FIAT PUNTO EVO 2010 1.G Owners Manual

190
F0U0250mfig. 167
DAYTIME RUNNING LIGHTS (DRL)
To change the bulb, proceed as follows:
❒turn the bulb holder A-fig. 167 anti-clockwise using the
tab and pull it out;
❒remove the bulb B by pushing it in slightly and turning
it anti-clockwise;
❒refit the bulb holder by putting it in its housing and turn-
ing it clockwise until it locks into place.
KNOWING
YOUR
VEHICLE
SAFETY
STARTING
AND DRIVING
WARNING LIGHTS
AND MESSAGES
IN AN
EMERGENCY
SERVICING
AND CARE
TECHNICAL
SPECIFICATIONS
CONTENTS
F0U0150mfig. 168
MAIN/DIPPED BEAM HEADLIGHTS
To change the bulb, proceed as follows:
❒remove the rubber cap;
❒disconnect the central electric connector B-fig. 168 and
release the bulb holder catch;
❒remove the bulb A and replace it;
❒fit the new bulb, aligning the outlines of the metallic part
with the grooves on the reflector;
❒refit the bulb holder catch and reconnect the electri-
cal connector;
❒refit the cap A, ensuring that it locks into place.
175-210 PUNTO FL EN 4ed 20-01-2010 15:09 Pagina 190

191
KNOWING
YOUR
VEHICLE
SAFETY
STARTING
AND DRIVING
WARNING LIGHTS
AND MESSAGES
IN AN
EMERGENCY
SERVICING
AND CARE
TECHNICAL
SPECIFICATIONS
CONTENTS
F0U0152mfig. 170
A
A
B
F0U0151mfig. 169
DIRECTION INDICATORS
Front fig. 169
To change the bulb, proceed as follows:
❒steer the right/left wheel inwards;
❒turn the catch A-fig. 169, then lift off the access lid B;
D
F0U0153mfig. 171
❒remove the bulb holder cover C-fig. 170 by turning it
anti-clockwise;
❒remove the bulb D-fig. 171 by pushing it in gently and
turning anti-clockwise (“bayonet” clamping), then re-
place it;
❒refit the bulb holder cover C-fig. 170 by turning it clock-
wise and locking it properly;
❒close the lid B-fig.169 then tighten the catch A.
175-210 PUNTO FL EN 4ed 20-01-2010 15:09 Pagina 191

192
KNOWING
YOUR
VEHICLE
SAFETY
STARTING
AND DRIVING
WARNING LIGHTS
AND MESSAGES
IN AN
EMERGENCY
SERVICING
AND CARE
TECHNICAL
SPECIFICATIONS
CONTENTS
A
F0U0526mfig. 173/b
❒loosen the fixing screws C and remove the headlamp;
❒remove the bulb A-fig.173/b by rotating it counter-
clockwise and disconnect the electrical connector.
F0U0280mfig. 172
Side fig. 172
To change the bulb, proceed as follows:
❒slide the lens A towards the front of the car to press
in the internal catch B, then pull the unit outwards;
❒turn the bulb holder C anti-clockwise, extract bulb D
and replace it;
❒refit the bulb holder C into the lens by turning it clock-
wise;
❒refit the unit making sure the internal catch B clicks in-
to place.
FRONT FOG LIGHTS
(for versions/markets where provided)
To replace the bulb:
❒loosen the screw A-fig.173/a and remove the protec-
tion template B;
C
AC
B
C
F0U0525mfig. 173/a
175-210 PUNTO FL EN 4ed 20-01-2010 15:09 Pagina 192

193
KNOWING
YOUR
VEHICLE
SAFETY
STARTING
AND DRIVING
WARNING LIGHTS
AND MESSAGES
IN AN
EMERGENCY
SERVICING
AND CARE
TECHNICAL
SPECIFICATIONS
CONTENTS
REAR LIGHT CLUSTERS
The rear light clusters contain taillight, brake light and di-
rection indicator bulbs.
The bulbs are arranged inside the light cluster fig. 174 as
follows:
D direction indicators
E brake lights.
F0U0155mfig. 174F0U0156mfig. 175
To change the bulb proceed as follows:
❒undo both fastening bolts A-fig 174;
❒disconnect the central electric connector B and pull the
lens unit outwards;
❒ unhook the bulb holder by unclipping the fasteners
C-fig. 175;
❒remove the bulb by pushing it in gently and turning an-
ti-clockwise (“bayonet” clamping), then replace it;
175-210 PUNTO FL EN 4ed 20-01-2010 15:09 Pagina 193

194
KNOWING
YOUR
VEHICLE
SAFETY
STARTING
AND DRIVING
WARNING LIGHTS
AND MESSAGES
IN AN
EMERGENCY
SERVICING
AND CARE
TECHNICAL
SPECIFICATIONS
CONTENTS
❒refit the bulb holder;
❒reconnect the electric connector, correctly realign the
unit with the car body and then tighten the fastening
screws A.
IMPORTANT To replace the LED taillights you must con-
tact a Fiat Dealership.
REAR FOG LIGHTS fig. 176
Contact a Fiat Dealership to have bulbs for the rear fog
lights A replaced.
REVERSE LIGHTS fig. 176
Contact a Fiat Dealership to have bulbs for the reverse
lights B replaced.
F0U0157mfig. 176F0U0281mfig. 177
THIRD BRAKE LIGHT fig. 177
To change the bulb proceed as follows:
❒open the boot;
❒remove the rubber caps;
❒press in the catches and remove the lens unit
C-fig. 177;
❒disconnect the electric connector;
❒press in the tabs D-fig. 177 and remove the bulb holder;
❒remove the snap-fitted bulb and replace it.
NUMBER PLATE LIGHTS
To change the bulb proceed as follows:
❒manipulate the point shown by the arrow and remove
the lens unit A-fig. 178;
175-210 PUNTO FL EN 4ed 20-01-2010 15:09 Pagina 194

195
KNOWING
YOUR
VEHICLE
SAFETY
STARTING
AND DRIVING
WARNING LIGHTS
AND MESSAGES
IN AN
EMERGENCY
SERVICING
AND CARE
TECHNICAL
SPECIFICATIONS
CONTENTS
F0U0160mfig. 179
F0U0159mfig. 178
❒change the bulb fig.179 by releasing it from the side
contacts and making sure the new bulb is correctly fas-
tened between these contacts;
❒refit the snap-fitted lens unit.
F0U0163mfig. 180
CHANGING AN INTERIOR BULB
For the type of bulb and relevant power rating, see
“Changing a bulb”.
FRONT CEILING LIGHT
Proceed as follows to replace the bulbs:
❒manipulate the points shown by the arrows and remove
light A-fig. 180;
❒ open the protective flap B-fig. 181;
❒replace bulbs C-fig. 181 by releasing them from the side
contacts and making sure that new bulbs are correctly
clamped between these contacts;
❒close the flap B-fig. 181 and fasten the courtesy light
A-fig. 180 in its housing, making sure it is locked in cor-
rectly.
175-210 PUNTO FL EN 4ed 20-01-2010 15:09 Pagina 195

F0U0164mfig. 181
REAR CEILING LIGHT
(for versions/markets where provided)
Proceed as follows to replace the bulbs:
❒manipulate the points shown by the arrows and remove
light D-fig. 182;
❒open the protective flap E-fig. 183;
❒replace bulb F-fig. 183 by releasing it from the side con-
tacts and making sure that the new bulb is correctly
clamped between these contacts;
❒re-close the protective flap E-fig. 183 and fit light D-fig.
182 into its housing, making sure it locks into place
properly.
196
KNOWING
YOUR
VEHICLE
SAFETY
STARTING
AND DRIVING
WARNING LIGHTS
AND MESSAGES
IN AN
EMERGENCY
SERVICING
AND CARE
TECHNICAL
SPECIFICATIONS
CONTENTS
F0U0166mfig. 183
F0U0165mfig. 182
COURTESY LIGHT fig. 184
To change the bulb, proceed as follows:
❒remove the light A-fig. 184 by levering on the points
shown by the arrow.
175-210 PUNTO FL EN 4ed 20-01-2010 15:09 Pagina 196

197
KNOWING
YOUR
VEHICLE
SAFETY
STARTING
AND DRIVING
WARNING LIGHTS
AND MESSAGES
IN AN
EMERGENCY
SERVICING
AND CARE
TECHNICAL
SPECIFICATIONS
CONTENTS
F0U0167mfig. 184
BOOT LIGHT fig. 185
To change the bulb, proceed as follows:
❒open the boot;
❒remove the light A-fig. 185 by levering on the point
shown by the arrow.
❒open the protective cover B and replace the snap-fitted
bulb;
❒re-close the protective cover B over the lens;
❒refit the light A by inserting it in its correct position first-
ly on one side and then on the other until it clicks into
place.
F0U0168mfig. 185
PUDDLE LIGHTS fig. 186
(for versions/markets where provided)
To change the bulb, proceed as follows:
❒remove the light by pressing clip A-fig. 186 with a screw-
driver;
❒press the sides of bulb shield B-fig. 187 on the two fas-
tening pins and turn it;
❒replace the snap-fitted bulb C;
❒reposition the bulb shield by fitting the two fastening
pins;
175-210 PUNTO FL EN 4ed 20-01-2010 15:09 Pagina 197

F0U0170fig. 187
F0U0169mfig. 186
198
KNOWING
YOUR
VEHICLE
SAFETY
STARTING
AND DRIVING
WARNING LIGHTS
AND MESSAGES
IN AN
EMERGENCY
SERVICING
AND CARE
TECHNICAL
SPECIFICATIONS
CONTENTS
❒refit the light by first inserting side D-fig. 186 and then
pressing the other side until you hear the clip lock in-
to place.
F0U0171mfig. 188
CHANGING A FUSE
GENERAL INFORMATION
Fuses protect the electrical system: they cut in (i.e. they
blow) in the event of a fault or improper action on the sys-
tem.
Check the state of the corresponding fuse when a device
does not work: the filament A-fig. 188 must be intact. If it
is not, replace the blown fuse with a new one of the same
amperage (same colour).
B undamaged fuse
C fuse with damaged filament.
175-210 PUNTO FL EN 4ed 20-01-2010 15:09 Pagina 198

199
KNOWING
YOUR
VEHICLE
SAFETY
STARTING
AND DRIVING
WARNING LIGHTS
AND MESSAGES
IN AN
EMERGENCY
SERVICING
AND CARE
TECHNICAL
SPECIFICATIONS
CONTENTS
Never replace a blown fuse with metal
wires or other materials.
Should the fuse blow again, contact a Fi-
at Dealership.
WARNING
Never replace a fuse with one that has
a higher amperage: FIRE HAZARD.
WARNING
If a general protection fuse (MEGA-FUSE,
MIDI-FUSE, MAXI-FUSE) is activated,
contact a Fiat Dealership.
WARNING
Remove the key from the ignition and
switch off or disable all devices before re-
placing a fuse.
WARNING
If a general protection fuse for safety sys-
tems (air bag system, braking system),
power unit systems (engine system, transmission
system) or steering system is triggered, contact a
Fiat Dealership.
WARNING
175-210 PUNTO FL EN 4ed 20-01-2010 15:09 Pagina 199