engine FORD MUSTANG 1969 Volume One Chassis

05-02-01
General Clutch Service

05-02-01

PART
5-2
General Clutch Service

COMPONENT INDEX
MODEL APPLICATION

3

a>
1
o>

il

•U
i
!-

II

CLUTCH DISC

Cleaning and Inspection

02-04
02-04
02-04

02-04
02-04
02-04

02-04
02-04
N/A
N/A

N/A

CHECKING FLYWHEEL HOUSING

ALIGNMENT

02-01
02-01
02-01

02-01
02-01
02-01

02-01
02-01
N/A
N/A

N/A

CORRECTING FLYWHEEL HOUSING

ALIGNMENT

02-03
02-03
02-03

02-03

02-03
02-03

02-03

02-03
N/A
N/A

N/A

PILOT BUSHING

Cleaning and Inspection

02-04
02-04
02-04
02-04

02-04
02-04

02-04

02-04
N/A
N/A

N/A

PRESSURE PLATE AND COVER

Cleaning and Inspection

02-04
02-04
02-04
02-04

02-04
02-04

02-04
02-04
N/A

N/A

N/A

RELEASE BEARING

Cleaning and Inspection

02-04
02-04

02-04
02-04
02-04
02-04

02-04
02-04
N/A

N/A

N/A

A page number indicates that the item is for the vehicle listed at the head of the column.

N/A indicates that the item is not applicable to the vehicle listed.

l
FLYWHEEL HOUSING ALIGNMENT

Alignment of the flywheel housing

bore and rear face with the engine

should be checked as a possible cause

of any of the following troubles- ex-

cessive transmission gear wear, ..ans-

mission jumping out of gear, especial-

ly third gear, drive line vibration, ex-

cessive pilot bushing wear, noisy re-

lease bearing, or excessive clutch spin

time.

INSPECTION

1. With the clutch release bearing

removed, install the indicator pilot

tool shown in Fig. 1.

2.
Clean the faces of the flywheel

housing bolt bosses, and remove all

burrs, nicks, and paint from the

mounting face of the housing.

3.
Install the dial indicator on the

pilot and adjust the holder so the but-

ton will contact a circumference just

inside of the transmission mounting

holes.

4.
Push the flywheel forward to re-

move crankshaft end play. Set the dial

indicator face to read zero.

5.
Remove the spark plugs to alle-

viate compression.

6. Pull the engine crankshaft

through one revolution. The crank-

shaft must be held in the forward po-

sition while rotating it.

7. Note the indicator reading and

mark the maximum point of runout

on the face of the housing (Fig. 1).
8. Position the dial indicator to

check bore alignment (Fig. 1). The

bore must be clean and free of burrs,

nicks and paint.

9. Pull the crankshaft through one

revolution. Note the indicator reading

and mark the maximum point of run-

out on the face of the housing as

shown in Fig. 1.

10.
Remove the dial indicator from

the crankshaft and the housing.

11.
Select the Dia-L-lgner pilot

(Fig. 2) which will fit snugly in the

bore of the flywheel housing.

12.
Press the pilot into place on the

locator on the back of the dial.
13.
Position the Dia-L-lgner on the

face of the housing (Fig. 3) with the

pilot in the bore.

14.
Rotate the face runout arrow to

the positive face runout mark on the

housing.

15.
Without moving the face runout

arrow, rotate arrow A until it is at the

negative bore reading.

16.
Slide arrow A to register the

amount of bore runout on the .010-

line of the white scale. Use the

scale No. to coincide with the pilot

being used.

17.
Rotate arrow B until it points

CHECKING
FACE
RUN OUT

CHECKING
BORE
RUN OUT

C
1783-
A

FIG.
1—Flywheel
Housing Alignment Checkprocarmanuals.com

05-02-03
General Clutch Service
05-02-03

in the direction of the face runout

arrow and its center line is parallel to

the center line of the face runout

arrow.

18.
Determine the amount of the

face runout on the B arrow scale.

19.
The value of the circular line

beneath the amount of face runout

will be the desired reading. If the

reading is in excess of 0.014 inch the

housing alignment is unacceptable.

20.
Remove the Dia-L-lgner gauge

from the flywheel housing.

21.
Install the spark plugs and con-

nect the wires.

ENGINE IN VEHICLE

Since any change in face alignment

will change bore alignment, it may be

possible to correct bore alignment by

changing face alignment. Face align-

ment can be changed by shimming be-

tween the flywheel housing and en-

gine.
Fig. 4 shows the type of shim

which can be fabricated.

Not more than 0.010 inch thickness

shims may be used between the fly-

wheel housing and engine. If a 0.010-

inch shim will not bring face and bore

alignment within limits, replace the

flywheel housing.

The shim required is one half the

maximum (—) indicator reading, and

should be located at the point of max-

imum minus (—) indicator reading.

If both the bore and face alignment

are out of limits, shim between the

flywheel housing and engine to bring

face alignment within limits. Check

the bore alignment.

If the bore alignment is out of lim-

its and the face alignment is within

limits,
shim the flywheel housing to

the limit of face misalignment and

check the bore alignment. If it is not

within limits, replace the housing.

ENGINE OUT OF VEHICLE

The same procedure to correct

alignment may be used with the en-

gine out of the vehicle or in the vehi-

cle,
up to the point of replacing the

flywheel housing. If the bore align-

ment cannot be brought within limits

by shimming, follow this procedure:

dure:

1.
Remove the flywheel housing

from the engine and remove the dowel

pins.
Install the flywheel housing and

tighten the attaching bolts.

2.
Install the dial indicator (Fig. 1).

Check the face alignment, and shim as
C2068-A

. 3—Dia-L-lgner Gauge Installed

required to bring face alignment with-

in limits.

3.
Position the indicator to check

the bore alignment. If the bore align-

ment is not within limits, reduce the

tension on the flywheel housing at-

taching bolts so that the housing can

be moved by striking it with a lead

hammer or a block of wood and a

steel hammer.

4.
The lateral alignment should be

brought within limits so that an indi-

cator reading is within limits between

the 9 o'clock and the 3 o'clock posi-

tions on the bore circle. When the lat-

eral alignment is within limits the

housing usually can be moved straight

up or down without disturbing the lat-

eral alignment. When alignment is

within limits, torque the housing bolts

and recheck bore alignment.

5.
If the flywheel housing cannot be

moved enough to bring the alignment

within limits, mark the holes restrict-

ing movement, and then remove the

housing and drill the marked bolt

holes 1/32 inch larger.

6. When the flywheel housing bore

alignment is within limits and the at-

taching bolts are at normal torque,
C 178 4-A

FIG. 4— Fabricated Flywheel

Housing Shim

hand ream the dowel pin holes 1/32

inch larger. Use a straight reamer and

ream from the flywheel housing side.

Oversize dowel pins can be made from

drill rod stock.

7.
Remove the flywheel housing

and then install the oversize dowel

pins in the cylinder block. Complete

the assembly in the usual way.

8. Recheck the flywheel housing

with the Dia-L-lgner gauge to make

sure that the housing is within the spe-

cified limits.procarmanuals.com

05-02-04
General Clutch Service

05-02-04

CLEANING AND INSPECTION

RELEASE BEARING

Wipe all oil and dirt off the release

bearing. The bearing is prelubricated

and should not be cleaned with sol-

vent.

Inspect the bearing retainer for

loose spring clips and rivets.

Inspect the release bearing assembly

for burrs which may cause the assem-

bly to drag on the transmission bear-

ing retainer. Any such burrs should be

cleaned up with fine crocus cloth. If

burrs are found, inspect the transmis-

sion input shaft bearing retainer for

evidence of scoring. Any scoring

should be polished out with crocus

cloth. Coat the bearing retainer with a

thin film of lithium-base grease

(C3VY-19586-A). Prior to release

bearing installation, apply a light film

of lithium base grease (C3VY-

19586-A) on both sides of the release

lever fork where it contacts the release

bearing hub and retaining springs.

Apply a light film of lithium base

grease (C3VY-19586-A) plate to the

release bearing surface that contacts

the pressure plate fingers. Carefully

fill the grease groove inside the bear-

ing hub with lithium base grease (no

polyethylene). Clean all excess grease

from the bore of the bearing hub. Ex-

cess grease will be forced onto the

spline by the transmission input shaft

bearing retainer and will contaminate

the clutch disc. Also, care must be

exercised when applying lubricants to

the release bearing, release bearing

hub and the release lever fork to avoid

excessive grease from contaminating

the clutch disc.

Hold the bearing inner race and ro-

tate the outer race while applying

pressure to it. If the bearing rotation

is rough or noisy, replace the bearing.

Most release bearing failures are

caused by improper clutch pedal ad-

justments. If the clutch linkage does

not have enough free travel, the re-

lease bearing will constantly touch the

release fingers and will spin whenever

the engine is running.

When installing a release bearing on

vehicles equipped with separate hub

and bearing, use the tool shown in

Fig. 5.

Release bearing failure can be

caused by the release lever contact

points being out of plane. Check the

wear on the release bearing assembly

where the release lever contacts it.

If one side of the assembly shows

more wear than the other, the release
lever is bent out of plane, or is not

centering on the bracket on the fly-

wheel housing.

Misalignment between the engine

and transmission can cause release

bearing failure. Other symptoms of

misalignment are transmission jump-

ing out of gear, especially third gear,

drive line vibration; excessive wear in

the pilot bushing, excessive clutch disc

spin time resulting in gear clash, and

excessive transmission gear wear.

PRESSURE PLATE AND COVER

Inspect the surface of the pressure

plate for burn marks, scores, or rid-

ges.
Generally, pressure plate resur-

facing is not recommended. However

minor burn marks, scores, or ridges

may be removed. During the resurfac-

ing process, the flatness of the pres-

sure plate must be maintained. If the

pressure plate is badly heat-checked or

deeply scored, replace the pressure

plate and cover assembly. Clean pres-

sure plate and flywheel surfaces with a

suitable solvent, such as alcohol to be

sure the surfaces are free from any oil

film. Do not use cleaners with petrole-

um base, and do not immerse the

pressure plate in the solvent.

Place the plate on the floor, being

careful not to score or scratch the sur-

face.
Force each individual finger

down, then release quickly. If the fin-

ger does not return quickly, a binding

condition is indicated, and the pres-

sure plate should be replaced.

The pressure plate should be lubri-

cated with a lithium-base grease be-

tween the driving lugs and the edges

of the pressure plate openings, as

shown in Fig. 6. Depress the pressure

plate fingers fully, apply the lubricant,

and then move the fingers up and

down until the lubricant is worked in.

Do not apply excessive lubricant.

CLUTCH DISC

Inspect the clutch disc facings for

oil or grease. Eliminate the source of

any oil or grease before replacing the

disc. An excessive amount of grease in

the pilot bushing or release bearing

hub will find its way to the disc fac-

ings.
Too much lubricant in the trans-

mission or a plugged transmission

vent will force the transmission lubri-

cant out the input shaft and onto the

disc facings. Also, rear main bearing

oil seal leaks or oil leaks from the fly-

wheel mounting bolts can contaminate

the clutch disc.
Inspect the clutch disc for worn or

loose facings. Check the disc for worn

or loose facings. Check the disc for

distortion and for loose rivets at the

hub.
Check for broken springs.

Springs loose enough to rattle will not

cause noise when the car is operating.

Replace the disc assembly if any of

these defects are present. Be especially

careful when installing a new disc to

avoid dropping it or contaminating it

with oil or grease.

PILOT BUSHING

Check the fit of the clutch pilot

bushing in the bore of the crankshaft.

The bushing is pressed into the

crankshaft and should not be loose.

Inspect the inner surface of the bush-

ing for wear or a bell-mouthed condi-

tion. If the bushing is worn or dam-

aged, replace the bushing with a new

service bearing. Refer to the applica-

ble engine for the replacement proce-

dure.

C 1785-A

FIG. 5—Installing Clutch Release

Bearing on Hub

PRESSURE PLATE

AND COVER

DRIVING

LUG
FLYWHEEL

C2048-A

FIG. 6—Pressure Plate Lubrication

Pointsprocarmanuals.com

05-03-02

Clutch
05-03-02

IN-VEHICLE ADJUSTMENTS AND REPAIRS

SPRING-7A600

EQJALIZER ROD-7A516

EQUALIZER BAR-7528

SPRING-7523
FELTWASHER-375475

EQUALIZER
EQUALIZER ROD-7A516

LOCKNUT-34809-S7

RELEASE ROD/

7B543

SNAP RING-7A629

OUTER BRACKET-7507

PIVOT-7A531

RELEASE ROD-7B543

RELEASE ROD-7B543

OUTER EQUALIZER BAR-7528
BUSHING-7526

SPRING-7A632

SNAP RING-7A629

FELT WASHER-375475-S
BUSHING-7543 SPRING-7523

FELT WASHER-358979-S

SPRING-7545

FAIRLANE AND MONTEGO

390 AND 428 ENGINES
FAIRLANE AND MONTEGO

302 AND 351

FIG.
2—Clutch
Pedal and Linkage Adjustment — Fairlane, Montego and Falcon

ASSIST SPRING BRACKET 7535-
ASSIST SPRING 7B572

SPRING

7A632

RELEASE ROD 7B543

390 ENGINE

SAME AS MAIN VIEW

EXCEPT AS SHOWN
351 ENGINE

SAME AS MAIN VIEW

EXCEPT AS SHOWN

C2056-A

FIG.
3—Clutch
Pedal and Linkage Adjustment — Mustang, Cougarprocarmanuals.com

05-03-03
Clutch
05-03-03

CLUTCH PEDAL

ADJUSTMENTS

Adjust
the
clutch pedal free travel

whenever
the
clutch does
not
disen-

gage properly,
or
when
new
clutch

parts
are
installed. Improper adjust-

ment
of the
clutch pedal
is one of the

most frequent causes
of
clutch failure

and
can be a
contributing factor
in

some transmission failures.

FREE TRAVEL

1.
Disconnect
the
clutch return

spring from
the
release lever.

2.
Loosen
the
release lever
rod

locknut
and
adjusting
nut
(Figs.
1, 2

and
3).

3.
Move
the
clutch release lever

rearward until
the
release bearing

lightly contacts
the
clutch pressure

plate release fingers.

4.
Adjust
the rod
length until
the

rod seats
in the
release lever pocket.

5.
Insert
the
specified feeler gauge

between
the
adjusting
nut and the

swivel sleeve. Then tighten
the
adjust-

ing
nut
against
the
gauge finger tight.

6. Tighten
the
locknut against
the

adjusting
nut,
being careful
not to di-

sturb
the
adjustment. Torque
the
lock-

nut
to
specification
and
remove
the

feeler gauge.

7.
Install
the
clutch return spring.

8. Check
the
free travel
at the
pedal

for conformance
to
specification.
Re-
adjust
if
necessary.

9.
As a
final check, measure
the

pedal free travel with
the
transmission

in neutral
and the
engine running
at

about 3000
rpm. If the
pedal free

travel
at
this speed
is not a
minimum

of
1/2
inch, readjust
the
clutch pedal

free travel. Otherwise,
the
release
fin-

gers
may
contact
the
release bearing

continuously, resulting
in
premature

bearing
and
clutch failure. Free travel

must
be
exactly
to
specification.

CLUTCH ASSIST

SPRING REPLACEMENT

(FAIRLANE, FALCON,

MONTEGO)

1.
Remove
the
cotter
pin
from
the

clutch
rod at the
clutch pedal lever
as-

sembly inside
the
passenger compart-

ment.

2.
Grasp
the
clutch pedal lever

firmly
to
prevent slipping
and
remove

the clutch
rod
from
the
lever. Allow

the clutch pedal lever
to
rest
on the

floor panel.

3.
Remove
the
forward bolt secur-

ing
the
assist spring bracket
to the

brake pedal bracket
and
loosen
the

rear bolt
two or
three turns.
Do not

remove
the
rear bolt.

4.
Grasp
the
assist spring bracket

with pliers
and
rotate upward until
the

spring
can be
separated from
the

bracket.

BRAKE PEDAL

BRACKET

CLUTCH ASSIST SPRING

BRACKET
-
7535

CLUTCH PEDAL

7519
5.
Position
the
assist spring
in the

clutch pedal spring bracket
and the

assist spring bracket. Rotate
the

spring bracket downward until
the

forward bolt holes
in the
assist spring

bracket line
up
with
the
holes
in the

brake pedal bracket
(Fig. 4).

6. Install
the
forward bolt retaining

the assist spring bracket
to the
brake

pedal bracket
and
torque
the
forward

and rear bolts
to
specification.

7.
Install
the
clutch
rod to the

clutch pedal lever
and
insert
the
cotter

pin.

CLUTCH PEDAL, PEDAL

ASSIST SPRING AND/OR

BUSHING REMOVAL

AND INSTALLATION

FORD, MERCURY,

METEOR

1.
Remove
the pin
that secures
the

clutch pedal-to-equalizer
rod to the

clutch pedal.

2.
Grasp
the
clutch pecal lever

firmly
to
prevent slipping
and
remove

the clutch
rod
from
the
lever. Allow

the clutch pedal lever
to
rest
on the

floor.

3.
Loosen
the
lower bolt securing

the assist spring bracket
to the
pedal

support bracket
two or
three turns.

Then, remove
the
upper bolt from
the

bracket.
Do not
remove
the
lower

bolt.

4.
Grasp
the
assist spring bracket

with pliers
and
rotate
it
counterclock-

wise until
the
spring
is
free
(Fig 5).

5.
Remove
the
retaining ring from

the
end of the
clutch pedal shaft. Then

remove
the
shaft, bushings
and
clutch

pedal from
the
support.

6. Remove
the
bushings from
the

pedal shaft
and
pedal support
and

transfer
the
rubber pedal
pad.

7.
After lubricating
the
pedal shaft

ASSIST SPRING

LOWER BOLT

ASSIST SPRING BRACKET-

UPPER
BOL"

C 1769-B

FIG. 4—Clutch Pedal Assembly
—
Fairlane, Montego, Falcon
C2058-A

;. 5—Removing Clutch Assist

Spring
—
Ford,
Mercury and Meteorprocarmanuals.com

05-03-04
Clutch

05-03-04

bushings, position the clutch pedal and

bushings in the pedal support.

8. Install the retaining ring on the

clutch pedal shaft.

9. Position the assist spring in the

pedal support bracket and the assist

spring bracket. Rotate the assist

spring bracket clockwise until the

upper bolt holes line up and install the

bolt. Torque both the upper and lower

bolts to specification.

10.
Check the clutch pedal free

travel and adjust as required.

MUSTANG, COUGAR

1.
Disconnect the battery ground

cable.

2.
Remove the steering column.

Refer to Group 3 of this manual for

the procedure.

3.
Remove the two capscrews re-

taining the master cylinder or booster

to the dash panel. Then remove the

two capscrews retaining the pedal sup-

port bracket to the dash panel.

4.
Working inside the vehicle, dis-

connect the clutch pedal-to-equalizer

rod at the clutch pedal by removing

the retainer and bushing.

5.
Secure the clutch pedal against

the bumper stop with a small C-clamp

as shown in Fig. 6.

6. Disconnect the stop light switch

wires at the connector.

7.
Remove the switch retainer and

slide the stop light switch off the

brake pedal pin just far enough for

the switch outer hole to clear the pin.

Then lower the switch away from the

pin.
Remove the master cylinder push

CLUTCH PEDAL ASSIST SPRING
rod, bushing and nylon washer from

the brake pedal pin.

8. Remove the screw retaining the

pedal support bracket to the top inner

cowl bracket (Fig. 6).

9. Remove the two sheet metal

screws retaining the pedal support

bracket to the dash panel.

10.
Remove the two screws retain-

ing the pedal support bracket to the

upper cowl brace and lower the pedal

support bracket away from the steer-

ing column studs.

11.
Remove the pedal support

bracket assembly from the vehicle.

12.
Mount the bracket in a vise.

13.
Remove the small C-clamp se-

curing the clutch pedal to the bumper.

Slowly pivot the pedal away from the

bumper until the assist spring can be

lifted from its seat.

14.
Remove the retainer clip from

the clutch and brake pedal shaft.

Then, remove the clutch pedal and

shaft assembly, brake pedal assembly,

and bushings from the pedal support

bracket.

15.
Apply a coating of SAE 10 en-

gine oil to the bushings and locate all

bushings in their proper places on the

brake and clutch pedal assemblies.

16.
Position the brake pedal to the

pedal support bracket. Install the

clutch and brake pedal shaft through

the pedal support and brake pedal as-

sembly. Install the retainer.

17.
Install the clutch pedal assist

spring and pivot the pedal against its

bumper stop. Secure the pedal against

the bumper with a small C-clamp as

TOP INNER COWL-TO-BRACKET

RETAINING SCREW

C2057-A

FIG.
6—Clutch
Pedal —Mustang and Couga?
shown in Fig. 6.

18.
Position the pedal support

bracket assembly to the dash panel

and to the steering column retainer

studs.

19.
Align the pedal support bracket

holes with the holes in the dash panel

and install the two sheet metal screws.

20.
Install the two capscrews at-

taching the pedal support bracket to

the upper cowl bracket.

21.
Install the screw attaching the

support bracket to the top inner cowl

bracket (Fig. 6).

22.
Install the inner nylon washer,

bushing master cylinder push rod on

the brake pedal pin. Position the stop

light switch so that it straddles the

push rod with the switch slot on the

pedal pin and the switch outer hole

just clearing the pin. Slide the switch

completely onto the pin, and install

the outer nylon washer. Secure with

the self-locking pin.

23.
Connect the stop light switch

wires to the connector and install the

wires to the retaining clip.

24.
Connect the clutch pedal-

to-equalizer rod to the clutch pedal

assembly with the bushing and retain-

er and remove the C-clamp from the

bracket.

25.
Working from the engine side

of the dash panel, install the two cap-

screws attaching the pedal support

bracket to the dash panel. Then install

the two screws attaching the master

cylinder to the dash panel.

26.
Install the steering column.

Refer to Group 3 of this manual for

the procedure.

27.
Adjust the clutch pedal free

travel.

28.
Check the brake pedal free

height and travel measurements

(Group 2).

29.
Connect the battery ground

cable.

CLUTCH PEDAL AND/OR

BUSHING REMOVAL

AND INSTALLATION

MOM EGO, FALCON

FAIRLANF

1.
Remove the retaining clip (Fig.

2) that secures the equalizer rod to the

clutch pedal. Disconnect the rod from

the pedal.

2.
Remove the lower bolt retaining

the assist spring bracket to the pedal

support. Then, loosen the upper

bracket retaining bolt (approximately

4 turns) and disconnect the spring

from the clutch pedal and bracket.

3.
Disconnect the brake pedal push

rod from the brake pedal.procarmanuals.com

05-03-06
Clutch

05-03-06

8. Remove the starter cable then

remove the starter motor from the fly-

wheel housing.

9. Remove the bolts that secure the

engine rear plate to the front lower

part of the flywheel housing.

10.
Remove the flywheel housing

lower cover (390 CID housing only).

11.
Remove the bolts that attach

the housing to the cylinder block.

12.
Move the housing back just far

enough to clear the pressure plate,

then move it to the right to free the

pivot from the clutch equalizer bar. Be

careful not to disturb the linkage and

assist spring.

13.
Loosen the six pressure plate

cover attaching bolts evenly to release

the spring tension. If the same pres-

sure plate and cover is to be installed

after the clutch is overhauled, mark

the cover and flywheel so that the

pressure plate can be installed in the

same position.

14.
Remove the pressure plate and

the clutch disc from the flywheel.

CLUTCH INSTALLATION

1.
Install the clutch release lever if

it was removed.

2.
Place the clutch disc, and pres-

sure plate assembly in position on the

flywheel. Start the cover attaching

bolts to hold the pieces in place, but

do not tighten them. Avoid touching

the clutch disc facing, dropping the

parts or contaminating them with oil

or grease as clutch chatter may result.

3.
Align the clutch disc with the

tool shown in Fig. 7, and alternately

tighten the bolts a few turns at a time

until they are all tight. Then torque

the six pressure plate cover attaching

bolts to specification before removing

the tool.
4.
Apply a light film of grease

(C3VY-19586-A) to the outside diam-

eter of the transmission front bearing

retainer. Apply a light film of grease

(C3VY-19586-A) to both sides of the

release lever fork where it contacts the

release bearing bore spring clips.

Apply a light film of grease to the re-

lease bearing surface that contacts the

pressure plate release fingers. Fill the

grease groove of the release bearing

hub with lithium base grease (C3VY-

19586-A). Clean all excess grease

from inside the bore of bearing hub.

Excess grease will be forced onto the

spline by the transmission input shaft

bearing retainer and will contaminate

the clutch disc. Also, place the release

bearing and hub on the release lever.

5.
Make certain that the flywheel

housing and the cylinder block mount-

ing surfaces are clean. Position the

felt washer on the pivot in the fly-

wheel housing. Slip the pivot into the

clutch equalizer shaft being careful

not to disturb the linkage and at the

same time position the housing on the

dowels in the cylinder block. Install

and torque the attaching bolts to spec-

ification.

6. Install the starting motor and

connect the cable.

7.
The mounting surfaces of the

transmission and the flywheel housing

must be free of dirt, paint, and burrs.

Install two guide pins in the flywheel

housing lower mounting bolt holes.

Move the transmission forward on the

guide pins until it is tightly positioned

against the flywheel housing.

8. Install the two upper mounting

bolts.
Then, remove the guide pins

and install the two lower mounting

bolts.
Torque all the bolts to specifica-

tion.

9. Raise the rear of the engine and
install the crossmember. Install and

torque the crossmember attaching

bolts to specifications, then lower the

engine.

10.
Install the extension housing-

to-engine rear support attaching bolts.

Torque the bolts to specification.

11.
Remove the transmission jack

and connect the parking brake cable.

12.
If the vehicle is equipped with a

four-speed transmission, connect the

gear shift linkage control bracket to

the extension housing.

13.
Connect the gear shift rods to

the transmission. Adjust the shift link-

age as required.

14.
Connect the release lever retain-

ing spring. Install the flywheel housing

cover (390 CID housing only).

15.
Remove the tool from the

transmission output shaft and install

the drive shaft.

16.
Check the clutch pedal free

travel.

CLUTCH ARBOR CLUTCH DISC

PRESSURE PLATE

C 1788-A

FIG. 7—Installing Clutch Disc —

Typicalprocarmanuals.com

05-04-01
Specifications

05-04-01

PART
5-4
Specifications

CLUTCH IDENTIFICATION

Car Line

Ford

Meteor

Ford

Ford

Meteor

Ford

Meteor

Mercury

Ford

Falcon

Fairlane

Falcon

Montego

Fairlane

Montego

Falcon

Mustang

Mustang

Cougar

Fairlane

Montego

Fairlane

Montego

Mustang

Cougar

Fairlane

Montego

Mustang

Cougar

Fairlane

Montego

Mustang

Cougar
Engine

240-IV

240-IV

302-2V

390-2V,

4V

429-4V

170-1V

200-IV

250-1V

302-2V

200-IV

250-1V

302-2V

390-2V,

4V

390-4V GT

351-2V,

4V

428-4V
Transmission

3-Speed

3-Speed

Heavy Duty

3-Speed

3-Speed

4-Speed

4-Speed

3-Speed

3-Speed

3-Speed

4-Speed

3-Speed

3-Speed

4-Speed

3-Speed

4-Speed

3-Speed

4-Speed

3-Speed

4-Speed

4-Speed
Pressure Plate

Diameter

(Inches)

9.5

11

10

11

11.5

9

9

10

9

10

11

11.5

11

11.5
No.
of

Springs

6

9

9

9

12

6

6

9

6

9

9

12

9

12
Color Identification

(Paint Daub)

Pressure Plate-No Color

Cover—Green

Springs—Aluminum

Pressure Plate-White

Cover-Pink and Blue

Springs
8-Green

Pressure Plate-Green

Cover-White

Springs-White
on
Bronze

Pressure Plate—Orange

Cover-Black

Springs-Aluminum

Pressure Plate-Yellow

Cover-Black

Springs-Green

Pressure Plate-Orange

Cover—Purple

Springs-Aluminum Stripe

Pressure Plate-Orange

Cover-Purple

Springs-Aluminum Stripe

Pressure Plate—Green

Cover-White

Springs-Bronze

Pressure Plate—Orange

Cover—Purple

Springs—Aluminum Stripe

Pressure Plate-Blue

Cover—Purple

Springs—Bronze

Pressure Plate-Green

Cover-Purple

Springs-Purple

Pressure Plate-Green

Cover-Purple

Springs-Purple

Pressure Plate-Blue

Cover-Yellow

Springs-Silver

Pressure Plate-Yellow

Cover-Black

Springs—Green
Disc

Diameter

(Inches)

9.5

11

10

11

11.5

9

9

10

9

10

11

11.5

11

11.5
No.
of

Springs

6

8

12

12

10

6

6

12

6

6

8

8

8

10
Color Identification

(Paint Daub)

Clutch-Yellow

Springs—2 Purple (Small)

4 Aluminum (Large)

Clutch-No Color

Springs—4 Aluminum

4 Pink

Clutch-Blue

Springs-6 Orange (Small)

6 Pink (Large)

Clutch-Pink

Springs-6 Green (Small)

6 Orange (Large)

Clutch-Gray

Springs—5
Red
Stripe (Small)

5
No
Color (Large)

Clutch-Pink

Springs—Blue

Clutch-Pink

Springs-Blue

Clutch-Blue

Springs-6 Pink

6 Orange

Clutch-Blue

Springs—Blue

Clutch-Green

Springs-Orange

Clutch-Pink
and
Orange

Springs—Aluminum

Clutch-Pink and Orange

Springs—Aluminum

Clutch—Pink and Orange

Springs—Aluminum

Clutch-Gray

Springs-Red Stripe

CLUTCH-DRIVELINE ADJUSTMENTS (INCHES)

Release Lever
Rod
Adjusting
Nut to
Swivel Sleeve

Ford,
Mercury Meteor
0.194

Fairlane, Montego, Falcon, Mustang, Cougar
ex.
with

390,
428
engine
0.136

390,
428
Engines
0.178
*

Clutch Pedal Free Travel (Engine Running)
7/8"-l
1/8"

Clutch Housing Alignment
If
Dia-L-lgner reading
0.014

is greater than that indicated,
the
clutch

housing alignment
is
unacceptable.

Maximum Shim to Correct Alignment
0.010procarmanuals.com

06-02-01
Ford Design Three Speed Transmission

06-02-01

PART 6-2 Ford Design Three Speed
Transmission

Trans-

mission

Model

RAN-AL

RAN-AM

RAN-AN

RAN-AZ

RAT-AJ

RAT-AM

RAT-A2

RAT-B2

RAT-C2

RAT-N2

RAT-SI

RAT-T

RAT-U1
Engine

Model

200-IV, 250-IV

200-IV, 250-IV

170-1V

240-IV

351-2V-4V

351-2V-4V

390-2V-4V

390-4V-GT

390-4V-GT

390-4V

302-2V

302-2V-4V

302-2V
Shift

Lever

Location

Column

Floor

Column

Column

Column

Floor

Column

Floor

Column

Floor

Column

Column

Floor
MODEL APPLICATION
All
Models
Ford

X

X

X
Mercury
X

X
Meteor
X
Cougar
X

X
Fairiane
X

X

X

X

X
Falcon
X

X

X
Montego
X

X

X

X

X
Mustang
X

X

X
Lincoln-
Continental
Thunderbird
Continental-
Mark
III

COMPONENT INDEX

COUNTERSHAFT GEAR BEARINGS

Removal and Installation

DESCRIPTION

GEAR SHIFT CONTROL ASSEMBLY—

Floor Mounted

Removal and Installation

GEAR SHIFT LEVERS AND SEALS

Removal and Installation

GEAR SHIFT LINKAGE ADJUSTMENT

Column Mounted

Floor Mounted

INPUT SHAFT BEARING

Removal and Installation

SYNCHRONIZERS

Disassembly and Assembly

TRANSMISSION (Complete)

Cleaning and Inspection See Part 06-01

Disassembly and Overhaul

Removal and Installation

AH
Models
02-07

02-02

02-07

02-06

02-02

02-03

02-06

02-06

02-04

02-03
procarmanuals.com

06-02-02
Ford Design Three Speed Transmission

06-02-02

DESCRIPTION

DESCRIPTION

The RAN and RAT Model three-

speed transmission (Fig. 1) are used

on models having 170, 200, 240, 250,

302,
351 and 390 C.I.D. engines. The

specifications of this section, Part 6-4,

lists the transmission model numbers

and vehicles in which they are used.

A transmission service identification
tag is located on the right side of the

case at the front (Fig. 2). The first

line on the tag will show the transmis-

sion model and service identification

code when required. The second line

will show the transmission serial num-

ber. Additionally, a driveline compo-

nent identification tag is attached to

the upper right side of the transmis-

sion case.
This transmission is of the fully

synchronized type, with all gears ex-

cept the reverse gear and sleeve being

in constant mesh. All forward-speed

changes are accomplished with syn-

chronizer sleeves.

The forward-speed gears are

helical-cut and are in constant mesh.

Gears used in the reverse gear train

are spur-cut and are not synchronized.

C2O87-A

FIG.
1—Three-Speed
Transmission—Typical
TRANS.
MODEL

SERIAL
NO.

C 2089-A

FIG.
2—Transmission
Identification

Tag

IN-VEHICLE ADJUSTMENTS
AND
REPAIRS

GEAR SHIFT LINKAGE

ADJUSTMENT—COLUMN

MOUNTED

1. Place the gear shift lever in the

neutral position.

2.
Loosen the two gear shift rod

adjustment nuts.

3.
Check shift levers on transmis-

sion to be in neutral position.

4.
Insert a 3/16-inch diameter

alignment tool through the first and

reverse gear shift lever, the second and

third gear shift lever and both holes

in the lower casting (Fig. 3). An align-

ment tool can be made from 3/16

inch drill rod bent to an L shape.

The extensions should be 1 inch and 2

inches from the elbow. The short end

of the tool should be inserted into the

alignment holes.

5.
Tighten the two gear shift rod

adjustment nuts.

6. Remove the alignment tool from

the levers.

7.
Start the engine and shift the se-

lector lever to each position to make

sure it operates freely.
FIG.
3—Gearshift
Linkage Adjustment—Typicalprocarmanuals.com