic Proce­
dures service manual.
An Ignition specifications section
is
included
at the

end
of
this group.
A
general Maintenance Schedule (mileage intervals)
for
ignition related items
can be
found
in
Group
0,
Lubrication and Maintenance. This
schedule
can
also
be
found
in the
Owners Manual.

IGNITION
SYSTEMS
The ignition systems used
on all
engines
are
basi­
cally identical. Similarities
and
differences between
the systems will
be
discussed.
A sequential multi-port fuel injection system
is

used
on all gas
powered engines.
The ignition system
is
controlled
by the
powertrain
control module (PCM)
on all
engines.
The
PCM
was

formerly referred
to as the
SBEC
or
engine control­ ler.
The ignition system consists
of:

• Spark Plugs
• Ignition Coil
• Secondary Ignition Cables
• Ignition distributor. Contains rotor
and
camshaft
position sensor • Powertrain Control Module (PCM)
• Crankshaft Position Sensor

AUTOMATIC SHUT DOWN (ASD) RELAY
The automatic shut down (ASD) relay
is
located
in

the engine compartment (Fig.
1). As one of its
func­

tions,
the ASD
relay will supply battery voltage
to
the ignition coil.
The
ground circuit
for the
ASD
re­

lay
is
controlled
by the
powertrain control module (PCM).
The PCM
regulates
ASD
relay operation
by
switching
the
ground circuit on-and-off.

IGNITION
SYSTEMS

8D
- 4
IGNITION
SYSTEMS

•
Fig. 6 ignition Coil—3.9L/5.2L/5.9L
LDC-Gas
Engines Fig. 7 Ignition Coil—5.9L
HDC-Gas
Engine
• 5.9L HDC-Gas Engines: The coil is mounted to a
bracket that is bolted to the automatic belt tensioner mounting bracket (Fig. 7).
For component testing, refer to the Diagnostics/Ser­
vice Procedures section of this group.
For removal and installation of this component, re­
fer to the Component Removal/Installation section of
this group.

ENGINE COOLANT TEMPERATURE
SENSOR
The sensor provides an input voltage to the power-
train control module (PCM) relating coolant temper­ ature. The PCM uses this input, along with inputs
from other sensors, to determine injector pulse width and ignition timing. As coolant temperature varies,
the coolant temperature sensor resistance will
change, resulting in a different input voltage to the
PCM. When the engine is cold, the PCM will operate in
the Open Loop Cycle. It will demand slightly richer air-fuel mixtures and higher idle speeds, until nor­ mal operating temperatures are reached. Refer to
Modes Of Operation in Group 14, Fuel System for a
description of Open and Closed Loop operation.
The sensor is installed in the intake manifold near
the thermostat housing (Fig. 8).
Fig. 8 Coolant Temperature Sensor—Typical
For component testing, refer to the Diagnostics/Ser­
vice Procedures section of this group. For removal and installation of this component, re­
fer to the Component Removal/Installation section of
this group.

INTAKE MANIFOLD CHARGE
AIR
TEMPERATURE

SENSOR
The sensor element extends into the intake mani­
fold air stream. It provides an input voltage to the
powertrain control module (PCM) indicating intake
manifold air temperature. The input from this sensor is used along with inputs from other sensors to de­
termine injector pulse width. As the temperature of
the air-fuel stream in the manifold varies, the sensor
resistance will change. This will result in a different input voltage to the PCM. For more information, re­
fer to Group 14, Fuel System. This sensor is installed in the intake manifold

(Figs.
9 or 10). For component testing, refer to the Diagnostics/Ser­
vice Procedures section of this group. For removal and installation of this component, re­
fer to the Component Removal/Installation section of
this group.

MANIFOLD ABSOLUTE
PRESSURE
(MAP)
SENSOR
The MAP sensor reacts to absolute pressure in the
intake manifold and provides an input voltage to the
powertrain control module (PCM). As engine load changes, manifold pressure varies, causing the MAP
sensor voltage to change. This change results in a
different input voltage to the PCM. The input volt­ age level supplies the PCM with information. This
relates to ambient barometric pressure during engine

•

IGNITION
SYSTEMS
80 - 7
DIAGNOSTICS/SERW1CE
PROCEDURES

INDEX

page

Automatic Shut Down (ASD) Relay
7
Camshaft Position
Sensor
Test
...............
7

Crankshaft Position
Sensor
Test
8

Distributor
Cap
8

Distributor
Rotor
8
Engine
Coolant Temperature
Sensor
Test
10

General
Information
7

Ignition
Coil
8

Ignition
Secondary
Circuit
Diagnosis
10

GENERAL
INFORMATION
This section
of the
group, Diagnostics/Service Pro­
cedures, will discuss basic ignition system diagnos­
tics
and
service adjustments. For system operation
and
component identification,
refer
to the
Component Identification/System Opera­
tion section
of
this group. For removal
or
installation
of
ignition system com­
ponents, refer
to the
Component Removal/Installa­
tion section
of
this group. For other useful information, refer
to
On-Board
Di­

agnostics
in the
General Diagnosis sections
of
Group
14,
Fuel System
in
this manual. For operation
of the DRB II
Diagnostic Scan Tool,
refer
to the
appropriate Powertrain Diagnostic Proce­
dures service manual.

AUTOMATIC SHUT DOWN
(ASD)
RELAY
Refer
to
Relays—Operation/Testing
in the
Group

14,
Fuel System section
of
this service manual.

CAMSHAFT POSITION SENSOR TEST
The camshaft position sensor
is
located
in the
dis­
tributor
on all
engines. To perform
a
complete test
of
this sensor
and its

circuitry, refer
to the DRB II
diagnostic scan tool.
Also refer
to the
appropriate Powertrain Diagnostics
Procedures manual.
To
test
the
sensor only, refer
to

the following: For this test,
an
analog (non-digital) voltmeter
is needed.
Do not
remove
the
distributor connector from
the
distributor. Using small paper clips, insert
them into
the
backside
of the
distributor wire har­ ness connector
to
make contact with
the
terminals.
Be sure that
the
connector
is not
damaged when
in­
serting
the
paper clips. Attach voltmeter leads
to

these paper clips. (1) Connect
the
positive (
+
)
voltmeter lead into
the sensor output wire. This
is at
done
the
distribu­ tor wire harness connector.
For
wire identification,
refer
to
Group
8W,
Wiring Diagrams.
page

Ignition
Timing
12

Intake Manifold Charge
Air
Temperature
Sensor
Test
12

Manifold Absolute Pressure (MAP)
Sensor
Test
. 12

Oxygen
Sensor
Tests
17
Powertrain Control Module (PCM)
............
14

Spark
Plug Secondary Cables
16

Spark
Plugs
............................
14

Throttle
Position
Sensor
Test
17

(2) Connect
the
negative
(-)
voltmeter lead into
the

ground wire.
For
wire identification, refer
to
Group
8W, Wiring Diagrams.
(3)
Set the
voltmeter
to the 15
Volt
DC
scale. (4) Remove distributor
cap
from distributor
(two

screws). Rotate (crank)
the
engine until
the
distribu­
tor rotor
is
pointed towards
the
rear
of
vehicle.
The

movable pulse ring should
now be
within
the
sensor
pickup.
(5) Turn ignition
key to ON
position. Voltmeter
should read approximately
5.0
volts.
(6)
If
voltage
is not
present, check
the
voltmeter
leads
for a
good connection.
(7)
If
voltage
is
still
not
present, check
for
voltage
at
the
supply wire.
For
wire identification, refer
to

Group
8W,
Wiring Diagrams.
(8)
If
voltage
is not
present
at
supply wire, check
for voltage
at
pin-7
of
powertrain control module (PCM) 60-way connector. Leave
the PCM
connector
connected
for
this test. (9)
If
voltage
is
still
not
present, perform vehicle
test using
the DRB II
diagnostic scan tool. (10)
If
voltage
is
present
at
pin-7,
but not at the

supply wire: (a) Check continuity between
the
supply wire.
This
is
checked between
the
distributor connector and pin-7
at the PCM. If
continuity
is not
present,
repair
the
harness
as
necessary. (b) Check
for
continuity between
the
camshaft
position sensor output wire
and
pin-44
at the PCM.
If continuity
is not
present, repair
the
harness
as
necessary. (c) Check
for
continuity between
the
ground cir­
cuit wire
at the
distributor connector
and
ground.
If continuity
is not
present, repair
the
harness
as
necessary. (11) While observing
the
voltmeter, crank
the en­

gine with ignition switch.
The
voltmeter needle should fluctuate between
0 and 5
volts while
the en­

gine
is
cranking. This verifies that
the
camshaft
po­
sition sensor
in the
distributor
is
operating properly
and
a
sync pulse signal
is
being generated.

8D
- 10
IGNITION
SYSTEMS

• Arcing at the tower will carbonize the cable boot,
which if it is connected to a new ignition coil, will cause the coil to fail. If the secondary coil cable shows any signs of dam­

age,
it should be replaced with a new cable and new
terminal. Carbon tracking on the old cable can cause
arcing and the failure of a new ignition coil.

ENGINE
COOLANT
TEMPERATURE
SENSOR
TEST
To perform a complete test of this sensor and its
circuitry, refer to the DRB II diagnostic scan tool.
Also refer to the appropriate Powertrain Diagnostics
Procedures manual. To test the sensor only, refer to
the following: The sensor is located in a water passage of the in­
take manifold next to the thermostat housing (Fig.
8).
(1) Disconnect wire harness connector from sensor
(Fig. 8). On engines with air conditioning, do not pull
directly on wiring harness. Fabricate an L-shaped
hook tool from a coat hanger (approximately eight inches long). Place the hook part of tool under the
connector for removal. The connector is snapped onto
the sensor. It is not equipped with a lock type tab.
COOLANT

TEMPERATURE
SENSOR
SENSOR RESISTANCE (OHMSJ
V

J9314-78

Fig. 8 Coolant Temperature Sensor—Typical (2) Test the resistance of the sensor with a high in­
put impedance (digital) volt-ohmmeter. The resis­ tance should be less than 1340 ohms at normal
engine operating idle temperature. For resistance
values, refer to the Sensor Resistance chart. Replace
the sensor if it is not within the range of resistance specified in the chart.
(3) Test continuity of the wire harness. This is
done between powertrain control module (PCM) wire
harness connector terminal-2 and the sensor connec­
tor terminal. Also check continuity between wire harness terminal-4 to the sensor connector terminal. Repair the wire harness if an open circuit is indi­
cated.
TEMPERATURE

RESISTANCE
(OHMS)

C
F
MIN
MAX

-40 -40 291,490 381,710
-20
-4
85,850
108,390
-10 14
49,250 61,430

0
32 29,330
35,990
10 50 17,990 21,810
20 68 11,370 13,610

25
77 9,120 10,880
30 86
7,370

8,750

40 104

4,900
5,750

50 122
3,330 3,880

60 140 2,310

2,670

70 158
1,630 1,870

80 176
1,170 1,340

90 194
860
970
100 212 640
720
110 230 480 540
120 248 370 410

J928D-4

IGNITION
SECONDARY
CIRCUIT
DIAGNOSIS

CHECKING FOR SPARK

CAUTION:
When
disconnecting a
high
voltage
cable

from
a spark
plug
or
from
the
distributor
cap,
twist
the rubber
boot
slightly
(1/2
turn)
to
break
it
loose.
Grasp
the
boot
(not the cable) and
pull
it off
with
a

steady,
even force.

(1) Disconnect the ignition coil secondary cable
from center tower of the distributor cap. Hold the ca­
ble terminal approximately 12 mm (1/2 in.) from a good engine ground (Fig. 9).
CHECK
HERE

FOR
SPARK
IGNITION

COIL
918D-18

Fig. 9 Checking for Spark—Typical

8D
- 18
IGNITION
SYSTEMS

•
COMPONENT REMGWAL/INSTALLATION

INDEX

page

Automatic
Shut Down (ASD) Relay
18
Camshaft
Position
Sensor
, 18

Crankshaft Position
Sensor
18
Distributor
Service
20
Engine
Coolant Temperature
Sensor
20

General
Information
18
Ignition
Coil
21
page

Intake
Manifold Charge
Air
Temperature
Sensor
. 22

Manifold Absolute Pressure (MAP)
Sensor
..... 22

Oxygen
(02)
Sensor
22
Powertrain
Control
Module (PCM)
22

Spark
Plug Secondary Cables
24

Spark
Plugs
23

Throttle
Position
Sensor
(TPS)
24

GENERAL
INFORMATION
This section
of the
group, Component Removal/In­
stallation, will discuss
the
removal
and
installation
of ignition system components. For basic ignition system diagnostics
and
service
adjustments, refer
to the
Diagnostics/Service Proce­
dures section
of
this group. For system operation
and
component identification,
refer
to the
Component Identification/System Opera­
tion section
of
this group.

AUTOMATIC
SHUT DOWN
(ASb)
RELAY
The automatic shut down
(ASD)
relay
is
located
in

the engine compartment
(Fig. 1).
TORQUE CONVERTER
CLUTCH RELAY
A/C
CLUTCH RELAY STARTER RELAY

AUTO
SHUTDOWN RELAY FUEL PUMP RELAY DATA UNK
CONNECTOR POWERTRAIN
CONTROL
MODULE
J9314-164

Fig.
1
Auto
Shut Down
Relay
REMOVAL

(1) Disconnect negative battery cable
at
battery.

(2)
Remove
the
relay
by
pulling from connector.

INSTALLATION
(1) Check
the
terminals
in the
relay connector
for

corrosion
or
damage before installation.

(2)
Push
the
relay into
the
connector.

CAMSHAFT POSITION SENSOR
The camshaft position sensor
is
located
in the
dis­
tributor
(Fig. 2).
REMOVAL

Distributor removal
is not
necessary
to
remove
camshaft position sensor.

CAMSHAFT POSITION
SENSOR
SYNC

SIGNAL

GENERATOR
DISTRIBUTOR
ASSEMBLY
J9314-82

Fig.
2
Camshaft Position Sensor—Typical
(1) Disconnect negative battery cable
at
battery.

(2)
Remove distributor
cap
from distributor
(two

screws).
(3) Disconnect camshaft position sensor wiring
harness from main engine wiring harness.
(4) Remove distributor rotor from distributor shaft.

(5)
Lift
the
camshaft position sensor assembly from
the distributor housing
(Fig. 2).

INSTALLATION
(1) Install camshaft position sensor
to
distributor.
Align sensor into notch
on
distributor housing.
(2)
Connect wiring harness.
(3) Install rotor.
(4) Install distributor
cap.
Tighten mounting
screws.

CRANKSHAFT
POSITION SENSOR
REMOVAL The sensor
is
bolted
to the top of the
cylinder block
near
the
rear
of
right cylinder head
(Fig. 3).

8D
- 20
IGNITION
SYSTEMS

•
ENGINE
COOLANT
TEMPERATURE
SENSOR

WARNING: HOT, PRESSURIZED COOLANT CAN CAUSE INJURY BY SCALDING. COOLING SYSTEM MUST BE PARTIALLY DRAINED BEFORE REMOV­
ING THE COOLANT TEMPERATURE SENSOR. RE­
FER TO GROUP 7, COOLING.

REMOVAL
(1) Partially drain cooling system. Refer to Group
7, Cooling.

(2)
Disconnect electrical connector from sensor
(Fig. 5). Engines with air conditioning: When removing
the connector from sensor, do not pull directly on
wiring harness. Fabricate an L-shaped hook tool
from a coat hanger (approximately eight inches
long).
Place the hook part of tool under the connector
for removal. The connector is snapped onto the sen­ sor. It is not equipped with a lock type tab.
(3) Remove sensor from intake manifold.
Fig. 5 Coolant Temperature
Sensor—
Typical

INSTALLATION
(1) Install sensor.
(2) Tighten to 7 Nnn (5.5 ft. lbs.) torque.
(3) Connect electrical connector to sensor.
The sensor connector is symmetrical (not indexed).
It can be installed to the sensor in either direction. (4) Replace any lost engine coolant. Refer to Group
7, Cooling System.

DISTRIBUTOR
SERVICE

REMOVAL

CAUTION:
Base
ignition timing
is not
adjustable
on

any
engine. Distributors
do not
have
built
in
centrif­
ugal
or
vacuum assisted advance.
Base
ignition
timing
and
timing advance
are
controlled
by the
powertrain control module
(PCM).
Because
a
con­
ventional timing light can
not be
used
to
adjust
dis­

tributor
position
after
installation, note position
of
distributor before removal.

(1) Disconnect negative battery cable at battery.
(2) Remove distributor cap from distributor (two
screws).
(3) Mark the position of distributor housing in
relationship to engine or dash panel. This is done
to aid in installation. Before distributor is removed, the number one cyl­
inder must be brought to the top dead center (TDC)
firing position. (4) Attach a socket to the Crankshaft Vibration
Damper mounting bolt.
(5) Slowly rotate engine clockwise, as viewed from
front, until indicating mark on crankshaft vibration damper is aligned to 0 degree (TDC) mark on timing
chain cover (Fig. 6).
Fig. 6 Damper-To-Cover Alignment Marks—Typical (6) The distributor rotor should now be aligned to
the CYL. NO. 1 alignment mark (stamped) into the camshaft position sensor (Fig. 7). If not, rotate the
crankshaft through another complete 360 degree

turn.
Note the position of the number one cylinder spark plug cable (on the cap) in relation to rotor. Ro­
tor should now be aligned to this position.
(7) Disconnect camshaft position sensor wiring
harness from main engine wiring harness.
(8) Remove distributor rotor from distributor shaft. (9) Remove distributor holddown clamp bolt and
clamp (Fig. 8). Remove distributor from vehicle.
CAUTION: Do not
crank engine
with
distributor
re­
moved.
Distributor/crankshaft relationship
will
be

lost.

• • ^ ^ ^ INSTRUMENT PANEL AND GAUGES 8E - 1
CONTENTS

page
CLUSTER AND GAUGE SERVICE PROCEDURES . 12
CLUSTER AND GAUGE TEST PROCEDURES .. i
GENERAL INFORMATION . 1
page

MESSAGE CENTER-DIESEL ENGINE ........ 4
MESSAGE CENTER-GAS ENGINE .......... 3

SWITCH
AND PANEL COMPONENT SERVICE . 16
GENERAL
INFORMATION
INDEX

page

Generator
Indicating
System
2
Distance
Sensor
2

Electronic
Digital
Clock
3

Fuel
Level
Indicating
System
1
page

Malfunction
Indicator
(Check
Engine)
3

Oil
Pressure
Warning
Lamp
................. 2
Speedometer/Odometer
System
2

Temperature
and Oil
Indicating
System
......... 2
D-body trucks have an instrument cluster which
includes gauges for fuel level, coolant temperature,
oil pressure, and charging system voltage (Fig. 1).
When the ignition switch is in the OFF position all
the gauges will show a reading except the voltage gauge. However, the readings are only accurate
when the ignition switch is in the ON position.
The cluster also includes warning lamps for:
• seat belt warning
• low oil pressure
• high beam
• left and right turn signals
• check engine. J908E-66

Fig.
11nstrument
Cluster
FUEL LEVEL INDICATING SYSTEM (FIG. 2)
A hinged float arm in the fuel tank raises or lowers
depending on the fuel level. The float arm contacts a
variable resistor in the gauge sending unit. This pro­
vides a change of resistance in the fuel gauge circuit
with any up or down movement of the float. This sender
resistance is shown as fuel level on the gauge. Resistance is greatest when the fuel level in the
tank is low and the float arm drops. With high resis­
tance current flow is low and consequently positions
the instrument panel gauge pointer to low.
Resistance in the circuit is at a minimum when the
tank is full and the float arm is raised. With resis­
tance at a minimum, current flow is high registering
full on the instrument panel gauge.
12
VOLTS
TO

GAUGE
IP

FUEL
TANK

SENDING
UNIT

FLOAT

SENDING
UNIT
1:
1
j
^
fCONNECTOR

!g|yj-»—
FUEL

GAUGE

FUEL

TANK

J098E-47

Fig.
2
Fuel
Level
Indicating
System

INSTRUMENT PANEL AND GAUGES

8E
- 2
INSTRUMENT PANEL
AND
GAUGES

•
TEMPERATURE AND
OIL
INDICATING SYSTEM
(FIG.
3) The operation of the temperature and oil pressure
indicating systems are identical. In the temperature
system the sending unit resistance varies in direct
relationship to the temperature of the coolant. When the engine is cold, the resistance of the tem­
perature sending unit is high and a cold temperature
will be indicated on the gauge. When the engine is hot, the resistance of the tem­
perature sending unit is low and a hot temperature
will be indicated on the gauge. In the oil pressure indicating system the sending
unit resistance is actuated by a diaphragm as the oil
pressure increases or decreases. Low oil pressure causes high resistance. High pressure causes low re­
sistance. 12
VOLTS
TO
GAUGE
TEMPERATURE/
OIL GAUGE
TEMPERATURE/OIL SENDING
UNIT
J908E-48
Fig. 3 Temperature/Oil indicating System

OIL
PRESSURE
WARNING LAMP
The oil pressure warning switch, mounted on the
engine, is controlled by engine oil pressure. When engine oil pressure is normal, the switch is
held in the OFF or OPEN position. This stops cur­
rent from flowing to the oil pressure warning lamp
on instrument panel. When the engine oil pressure is low, the switch is
in the ON or CLOSED position. This allows current
to flow to the oil pressure warning lamp in the in­ strument cluster causing the warning lamp to illumi­

nate.
GENERATOR
INDICATING
SYSTEM
(FIG. 4)
The voltmeter gauge senses the voltage of the elec­
trical system.
VOLTAGE
/*

GAUGE
P/
J908E-49 Fig. 4 Generator Indicating System

SPEEDOMETER/ODOMETER SYSTEM
The speedometer/odometer system consists of an
electric speedometer and pushbutton reset odometer
mounted in the cluster. The system also includes the
wire harness from the cluster to the distance sensor at the transmission, and the adapter and pinion in
the transmission. The speedometer/odometer has the same appearance as a conventional version but it
eliminates the cable-driven mechanical system. A signal is sent from a transmission mounted distance
sensor to the speedometer/odometer circuitry through
the wiring harness. By eliminating the speedometer cable, instrument cluster service and removal is im­
proved. Refer to Group 21 - Transmission for select­ ing the proper pinion, and selecting and indexing the
proper adapter.

DISTANCE
SENSOR

DISTANCE SENSOR TEST For testing of the distance sensor and related com­
ponents refer to the Vehicle Diagnostics Test Proce­ dure Manual.
DISTANCE SENSOR REMOVAL AND INSTALLATION (1) Remove harness connector from sensor. Be sure
weather seal stays on harness connector. (2) Remove sensor by loosening sensor coupling
nut from the pinion gear adapter until sensor is free (Fig. 5).
(3) To install the sensor, reverse the removal pro­
cedures. Tighten coupling nut to 17 N»m (150 in. lbs.)

•

INSTRUMENT PANEL
AND
GAUGES
8E - 3
MALFUNCTION INDICATOR (CHECK ENGINE)

Fig.
5
Distance Sensor
If
the
input from
one of the
following sensors fails
an internal Powertrain Control Module
(PCM)
self
check,
the PCM
turns
on the
Check Engine Lamp. The
PCM
then substitutes
a
modified signal
in
place
of
the one
that failed until
a
repair
is
made:
• Manifold Absolute Pressure (MAP) Sensor
• Throttle Position Sensor
• Coolant Temperature Sensor
• Battery Voltage Sense
• Battery Voltage
Too
High
Refer
to the
appropriate Powertrain Diagnostic
Test Procedures manual
for
further information.

ELECTRONIC DIGITAL CLOCK
The electronic digital clock
is in the
radio.
The

clock
and
radio each
use the
display panel built into
the radio.
A
digital readout indicates
the
time
in

hours
and
minutes whenever
the
ignition switch
is in

the
ON or ACC
position. When
the
ignition switch
is in the OFF
position
or

when
the
radio frequency
is
being displayed, time keeping
is
accurately maintained. The procedure
for
setting
the
clock varies slightly
with each radio.
The
correct procedure
is
described under
the
individual radio operating instructions
re­

ferred
to in the
Owner Manual supplied with
the ve­

hicle.

MESSAGE CENTER—GAS ENGINE

The message center
(Fig. 6),
located above
the

Heater-A/C controls, includes warning lamps
for the:

• brake systems (parking
and
service)
•
ABS
brakes • liftgate open (Ramcharger only)
• maintenance required.

O/D
BRAKE
(P)(7

GATE OPEN

MAINT
REQD.

J938E-54
Fig.
6
Message Center—Gas Engine

EMISSIONS
MAINTENANCE REMINDER
This system
is
designed
to act as a
reminder that
scheduled vehicle emissions maintenance should
be

performed.
It is not
intended
to
indicate
a
warn­
ing
or
that
a
state
of
emergency exists which must
be
corrected
to
insure safe vehicle opera­
tion.
The
components covered
by the
system include
the
EGR
system,
PCV
valve,
and
oxygen sensor. Refer
to
Group
25 -
Emissions,
for
further informa­
tion.

ABS
WARNING
LIGHT
This light monitors
the ABS
Brake System. This
light will come
on
when
the
ignition
key is
turned
to

the
ON
position
and may
stay
on for as
long
as

thirty seconds.
If the ABS
light remains
on or
comes on during driving,
it
indicates that
the ABS
portion
of
the
brake system
is not
functioning. Refer
to
Group
5 -
Brakes
for
further information.

BRAKE
SYSTEM WARNING
LIGHT
The dual brake system provides
a
reserve braking
capability
in the
event
of a
failure
to a
portion
of the

hydraulic system. Failure
of
either
of the
dual sys­
tem
is
indicated
by the
brake warning light which
will glow when
the
service brake pedal
is
depressed.
The light will remain
on
until
the
cause
is
corrected. The light will also come
on
when
the
parking
brake
is
applied with
the
ignition
in the ON
position.
Refer
to
Group
5 -
Brakes
for
further information.