boot FORD MUSTANG 1969 Volume One Chassis

02-02-03
Brake System

02-02-03

DESCRIPTION

Disc brakes are available as option-

al equipment for the front wheels on

Ford, Mercury, Meteor, Fairlane,

Montego, Falcon, Mustang and Cou-

gar models and are standard on Thun-

derbird, Continental Mark III, and

Lincoln Continental models. The

dual-master cylinder equipped hydrau-

lic brake system employs single an-

chor, internal expanding and
self-

adjusting drum brake assemblies on

the rear wheels of vehicles with disc

brakes, and on the front and rear

wheels of all others.

A vacuum booster is used with the

power disc brake system.

DUAL MASTER CYLINDER

BRAKE SYSTEM

The dual-master cylinder brake sys-

tem has been incorporated in all mod-

els to provide increased safety. The

system consists of a dual-master cylin-

der (Fig. 1), pressure differential valve

assembly and a switch (Fig. 2). The

switch on the differential valve acti-

vates a dual-brake warning light, lo-

cated on the instrument panel.
DISC BRAKE

The disc brake consists of a venti-

lated rotor and caliper assembly. The

caliper used on all models except Lin-

coln Continental is a single piston

floating caliper (Fig. 3). The caliper

used on Lincoln Continental models is

a four piston fixed caliper (Fig. 4).

A proportioning valve in the rear

hydraulic circuit provides balanced

braking action between front and rear

brakes.

On all models except Lincoln a

pressure impulse valve located at the

primary inlet of the pressure differen-

tial valve prevents brake fluid surge

back to the master cylinder reservoir.

On Lincoln Continental models a

metering valve, in the hydraulic line

between the differential valve and the

front wheel disc brakes, prevents the

front brakes from applying until ap-

proximately 125 psi is obtained in the

system (Fig. 21). This delaying action

is required to prevent the front brakes

from performing all the braking ac-

tion on low speed stops and thereby

increasing the rate of lining wear.
FLOATING CALIPER—

ALL MODELS EXCEPT

LINCOLN CONTINENTAL

The caliper asseml.y is made up of

a floating caliper housing assembly

and an anchor plate. The anchor plate

is bolted to .the wheel spindle arm by

two bolts. The floating caliper is at-

tached to the anchor plate by steel

stabilizers on Ford, Mercury, Meteor,

Thunderbird and Continental Mark

III models and by one stabilizer on

Fairlane, Montego, Falcon, Mustang

and Cougar models. The floating cali-

per slides on two locating pins which

also attach to the stabilizers. The

floating caliper contains the single cyl-

inder and piston assembly. The cylin-

der bore contains a piston with a

molded rubber dust boot to seal the

cylinder bore from contamination

(Fig. 5). A square section rubber pis-

ton seal is positioned in a groove in

the cylinder bore and is used to pro-

vide sealing between the cylinder and

piston (Fig. 7).

The outer brake shoe and lining as-

sembly is longer than the inner assem-

bly, and the shoe and lining

DISC BRAKES

RETURN SPRING

(SECONDARY)

RETAINER

PRIMARY SYSTEM BRAKE

FLUID RESERVOIR

BOOT

PUSH ROD

TUBE SEAT |

(SECONDARY)

BRAKE OUTLET

PORT
RESIDUAL \ ^

CHECK \

VALVE \

SECONDARY PISTON

ASSEMBLY
(PRIMARY)

BRAKE OUTLET

PORT
PRIMARY PISTON

ASSEMBLY
H 1545-A

FIG.
I
—
Dual
Master Cylinder—Typicalprocarmanuals.com

BRAKE WARNING LAMP SWITCH

PISTON
BRAKE WARNING LAMP SWITCH

BRAKE WARNING LAMP SWITCH

PLUNGER IN THE ON POSITION

CONNECTOR
BRAKE WARNING LAMP SWITCH

PLUNGER IN OFF POSITION

VALVE PISTON HAS MOVED

TO LOW PRESSURE AREA.

WARNING LAMP SWITCH

PLUNGER IS DEPRESSED,

LIGHTING THE BRAKE

WARNING LAMP

LOW PRESSURE SIDE
U
VALVE PISTON IS

CENTRALIZED. PRIMARY

AND SECONDARY SYSTEM

PRESSURES ARE EQUALIZED

BRAKE WARNING LAMP

SWITCH PLUNGER IN

OFF POSITION
HIGH PRESSURE SIDE

DRUM BRAKES
TJ
CONNEiCTOR

BRAKE FLUID

BRAKE WARNING LAMP I

SWITCH PLUNGER IN

ON POSITION

REAR BRAKE INLET

CONNECTOR

FRONT BRAKE

INLET

FRONT BRAKE

OUTLET
VALVE PISTON IS CENTRALIZED.

PRIMARY AND SECONDARY SYSTEM

PRESSURES ARE EQUALIZED
OUTLET TO

PROPORTIONING VALVE

DISC BRAKES
\
REAR BRAKE

PROPORTIONING

VALVE IS BYPASSED

VALVE PISTON HAS MOVED TO LOW

PRESSURE AREA. WARNING LAMP SWITCH PLUNGER IS

DEPRESSED, LIGHTING THE BRAKE WARNING LAMP H1634-A

FIG. 2—Pressure Differential Valve and Brake Warning Light Switch

CALIPER ASSEMBLY

BLEEDER

SCREW
EXTERNAL

TRANSFERTU3E

H1567-B
HUB

AND

ROTOR

ASSEMBLY

H 1647-A

FIG. 3—Disc Brake Assembly-

Floating Caliper—All Models

Except Lincoln Continental
FIG. 4—Disc Brake Assembly—

Fixed Caliper—Lincoln

Continental
blies are not interchangable (Fig. 23).

The outboard shoe and lining is fixed

to the floating caliper and is retained

by two pins and spring clips. The shoe

and lining assembly consists of fric-

tion material bonded to a metal plate

called the shoe. It is replaced as a

unit.

FIXED CALIPER

LINCOLN CONTINENTAL

The caliper assembly is bolted di-

rectly to the wheel spindle arm by two

bolts.
The caliper assembly consists of

two caliper housings bolted together

with each half containing two cylinder

bores of 1.938 inch diameter. Each

cylinder bore contains a piston with

an attached molded rubber dust boot

to seal the cylinder bore from contam-

ination (Fig. 6). Square-section rubberprocarmanuals.com

02-02-05
Brake System

02-02-05

piston seals are positioned in grooves

in the cylinder bores and are used to

provide hydraulic sealing between the

cylinders and pistons (Fig. 7).

The cylinders are connected hydrau-

lically by means of internal passages

in the caliper housings and an external

transfer tube between the two halves

of the caliper assembly. One bleeder

screw and fluid inlet fitting is provided

on each caliper assembly.

The shoe and lining assemblies are

located in between parallel machined

abutments within the caliper, and are

supported radially by tabs on the

o'uter ends of the shoe assemblies (Fig.

46).
The shoes slide axially in the cali-

per abutments by means of the tabs

which ride on machined ledges (bridg-

es) when hydraulic pressure is applied

to the piston (Fig. 6). A shoe and lin-

ing assembly consists of friction mate-

rial riveted to a metal plate called the

shoe.
It is replaced as a unit. Clips are

attached to the top of the caliper to

retain the shoe and lining assemblies.

The caliper assembly is mounted on

the front wheel spindle to the rear of

the wheel vertical centerline.

ROTOR

The cast iron disc is of the ventilat-

ed rotor-type incorporating forty fins

and is attached to, and rotates with

the wheel hub. A splash shield bolted

to the spindle is used primarily to pre-

vent road contaminants from contact-

ing the inboard rotor and lining sur-

faces.
The wheel provides protection

for the outboard surface of the rotor.

DRUM BRAKE

The drum brake system employs

single anchor, internal expanding ancj

self adjusting brake assemblies.

The self-adjusting brake mechanism

consists of a cable, cable guide, ad-

justing lever, adjusting screw assem-

bly, and adjuster spring (Fig. 8). The

cable is hooked over the anchor pin at

the top and is connected to the lever

at the bottom. The cable is routed

along the webb of the secondary brake

shoe by means of the cable guide. The

adjuster spring is hooked to the pri-

mary brake shoe and to the lever. The

automatic adjuster operates only when

the brakes are applied while the vehi-

cle is moving rearward and only when

the secondary shoe is free to move

toward the drum beyond a predeter-

mined point.
CALIPER
HOUSING

PISTON

SHOE

LINING

PISTON SEAL

FIG. 5—Floating Caliper Assembly—Sectional View

CALIPER
TO
ROTOR
CLEARANCE

CALIPER
HOUSING

PISTON

SHOE

LINING

PISTON SEAL
H 1568-B

TRANSFER
TUBE

PISTON DUST BOOT

RETAINING
GROVE

CALIPER
DUST

BOOT
RETAINER

H 1648-A

FIG.
6—Fixed
Caliper Assembly—Sectional View

PISTON
PISTON SEAL
RELAXED

CALIPER
HOUSING

BRAKES APPLIED

FIG. 7—Function of Piston Seal
BRAKES RELEASED

H1569-Bprocarmanuals.com

02-02-07
Brake System

02-02-07

ANTI-SKID CONTROL SYSTEM

RELEASE PAWL CAM PIN

RELEASE PAWL CAM LEVER

RELEASE CABLE

H
1636-
A

FIG. 10—Parking Brake Control Assembly

With Manual Release—Typical

power unit with mounting bracket is

riveted to the control assembly. The

vacuum actuated piston within the

unit is connected by a rod to the

upper end of the release lever (Fig. 9).

The lower end of the release lever ex-

tends out for alternate manual release
in the event of vacuum power failure

or for optional manual release at any

time.

Hoses connect the power unit and

the engine manifold to a vacuum re-

lease valve in the transmission neutral

safety switch.
The anti-skid control system con-

sists of three major components (Fig.

39).
Mechanically driven electromag-

netic sensors at each rear wheel; an

electronic control module mounted

under the glove box; a vacuum pow-

ered actuator attached to a bracket on

the inside of the right front frame rail

under the toe board.

The sensors consist of steel rings

having teeth on their outer diameters,

pressed on each axle shaft just out-

board of the wheel bearing. The teeth

rotate past corresponding teeth on the

inside diameter of stationary steel

rings mounted in the bearing retain-

ers.
Also mounted in the retainers, are

ring-shaped permanent magnets and

coils of wire. Two wires from each

sensor connect the sensors to the con-

trol module.

The control module consists of solid

state electronic components sealed in

a container. It is connected to the sen-

sors and to a solenoid on the actuator.

The actuator is similar to a vacuum

brake booster and consists of three

parts.
A chamber divided by a vacuum

suspended diaphragm; a hydraulic cyl-

inder connected to the diaphragm; and

a solenoid connected electrically to the

control module.

IN-VEHICLE ADJUSTMENTS AND REPAIRS

After any brake service work, ob-

tain a firm brake pedal before moving

the vehicle. Riding the brake pedal

(common on left foot application)

should be avoided when driving the

vehicle.

BRAKE SHOE ADJUSTMENTS—

DRUM BRAKES

The hydraulic drum brakes are

self-adjusting and require a manual

adjustment only after the brake shoes

have been relined, replaced, or when

the length of the adjusting screw has

been changed while performing some

other service operation. The manual

adjustment is performed with the

drums removed, using the tool and the

procedure detailed below.

When adjusting the rear brake

shoes,
check the parking brake cables

for proper adjustment. Make sure that

the equalizer operates freely.
To adjust the brake shoes:

1.
Use Rotunda Tool HRE 8650,

(Fig. 11) to determine the inside diam-

eter of the drum braking surface.

2.
Reverse the tool as shown in Fig.

11 and adjust the brake shoe diameter

to fit the gauge. Hold the automatic

adjusting lever out of engagement

while rotating the adjusting screw, to

prevent burring the screw slots. Make

sure the adjusting screw rotates freely.

If necessary, lubricate the adjusting

screw threads with a thin, uniform

coating of MIC-100-A.

3.
Rotate Tool HRE 8650 around

the brake shoes to be sure of the set-

ting.

4.
Apply a small quantity of high

temperature grease to the points

where the shoes contact the backing

plate, being careful not to get the lu-

bricant on the linings.

5. Install the drums. Install Tinner-

man nuts and tighten securely.

6. Install the wheels on the drums
and tighten the nuts to specification.

7.
Complete the adjustment by

applying the brakes several times with

a minimum of 50 lbs pressure on the

pedal while backing the vehicle. After

each stop the vehicle must be moved

forward.

8. After the brake shoes have been

properly adjusted, check the operation

of the brakes by making several stops

while operating in a forward direction.

WHEEL CYLINDER REPAIR-

DRUM BRAKE

Wheel cylinders should not be di-

sassembled unless they are leaking or

unless new cups and boots are to be

installed. It is not necessary to remove

the brake cylinder from the backing

plate to disassemble, inspect, or hone

and overhaul the cylinder. Removal is

necessary only when the cylinder is

damaged or scored beyond repair.procarmanuals.com

02-02-08
Brake System

02-02-08

Tool-HRE-8650

JUST SET TO DRUM

DIAMETER HERE . . .
FIND CORRECT BRAKE

SHOE DIAMETER HERE

H1416-A

FIG.
7
7—Adjusting Brake Shoes Using Tool HRE-8650

BOOT

BOOT

PISTON
. BLEEDER .

CYLINDER
SCREW RETURN SPRING PIST0N

H1385-B

FIG. 72—Brake Wheel Cylinder—Typical

DISASSEMBLY

1.
Remove the links and the rubber

boots from the ends of the brake cyl-

inder. Remove the pistons, cups, and

return spring from the cylinder bore

(Fig. 12).

2.
Remove the bleeder screw from

the cylinder.

INSPECTION

1.
Wash all parts in clean brake

fluid. Dry with compressed air.

2.
Replace scored pistons. Always

replace the rubber cups and dust

boots.
3.
Inspect the cylinder bore for

score marks or rust. If either condi-

tion is present the cylinder bore must

be honed. However, the cylinder

should not be honed more than 0.003

inch beyond its original diameter.

4.
Check the bleeder hole to be sure

that it is open.

ASSEMBLY

1.
Apply a light coating of heavy-

duty brake fluip! to all internal parts.

2.
Thread the bleeder screw into the

cylinder and tighten securely.

3.
Insert the return spring, cups,

and pistons into their respective posi-

tions in the cylinder bore (Fig. 12).
Place a boot over each end of the cyl-

inder. Bleed the brake system.

HYDRAULIC LINE REPAIR

Steel tubing is used throughout the

brake system with the exception of the

flexible hoses at the front wheels and

at the fear axle housing brake tube

connection (Figs. 17 thru 21).

Always bleed the applicable pri-

mary or secondary brake system after

primary or secondary brake system

hose or line replacement. Centralize

the pressure differential valve after

bleeding the system.

BRAKE TUBE

REPLACEMENT

If a section of the brake tubing be-

comes damaged, the entire section

should be replaced with tubing of the

same type, size, shape and length.

Copper tubing should not be used in a

hydraulic system. When bending

brake tubing to fit underbody or rear

axle contours, be careful not to kink

or crack the tube.

All brake tubing should be double

flared properly to provide good leak-

proof connections. Clean the brake

tubing by flushing with clean brake

fluid before installation.

When connecting a tube to a hose,

tube connector, or brake cylinder,

tighten the tube fitting nut to specified

torque with Milbar tool 1112-144 or

equivalent.

BRAKE HOSE

REPLACEMENT

A flexible brake hose should be re-

placed if it shows signs of softening,

cracking, or other damage.

When installing a new front brake

hose,
position the hose to avoid con-

tact with other chassis parts. Place a

new copper gasket over the hose fit-

ting and thread the hose assembly into

the front wheel cylinder. Engage the

opposite end of the hose to the brack-

et on the frame. Install the horsesho-

e-type retaining clip, and connect the

tube to the hose with the tube fitting

nut (Figs. 17 thru 21).

A rear brake hose should be in-

stalled so that it does not touch the

muffler outlet pipe or shock absorber.

Thread the hose into the rear brake

tube connector. Engage the front end

of the hose to the bracket on the

frame. Install the horseshoe-type re-

taining clip, and connect the tube to

the hose with the tube fitting nut.procarmanuals.com

02-02-17
Brake System

02-02-17

CALIPER PARTS

2B120 R.H.

2B121 L.H.

CALIPER ASS'Y

2B118 R.H.

2BU9L.H.

INSULATOR

CUP
2B2"

2B164
STABILIZER

2B295

FAIRLANE, MONTEGO, FALCON,

MUSTANG AND COUGAR
SEAL

2B115

2207

BOOT
20310-S

34806 S \ INNER BEARING

w CONE AND ROLLER

1201

CUP
ANCHOR PLATE

2B293 L.H.

2B292 R.H.

CONE AND ROLLER

1216

GREASE SEAL

1190

ADJUSTING NUT

374504-S
3105-R.H.

3106-L.H.

ROTOR SPLASH SHI

2K004-R.H.

2K005-L.H.

COVER-1130

1102

H 1670-A

FIG. 23—Disc Brake—Disassembled—All Models Except Lincoln

cylinder fluid level and add the speci-

fied fluid, as required. Pump the

brake pedal several times to actuate

the piston seals and to position the

shoe and lining assemblies.

5. Install the wheel and tire assem-

bly and the wheel cover.

6. Road test the vehicle.
LINCOLN CONTINENTAL

Removal

Refer to Fig. 24.

1.
Remove the front wheel cover.
Remove the wheel and tire assembly

from the hub and rotor assembly. Be

careful to avoid damage or interfer-

ence with the caliper splash shield,

bleeder screw fitting or transfer tube.

2.
Disconnect the steel brake line

transfer tube from the caliper (Fig.

21).
Leave the steel tube connected to

CALI PER PARTS-2B120-R.H. -2B121-L.H.

CALIPER ASSEMBLY

*2B118-R.H.

•2B119-L.H.
34811-S

SPINDLE
379726-S
INBOARD HOUSING

PISTON SEALS (4)-2B115

/PISTONS (4) -2196 OUTBOARD HOUSING

T BOOTS (4) 2207
CLIP

34806-S
INNER BEARING

CONE AND ROLLER

1201

GASKET

3105-R.H.
2B16°

3106-L.H.

ROTOR SPLASH
SHI
EL

1102
SHOE AND LINING

ASSEMBLIES -2018

COVER-US'!

H 1650-A

FIG. 24—Disc Brake Disassembled—Lincoln Continentalprocarmanuals.com

02-02-20
Brake System

02-02-20

1.
Disconnect the stoplight switch

wires at the connector. Remove the

spring retainer. Slide the stop light

switch off the brake pedal pin just far

enough to clear the end of the pin,

then liftfthe switch straight upward

from the pin. Use care to avoid switch

damage during removal.

2.
Slide the master cylinder push

rod and the nylon washers and bush-

ings off the brake pedal pin.

3.
Remove the brake tube from the

primary and secondary outlet ports of

the master cylinder.

4.
Remove the cap screws and lock-

washers that secure the master cylin-

der to the dirSh panel and lift the cyl-

inder forward and upward from the

vehicle.

Installation

1.
Position the boot on the push

rod and secure the boot to the master

cylinder. Carefully insert the master

cylinder push rod and boot through

the dash panel opening and position

the master cylinder on the panel.

2.
Install the cap screws at the dash

panel and torque them to specifica-

tion.

3.
Coat the nylon bushings with

SAE 10W oil. Install the nylon wash-

er and bushing on the brake pedal pin.

4.
Position the stop light switch on

the brake pedal pin, install the nylon

bushing and washer and secure them

in position with the spring retainer.

5.
Connect the wires at the stop

light switch connector.

6. Connect the brake lines to the

master cylinder leaving the brake line

fittings loose.

7.
Fill the master cylinder with the

specified brake fluid to within 1/4

inch of the top of the dual reservoirs.

Use Ford Brake Fluid— Extra Heavy

Duty-Part Number C6AZ-19542-A

(ESA-M6C25-A) or equivalent for all

drum brake applications. The extra

heavy duty brake system fluid is col-

ored blue for identification. Do not

mix low temperature brake fluids with

the specified fluid for the power disc

brake system.

8. Bleed the dual-master cylinder

and the primary and secondary brake

systems. Centralize the pressure dif-

ferential valve. Refer to Hydraulic

System Bleeding and Centralizing of

the Differential Valve, Part 2-1, Sec-

tion 2 for proper procedure.

9. Operate the brakes several times,

then check for external hydraulic

leaks.
FAIRLANE, MONTEGO,

FALCON, MUSTANG AND

COUGAR

Removal

Refer to Figs. 27 and 28.

1.
Working from inside the vehicle

below the instrument panel, disconnect

the master cylinder push rod from the

brake pedal assembly. The push rod

cannot be removed from the master

cylinder.

2.
Disconnect the stoplight switch

wires at the connector. Remove the

hairpin retainer. Slide the stop light

switch off the brake pedal pin just far

enough to clear the end of the pin,

then lift the switch straight upward

from the pin. Use care to avoid switch

damage during removal.

3.
Slide the master cylinder push

rod and the nylon washers and bush-

ings off the brake pedal pin.

4.
Remove the brake tubes from

the primary and secondary outlet

ports of the master cylinder.

5.
Remove the lock nuts or cap

screw and lockwashers that secure the

master cylinder to the dash panel and

lift the cylinder forward and upward

from the car.
Installation

Refer to Figs. 27 and 28.

1.
Position the boot on tie push

rod and secure the boot to the master

cylinder. Carefully insert the master

cylinder push rod and boot through

the dash panel opening.

2.
On Fairlane, Falcon or Montego

models, position the gasket and mas-

ter cylinder on the mounting studs on

the dash panel. Install the lock nuts

on the studs at the dash panel and

torque them to specification.

3.
On Mustang or Cougar models,

position the gasket and master cylin-

der on the dash panel. Install the re-

taining screws and torque them to

specification. Coat the nylon bushings

with SAE 10W oil. Install the nylon

washer and bushing on the brake

pedal pin.

4.
Position the stop light switch on

the brake pedal pin, install the nylon

bushing and washer and secure them

in position with the spring retainer.

5.
Connect the wires at the stop

light switch connector.

6. Connect the brake lines to the

master cylinder and tighten to speci-

fied torque.

7.
Fill the master cylinder with the

specified brake fluid to within 1/4

MASTER CYLINDER

IDENTIFICATION
UPPER STUD

SHAFT (AUTOf/lATIC

TRANSMISSION)

CLIP

BRAKE PEDAL

BUSHING SUPPORT

TUBE-2B253

TUBE-2A040
CLUTCH

PEDA_

LOWER STUD
STOP LITE

SWITCH

/ 13480

MASTER CYLINDER

PUSH ROD
BRAKE PEDAL

H 1556-C

FIG. 27—Dual Master Cylinder Installation—Non Power Brake

Fairlane, Montego, and Falconprocarmanuals.com

02-02-24
Brake
System

02-02-24

proportioning valve to the fender

apron and remove the proportioning

valve.

Installation

1.
Position the proportioning valve

to the fender apron.

2.
Connect the two brake lines at

the proportioning valve. Do not tight-

en.

3.
Install the bolt retaining the pro-

portioning valve to the fender apron.

4.
Tighten the brake line tube nuts

at the proportioning valve to specifica-

tions.

5.
Bleed the brakes and centralize

pressure differential valve.

THUNDERBIRD AND

CONTINENTAL MARK III

Removal

Refer to Fig. 20.

1.
Disconnect the two hydraulic

brake lines at the master cylinder.

2.
Remove the two nuts retaining

the master cylinder to the booster and

remove the master cylinder for clear-

ance.

3.
Disconnect the two brake lines at

the proportioning valve.

4.
Remove the bolt and nut retain-

ing the proportioning valve to the

pressure differential valve bracket and

remove the proportioning valve assem-

bly.

Installation

1.
Transfer the bracket to the new

proportioning valve.

2.
Position the proportioning valve

assembly to the pressure differential

valve bracket.

3.
Connect the two brake lines to

the proportioning valve. Do not tight-

en.

4.
Install the bolt and nut retaining

the proportioning valve to the pressure

differential valve bracket.

5.
Tighten the two brake line tube

nuts at the proportioning valve to

specifications.

6. Position the master cylinder to

the booster and install the nuts retain-

ing the master cylinder to the booster.

7.
Connect the two brake lines at

the master cylinder and tighten the

tube nuts to specifications.

8. Bleed the brakes and centralize

the pressure differential valve.
LINCOLN CONTINENTAL

Removal

Refer to Fig. 21.

1.
Disconnect the two brake lines at

the proportioning valve.

2.
Loosen the bolt and nut on the

bracket retaining the proportioning

valve to the chassis.

3.
Remove the proportioning valve

from the bracket.

Installation

- 1. Position the proportioning valve

in the bracket and connect the two

brake lines. Do not tighten.

2.
Tighten the bolt and nut on the

bracket.

3.
Tighten the tube nuts on the

brake lines at the proportioning valve

to specifications.

4.
Bleed the brakes and centralize

the pressure differential valve.

PRESSURE METERING VALVE—

LINCOLN CONTINENTAL

REMOVAL

Refer to Fig. 21.

1.
Loosen the tube nuts connecting

the inlet and outlet tubes at the me-

tering valve, and remove the tubes.

2.
Remove the two screws retaining

the metering valve to the frame

crossmember, and remove the me-

tering valve. The metering valve is ser-

viced as an assembly only.

INSTALLATION

1.
Position the metering valve to

the frame crossmember, and install

the retaining screws.

2.
Connect the inlet and outlet

tubes to the metering valve, and tight-

en the tube nuts to specification.

BRAKE BOOSTER

REMOVAL

1.
Working from inside the\ vehicle

below the instrument panel, disconnect

the booster push rod from the brake

pedal assembly. To do this, proceed as

follows:

Disconnect the stop light switch

wires at the connector. Remove the

hairpin retainer. Slide the stop light
switch off from the brake pedal pin

just far enough for the switch outer

hole to clear the pin, and then remove

the switch from the pin and booster

push rod. Be careful not to damage

the switch during removal. Slide the

booster push rod and the nylon wash-

ers and bushing off the brake pedal

pin (Figs. 29 thru 33).

2.
Open the hood and remove the

master cylinder from the booster. Se-

cure it to one side without disturbing

the hydraulic lines. It is not necessary

to disconnect the brake lines, but care

should be taken that the brake lines

are not deformed. Permanent defor-

mation of brake lines can lead to tube

failure.

3.
Disconnect the manifold vacuum

hose or hoses from the booster unit.

4.
Remove the booster-to-dash

panel attaching nuts or bolts (Figs. 29

thru 33). Remove the booster and

bracket assembly from the dash panel,

sliding the push rod link out from the

engine side of the dash panel.

5.
On Fairlane, Montego, and Fal-

con models, remove the push rod link

boot from the dash panel.

INSTALLATION

1.
On Fairlane, Montego and Fal-

con models, install the push rod link

boot in the hole in the dash panel as

shown in Fig. 23. Install the four

spacers on the mounting studs.

2.
Mount the booster and bracket

assembly to the dash panel by insert-

ing the push rod or push rod link in

through the hole and boot in the dash

panel. Install the bracket-to-dash

panel attaching lock nuts or bolts

(Figs.
29 thru 33).

3.
Connect the manifold vacuum

hose or hoses to the booster.

4.
Before installing the master cyl-

inder, check the distance from the

outer end of the booster assembly

push rod to master cylinder surface.

Turn the screw in or out to obtain the

specified length. Refer to Part 2-1,

Section 2, Power Brake Master Cylin-

der Push Rod Adjustment. Install the

master cylinder and torque the attach-

ing nuts to specifications.

5.
Working from inside the vehicle

below the instrument panel, connect

the booster push rod link to the brake

pedal assembly. To do this, proceed as

follows:

Install the inner nylon washer, the

booster push rod, and the bushing on

the brake pedal pin. Position the

switch so that it straddles the push

rod with the switch slot on the pedal

pin and the switch outer hole justprocarmanuals.com

02-02-39
Brake System

02-02-39

MAJOR REPAIR OPERATIONS

BRAKE DRUM REFINISHING

Minor scores on a brake drum can

be removed with sandpaper. A drum

that is excessively scored or shows a

total indicator runout of over 0.007

inch should be turned down. Remove

only enough stock to eliminate the

scores and true up the drum. The refi-

nished diameter must not exceed 0.060

inch oversize.

Check the inside diameter of the

brake drum with a brake drum mi-

crometer (Tool FRE-14^1).

If the drum diameter is less than

0.030 inch oversize after refinishing^

standard lining may be installed. If

the drum diameter is 0.030—0.060

inch oversize after refinishing, oversize

lining must be installed.

After a drum is turned down, wipe

the refinished surface with a cloth

soaked in clean denatured alcohol. If

one drum is turned down, the opposite

drum on the same axle should also be

cut down to the same size.

ROTOR REFINISHING

Rotunda Disc Brake Attachment,

FRE-2249-2, is the only recommended

tool to refinish the disc brake rotors.

The step-by-step resurfacing procedure

provided with the tool must be ad-

hered to.

The finished braking surfaces of the

rotor must be flat and parallel within

0.0007 inch; lateral runout must not

exceed 0.003 inch total indicator read-

ing, and the surface finish of the brak-

ing surfaces are to be 80/15 micro

inches. The minimum limiting dimen-

sions (Figs. 11 and 12, Part 2-1) from

the inboard bearing cup to the out-

board rotor face and from the inboard

bearing cup to the inboard rotor face

must be observed when removing ma-

terial from the rotor braking surfaces.

On all models except Lincoln Con-

tinental, the limiting dimensions are to

be measured with a ball and gage bar

(Rotunda Kit FRE-70160).

BRAKE SHOE RELINING

Brake linings that are worn to with-

in 1/32 inch of the rivet head or are

less than 0.030 inch thick (bonded lin-

ing) or have been contaminated with

brake fluid, grease or oil must be re-

placed. Failure to replace worn linings

will result in a scored drum. When it
is necessary to replace linings, they

must also be replaced on the wheel on

the opposite side of the vehicle.

Inspect brake shoes for distortion,

cracks, or looseness. If this condition

exists,
the shoe must be discarded. Do

not attempt to repair a defective brake

shoe.

1.
Wash the brake shoes thoroughly

in a clean solvent. Remove all burrs

or rough spots from the shoes.

2.
Check the inside diameter of the

brake drum with a brake drum mi-

crometer (tool FRE-1431). If the di-

ameter is less than 0.030 inches over-

size,
standard lining may be installed.

If the diameter is 0.030—0.060 inches

oversize, oversize lining should be in-

stalled.

3.
Position the new lining on the

shoe.
Starting in the center, insert and

secure the rivets, working alternately

towards each end. Replacement lin-

ings are ground and no further grind-

ing is required.

4.
Check the clearance between the

shoe and lining. The lining must seat

tightly against the shoe with not more

than 0.008 inch clearance between any

two rivets.

RETAINER - 2B245
DUAL MASTER CYLINDER

DISASSEMBLY

1.
Clean the outside of the master

cylinder and remove the filler cover

and diaphragm. Pour out any brake

fluid that remains in the cylinder. Dis-

card the old brake fluid.

2.*
Remove the secondary piston

stop bolt from the bottom of the cyl-

inder (Figs. 40 and 41).

3.
Remove the bleed screw, iL re-

quired.

4.
Depress the primary piston and

remove the snap ring from the retain-

ing groove at the rear of the master

cylinder bore (Fig. 42). Remove the

push rod and the primary piston as-

sembly from the master cylinder bore.

Do not remove the screw that retains

the primary return spring retainer, re-

turn spring, primary cup and protec-

tor on the primary piston. This assem-

bly is factory pre-adjusted and should

not be disassembled.

5.
Remove the secondary piston as-

sembly. Do not remove the outlet tube

seats,
outlet check valves and outlet

SECONDARY SYSTEM

BRAKE OUTLET
COVER -2166

GASKET-2167

MASTER CYLINDER -2155

SNAP RING -7821

BOOT

PUSH ROD

PRIMARY PISTON

ASSEMBLY - 2169

tTUBE SEAT-

2B220
* SECONDARY PISTON

ASSEMBLY - 2A502

• NOT USED ON POWER BRAKE EQUIPPED VEHICLES

fNOT SERVICED

•REPLACE AS AN ASSEMBLY ONLY

H 1499-B

FIG. 40— Dual Master Cylinder Disassembled—Except Disc Brakesprocarmanuals.com

02-02-40
Brake System

02-02-40

RETAINER - 2B245

PRIMARY PISTON

ASSEMBLY-2169

GASKET-2167

RETURN SPRING

RETAINER

\ CUP

\\PROTECTOR

^\i # PISTON
fNOT SERVICED

* REPLACE AS

ASSEMBLY ONLY

*O-RING

PUMPING CUP

tVALVE

2175

SECONDARY

BRAKE SYSTEM

OUTLET
*SECONDARY PISTON

ASSEMBLY-2A502

H 1550-B

FIG. 41—Dual Master Cylinder Disassembled—Disc Brakes

check valve springs from the master

cylinder body.
open and free of foreign matter. Use

an air hose to blow out dirt and clean-

ing solvent. Place all parts on a clean

pan or paper.

3.
Inspect the master cylinder bore

for signs of etching, pitting, scoring or

rust. If it is necessary to hone the

master cylinder bore to repair dam-

age,
do not exceed allowable hone

specifications.

ASSEMBLY

1.
Dip all parts except the master

cylinder body in clean Rotunda Extra

Heavy Duty Brake Fluid.

2.
Carefully insert the complete

secondary piston and return spring as-

sembly in the master cylinder bore.

3.
Install the primary piston assem-

bly in the master cylinder bore.

4.
Depress the primary piston and

install the snap ring in the cylinder

bore groove.

5.
Install the push rod, boot and re-

tainer on the push rod, if so equipped.

Install the push rod assembly into the

primary piston. Make sure the retain-

er is properly seated and holding the

push rod securely.

6. Position the inner end of the

push rod boot (if so equipped) in the

master cylinder body retaining groove.

7.
Install the secondary piston stop

INSPECTION AND REPAIR

1.
Clean all parts in clean isopropyl

alcohol, and inspect the parts for

chipping, excessive wear or damage.

When using a master cylinder repair

kit, install all the parts supplied.

2.
Check all recesses, openings and

internal passages to be sure they are

Snap Ring Pliers

SNAP RING

H1477-C

FIG. 42—Removing Snap

Ring—Typical
INNER BRAKE

SHOE AND LINING

ASSEMBLY-2019
OUTER SHOE

RETAINING CLIPS

2066

STABILIZER

2B295

LOCATING PIN

2B296

ANCHOR PLATE

2B293(L.H.)

2B292 (R.H.)
MOVABLE CALIPER

2B119(L.H.)

2B118(R.H.)

H 1573-C

FIG. 43—Caliper Assembly—Disassembled-

All Models Except Lincoln Continentalprocarmanuals.com