battery replacement FORD MUSTANG 1969 Volume One Chassis

03-05-02
Steering Columns
And
Linkage

03-05-02

which also will shear away during
im-

pact.

TILT STEERING COLUMNS

The steering column
is of the col-

lapsible type
to
lessen
the
possibility

of injury
to the
driver
of the
vehicle

should
he
become involved
in an
acci-

dent.
The
lower
end of the
steering

column tube
at the
bellows area will

collapse approximately
six
inches

upon
a
hard impact.

The shift tube
and the
steering shaft

are provided with plastic dowels
and

will shear
and
allow them
to
collapse

in proportion
to the
outer tube upon

impact.

Once
the
steering column
has
been

collapsed,
a
complete
new
column
must
be
installed.

The tilt column features nine driv-

ing positions (four
up and
four down

from
a
center position).
The
.column

also features
a
turn signal switch with

a lane-changer position turn indicating

position
and
emergency warning flash-

er control.

TILT-AWAY STEERING COLUMNS

The tilt-away steering column
fea-

tures nine driving positions (four
up

and four down from
a
center position)

and
a
tilt-away position that
is
auto-

matically accomplished
on
Mustang

and Cougar models when
the
ignition

key
is
turned
to the
OFF
position
and

the left door
is
opened.
On
Thunder-

bird models,
the
tilt-away occurs when
the shift lever
is
placed
in
PARK
and

the driverns door
is
opened.

The steering column
is of the col-

lapsible type
to
lessen
the
possibility

of injury
to the
driver
of the
vehicle

should
he
become involved
in an
acci-

dent.
The
lower
end of the
steering

column tube
at the
bellows area will

collapse approximately
six
inches

upon
a
hard impact.

The shift tube
and the
steering shaft

are provided with plastic dowels
and

will shear
and
allow them
to
collapse

in proportion
to the
outer tube upon

impact.

Once
the
steering column
has
been

collapsed,
a
complete
new
column

must
be
installed along with mounting

brackets which will also shear away

during impact.

IN-VEHICLE ADJUSTMENTS
AND
REPAIRS

STEERING WHEEL SPOKE

POSITION ADJUSTMENT

When
the
steering gear
is on the

high point,
the
front wheels should
be

in
the
straight-ahead position
and the

steering wheel spokes should
be in

their normal position with
the
Pitman

arm pointing directly forward.
If the

spokes
are not in
their normal posi-

tion, they
can be
adjusted without
dis-

turbing
the
toe-in adjustment (Part

3-1).

STEERING WHEEL

REPLACEMENT

1.
Disconnect
the
negative cable

from
the
battery.

2.
Working from
the
underside
of

the steering wheel spoke, remove
the

crash
pad
attaching screws. Lift
the

crash
pad
from
the
wheel.
(On
Conti-

nental Mark
III
models,
pry out the

crash
pad
insert
and
remove
the two

screws that secure
the
crash
pad. Re-

move
the
crash
pad. On
models

equipped with steering wheel mounted

speed controls, refer
to
Group
16 for

removal instructions). Remove
the

horn ring
(if so
equipped)
by
turning

it counterclockwise.

3.
Remove
the
steering wheel
nut,

and then remove
the
steering wheel

with tool T67L-3600-A
(Fig. 1). Do

not
use a
knock-off type steering

wheel puller
or
strike
the end of the

steering shaft with
a
hammer. Striking

the puller
or
shaft will damage
the

bearing
or the
collapsible column.

4.
Transfer
all
serviceable parts
to

the
new
steering wheel.

5.
Position
the
steering wheel
on

the shaft
so
that
the
alignment mark
on
the hub of the
wheel
is
adjacent
to

the
one on the
shaft. Install
a new

locknut
and
torque
it to
specifications.

6. Install
the
horn ring
(if so

equipped)
and
crash
pad.

STEERING COLUMN UPPER

BEARING REPLACEMENT

STATIONARY COLUMNS

Removal

1. Disconnect
the
horn wire
and the

turn indicator wires
at the
connector.

2.
Working from
the
underside
of

the steering wheel spoke, remove
the

two crash
pad
attaching screws. Lift

the crash
pad
from
the
wheel.
(On

Continental Mark
III
models,
pry out

the crash
pad
insert
and
remove
the

two screws that secure
the
crash
pad.

Remove
the
crash
pad. On
models

equipped with steering wheel mounted

speed controls, refer
to
Group
16 for

7oo/-T67L-3600-A
removal instructions). Remove
the

horn ring
(if so
equipped)
by
turning

it counterclockwise.

3.
Remove
the
steering wheel
at-

taching
nut.
Remove
the
steering

wheel using tool T67L-3600-A
(Fig.

1).
Do not use a
knock-off type steer-

ing wheel puller
or
strike
the end of

the steering shaft with
a
hammer.

Striking
the
puller
or
shaft will
dam-

age
the
bearing
or the
collapsible
col-

umn.

4.
Remove
the
turn indicator lever.

5.
Remove
the
turn signal switch

attaching screws. Lift
the
switch over

the
end of the
steering shaft
and
place

it
to one
side.

6. Remove
the
snap ring from
the

top
of the
steering shaft.

7.
Loosen
the two
flange-to-steering

column tube attaching bolts
to
disen-

gage them from
the
tube.

8. Raise
the
flange upward while

BEARING
AND

INSULATOR

Spacer

G 1502 -B

FIG.
1—Removing
Steering Wheel
G 1497-A

FIG. 2—Installing Upper Bearingprocarmanuals.com

03-05-14
Steering Columns And Linkage

03-05-14

8. Connect the turn signal and

emergency flasher switch wires at the

multiple connectors. Connect the wires

to the neutral start switch. Adjust-

ments for the neutral start switch are

detailed in Group 7 of this manual.

9. Connect the tilt-column control

cable to the release cable retainer and

vacuum motor (if so equipped). To re-

move cable slack, loosen the bracket

attaching screw and pull it slightly

toward the column, then tighten the

screw. If difficulty in adjusting this

control is experienced, the retainer

slot may be filed to gain additional

travel.

10.
Install the instrument panel

steering column plate and cover and

the instrument panel lower outer fin-

ish panel.

11.
Connect the negative cable to

the battery.

12.
Start the engine and check the

operation of the steering column and

switches.

LINCOLN CONTINENTAL

Removal

1.
Disconnect the battery.

2.
Disconnect the rod from the
lever at the lower end of the selector

tube.

Loosen the clamp bolt that locks

the flexible coupling to the steering

shaft.

3.
Working from the underside of

the steering wheel spoke, remove the

two screws that secure the crash pad.

Remove the pad. Do not use a ham-

mer or knock-off type wheel puller.

Striking the puller or shaft may cause

damage to the bearings and/or col-

lapsible column. Remove the steering

wheel as shown in Fig. 15.

4.
Remove the instrument panel

steering column finish plate.

5.
Remove the four screws that at-

tach the lower retainer to the dash

panel.

6. Disconnect the turn signal switch

and emergency flasher wires at the

connectors. Disconnect the wires from

the neutral start switch.

7.
While supporting the steering

column, remove the bolts that attach

the lower clamp to the upper bracket

(Fig. 15). Lift the column from the ve-

hicle.

Installation

1.
Position the column in the vehi-
cle,
making sure that the steering

shaft engages the flex coupling.

2.
Install the column retainer-

to-dash panel attaching screws, but do

not tighten them.

3.
Install the lower clamp and the

attaching nuts. Tighten the nuts fing-

ertight.

4.
Move the lower flange as re-

quired to center the steering shaft in

the tube. Aligning procedures are de-

tailed in Part 3-1. Tighten the lower

flange attaching nuts when the shaft is

centered.

5.
Connect the shift rod to the shift

lever at the lower end of the column.

6. Install and tighten the flex cou-

pling attaching bolt.

7.
Tighten the instrument panel-

to-clamp attaching nuts.

8. Connect the turn signal and

emergency flasher switch wirss at the

multiple connectors. Connect the wires

to the neutral start switch. Adjust-

ments for the neutral start switch are

detailed in Group 7 of this manual.

9. Install the instrument panel

steering column finish plate.

10.
Install the steering wheel and

crash pad.

MAJOR REPAIR OPERATIONS

STEERING COLUMN

SHIFT TUBE REPLACEMENT

STATIONARY COLUMN

WITH STANDARD

TRANSMISSION

Removal

1.
Working from the underside of

the steering wheel spoke, remove the

two screws that secure the crash pad.

Remove the pad. (On Continental

Mark III models, pry out the crash

pad insert and remove the two screws

that secure the crash pad. Remove the

crash pad. On models equipped with

steering wheel mounted speed con-

trols,
refer to Group 16 for removal

instructions).

2.
Remove the steering wheel from

the steering shaft with tool T67L-

3600-A (Fig. 1). Then, remove the

tool from the steering wheel. Do not

use a knock-off type steering Wheel

puller or strike the end of the steering

shaft with a hammer. Striking the

puller or shaft will damage the bear-
ing or the collapsible column.

3.
Remove the steering column

from the vehicle.

4.
Remove the selector lever from

the hub (Fig. 16).

5.
Remove the bearing upper snap

ring. It may be necessary to pull the

turn signal switch out to remove the

snap ring.

6. Remove the screws that attach

the shift tube bearing, shift arms, and

shift tube to the lower end of the

steering column.

7.
Slip the shift tube and steering

shaft from the lower end of the steer-

ing column tube. The upper bearing

has a slight press fit on the steering

shaft.

8. Remove the C-washer from the

upper end of the steering shaft, and

pull the shift tube from the steering

shaft.

9. Remove the shift tube bearing

from the lower end of the tube

Installation

1.
Position the shift tube bearing
(Fig. 16) on the tube and insert the

steering shaft in the shift tube.

2.
Install the C-washer on the

upper end of the steering shaft.

3.
Insert the shift tube and steering

shaft into the steerint column tube

and install the three attaching screws

at the lower end of the steering col-

umn tube.

4.
Position the bearing and insula-

tor on the shaft if it was disturbed

during removal. Work it down onto

the shaft as far as possible, then place

a piece of 3/4 ID x 2 1/8 inch pipe

over the end of shaft and install the

steering wheel attaching nut (Fig. 2).

5.
Tighten the nut until the bearing

is seated in the flange, then remove

the nut and pipe from the shaft.

6. Position the turn signal switch

on the flange and install the three at-

taching screws. Install the upper snap

ring.

7.
Install the selector lever and the

turn signal lever in the column.

8. Adjust and install the neutral

start switch as detailed in Group 7.

9. Install the steering column in the

vehicle.procarmanuals.com