differential FORD MUSTANG 1969 Volume One Chassis

04-02-17
Rear Axle
—
Removable Carrier Type
04-02-17

Too/-T53L-200-A

L-462S-A

4625-K
or
4625-KA

>:
M
E 1726-A

FIG. 36—Installing Pilot Bearing

loaded
to
seat
the
bearings
in
their

cups.
This step
is
important.

5. Again loosen the- right
nut to re-

lease
the
preload. Check
to see
that

the left
nut
contacts
the
bearing
cup.

Using
the
dial indicator set-up shown

in Fig.
10,
Part 4-1, adjust the preload

to 0.008
to
0.012 case spread
for new

bearings
or
0.005
to
0.008
for the ori-

ginal bearings,
if
re-used.

6. Check
the
runout
of
the differen-

tial case flange with
a
dial indicator.

If
the
runout does
not now
exceed

specifications, install
a new
ring gear.

If
the
runout still exceeds specifica-

tions,
the
ring gear
is
true
and the

trouble
is due to
either
a
defective

case
or
worn bearings.

7. Remove
the
differential case

from
the
carrier
and
remove
the
side

bearings from
the
case.

8. Install
new
bearings
on the
case

hubs,
and
again install
the
differential

assembly
in the
carrier without
the

ring gear.

9. Check the case runout again with

the new bearings.
If the
runout
is
now

within limits,
the old
bearings were

excessively worn.
Use the new
bear-

ings
for
assembly.
If the
runout
is
still

excessive,
the
case
is
defective
and

should
be
replaced.
Press,
Ram

REAR BEARING

CONE
AND

ROLLER

Too/-

T57L-46U-A
Fiber B/oc.

DRIVE

PINION

Too/-

T57L-4621-B

1701-A

FIG. 37—Installing Pinion Rear

Bearing Cone

PRESS RAM

Tool - 4621
L

E1903A

FIG. 38—Installing Pinion Rear

Bearing Cone

ASSEMBLY
OF
DIFFERENTIAL

CARRIER

PILOT BEARING

INSTALLATION

1.
Drive
the new
pilot bearing
in-

ward until
it
bottoms,
as
shown
in

Fig.
36.

2.
Using
the
same tool indicated
in

Fig.
36,
install
the new
pilot bearing

retainer with
the
concave side
up.
COLLAPSIBLE PINION

BEARING SPACER

INSTALLATION

1.
Install
the
drive pinion rear bear-

ing cone and roller
on the
pinion shaft

(Figs.
37
m 38).

Place
a new
spacer
on the
pinion

shaft (Fig.
39).

2.
Place
the
bearing retainer
on the

pinion shaft,
and
install
the
front

bearing cone
and
roller. Press
the

front bearing cone and roller into posi-

tion
as
shown
in Fig. 40. Be
careful

not
to
crush
the
bearing spacer.

3.
Lubricate
the
O-ring with axle

lubricant and install
it in its
groove
in

the pinion retainer.
Be
careful
not to

twist
it.
Snap
the
O-ring into position.

4.
Place
the
proper shim
on the

carrier housing
and
install
the
pinion

and retainer assembly, being careful

not
to
pinch
the
O-ring (Fig.
41).

5. Install
the
pinion attaching bolts.

Torque
the
bolts
to
specification.

6. Place
the
slinger over
the
pinion

shaft
and
against
the
front bearing.

7.
Install
a new
seal
in the
bearing

retainer (Fig.
47).

8. Install
the
U-joint flange
(Fig.

49).

9. Start
a new
integral
nut and

washer
on the
pinion shaft.

Press
Ram

L*
Fiber Block

Tool-

T57L-4621

E 1712-A

FIG. 40—Installing Pinion Front

Bearing

FLANGE
O-RING

REAR BEARING

SPACER

SEAL
FRONT BEARING

RETAINER
SHIM
PINION

FIG. 39—Pinion
and
Bearing Retainer
PILOT

BEARING

RETAINER

PILOT

BEARING

E 1782-Aprocarmanuals.com

04-02-19
Rear Axle — Removable Carrier Type
04-02-19

POINTER RESTING ON

PINION NUT

E 1505-B

FIG.
44
— End Play Indicator

Installation

pinion shaft as shown in Figs. 37 and

38.

2.
Slide the correct spacer over the

pinion shaft against the rear bearing.

3.
Position the bearing retainer and

cup assembly on the pinion shaft and

install the front bearing cone and rol-

ler. Press the front cone and roller

into position, as shown in Fig. 46.

4.
Lubricate a new O-ring with axle

lubricant and install it in the groove

provided in the pinion retainer. Be

careful not to twist the O-ring. Install

it by snapping it into place.

5.
Place the proper shim on the

carrier housing and install the pinion

and retainer assembly, being careful

not to pinch the O-ring (Fig. 41).

6. Install the pinion retainer bolts.

Torque the bolts to specification.

7.
Place the slinger over the pinion

shaft and against the front bearing.
Tool - 4858-
E

E 1197-D

FIG. 46—Installing
U-Joint
Flange

8. Install a seal in the bearing re-

tainer, (Fig. 47).

9. Start a new integral nut and

washer on the pinion shaft.

10.
Hold the companion flange with

the tool shown in Fig. 20 or 22 and

torque the pinion nut to specifications

(200 ft-lbs).

11.
With a new seal installed pin-

ion bearing preload should now read

17 to 32 in-lbs for new pinion bearings

and new seal, or 8 to 14 in-lbs for ori-

ginal bearings and a new seal.

ASSEMBLY AND

INSTALLATION OF

DIFFERENTIAL CASE

Conventional

Differential Case

1.
Place a side gear and thrust

washer in the differential case bore

E 1506-B

E 1629-A

FIG. 45— Checking Pinion End

Play
FIG. 47—Installing Oil Seal
(Fig. 48). Lubricate all differential

parts liberally with axle lubricant dur-

ing assembly.

2.
With a soft-faced hammer, drive

the differential pinion shaft into the

case only far enough to retain a pin-

ion thrust washer and pinion gear.

3.
Place the second pinion and

thrust washer in position, and drive

the pinion shaft into place. Carefully

line up the pinion shaft lock pin holes.

4.
Place the second side gear and

thrust washer in position (Fig. 48),

and install the cover on the differen-

tial case. Install the pinion shaft lock

pin. A pinion or axle shaft spline can

be inserted in the side gear spline to

check for free rotation of the differen-

tial gears.

5.
Insert two 7/16 (N.F.) bolts two

inches long through the differential

case flange, and thread them three or

four turns into the ring gear as a

guide in aligning the ring gear bolt

holes.
Press or tap the ring gear into

position.

6. Install and tighten the ring gear

bolts and washers evenly, and torque

them alternately across the gear to

specification.

7.
If the differential bearings have

been removed, press them on as

shown in Figs. 49 and 50.

8. Wipe a thin coating of lubricant

on the bearing bores so that the dif-

ferential bearing cups will move easily.

9. Place the cups on the bearings.

If the gear set is of the non-hunting or

partial non-hunting type, assemble the

differential case and ring gear assem-

bly in the carrier so that the marked

tooth on the pinion indexes between

the marked teeth on the ring gear as

shown in Fig. 51.

In almost every case of improper

assembly (gears assembled out of

time),
the noise level and probability

of failure will be higher than they

would be with properly assembled

gears.

When installing the hunting type

gear set (no timing marks), assemble

the differential case and ring gear as-

sembly in the carrier without regard

to the matching of any particular gear

teeth.

10.
Slide the assembly along the

bores until a slight amount of back-

lash is felt between the gear teeth.

11.
Set the adjusting nuts in the

bores so that they just contact the

bearing cups. The nuts should be en-

gaged about the same number of

threads on each side.

12.
Carefully position the bearing

caps on the carrier. Match the marks

made when the caps were removed.procarmanuals.com

04-02-20
Rear Axle — Removable Carrier Type

0402-20

THRUST WASHER

E1175-B

FIG. 48—Assembling Differential Case

13.
Install the bearing cap bolts

and alternately torque them. The 9

3/8 inch ring gear size axle requires

60-70 ft-lbs. The 8 3/4 inch and 9

inch ring gear size axles require 70-85

ft-lbs.

14.
If the adjusting nuts do not turn

freely as the cap bolts are tightened,

remove the bearing caps and again in-

spect for damaged threads of incor-

rectly positioned caps. Tightening the

bolts to the specified torque is done to
be sure that the cups and adjusting

nuts are seated. Loosen the cap bolts,

and torque them to only 25 ft. lbs be-

fore making adjustments.

15.
Adjust the backlash between the

DIFFERENTIAL

BEARING

CONE AND

ROLLER

E 1700-A

FIG. 49—
Installing
Differential

Bearing
1376-A

FIG. 50—Installing Differential

bearing
ring gear and pinion as outlined in

Part 4-1, Section 2.

16.
Be sure to make a final tooth

pattern check before installing the

carrier assembly in the axle housing.

Limited-Slip

Differential Case

1.
Place the inner side gear and

thrust washer in the differential case

(Fig. 52). Lubricate all parts liberally

with limited-slip axle lubricant during

assembly.

2.
With a soft-faced hammer, drive

the pinion shaft into the case only far

enough to retain a pinion thrust wash-

er and pinion gear.

3.
Place the second pinion and

thrust washer in position and drive

the pinion shaft into place. Carefully

line up the pinion shaft lock in holes.

4.
Install the pinion shaft lock pin.

The lock pin must not extend beyond

the surface of the case.

5. Insert two 2-inch 7/16 (NF)

bolts through the differential case

flange, and thread them three or four

turns into the ring gear as a guide in

aligning the ring gear bolt holes. Press

or tap the ring gear into position.

6. Clamp the differential case in a

soft-jawed vise. Install the differential

outer side gear on the differential pin-

ion gears. Place the clutch hub on

the side gear. Place the thrusi: washer

on the huh

Limited-Slip dutch

Plate Installation

Prior to clutch plate installation,

the friction bonded plates must be

soaked in C6AZ-19570-C (ESW-

M2C-104-A) differential lubricant for

approximately 1/2 hour. In addition,

the differential lubricant must be lib-

erally applied to all components to

be assembled.

1.
Place the clutch hub into posi-

tion in a soft-jawed vise.

2.
First, install a steel clutch plate

in the cavity of the differential case

opposite the ring gear and then a

bonded friction plate (Fig. 53). Any

tab on the steel plates can be inserted

into any cavity in the differential case,

however when the first steel plate is

inserted the others must be placed in

the same manner (Fig. 54) so the tabs

with slots line up. Install the remain-

ing plates: a steel plate, bonded fric-

tion plate, a steel plate, bonded fric-

tion plate and lastly a steel plate.

Make sure the bonded friction plate

inner-spline teeth properly engage the

hub spline.procarmanuals.com

04-02-21
Rear Axle
—
Removable Carrier Type
04-02-21

SITION IN WHICH GEARS WERE LAPPED

FIG. 51—Gear
Set
Timing Marks

3.
Center
the
Belleville spring
on

the clutch pack (spring concave-side

facing downward
on the
pack)
to pre-

vent trapping
the
spring between
the

left
and
right handcase
in an
eccentric

position
(Fig. 54).
Improper location

of
the
Belleville spring will cause
ex-

tremely high torque
and
differential

chatter.
Be
sure
the
slots
in the
rabbit

ears
of the
steel plates
are in
proper

alignment.

4.
Carefully
set the
differential case

cover over
the
right hand case
(Fig.

55).
At
this point,
no
force
or
pressure

should
be
applied
to the
cover.
The

cover contains
two 3/16
inch holes
by

which
the
clutch plates
can be
proper-

ly aligned. Insert
the
shank ends
of
two
1/8
inch drill bits into
the
holes,

and work
the
drill bits back-and forth

until
the
plates
are
centered
(Fig. 55).

When
the
clutch plates
are
centered,

the weight
of the
cover will cause
it to

fall into position. Remove
the
drill

bits.

5.
Install
the
ring gear
to
differen-

tial case bolts,
and
tighten them even-

ly
and
alternately across
the
diameter

of
the
ring gear. Tighten
the
bolts
to

specification.

6. Prior
to
installation
of the

limited-slip differential into
the ve-

hicle,
a
differential torque check must

be made. Check
the
torque required
to

rotate
one
side gear while
the
other

side gear
is
held
(Fig. 56). The
initial

PINION GEAR

DIFFERENTIAL

CASE
_
LUBRICATOR

HOLE / CLUTCH HUB

THRUST /

PINION \\WASHERS/

SHAFT
BELLEVILLE SPRING

STEEL
PLATE.

BONDED PLATES

CASE COVER

STEEL PLATES

RING GEAR
SIDE GEARS

LOCK
PIN

E 1738-A
STEEL PLATE THRUST WASHER

E 1189-

FIG. 53—Installing Steel Clutch

Plates
and
Friction Plates

BELLEVILLE SPRING

E 1711-A

FIG.
54
— Belleville
Spring

Installation

breakaway torque required
to
start
the

side gear turning
may
exceed
300 ft-

lbs.
Observe only
the
torque required

for continuous even rotation. There

should
be no
abnormal roughness
or

binding.
In
some instances
the
rotat-

ing torque
may
reach
250
ft-lbs, this

condition
is
acceptable,
if
rotation
is

smooth.
If the
results
of the
bench

check
are not
within specified limits,

internal trouble
may be
present
and

should
be
corrected before installing

the assembly
in the
vehicle. Some

possible torque problems
as
follows:

1/8" DRILL

DIFFERENTIAL

CASE COVER

E 1191-C

FIG. 52—Limited-Slip Differential Assembly
FIG.
55—
Differential Cover

Installationprocarmanuals.com

04-02-22

Rear Axle — Removable Carrier Type
04-02-22

Too/-T59L-4204-A

or
44211

and
44211-A

EH92-C

FIG. 56—Checking Differential

Torque

High Torque

a. Insufficient lubricant on the

clutch plates.

b.
A clutch plate wedged in be-

tween the case halves.

c. An improperly centered Belleville

spring.

Low Torque

a. Weak Belleville spring.
b.
Improper amount of clutch

plates installed.

Under no circumstances should the

Belleville spring be ground down to

reduce torque. The torque required to

keep the side gear turning with new

clutch plates is 155 to 195 ft-lbs. On

reused clutch plates, the torque re-

quired is 75 ft-lbs minimun.

7.
If the differential bearings have

been removed, press them on as

shown in Figs. 49 and 50.

8. Install the side bearings on the

differential case, and install the case

in the carrier as described in steps 7

through 16 under Assembly and In-

stallation of Conventional Differential

Case. Adjust and check backlash be-

tween the ring gear and pinion as di-

rected under Differential Bearing Pre-

load Adjustments.

ASSEMBLY OF

TRACTION-LOK

DIFFERENTIAL CASE

1.
Lubricate all parts with Ford

Hypoid Lubricant (Ford Part No.

C6AZ-19580-C), during assembly of

differential.

2.
Mount the differential case in a

soft jawed vise and place a side gear

thrust washer and side gear in the

counterbore of the case.

CENTER BLOCK

PRELOAD SPRINGS

PRELOAD PLATE

PINION GEAR

DIFFERENTIAL CASE

E1893-
A

. 57—Center Block and Pre-Load Springs Installation
3.
Install the pinion thrust washers

and place the pinion gears on the side

gear; aligning the holes in the washers

and gears with the holes in the case.

4.
Install the center block so that

the shaft holes are aligned with the

holes in the pinion gears and case.

The center block has two machined

sides and two rough sides.

5.
With a brass drift, drive in the

long pinion shaft from the outside of

the case aligning the lock pin holes in

the shaft with the holes in the case.

The center block should be positioned

so the long shaft is driven through the

rough side and short shafts driven

through the machined side (Fig. 57).

6. With a suitable drift, install the

shaft lock pins. Make sure the pinion

and side gears move freely.

7.
Place the four pre-load springs in

the holes provided in the center block.

8. Position a pre-load plate over the

four springs, making sure the springs

are properly seated. The pre-load

plate straddles the center block over

its narrower or machined width.

9. Mount the differential cover in a

soft jawed vise or holding fixture.

10.
Insert shim(s) of 0.050 total

thickness in the cover cavity.

11.
Install the composite plate (fric-

tion material on one side and steel on

the opposite) on the back side of the

clutch hub with the friction material

against the hub; next, install a friction

plate, then steel, friction, stee, fric-

tion, steel, friction, and lastily a steel

plate (Figures 3 and 58). When new

clutch plates are used, soak the plates

in Ford Hypoid Lubricant (Ford Part

No.
C6AZ-19580-C), or equivalent lu-

bricant, for approximately 30 minutes

before installation.

12.
Place the clutch hub with the

clutch plates into the clutch ear cavi-

ties in the differential cover. Make

sure that the splines on the last fric-

ion plate are engaged on the hub.

13.
Obtain locally a 5/8 inch x

2 1/2 inch or 9/16 inch x 2 1/2

inch bolt, nut and two I 1/2 inch

outside diameter flat washers approx.

1/8 inch in thickness. These parts are

required to compress the clutch pack

in order to obtain the proper shim

selection.

Install a flat washer on the bolt,

and place the bolt through the clutch

hub.
Hold the bolt in position and

turn the cover over. Place a flat wash-

er on the bolt and then install the nut.

Be sure the washers are centered, and

torque the nut 10 to 15 ft-lbs (Fig.

59).

14.
Place the shim template tool

(Ford Tool No. T68P-4946-A) in the

clutch hub. Some clearance should beprocarmanuals.com

04-02-23
Rear Axle — Removable Carrier Type

04-02-23

observed between the shim tool and

the cover-to-case mating surface.

Using a feeler gauge, determine the

exact amount of clearance. Refer to

the shim pack thickness chart specifi-

cations which will indicate the correct

amount of shim(s) to subtract from

the 0.050 shim originally installed. In

order to correctly select the proper

shim(s), the shim template tool and

the chart must be used.

15.
After the proper shim selection

is determined, remove the bolt, nut

and flat washers. If it is necessary to

revise the shim thickness, remove the

clutch hub and clutch plates.

16.
Install the selected shim(s) in

the cover cavity, reinstall the compo-

nents as outlined in Steps 11 and 12.

17.
Install the four steel clutch ear

guides and side gear.

18.
Place both assemblies in a

press,
and press the two halves togeth-

er; then, insert the two Allen or Phil-

lips head screws, and tighten evenly

until tight. If a press is not available,

any two stock bolts and nuts may be

used opposite each other in the ring

gear retaining holes to compress both

halves.

19.
Install the ring gear and ring

gear bolts and washers. Tighten evenly

and alternately across the diameter of

the ring gear. Torque the bolts to

65-80 ft-lbs.

20.
Prior to installation of the tor-

que sensitive locking differential into a

vehicle, a bench torque check must be

made. Check the torque required to

rotate one side gear while the other is

held stationary (Fig. 56). The initial

break-away torque may exceed 250

ft-lbs.
The rotating torque required to

keep the side gear turning with new

clutch plates is 100 to 250 ft-lbs. With

re-used clutch plates, the minimum

torque required is 40 ft-lbs. (The tor-

que may fluctuate 10-40 ft-lbs.).
DIFFERENTIAL COVER

SHIM
-COMPOSITE PLATE

CLUTCH HUB

SIDE GEAR

FRICTION PLATES

E1894-A

FIG. 58— Clutch Pack Installation

CLEARANCE CHECK AREA

SHIM TEMPLATE

E1895-A

59—Shim Template Tool Applicationprocarmanuals.com

04-03-01

Rear Axles — Integral Carrier Type

04-03-01

PART 4-3 Rear Axles-Integral Carrier Type

(Except Ford Light Duty
WER
Axle)

COMPONENT INDEX

AXLE HOUSING

Cleaning and Inspection

Removal and Installation

AXLE SHAFT

Cleaning and Inspection

Removal and Installation

CONVENTIONAL DIFFERENTIAL CASE

Cleaning and Inspection

Disassembly and Overhaul

Removal and Installation

DIFFERENTIAL BEARINGS AND RING

GEAR

Cleaning and Inspection

Removal and Installation

LIMITED SLIP DIFFERENTIAL CASE

Disassembly and Overhaul

PINION AND RING GEAR

Cleaning and Inspection

Removal and Installation

PINION BEARING CUPS

Cleaning and Inspection

Removal and Installation

PINION OIL SEAL

Removal and Installation

REAR WHEEL BEARINGS AND SEALS

Cleaning and Inspection

Removal and Installation

U-JOINT FLANGE

Cleaning and Inspection

Removal and Installation
MODEL APPLICATION
All
Models

01-09

01-10

01-10

01-10

01-10

01-10

01-10

01-10
Ford
N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A
Mercury
N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A
Meteor
N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A
Cougar
03-06

03-02

03-08

03-07

03-08

03-08

03-09

03-08

03-04

03-02

03-05
Fairlane
03-06

03-02

03-08

03-07

03-08

03-08

03-09

03-08

03-04

03-02

03-05
Falcon
03-06

03-02

03-08

03-07

03-08

03-08

03-09

03-08

03-04

03-02

03-05
Montego
03-06

03-02

03-08

03-07

03-08

03-08

03-09

03-08

03-04

03-02

03-05
Mustang
03-06

03-02

03-08

03-07

03-08

03-08

03-09

03-08

03-04

03-02

03-05
Lincoln-
Continental
N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A
Thunderbird
N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A
Continental-
Mark
III
N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

A page number indicates that the item is for the vehicle listed at the head of the column.

N/A indicates that the item is not applicable to the vehicle listed.

DESCRIPTION

The rear axle assembly is an integral-

type housing, hypoid design, with the

centerline of the pinion set below the

centerline of the ring gear (Fig. 1).

The semi-floating axle shafts are re-

tained in the housing by ball bearings

and a bearing retainer at the axle hous-

ing outer ends.

The differential assembly is mount-

ed on two opposed tapered roller
bearings. The bearings are retained in

the housing by removable caps. Dif-

ferential bearing preload and drive

gear backlash is adjusted by nuts lo-

cated behind each differential bearing

cup.

The drive pinion assembly is mount-

ed on two opposed tapered roller

bearings. Pinion bearing preload is

adjusted by a collapsible spacer on the
pinion shaft. Pinion and ring gear

tooth contact is adjusted by shims be-

tween the rear bearing cone and

pinion gear.

A cover on the rear of the differen-

tial housing provides access for inspec-

tion and removal and installation of

the differential assembly and drive

pinion.
procarmanuals.com

04-03-02
Rear Axles — Integral Carrier Type

04-03-02

RING GEAR

4209

DRIVE PINION

BEARINGS

4630

4621
FLANGE-4676

E1905A

FIG. 7—Typical Rear Axle Assembly

IN-VEHICLE ADJUSTMENT
AND
REPAIR

REAR AXLE SHAFT, WHEEL

BEARING
AND OIL
SEAL

REPLACEMENT

Synthetic wheel bearing seals
are

used
for
production purposes only.

>Tool-T60K-4234-A

or 4235-D

Tool-T50T-W0-A
or 8-/66

* El904A

FIG. 2—Removing Axle Shaft

E 1731-A

FIG. 3—Removing Rear Wheel

Bearing Retainer Ring
Removal
and
insertion
of
rear axle

shafts must
be
performed with
cau-

tion.
The
entire length
of the
shaft
(in-

cluding spline)
up to the
seal journal

must pass through
the
seal without

contact.
Any
roughing
or
cutting
of

the seal element during axle removal

or installation will result
in
early seal

failure. Leather seals only will
be
used
as service replacements
for
synthetic

wheel bearing seals.

The rear axle shafts, wheel bear-

ings,
and oil
seal
can be
replaced

without removing
the
differential
as-

sembly from
the
axle housing.
Re-

moval
of the
wheel bearings from
the

axle shafts make them unfit
for fur-

ther
use.

E1421-B

FIG. 4—Removing and Installing Rear Wheel Bearing—

Montego—Cougarprocarmanuals.com

04-03-06

Rear Axles — Integral Carrier Type

04-03-06

9. Install a new integral nut and

ivasher on the pinion shaft. (Apply a

small amount of lubricant on the

washer side of the nut.)

10.
Hold the flange with the tool

shown in Fig. 9 while the nut is being

tightened.

11.
Tighten the pinion shaft nut,

rotating the pinion occasionally to in-

sure proper bearing seating, (Fig. 6)

and take frequent preload readings

until the preload is at the original rec-

orded reading established in step 3.

12.
After original preload has been

reached, tighten the pinion nut slowly,
until an additional preload of 6 to 12

in-lbs has been added.

The preload should not exceed the

amount shown above, or bearing fail-

ure may result.

Under no circumstances should the

pinion nut be backed off to lessen pre-

load. If this is done, a new pinion

bearing spacer must be installed. (In

addition, the U-joint flange must

never be hammered on, or pneumatic-

-tools used.)

13.
Remove the oil seal replacer

tool from the transmission extension
housing. Install the front end of the

drive shaft on the transmission output

shaft.

14.
Connect the rear end of the

drive shaft to the axle U-joint flange,

aligning the scribe marks made on the

drive shaft end yoke and the axle U-

joint flange (Fig. 14).

15.
Check the lubricant level. Make

sure the axle is in running position.

Add whatever amount of specified lu-

bricant is required to reach the lower

edge of the filler plug hole, located in

the carrier casting or housing cover.

REMOVAL AND INSTALLATION

REAR AXLE HOUSING

REMOVAL

1.
Raise the vehicle and support it

with safety stands under the rear

frame member.

2.
Drain the lubricant from the

axle.

3.
Make scribe marks on the drive

shaft end yoke and the axle U-joint

flange to insure proper position of the

drive shaft at assembly (Fig. 14). Dis-

connect the drive shaft at the drive

pinion flange.

4.
Disconnect the lower end of the

shock absorbers.

5.
Remove the wheels, brake drums

and both axle shafts as outlined in the

foregoing Section 2.

6. Remove vent hose front vent

tube (Corbin clamp) and remove vent

tube from brake tube junction and

axle housing.

7.
Remove the hydraulic brake T-
fitting from the axle housing. Do not

open the hydraulic brake system lines.

Remove the hydraulic brake line from

its retaining clip on the axle housing.

8. Remove both axle shaft oil seals

with the tools shown in Fig. 8.

9. Remove both brake backing

plates from the axle housing and sus-

pend them above the housing with me-

chanic's wire. The hydraulic brake

SCRIBE MARKS

5/16-24

4 REQ'D.

12-15
LB.
FT.

U-BOLT - 4529 2 REQ'D.

E 1783-A

FIG. 14—Drive Shaft-to-Axle

U-Joint
Connection

El231-A

FIG. 73—Rear Axle Installation—Typical
lines and the parking brake cables are

still attached to the brake carrier

plates.

10.
Support the rear axle housing

on a jack, and then remove the spring

clip nuts. Remove the spring clip

plates (Fig. 13)

11.
Lower the axle housing and re-

move it from under the vehicle.

12.
If the axle housing is being re-

placed, transfer all the differential and

pinion parts to the new housing. See

Section 4, Major Repair Operations.

INSTALLATION

1.
Raise the axle housing into posi-

tion so that the spring clip plates can

be installed. On a Montego or Fair-

lane,
position the spring upper insula-

tors and retainers between the axle

housing and springs and install the

lower insulators. Torque the spring

clip nuts to specification.

2.
Place the brake backing plates in

their normal position on the axle

housing. Use new gaskets on each side

of the brake backing plates.

3.
Install new axle shaft oil seals

with the tool shown in Fig. 8. Soak

the new seals in light weight engine oil

(SAE 10) for 1/2 hour before install-

ing them. Installation without use of

the proper tool will distort the seal

and cause leakage. Coat the outside

edges of the new oil seal with a non-

hardening type of sealer such as Per-

matex No. 2 or its equivalent.

4.
Install the axle shafts, brake

drums and wheels as outlined in Sec-

tion 2.

5.
Attach the hydraulic brake line

T fitting to the axle housing, and se-

cure the hydraulic brake line in its re-

tainer on the axle housing.

6. Install vent tube to brake tubeprocarmanuals.com

04-03-07
Rear Axles — Integral Carrier Type

04-03-07

junction and install vent hose to vent

tube.

7.
Raise the axle housing and con-

nect the shock absorbers.
8. Connect the rear end of the drive

shaft to the axle U-joint flange, align-

ing the scribe marks made on the

drive shaft end yoke and the axle U-
joint flange (Fig. 14).

9. Fill the axle with the proper

grade and amount of lubricant.

10.
Road test the vehicle.

MAJOR REPAIR OPERATIONS

DISASSEMBLY

All service operations on the differ-

ential case assembly and the drive pin-

ion assembly can be performed with

the housing in the vehicle.

REMOVAL OF

DIFFERENTIAL

CASE AND DRIVE PINION

1.
Raise the vehicle and support it

on the underbody, so that the rear

axle drops down as far as the springs

and shock absorbers permit.

2.
Remove the cover from the car-

rier casting rear face, and drain the

lubricant.

3.
Perform the Inspection Before

Disassembly of Carrier in Part 4-1,

Section 3.

4.
Remove both rear wheels.

5.
Remove the brake drums.
6. Working through the hole pro-

vided in the axle shaft flange, remove

the nuts that attach the wheel bearing

retainers to the axle housing.

7.
Pull the axle shafts with the tool

shown in Fig. 2. Care must be exer-

cised to prevent damage to the oil

seals.
Install a nut on one of the brake

backing plate attaching bolts to hold

the plate to the axle housing after the

shaft has been removed. Remove both

seals with the tool shown in Fig. 8.

8. Make scribe marks on the drive

shaft end yoke and the axle U-joint

flange to insure proper position of the

drive shaft at assembly (Fig. 14). Dis-

connect the drive shaft from the axle

U-joint flange. Be careful to avoid

dropping the loose universal joint

bearing cups. Hold the cups on the

spider with tape. Mark the cups so

that they will be in their original posi-

tion in relation to the flange when
they are assembled. Remove the drive

shaft from the transmission extension

housing. Install an oil seal replacer

tool in the transmission extension

housing to prevent transmission leak-

age.
Refer to the transmission group

for the appropriate tool.

9. Remove the differential bearing

adjusting nut locks (Fig. 15).

10.
Mark one differential bearing

cap and the case (Fig. 16) to help po-

sition the parts properly during as-

sembly.

11.
Remove the differential bearing

cap bolts and bearing caps. Hold the

differential case assembly in the hous-

ing after the caps are removed.

12.
Remove the differential case

and bearing cups (Fig. 17).

13.
Hold the drive pinion flange

and remove the pinion nut (Fig. 9).

14.
Remove the pinion flange (Fig.

10).

DIFFERENTIAL PINION GEAR

AND THRUST WASHER

COVER AND GASKET
DIFFERENTIAL SIDE GEAR

AND THRUST WASHER

SHAFT RETAINER DIFFERENTIAL

PINION SHAFT DIFFERENT|AL

DIFFERENTIAL CASE CASE COVER
BEARING ADJUSTING NUT

PINION AND RING GEAR

AXLE SHAFT
BEARING

DRIVE GEAR ATTACHING BOLT

ADJUSTING NUT LOCK

BEARING CAP

PINION LOCATING SHIMS

BEARING AND CUP

WHEEL BEARING RETAINER

GASKET
BEARING AND CUP

SEAL

AXLE SHAFT SEAL

BEARING PRELOAD SPACER/
AXLE HOUSING

FILLER PLUG

'WHEEL BEARING

WHEEL BEARING RETAINER

DEFLECTOR FLANGE

E1908A

FIG. 75—Disassembled Rear Axleprocarmanuals.com