FORD MUSTANG 1969 Volume One Chassis

07-01-10
General Transmission Service

07-01-10

2.
To adjust the switch for the park

position, place the transmission selec-

tor lever in 1 and push the park reset

button (Fig. 16) to the left (counter-

clockwise) until it stops.

3.
Check the operation of the

switch in each selector lever position.

The starter should engage in only the

neutral and park positions. Be sure to

perform
the
park reset
if for any rea-

son
the
neutral switch
is
adjusted.

If,
after performing
the
switch
ad-

justments,
the
starter still will
not en-

gage
in the
neutral
or
park positions,

replace
the
switch. Never replace
the

neutral switch until
the
switch adjust-

ments have been made.

SWITCH REPLACEMENT

1.
Disconnect the neutral start

switch wires at the plug connector.

2.
Disconnect the vacuum hoses, if

so equipped.

3.
Remove the two screws securing

the neutral start switch to the steering

column and lift the switch from the

column.

Check the column to be sure the

metal switch actuator is secure to the

shift tube and that it is seated as far

forward against the shift tube bearing

as is possible. Also check for a broken

or damaged actuator. If it is broken

or damaged, replace it as shown in

Figure 17.

4.
Before installing a new switch to

the column, check to see that the red

neutral position gauge inserted in the

neutral pinning hole. If the pin is

missing, align the two holes at the

neutral pinning hole on top of the

switch and install a No. 43 drill or

0.092-0.093 inch gauge pin.

5.
While holding the selector lever

against the stop in the neutral detent
ACTUATOR LEVER INSTALLED

WHEN INSTALLING
THE
ACTUATOR

LEVER
BE
SURE THAT
IT
1$ SEATED

AS
FAR
FORWARD AGAINST
THE
SHIFT

TUBE BEARING
AS IS
POSSIBLE.
FORWARD

D2019-A

FIG. 17—Removing
or
Installing Neutral Start Switch Actuator Lever

position, place the switch on the col-

umn and install the two attaching

screws. Tighten the screws to 20 in-lbs

torque.

6. Remove the gauge pin (or No.

43 drill if used).

7.
Connect the switch wires to the

plug connector and check for a start

in the neutral position. The starter

should engage with the selector lever

against the neutral stop. If not, loosen

the attaching screws and move the

switch just enough to engage the start-

er. Tighten the screws to 20 in-lbs tor-

que.

8. With the switch properly adjust-
ed in neutral, push the park reset but-

ton (Fig. 16) to the left (counterclock-

wise) until it stops. The park reset

must be performed whenever the

switch has been adjusted or replaced.

9. To adjust the switch for the park

position, place the transmission selec-

tor lever in 1 and push the park reset

button (Fig. 16) to the left (counter-

clockwise) until it stops.

10.
Connect the vacuum hoses to

the switch, if so equipped.

11.
Check the operation of the

switch in each selector lever position.

The starter should engage in only the

neutral and park detent positions.

NEUTRAL SWITCH-TYPE
A

(USED
ON
VEHICLES WITH VACUUM

OPFRATED PARKING BRAKE)
NEUTRAL SWITCH-TYPIE
B

(USED
ON
VEHICLES WITHOUT VACUUM

OPERATED PARKING BRAKE)

ATTACHING

FIG.
16—Ad
justing Neutral Switch—Column Shift
D2018-Aprocarmanuals.com

07-01-11
General Transmission Service

07-01-11

STOP
PIN

GROMMET

Tool - T67P-734LA

GROMMET

LEVER

CONTROL ROD REMOVAL
GROMMET INSTALLATION

Tool - T67P-734LA

r

CONTROL ROD INSTALLATION
3/16"-1/4'

CONTROL ROD

STOP
PIN

FIG. 18—Removing
or
Installing Shift Linkage Grommet
D 1742-A

MANUAL SHIFT LINKAGE

GROMMET REPLACEMENT-

COLUMN SHIFT

The manual lever assembly
on ve-

hicles equipped with
a
column shift
in-

corporates
an oil
impregnated plastic

grommet
in the end of the
lever
arm.

A special tool T67P-7341-A
is re-

quired
to
install
the
grommet
in the

manual lever,
and to
install
the
manu-

al linkage
rod
into
the
grommet.
Re-

move
and
install
the
grommet
as fol-

lows:

1.
Place
the
lower
jaw of the
tool

between
the
manual lever
and the con-

trol
rod.
Position
the
stop
pin
against
the
end of the
control
rod (Fig. 18)

and force
the rod out of the
grommet.

Remove
the
grommet from
the
manu-

al lever
by
cutting
off the
large shoul-

der with
a
sharp knife.
The
grommet

must
be
removed from
the
manual

lever
and a new one
installed each

time
the rod is
disconnected.

2.
Before installing
a
new grommet,

adjust
the
stop
pin to 1/2
inch
and

coat
the
outside
of the
grommet with

lubricant. Then, place
the
grommet
on

the stop
pin and
force
it
into
the
man-

ual lever hole. Turn
the
grommet
sev-

eral times
to be
sure
it is
properly

seated.

3.
Readjust
the
stop
pin to the
height shown
in Fig. 18. The pin

height
is
determined
by the
length
of

the
rod end
which
is to be
installed

into
the
grommet.
If the pin
height
is

not adjusted,
the
control
rod may be

pushed
too far
through
the
grommet

causing damage
to the
grommet
re-

taining
lip.

4.
With
the pin
height properly
ad-

justed, position
the
control
rod on the

tool
and
force
the rod
into
the
grom-

met until
the
groove
in the rod
seats

on
the
inner retaining
lip of the
grom-

met.
Be
sure
the rod
protrudes

through
the
grommet approximately

1/4 inch after installation.

CLEANING
AND
INSPECTION

CLEANING

TRANSMISSION

Clean
the
parts with suitable solvent

and
use
moisture-free
air to dry off all

the parts
and
clean
out oil
passages.

The composition clutch plates,

bands
and
synthetic seals should
not

be cleaned
in a
vapor degreaser
or
with
any
type
of
detergent solution.

To clean these parts, wipe them
off

with
a
lint-free cloth.
New
clutch

plates
or
bands should
be
soaked
in

transmission fluid
for
fifteen minutes

before
the
plates
or
bands
are as-

sembled.

CONVERTER

The converter cannot
be
disas-

sembled
for
cleaning.
If
there
is rea-
son
to
believe that
the
converter
con-

tains
an
excessive amount
of
foreign

material,
it
should
be
thoroughly

cleaned.
See the
instructions provided

with
the
Rotunda Automatic Trans-

mission Torque Converter
and
Cooler

Cleaner LRE-60081.

OIL COOLER

When
a
clutch
or
band failure
or

other internal trouble
has
occurred
inprocarmanuals.com

07-01-12
General Transmission Service

07-01-12

the transmission,
any
metal particles

or clutch plate
or
band material that

may have been carried into
the
cooler

should
be
removed from
the
system
by

flushing
the
cooler
and
lines before

the transmission
is put
back into serv-

ice.
In no
case should
an
automatic

transmission having
a
clutch
or
band

failure
or
other internal trouble result-

ing
in
fluid contamination,
be put

back into service without first flushing

the transmission
oil
cooler.

To flush
the oil
cooler, follow
the

instruct!
on >
provided with
the
Rotun-

da Automatic Transmission Torque

Converter
and
Cooler Cleaner
LRE-

60081.

INSPECTION

TURBINE
AND
STATOR
END

PLAY CHECK

A special tool
(Fig. 19)
must
be

used
to
check
the
condition
of the

converter. This special tool
is
used
to

check
the
turbine
and
stator
end
play

and
the
operation
of the
one-way
sta-

tor clutch.

CRUISE-O-MATIC

Too/-T58L-7902-A

C-4 AND C-6 TRANSMISSION

Tool-T59P.7902.Bor 7937-B

ON C-4 AND C-6 TRANSMISSION

Tool-T64L-7902-A
D
1499-E

FIG. 19—Converter Checking Tool

1.
Insert
the
tool (Fig.
19)
into
the

converter pump drive
hub
until
it
bot-

toms.

2.
Install
the
guide over
the con-

verter pump drive
hub.
3.
Expand
the
split fiber bushing
in

the turbine spline
by
tightening
the

adjusting
nut.
Tighten
the
adjusting

nut until
the
tool
is
securely locked

into
the
spline.

4.
Attach
a
dial indicator
to the

tool (Fig.
20 or
21). Position
the
indi-

cator button
on a
converter pump

drive
hub, and set the
dial face
at 0

(zero).

5.
Lift
the
tool upward
as far as it

will
go and
note
the
indicator reading.

The indicator reading
is the
total
end

play which
the
turbine
and
stator

share.
If the
total
end
play exceeds

the limits specified
in
Part 7-5, replace

the converter unit.

6. Loosen
the
adjusting
nut to
free

the split bushing,
and
then remove
the

tool from
the
converter.

STATOR ONE-WAY CLUTCH

CHECK

1.
Install
the
stator outer race hold-

ing tool
in one of the
four holes
pro-

vided
in the
stator (Fig.
20 or 21).

2.
Insert
the
tool
in the
converter

pump drive hub.
As the
tool enters
the

converter,
the
pins will engage
the sta-

tor clutch inner race spline.

3.
Place
a
torque wrench
on the

tool (Fig.
20 or
21).
The
tool (and
sta-

tor inner race) should turn freely

clockwise (from
the
pump drive
hub

inside
the
converter).
It
should lock
up

and hold
a 10
ft-lb pull when
the

wrench
is
turned counterclockwise.

Try
the
clutch
for
lockup
and
hold
in

at least five different locations around

the converter.
On
the
C4
or C6
Auto-

matics,
the
metal ring holding
the

locking tool will have
to be
held
by

hand during this check.

4.
If the
clutch fails
to
lock
up and

hold
a 10
ft-lb torque, replace
the

converter unit.

STATOR
TO
IMPELLER

INTERFERENCE CHECK

1.
Position
the
front pump assem-

bly
on a
bench with
the
spline
end of

the stator shaft pointing
up
(Fig.
22).

2.
Mount
a
converter
on the
pump

so that
the
splines
on the
one-way

clutch inner race engage
the
mating

splines
of the
stator support,
and the

converter
hub
engages
the
pump drive

gear.

3.
While holding
the
pump station-

ary, try
to
rotate the converter counter-

clockwise.
The
converter should
ro-

tate freely without
any
signs
of
inter-

ference
or
scraping within
the
convert-

er assembly.
4.
If
there
is an
indication
of
scrap-

ing,
the
trailing edges
of the
stator

blades
may be
interfering with
the

leading edges
of the
impeller blades.

In such cases, replace
the
converter.

STATOR
TO
TURBINE

INTERFERENCE CHECK

1.
Position
the
converter
on the

bench front side down.

2.
Install
a
front pump assembly
to

engage
the
mating splines
of
the
stator

support
and
stator,
and
pump drive

gear lugs.

3.
Install
the
input shaft, engaging

the splines with
the
turbine
hub (Fig.

23).

4.
While holding
the
pump station-

ary, attempt
to
rotate
the
turbine with

the input shaft.
The
turbine should
ro-

tate freely
in
both directions without

any signs
of
interference
or
scraping

noise.

5.
If
interference exists,
the
stator

front thrust washer
may be
worn,
al-

lowing
the
stator
to hit the
turbine.
In

such cases,
the
converter must
be re-

placed.

The converter crankshaft pilot

should
be
checked
for
nicks
or dam-

aged surfaces that could cause inter-

ference when installing
the
converter

into
the
crankshaft. Check
the con-

verter front pump drive
hub for
nicks

or sharp edges that would damage
the

pump seal.

OUTPUT SHAFT
AND

PRIMARY
SUN
GEAR SHAFT

(FMX TRANSMISSION)

1.
Inspect
the
thrust surfaces
and

journals
for
scores. Inspect
the
inter-

nal gear
for
broken
or
worn teeth.

2.
Inspect
the
aluminum sleeve
for

scores
or
leakage. Inspect
the
ring

grooves
for
burrs.

3.
Inspect
the
keyway
and
drive

ball pocket
for
wear,
and
inspect
the

splines
for
burrs, twist
or
wear.

4.
Inspect
the
output shaft sleeve

for alignment with
the
governor drive

ball (Fig.
24).

5.
Inspect
the
external parking gear

teeth
for
damage
and the
speedometer

drive gear teeth
for
burrs.

6.
If
either
the
output shaft
or
ring

gear
has
been replaced, place
the as-

sembled unit with
the
gear face down

on
the
bench, push
the
shaft down-

ward,
and
check
the
clearance
be-

tween
the top of the
snap ring
and its

groove
(Fig. 25).
If
this clearance
ex-

ceeds 0.002 inch, replace
the
snap ring

with
a
thicker ring
to
reduce
the
clear-

ance
to
less than 0.002 inch. Selectiveprocarmanuals.com

07-01-13

General Transmission Service

Tool -T59P-7902-C

or 7937-

(C4
and
C6)

STATOR CLUTCH INNER RACE

Split Fiber Bushing

END PLAY CHECK

Torque Wrench

Torque Wrench

Tool-T64L.790~2-A

C4 TRANSMISSION

STATOR CLUTCH CHECK

FIG. 20—Typical Converter Checking Tool—C4
and C6
Transmissions
D1842-Aprocarmanuals.com

07-01-14

General Transmission Service

07-01-14

STATOR CLUTCH INNER RACE

Splh Fiber Bushing

END PLAY CHECK

Torque
Wrench

Torque
Wrench

Tool -T58L-7902-B or 7946-A

TURBINE HUB

STATOR CLUTCH CHECK

D1934-A

FIG. 21—Typical Converter Checking Tool—FMX Transmissionprocarmanuals.com

07-01-15

General Transmission Service

07-01-15

GOVERNOR

DRIVE BALL

POCKET

FRONT PUMP AND STATOR

SUPPORT SHAFT

D1922-A

FIG. 22—Stator to Impeller

Interference Check

snap rings are available in several

thicknesses for this purpose.

7.
Inspect the rubber seal and stop

ring at the front of the output shaft

spline. If wear or damage is evident,

replace the parts.

8. Inspect the primary sun gear for

broken or worn teeth. Inspect all

thrust surfaces and journals for scores.

Check all fluid passages (Fig. 26) for

obstructions and leakage. Inspect the

seal ring grooves for burrs.

9. Inspect the sun gear shaft splines

for burrs and wear.

10.
Check the fit of the seal rings

in the grooves of the shaft. The rings

should enter the grooves freely with-

out bind.

11.
Check the fit of the seal rings

in their respective bores. If equipped

with cast iron seal rings, a clearance

of 0.002-0.009 inch should exist be-

tween the ends of the rings.

INPUT SHAFT

FRONT PUMP AND

STATOR SUPPORT

SHAFT

CONVERTER

ASSEMBLY

D1923-A
TEAR DROP

D1935-A

FIG. 24—Correct Position of

Output Shaft Aluminum Sleeve

D1936-A

FIG. 25—Checking Output

Shaft Snap Ring Clearance
12.
Install the seal rings on the

shaft, and check for free movement in

the grooves.

PINION CARRIER, ONE-WAY

CLUTCH AND CENTER

SUPPORT (FMX

TRANSMISSION)

1.
Inspect the clutch outer race,

inner race, band surface, pinion gears,

bearings, and thrust washer (Fig. 27)

for roughness.

2.
Inspect the center support bush-

ing for roughness.

3.
Inspect the one-way clutch cage

rollers and springs for excessive wear

or damage.

PINION CARRIERS (C4 or

C6 TRANSMISSIONS)

Individual parts of the planet car-

riers are not serviceable.

1.
The pins and shafts in the planet

assemblies should be checked for loose

fit and/or complete disengagement.

Use a new planet assembly if either

condition exists. Before installing a

planet assembly, the shaft retaining

pins should be checked for adequate

staking. If staking does not appear

adequate, the pins should be restaked

before installation. When restaking,

the retaining pins must not be driven

into the carrier any further than 0.040

inch below the surface of the carrier.

2.
Inspect the pinion gears for dam-

aged or excessively worn teeth.

3.
Check for free rotation of the

pinion gears.

EXTENSION HOUSING

1.
Inspect the housing for cracks.

Inspect the gasket surface for burrs or

warpage.

2.
Inspect the bushing for scores or

wear.

3.
Inspect the rear seal for hard-

ness,
cracks, or wear. If the seal

FRONT LUBRICATION REAR LUBRICATION

CLUTCH \ CLUTCH
LUBRICATION

FRONT CLUTCH

D1937-A

FIG. 23—Stator to Turbine

Interference Check
FIG. 26—Primary Sun Gear Shaft—Cross Sectional Viewprocarmanuals.com

07-01-16
General Transmission bervice
07-01-16

CENTER SUPPORT

PLANETARY CLUTCH
"CAM TYPE" CLUTCH RACE

CHAMFER ON PRODUCTION

PART, ONLY-SERVICE PART NOT CHAMFERED
PLANET CARRIER

D1938-A

FIG. 27—Roller Type Planetary Clutch, Carrier and Center Support

shows wear or deterioration, replace

the seal.

4.
Inspect the seal counterbore and

remove all burrs and scores with cro-

cus cloth.

REAR CLUTCH (FMX)

AND REVERSE-HIGH CLUTCH

(C4 AND C6 AUTOMATIC)

1.
Inspect the drum band surface,

the bushing, and thrust surfaces for

scores. Minor scores may be removed

with crocus cloth. Badly scored parts

must be replaced.

Inspect the clutch piston bore and

the piston inner and outer bearing sur-

faces for scores. Check the air bleed

ball valve in the clutch piston for free

movement. Check the orifice to make

sure it is not plugged.

2.
Check the fluid passages for ob-

structions. All fluid passages must be

clean and free of obstructions.

3.
Inspect the clutch plates for wear

and scoring and check the plates for

fit on the clutch hub serrations. Re-

place all plates that are badly scored,

worn or do not fit freely in the hub

serrations.

4.
Inspect the clutch pressure plate

for scores on the clutch plate bearing

surface. Check the clutch release

spring(s) for distortion.

5.
On an FMX transmission, in-

spect the needle bearing for worn rol-

lers.

FRONT CLUTCH (FMX)

AND FORWARD CLUTCH

(C4 OR C6

TRANSMISSIONS)

1.
Inspect the clutch cylinder thrust

surfaces, piston bore, and clutch plate
serrations for scores or burrs. Minor

scores or burrs may be removed with

crocus cloth. Replace the clutch cylin-

der if it is badly scored or damaged.

2.
Check the fluid passage in the

clutch cylinder for obstructions. Clean

out all fluid passages. Inspect the

clutch piston for scores and replace if

necessary. Inspect the piston check

ball for freedom of movement and

proper seating (Fig. 28).

CLUTCH

CYLINDER

PISTON

SEAL
CLIP

D1939-A

. 28—Clutch Piston Check

Valve

3.
Check the clutch release spring

for distortion and cracks. Replace the

spring if it is distorted or cracked.
4.
Inspect the composition and the

steel clutch plates and the clutch pres-

sure plate for worn or scored bearing

surfaces. Replace all parts that are

deeply scored.

5.
On FMX and C4 transmissions,

check the clutch plates for flatness

and fit on the clutch hub serrations.

Discard any plate that does not slide

freely on the serrations or that is not

flat.

6. Check the clutch hub thrust sur-

faces for scores and the clutch hub

splines for wear.

7.
On an FMX transmission, in-

spect the turbine shaft bearing sur-

faces for scores. If excessive clearance

or scores are found, discard the unit.

Check the splines on the turbine

shaft for wear and replace the shaft if

the splines are excessively worn. In-

spect the bushing in the turbine shaft

for scores. On a C4 or C6 Automatic

transmission, check the input shaft for

damaged or worn splines.

FRONT PUMP AND

STATOR SUPPORT

1.
Inspect the mating surfaces of

the pump body and cover for burrs.

2.
Inspect the drive and driven gear

bearing surface for scores, and check

the gear teeth for burrs. Inspect the

stator support splines for burrs and

wear.

3.
Check the fluid passages for ob-

structions.

4.
If any parts other than the stator

support are found defective, replace

the pump as a unit. Minor burrs and

scores may be removed with crocus

cloth. The stator support is serviced

separately.

5.
On a C4 or C6 Automatic trans-

mission, check the oil ring grooves in

the stator support for nicks, burrs or

damaged edges. On a C6 transmis-

sion, check the large seal ring groove

of the pump body for damage. Check

the gasket mating surface of the pump

body for damage.

REAR SUPPORT

(FMX TRANSMISSION)

1.
Inspect the gasket mating sur-

faces for damage.

2.
Inspect the support bushing for

scores.

3.
Inspect the rear support fluid

passages for obstructions.

4.
Check the fit of the fluid tubes in

the support.procarmanuals.com

07-01-17
General Transmission Service
07-01-17

PRESSURE REGULATOR

(FMX TRANSMISSION)

1.
Inspect the regulator body and

cover mating surface for burrs.

2.
Check all fluid passages for ob-

structions.

3.
Inspect the control pressure and

converter pressure valves and bores for

burrs and scores. Remove all burrs

carefully with crocus cloth.

4.
Check free movement of the

valves in their bores. The valves

should fall freely into the bores when

both the valve and bore are dry.

5.
Inspect the valve springs and

spacers for distortion.

CONTROL VALVE BODY

1.
Clean all parts thoroughly in

clean solvent, and then blow them dry

with moisture-free compressed air.

2.
Inspect all valve and plug bores

for scores. Check all fluid passages for

obstructions. Inspect the check valve

for free movement. Inspect all mating

surfaces for burrs or distortion. In-

spect all plugs and valves for burrs

and scores. Crocus cloth can be used

to polish valves and plugs if care is

taken to avoid rounding the sharp

edges of the valves and plugs.

3.
Inspect all springs for distortion.

Check all valves and plugs for free

movement in their respective bores.

Valves and plugs, when dry, must fall

from their own weight in their respec-

tive bores.

4.
Roll the manual valve on a flat

surface to check it for a bent condi-

tion.

GOVERNOR

1.
Inspect the governor valves and

bores for scores. Minor scores may be
removed from the valves with crocus

cloth. Replace the governor if the

valves or body is deeply scored.

2.
Check for free movement of the

valves in the bores. The valves should

slide freely of their own weight in the

bores when dry. Inspect fluid passages

in the valve body and counterweight

for obstructions. All fluid passages

must be clean.

3.
Inspect the mating surfaces of

the governor body and governor dis-

tributor (C4 or C6 Automatic) for

burrs and distortion. Mating surfaces

must be smooth and flat.

4.
Check the mating surface of the

governor valve and the counterweight

on a FMX transmission for burrs or

scratches.

5.
When cleaning the governor as-

sembly (C4 Automatic), the oil screen

should be removed from the collector

body and thoroughly blown out with

compressed air.

FRONT SERVO (FMX)

AND INTERMEDIATE

SERVO (C4 AND C6

AUTOMATIC)

1.
Inspect the servo bore for cracks

and the piston bore and the servo pis-

ton stem for scores. Check fluid pas-

sages for obstructions. Replace seals

that are damaged.

2.
On an FMX transmission, check

the actuating lever for free movement,

and inspect it for wear. If necessary to

replace the actuating lever or shaft,

remove the retaining pin and push the

shaft out of the bracket.

Inspect the adjusting screw threads

and the threads in the lever for dam-

age.

3.
Check the servo spring and servo

band strut(s) for distortion.

4.
Inspect the cover seal and gasket

cover sealing surface for defects.
REAR SERVO (FMX)

AND LOW-REVERSE SERVO

(C4 TRANSMISSION)

1.
Inspect the servo body for cracks

and the piston bore for scores.

2.
Check the fluid passages for ob-

structions.

3.
Inspect the band and the struts

for distortion. Inspect the band ends

for cracks.

4.
Inspect the servo spring for dis-

tortion.

5.
Inspect the band lining for exces-

sive wear and bonding to the metal

band.

6. On an FMX transmission, check

the servo body to case mating surface

for burrs. Check the accumulator pis-

ton and the check valve for freedom

of movement. Check the actuating

lever socket for scores.

7.
Replace seals that are damaged.

CASE

Inspect the case for cracks and

stripped threads. Inspect the gasket

surfaces and mating surfaces for

burrs.
Check the vent for obstructions,

and check all fluid passages for ob-

structions and leakage (Figs. 10, 11

and 12).

Inspect the case bushing for scores.

Check all parking linkage parts for

wear or damage.

ONE-WAY CLUTCH

1.
Inspect the outer and inner races

for scores or damaged surface area

where the rollers contact the races. If

the outer race on the C6 transmission

is damaged, the low-reverse clutch hub

must be replaced.

2.
Inspect the rollers and springs

for excessive wear or damage.

3.
Inspect the spring and roller case

for bent or damaged spring retainers.procarmanuals.com

07-02^01

C4 Automatic Transmission
0702-01

PART 7-2 C4 Automatic
Transmission

PEA-A2 240-1V Column

PEA-MI 302-2V Column

PEA-N1 3O2-2V Console

PEB-B2 200-1V Console

PEB-C2 17O-1V,2OO-1V Column

PEE-M 302-2V Console

PEE-V 302-2V Column

PEE-AC 302-2V Console

PEE-AD 250-1V Console

PEE-AE 250-1V Column

PEE-AF 250-1V Console
MODEL APPLICATION
All
Models
Ford

X

X

X
Mercury
X

X

X
Meteor
Cougar
Fairiane

X

X

X

X
Falcon
X

X
Montego
X

X

X

X
Mustang
X

X

X
Lincoln-
Continental
Thunderbird
Continental-
Mark
III

COMPONENT INDEX

ASSEMBLY OF TRANSMISSION

BAND ADJUSTMENTS

Intermediate Band

Low-Reverse Band

CONTROL VALVE BODY

Cleaning and Inspection

Disassembly and Overhaul

Removal and Installation

DESCRIPTION

DISASSEMBLY AND OVERHAUL OF

TRANSMISSION

End Play Check

DOWNSHIFT LINKAGE

Adjustments

Parts Repair or Replacement

EXTENSION HOUSING

Cleaning and Inspection

Removal and Installation

EXTENSION HOUSING BUSHING

Removal and Installation

EXTENSION HOUSING REAR SEAL

Removal and Installation

FORWARD CLUTCH

Cleaning and Inspection

Disassembly and Overhaul

FORWARD CLUTCH HUB AND RING

GEAR

Disassembly and Overhaul

FRONT PUMP

Cleaning and Inspection

Disassembly and Overhaul

All
Models
02-27

02-09

02-09

01-16

02-19

02-11

02-02

02-12

02-12

02-04

02-17

01-14

02-10

02-10

02-10

01-15

02-24

02-25

01-15

02-21
COMPONENT INDEX

GOVERNOR AND OIL DISTRIBUTOR

Cleaning and Inspection

Disassembly and Overhaul

Removal and Installation

INTERMEDIATE SERVO

Cleaning and Inspection

Parts Repair or Replacement

Removal and Installation

INPUT SHELL AND SUN GEAR

Disassembly and Overhaul

LOW-REVERSE BRAKE DRUM BUSHING

Disassembly and Overhaul

LOW-REVERSE SERVO

Cleaning and Inspection

Parts Repair or Replacement

LOW-REVERSE SERVO PISTON

Removal and Installation

MANUAL LINKAGE

Adjustments

Parts Repair or Replacement

NEUTRAL START SWITCH-CONSOLE

SHIFT

Adjustment

Removal and Installation

(Refer to Part 7-1 for Column Shift Adjus

ment and Removal and Installation Pro-

cedures)

OIL PAN

Removal and Installation

REVERSE-HIGH CLUTCH

Cleaning and Inspection
All
Models
01-16

02-26

02-10

01-16

02-16

02-09

02-25

02-26

01-16

02-16

02-09

02-04

02-17

02-04

02-07

02-09

01-15
procarmanuals.com

J7-02-02
C4 Automatic Transmission
07-02-02

COMPONENT INDEX

Disassembly and Overhaul

REVERSE RING GEAR AND HUB

Disassembly and Overhaul

SELECTOR LEVER-CONSOLE SHIFT

Removal and Installation

THROTTLE LINKAGE
All
Models
02-22

02-26

02-08
COMPONENT INDEX

Adjustments

TRANSMISSION (Complete)

Removal and Installation

TRANSMISSION CASE BUSHING

Parts Repair or Replacement

TRANSMISSION CASE THREAD REPAIR
All
Models
02-04

02-11

02-18

02-18

DESCRIPTION

CONVERTER HOUSING,

CONVERTER
STATOR SUPPORT

FRONT PUMP CASE

INTERMEDIATE

BAND

LOW-REVERSE DRUM
-,

FORWARD CLUTCH

HUB AND RING GEAR

INPUT

SHELL
REVERSE RING GEAR

LOW REVERSE BAND

ONE-WAY

CLUTCH
GOVERNOR

DISTRIBUTOR

SLEEVE

GOVERNOR

DISTRIBUTOR

SPLINE SEAL

EXTENSION

HOUSING

SPEEDOMETER

DRIVE GEAR

GOVERNOR

REVERSE PLANET CARRIER

FRONT PLANET CARRIER

PARK TOGGLE LEVER

LOW-REVERSE SERVO PISTON

FORWARD CLUTCH

CONTROL LEVERS

FIG.
1—C4
Automatic Transmission

DESCRIPTION

Figure
1
shows
the
location
of the

converter, front pump, clutches, gear

train
and
most
of the
internal parts

used
in
the C4 transmission. The iden-

tification
tag
(Fig.
2) is
located under

the lower front intermediate servo

cover bolt.
The tag
shows
the
model

prefix
and
suffix, assembly part num-

bers,
and the
built date code.
The

service identification number indicates

changes
to
service details which affect

interchangeability when
the
transmis-

sion model
is not
changed.
For
inter-

pretation
of
this number, see the Mas-

ter Parts Catalog.
REVERSE-HIGH CLUTCH

IMPELLER CONTROL VALVE BODY

TRANSMISSION MODEL
D 1474-A

ASSEMBLY PART NO. BUILD DATE

FIG.
2—Identification
Tag

The
C4
transmission
is a
three

speed unit capable
of
providing auto-

matic upshifts
and
downshifts through
SHIFT

D1846-A

the three forward gear ratios,
and
also

capable
of
providing manual selection

of first
and
second gears.
procarmanuals.com